Benutzeranleitung / Produktwartung 16HA des Produzenten Q-Logic
Zur Seite of 122
Preliminar y SANbox-16HA High A vailability Fibre Channel Switch Installer’ s/User’ s Manual Publication No. 59005-03 Rev . A.
Preliminar y QLogic Corporation 6321 Bury Drive Eden Prairie, MN 55346 (952) 932-4000 Release Number 03, Revision A ( August, 2000) The following paragraph does not apply to the United Kingdom or any .
Preliminar y SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A iii T able of Contents Preface How to Use This Manual 1 Intended Audience 1 Related Materials 2 Safety No.
Preliminar y SANbox-16HA Fibre Channel Switch iv 59005-03 Rev . A Installer’ s/User’ s Manual Power Switches 1-19 T est Mode Switch 1-19 Front Panel LEDs 1-20 Heartbeat LED (Y ellow) 1-20 Switch L.
Preliminar y SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A v TL_Ports 2-19 T_Ports 2-19 T uning Ports for Multi-Frame Sequences 2-20 Zoning 2-21 Rack and Shelf Admi.
Preliminar y SANbox-16HA Fibre Channel Switch vi 59005-03 Rev . A Installer’ s/User’ s Manual Mesh Latency 5-9 Mesh Bandwidth 5-10 Mesh Physical Distance Between Chassis 5-10 Mesh Zoning 5-11 MKII.
Preliminar y SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A vii B QLogic Customer Support Help Desk B-1 Hardware Support B-1 Software Support B-2 Customer Responsibi.
Preliminar y SANbox-16HA Fibre Channel Switch viii List of Figures and T ables 59005-03 Rev . A Installer’ s/User’ s Manual List of Figures and T ables Figure 1-1 SANbox-16HA Fibre Channel Switch .
Preliminar y SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Preface 1 Preface How to Use This Manual This manual has five sections and tw o appendix es: • Section 1 is an o verview of the Switch. It describes indicator lights and all user controls and connections.
Preliminar y SANbox-16HA Fibre Channel Switch 2 Preface 59005-03 Rev . A Installer’ s/User’ s Manual Related Materials The follo wing manuals and materials are referenced in the text and/or pro vide additional information. • Switch Management Installer’ s/User’ s Manual, Publication Number 59010.
Preliminar y SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Preface 3 Safety Notices A Danger notice indicates the presence of a hazard that has the potential of causing death or serious personal injury .
Preliminar y SANbox-16HA Fibre Channel Switch 4 Preface 59005-03 Rev . A Installer’ s/User’ s Manual C ommunications Statements The follo wing statements apply to this product. The statements for other products intended for use with this product appear in their accompan ying manuals.
Preliminar y SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Preface 5 CE Statement The CE symbol on the equipment indicates that this system complies with the EMC (Electromagnetic Compatibility) directi ve of the European Community (89/ 336/EEC) and to the Lo w V oltage (Safety) Directi ve (73/23/EEC).
Preliminar y SANbox-16HA Fibre Channel Switch 6 Preface 59005-03 Rev . A Installer’ s/User’ s Manual VCCI Class A Statement T ranslation: This is a Class A product based on the standard of the V oluntary Control Council F or Interference by Information T echnolo gy Equipment (VCCI).
Preliminar y SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Preface 7 Laser Safety Information This product ma y use Class 1 lasers to communicate o ver the fiber optic conduc- tors. The U .S. Depar tment of Health and Human Services (DHHS) does not consider Class 1 lasers to be hazardous.
Preliminar y SANbox-16HA Fibre Channel Switch 8 Preface 59005-03 Rev . A Installer’ s/User’ s Manual Accessible Parts The onl y Field Replaceab le Units (FR Us) in the SANbox-16HA F ibre Channel Switch are: • Fuses associated with the A C po wer input, • P o wer suppl y(s), and • Interfaces to the interconnection media called GBICs.
Preliminar y SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Preface 9 QLogic Customer Support Phone: (952) 932-4040 F ax: (952) 932-4018 Attn: Customer Support E-Mail: support@QLogic.com W eb: www .QLogic.com Please refer Appendix B QLo gic Customer Suppor t for an explanation of QLo gic Customer Support.
SANbox-16HA Fibre Channel Switch Preface 59005-03 Rev . A Installer’ s/User’ s Manual Notes.
Preliminar y SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A General Description 1-1 Section 1 General Description Introduction The SANbox™-16HA High A vailability F ibre Channel (FC) Switch is the F abric component of a Fibre Channel compliant netw ork.
Preliminar y Major Fibre Channel Port Features SANbox-16HA Fibre Channel Switch 1-2 General Description 59005-03 Rev . A Installer’ s/User’ s Manual Major Fibre Channel Port Features Major Fibre Channel port features include: • Each Switch chassis has 16 Fibre Channel ports.
Preliminar y Major Fibre Channel Port Features SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A General Description 1-3 • Y ou ma y populate 2 to 16 por ts with GBICs. The choice of por ts and GBICs is yours. The Switch has been v alidated with GBICs that support a variety of intercon- nection media.
Preliminar y Major Fibre Channel Port Features SANbox-16HA Fibre Channel Switch 1-4 General Description 59005-03 Rev . A Installer’ s/User’ s Manual Figure 1-2 sho ws a possib le topology of a Se gmented Loop.
Preliminar y Major Fibre Channel Port Features SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A General Description 1-5 • Devices in the same se gmented loop zone communicate with one another as though they w ere on the same ph ysical loop.
Preliminar y Major Fibre Channel Port Features SANbox-16HA Fibre Channel Switch 1-6 General Description 59005-03 Rev . A Installer’ s/User’ s Manual T ranslated Loop Port (TL_Port) Over view Y ou ma y use Switch management to configure any or all ports on the SANbox-16 chassis as T ranslated Loop por ts (TL_P or ts).
Preliminar y Major Fibre Channel Port Features SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A General Description 1-7 TCP/IP protocols are also supported.
Preliminar y Major Fibre Channel Port Features SANbox-16HA Fibre Channel Switch 1-8 General Description 59005-03 Rev . A Installer’ s/User’ s Manual • The set of off-loop de vices that a single TL_P or t ma y proxy ma y o verlap or exclude the de vices accessed by other TL_P or ts in the same fabric.
Preliminar y Major Switch Chassis Features SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A General Description 1-9 TL_Port Management Refer to the Switch Management manual for more information. SANsurfer Switch management pro vides the follo wing: • The user ma y choose which ports (if any) are TL_P or ts.
Preliminar y Major Switch Chassis Features SANbox-16HA Fibre Channel Switch 1-10 General Description 59005-03 Rev . A Installer’ s/User’ s Manual • Each chassis has tw o separate A C pow er inputs, one for each po wer suppl y . The left A C po wer input pro vides input po w er to the left po w er supply .
Preliminar y Major Switch Management Features SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A General Description 1-11 Major Switch Management Features Switch managem.
Preliminar y Major Switch Management Features SANbox-16HA Fibre Channel Switch 1-12 General Description 59005-03 Rev . A Installer’ s/User’ s Manual • P erform T race operations to follo w selec.
Preliminar y Major Switch Management Features SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A General Description 1-13 Name Serv er Zoning b y W orld Wide Name Name s.
Preliminar y Major Switch Management Features SANbox-16HA Fibre Channel Switch 1-14 General Description 59005-03 Rev . A Installer’ s/User’ s Manual • Configure Loop Devices including: - Place .
Preliminar y Switch Management Tools SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A General Description 1-15 Switch Management T ools The Switch supports switch management primaril y through the follo wing tools. Refer to the Switch Management Manual for information about these tools.
Preliminar y Switch Management Tools SANbox-16HA Fibre Channel Switch 1-16 General Description 59005-03 Rev . A Installer’ s/User’ s Manual • Set or read the IP netw ork configuration • Read .
Preliminar y Fibre Channel Ports SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A General Description 1-17 Fibre Channel Ports Figure 1-5 identifies the parts of the chassis front. P or t numbers are marked on the front of the chassis.
Preliminar y Fibre Channel Ports SANbox-16HA Fibre Channel Switch 1-18 General Description 59005-03 Rev . A Installer’ s/User’ s Manual GigaBit Interface Converters (GBICs) Cur rentl y , the follo.
Preliminar y Front Panel Controls SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A General Description 1-19 Front Panel Controls Power Switches There are tw o P o w er Switches and Figure 1-5 sho ws their location. Figure 1-7 sho ws the right P o w er Switch.
Preliminar y Front Panel LEDs SANbox-16HA Fibre Channel Switch 1-20 General Description 59005-03 Rev . A Installer’ s/User’ s Manual Front Panel LEDs Refer to Figure 1-5 . LEDs visib le through lenses in the front of the chassis indicate chassis and port status.
Preliminar y Front Panel LEDs SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A General Description 1-21 Over T emperature LED (Red) This LED is normally OFF . The o ver temperature LED illuminates to indicate that the air temperature inside the switch has e xceeded a certain limit.
Preliminar y AC Input Power Connectors and Fuses SANbox-16HA Fibre Channel Switch 1-22 General Description 59005-03 Rev . A Installer’ s/User’ s Manual T raffic LED (Y ellow) Each port has its own P ort Activity LED . The P or t Activity LED for a particular port is ON when Class 2, or 3 frames are entering or lea ving the port.
Preliminar y Chassis Back SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A General Description 1-23 Chassis Back Refer to Figure 1-8 . The back of the chassis contains ba ys for tw o P o w er Supplies. The fan is par t of the po wer suppl y .
Preliminar y Chassis Back SANbox-16HA Fibre Channel Switch 1-24 General Description 59005-03 Rev . A Installer’ s/User’ s Manual Power Supply(s) The chassis has ba ys for tw o po w er supplies. When there is only one suppl y , it can operate from either ba y and the unused ba y is co vered with a plate.
Preliminar y SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Installation 2-1 Section 2 Installation Introduction There are nine basic steps required to install the Switch. 1. Unpack 2. Place or Mount the Equipment 3.
Preliminar y Place or Mount the Equipment SANbox-16HA Fibre Channel Switch 2-2 Installation 59005-03 Rev . A Installer’ s/User’ s Manual Place or Mount the Equipment The Switch ma y be placed on a flat surface and stacked , or mounted in a 19” EIA rack.
Preliminar y Place or Mount the Equipment SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Installation 2-3 The follo wing steps describe ho w to mount the chassis in a rack: 1. Mount the Brackets. The chassis must sit on rails or a shelf in the rack or cabinet.
Preliminar y Apply the IEC Class 1 Laser Information Label (If the installation is in Europe) SANbox-16HA Fibre Channel Switch 2-4 Installation 59005-03 Rev . A Installer’ s/User’ s Manual Apply the IEC Class 1 Laser Information Label (If the installation is in Europe) Refer to Figure 2-2 .
Preliminar y Install GBICs SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Installation 2-5 Install GBICs Y ou ma y populate y our Switch with 2 to 16 GBICs. The choice of ports and GBICs is yours. The Switch has been validated with GBICs that support a variety of inter - connection media.
Preliminar y Connect to AC Power SANbox-16HA Fibre Channel Switch 2-6 Installation 59005-03 Rev . A Installer’ s/User’ s Manual DANGER: This product is supplied with a 3-wire power cable and plug for the user’ s safety . Use this power cable in conjunction with a properly grounded outlet to avoid electrical shock.
Preliminar y Switch Logic Power Good LED SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Installation 2-7 Refer to Appendix A Reference Infor mation for Switch po w er requirements. 1. Connect the po wer cab le to the front of the chassis.
Preliminar y Cable Fibre Channel Devices to the Switch SANbox-16HA Fibre Channel Switch 2-8 Installation 59005-03 Rev . A Installer’ s/User’ s Manual Cable Fibre Channel Devices to the Switch There are tw o types of Fibre Channel de vices, Public and Pri vate.
Preliminar y Cable Fibre Channel Devices to the Switch SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Installation 2-9 Pri vate de vices connect to Segmented Loop P or ts (SL_P or ts) or T ranslated Loop P or ts (TL_P or ts).
Preliminar y Cable Fibre Channel Devices to the Switch SANbox-16HA Fibre Channel Switch 2-10 Installation 59005-03 Rev . A Installer’ s/User’ s Manual Distance The maximum distance betw een each adapter and the Switch depends on the type of GBICs and the type of cable installed.
Preliminar y Cable Fibre Channel Devices to the Switch SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Installation 2-11 Figure 2-3 sho ws a server connected to a switch that is cab led for 24 credits through port 5.
Preliminar y Cable Fibre Channel Devices to the Switch SANbox-16HA Fibre Channel Switch 2-12 Installation 59005-03 Rev . A Installer’ s/User’ s Manual Fiber Optic Connections K eys on “Duple x.
Preliminar y Cable Fibre Channel Devices to the Switch SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Installation 2-13 Public Loop Storage Devices Connected to Public Servers Figure 2-4 sho ws Pub lic Loop storage devices connected to FL_P or ts.
Preliminar y Cable Fibre Channel Devices to the Switch SANbox-16HA Fibre Channel Switch 2-14 Installation 59005-03 Rev . A Installer’ s/User’ s Manual Variety of Public Device Connections Figure 2-5 sho ws a v ariety of Public de vice connections.
Preliminar y Cable Fibre Channel Devices to the Switch SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Installation 2-15 Private Segmented Loop Connections Figure 2-6 sho ws the connection of Pri vate Loop servers and Pri vate Loop storage units.
Preliminar y Cable Fibre Channel Devices to the Switch SANbox-16HA Fibre Channel Switch 2-16 Installation 59005-03 Rev . A Installer’ s/User’ s Manual Private T ranslated Loop Connections Figure 2-7 is an e xample of T ranslated Loop por ts (TL_P or ts) used in conjunction with each other and with F and FL_P orts.
Preliminar y Configure the Chassis SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Installation 2-17 Configure the Chassis If this chassis is part of a Multi-Chassis fabric, f ollo w the instructions in “Chassis Configuration” on pag e 5-18 .
Preliminar y Configure the Ports SANbox-16HA Fibre Channel Switch 2-18 Installation 59005-03 Rev . A Installer’ s/User’ s Manual Configure the Ports Use Switch Management for all port configuration. Fabric Ports The default mode of each Switch por t is FL.
Preliminar y Configure the Ports SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Installation 2-19 TL_Ports The set of of f-loop devices pro xied b y a TL_Port is contained in its translation entries list.
Preliminar y Configure the Ports SANbox-16HA Fibre Channel Switch 2-20 Installation 59005-03 Rev . A Installer’ s/User’ s Manual T uning Ports for Multi-Frame Sequences In most circumstances, tuning of an indi vidual por t is not desirab le, and the default setting (Normal) should be left unchanged.
Preliminar y Zoning SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Installation 2-21 Zoning SANbox s witches use the follo wing types of zoning to restrict or extend.
Preliminar y Rack and Shelf Administration SANbox-16HA Fibre Channel Switch 2-22 Installation 59005-03 Rev . A Installer’ s/User’ s Manual Broadcast Zones Broadcast zones focus the distribution of broadcast messages to onl y those de vices that need to recei ve them.
Preliminar y SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Diagnostics/T roubleshooting 3-1 Section 3 Diagnostics/T roubleshooting Introduction This section contains information to help you diagnose and troubleshoot prob lems with your Switch.
Preliminar y Power Supply Troubleshooting SANbox-16HA Fibre Channel Switch 3-2 Diagnostics/T roubleshooting 59005-03 Rev . A Installer’ s/User’ s Manual Power Supply T roubleshooting T able 3-1 and T ab le 3-2 are troubleshooting matrix es for finding A C source po w er and P o w er Suppl y prob lems.
Preliminar y Power Supply Troubleshooting SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Diagnostics/T roubleshooting 3-3 Shaded text in ta ble denotes a bnormal indications.
Preliminar y Power Supply Troubleshooting SANbox-16HA Fibre Channel Switch 3-4 Diagnostics/T roubleshooting 59005-03 Rev . A Installer’ s/User’ s Manual Shaded text in table denotes abnormal indications. * The state of the Power Supply Fail LED is not applicable in a system with one Power Supply .
Preliminar y Power Supply Troubleshooting SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Diagnostics/T roubleshooting 3-5 F or example: 1.
Preliminar y Power-On-Self-Test (POST) SANbox-16HA Fibre Channel Switch 3-6 Diagnostics/T roubleshooting 59005-03 Rev . A Installer’ s/User’ s Manual Power -On-Self-T est (POST) Overview The Switch checks the state of the T est Mode s witch as par t of its po w er-up proce- dure.
Preliminar y Power-On-Self-Test (POST) SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Diagnostics/T roubleshooting 3-7 When POST is complete and er rors are encountered , the Switch uses the Heartbeat LED to blink an error code which describes the first fatal er ror encountered.
Preliminar y Power-On-Self-Test (POST) SANbox-16HA Fibre Channel Switch 3-8 Diagnostics/T roubleshooting 59005-03 Rev . A Installer’ s/User’ s Manual • Switch Management por t lo gic • Arbitra.
Preliminar y Power-On-Self-Test (POST) SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Diagnostics/T roubleshooting 3-9 Flash Checksum Failure/Switch Management Port (Ethernet) T ests Good (3 Blinks) The Switch is not operable The Flash checksum test verifies the inte g rity of the Flash data.
Preliminar y Power-On-Self-Test (POST) SANbox-16HA Fibre Channel Switch 3-10 Diagnostics/T roubleshooting 59005-03 Rev . A Installer’ s/User’ s Manual Fibre Channel Port Loop-back T est Failure (8 Blinks) This test runs in Continuous T est onl y .
Preliminar y Power-On-Self-Test (POST) SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Diagnostics/T roubleshooting 3-11 Switch Auto-Route T est Failure (10 Blinks) The Switch is operable.
Preliminar y Cable Continuity Tests SANbox-16HA Fibre Channel Switch 3-12 Diagnostics/T roubleshooting 59005-03 Rev . A Installer’ s/User’ s Manual Cable Continuity T ests When there is a problem communicating o ver a par ticular link and both the Switch and the N_P or t adapter pass their respectiv e tests, check the continuity of the cables.
Preliminar y SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Removal/Replacement Procedures 4-1 Section 4 Removal/Replacement Procedures Introduction The onl y Field Replaceab le Units (FR Us) in the Switch are the Input Fuses, GBICs, and the P o w er Supply(s).
Preliminar y Input Fuse SANbox-16HA Fibre Channel Switch 4-2 Removal/Replacement Procedures 59005-03 Rev . A Installer’ s/User’ s Manual Replacement 1. Insert the Fuse into the Fuse Holder . Refer to Appendix A Reference Infor- mation for fuse-type information.
Preliminar y GBIC SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Removal/Replacement Procedures 4-3 GBIC GBICs ma y be remo ved and replaced with the Switch po w er on without disrupting traf fic on other por ts. Removal 1.
Preliminar y GBIC SANbox-16HA Fibre Channel Switch 4-4 Removal/Replacement Procedures 59005-03 Rev . A Installer’ s/User’ s Manual T o remo ve GBICs that ha ve bail-operated latches, as sho wn in Figure 4-4 , use your finger -tip to rotate the bail outward , then pull on the bail to remo ve the GBIC.
Preliminar y GBIC SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Removal/Replacement Procedures 4-5 2. Slide the GBIC into the port opening (the spring-loaded door will open as you push the GBIC in). If y ou can only slide the GBIC in about an inch (2.
Preliminar y Power Supply SANbox-16HA Fibre Channel Switch 4-6 Removal/Replacement Procedures 59005-03 Rev . A Installer’ s/User’ s Manual Power Supply Removal If the Switch contains tw o P o w er Supplies, either supply is “Hot-Pluggab le”.
Preliminar y Battery SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Removal/Replacement Procedures 4-7 Replacement If the Switch contains tw o P o w er Supplies, either supply is “Hot-Pluggab le”.
Battery SANbox-16HA Fibre Channel Switch Removal/Replacement Procedures 59005-03 Rev . A Installer’ s/User’ s Manual Notes.
Preliminar y SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Multi-Chassis Fabrics 5-1 Section 5 Multi-Chassis Fabrics Introduction Y ou ma y use SANbo x Switch chassis as building blocks to build a multiple-chassis fabric that will expand the number of user ports beyond the number in an y one chassis.
Preliminar y Introduction SANbox-16HA Fibre Channel Switch 5-2 Multi-Chassis Fabrics 59005-03 Rev . A Installer’ s/User’ s Manual Three Multi-Chassis T opologies There are three basic multi-chassis topolo gies for SANbox Switches: Cascade, Mesh, and Multistage™.
Preliminar y Introduction SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Multi-Chassis Fabrics 5-3 Choosing a T opology The topolo gy you choose depends on the follo.
Preliminar y Introduction SANbox-16HA Fibre Channel Switch 5-4 Multi-Chassis Fabrics 59005-03 Rev . A Installer’ s/User’ s Manual Bandwidth Between Chassis Each T_P ort link betw een directl y connected chassis contributes 100 me gab ytes of bandwidth betw een those chassis.
Preliminar y Cascade Topology SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Multi-Chassis Fabrics 5-5 Cascade T opology The term “cascade” indicates that chassis are connected in a line “one-to-the- next”.
Preliminar y Cascade Topology SANbox-16HA Fibre Channel Switch 5-6 Multi-Chassis Fabrics 59005-03 Rev . A Installer’ s/User’ s Manual Cascade Fabric Size SANbox-16 chassis connected in Cascade topolo gy expand from tw o chassis to a maximum of eight chassis.
Preliminar y Cascade Topology SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Multi-Chassis Fabrics 5-7 Cascade Bandwidth A chassis in a Cascaded topolo gy divides its chassis interconnection bandwidth betw een adjacent chassis.
Preliminar y Cascade Topology SANbox-16HA Fibre Channel Switch 5-8 Multi-Chassis Fabrics 59005-03 Rev . A Installer’ s/User’ s Manual Cascade Zoning Sanbox Switch chassis support fabric-wide zones for all zone types. Broadcast Zones and Name Server Zones require no special consideration in a cascade fabric.
Preliminar y Mesh Topology SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Multi-Chassis Fabrics 5-9 Mesh T opology The term “mesh” indicates that each chassis has at least one T_P or t directly connected to each other chassis.
Preliminar y Mesh Topology SANbox-16HA Fibre Channel Switch 5-10 Multi-Chassis Fabrics 59005-03 Rev . A Installer’ s/User’ s Manual Mesh Bandwidth A chassis in a Mesh topolo gy di vides its chassis interconnection bandwidth among the other chassis in the fabric.
Preliminar y Mesh Topology SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Multi-Chassis Fabrics 5-11 Mesh Zoning Sanbox Switch chassis support fabric-wide zones for all zone types. Broadcast Zones and Name Server Zones require no special consideration in a mesh fabric.
Preliminar y Multistage Topology SANbox-16HA Fibre Channel Switch 5-12 Multi-Chassis Fabrics 59005-03 Rev . A Installer’ s/User’ s Manual Multistage T opology A Multistage Switch consists of chassis configured in tw o dif ferent Stage T ypes, an Input-Output/T ransfer (IO/T) stage type, and a Cross-Connect (CC) Stage T ype.
Preliminar y Multistage Topology SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Multi-Chassis Fabrics 5-13 Multistage Bandwidth Multistage topolo gy has the best bandwidth.
Preliminar y Multistage Topology SANbox-16HA Fibre Channel Switch 5-14 Multi-Chassis Fabrics 59005-03 Rev . A Installer’ s/User’ s Manual Multistage Examples Figures 5-3 through 5-5 are e xamples of Multistage topolo gy using SANbox-16 Switch chassis.
Preliminar y Multistage Topology SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Multi-Chassis Fabrics 5-15 Figure 5-4 SANbox-16 Multistage with two T_Port links from each IO/T chassis Figure 5-4 sho ws a Multistage Switch built from SANbo x-16 chassis.
Preliminar y Multistage Topology SANbox-16HA Fibre Channel Switch 5-16 Multi-Chassis Fabrics 59005-03 Rev . A Installer’ s/User’ s Manual Figure 5-5 SANbox-16 Multistage with eight CC chassis Figure 5-5 sho ws a Multistage Switch built from SANbo x-16 chassis.
Preliminar y Cabling SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Multi-Chassis Fabrics 5-17 its user ports. In this case there is a T_P or t for each user port. If a T_P or t or CC chassis fails, the chassis re-assigns the user por t from the failed path to another T_P or t/CC that is good.
Preliminar y Chassis Configuration SANbox-16HA Fibre Channel Switch 5-18 Multi-Chassis Fabrics 59005-03 Rev . A Installer’ s/User’ s Manual Chassis Confi guration There are tw o parameters that control the role that each chassis plays in a multi- chassis fabric: Stage T ype and Chassis Number .
Preliminar y Chassis Configuration Process SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Multi-Chassis Fabrics 5-19 Chassis Confi guration Process 1. Ph ysicall y Connect a Management Station directl y to the Ethernet por t of the chassis through which the fabric will be managed.
Preliminar y Chassis Configuration Process SANbox-16HA Fibre Channel Switch 5-20 Multi-Chassis Fabrics 59005-03 Rev . A Installer’ s/User’ s Manual c. The F abric T opology windo w will displa y all the Switch chassis in the fabric and sho w the T_P or t interconnections.
Preliminar y SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Reference Information A-1 Appendix A Reference Information Appendix A contains the specifications for the SANbox-16 F ibre Channel Switch. Refer to “Fibre Channel P orts” on page 1-17 for the location of all connections, switches, and components.
Preliminar y SANbox-16HA Fibre Channel Switch Specifications SANbox-16HA Fibre Channel Switch A-2 Reference Information 59005-03 Rev . A Installer’ s/User’ s Manual SANbox-16HA Fibre Channel Switch Specifi cations Switch Fibre Channel Protocols:.
Preliminar y SANbox-16HA Fibre Channel Switch Specifications SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Reference Information A-3 Media T ype: ........................................Industr y standard Gigabit Interface Con ver ter (GBIC).
Preliminar y SANbox-16HA Fibre Channel Switch Specifications SANbox-16HA Fibre Channel Switch A-4 Reference Information 59005-03 Rev . A Installer’ s/User’ s Manual Switch Maintainability Maintenance Strategy: .
Preliminar y SANbox-16HA Fibre Channel Switch Specifications SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Reference Information A-5 Switch Mechanical Chassis Dimensions: .......................... Refer to Figure A-1 and F igure A-2 .
Preliminar y SANbox-16HA Fibre Channel Switch Specifications SANbox-16HA Fibre Channel Switch A-6 Reference Information 59005-03 Rev . A Installer’ s/User’ s Manual Non-Operating Altitude: ....................0 to 15240m (0 to 50,000 feet) Non Operating V ibration:.
Preliminar y SANbox-16HA Fibre Channel Switch Specifications SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Reference Information A-7 Recei ver Sensiti vity: ..........................-16dBm a verage Distance: ......
Preliminar y SANbox-16HA Fibre Channel Switch Specifications SANbox-16HA Fibre Channel Switch A-8 Reference Information 59005-03 Rev . A Installer’ s/User’ s Manual Copper Intra-Enclosure GBIC (passive) Connector: .................................
Preliminar y SANbox-16HA Fibre Channel Switch Specifications SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Reference Information A-9 Figure A-1 SANbox-16HA Switch Front/Back Dimensions in Millimeters (Inches) 444.5 (17.
Preliminar y SANbox-16HA Fibre Channel Switch Specifications SANbox-16HA Fibre Channel Switch A-10 Reference Information 59005-03 Rev . A Installer’ s/User’ s Manual Figure A-2 SANbox-16HA Switch T op View Dimensions in Millimeters (Inches) 17.78 (.
Preliminar y SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A QLogic Customer Support B-1 Appendix B QLogic Customer Support This appendix describes the basic w arranty and customer suppor t. Customers who purchased directl y from QLogic ma y contact Customer Suppor t as described in this appendix.
Preliminar y Software Support SANbox-16HA Fibre Channel Switch B-2 QLogic Customer Support 59005-03 Rev . A Installer’ s/User’ s Manual Software Support QLo gic activ ely supports the cur rent softw are/fir mw are release and the prior release for 6 months follo wing the general av ailability date for the cur rent release.
Preliminar y SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Index 1 Index A AC power connector 1-22, 2-5 accessible parts 1-8 air flow 2-2, A-5 AL_P A - See Arbitrated Loop Physical Address.
Preliminar y Index SANbox-16HA Fibre Channel Switch 2 Index 59005-03 Rev . A Installer’ s/User’ s Manual E emissions standards A-6 enclosure types A-5 environmental specifications A-5 error code .
Preliminar y Index SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Index 3 Hung Flash Control Code 3-11 I IEC regulations 2-4 immunity A-6 in order delivery 5-4 Input.
Preliminar y Index SANbox-16HA Fibre Channel Switch 4 Index 59005-03 Rev . A Installer’ s/User’ s Manual power source loading A-5 power supply 4-6 operating voltage A-5 over temperature light 1-24.
Preliminar y Index SANbox-16HA Fibre Channel Switch Installer’ s/User’ s Manual 59005-03 Rev . A Index 5 private targets 1-8, 2-19 public initiator 1-6 public targets 1-8 topologies supported 1-6 .
SANbox-16HA Fibre Channel Switch Index 59005-03 Rev . A Installer’ s/User’ s Manual Notes.
Ein wichtiger Punkt beim Kauf des Geräts Q-Logic 16HA (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Q-Logic 16HA noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Q-Logic 16HA - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Q-Logic 16HA reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Q-Logic 16HA erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Q-Logic 16HA besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Q-Logic 16HA verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Q-Logic 16HA. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Q-Logic 16HA gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
