Benutzeranleitung / Produktwartung PFSY92080 des Produzenten ProForm
Zur Seite of 28
¨ USERÕS MANUAL Model No. PFSY92080 Serial No. The serial number is found in the location shown below . Write the serial number in the space above. CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manu- al for future reference.
2 Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Before Y ou Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 ASSEMBLED DIMENSIONS: Height: 79 in. Width: 38 in. Length: 91 in. Low Pulley Station Foot Plate Leg Lever Butterfly Arms Press Arm Shroud Covering Weight Stack Seat Backrest Thank you for selecting the versatile PROFORM ¨ 920 Home Gym System.
4 Note: This introduction will save you more time than it takes to read it! Identifying Parts T o help you identify the small parts used in assem- bly , we have included a P ART IDENTIFICA TION CHART located in the center of this manual.
1. Before beginning, make sure that you have read and understood the information on page 4. Locate and open the parts bag labeled ÒFRAME ASSEMBL Y . Ó Press a 2Ó Square Inner Cap (24) into each end of the Stabilizer (5). Insert two 3/8Ó x 2 3/4Ó Carriage Bolts (20) up through the holes in the Stabilizer and place it flat on the floor .
5. Slide the Press Upright (3) onto the indicated 5/16Ó x 2 1/2Ó Carriage Bolts (22) in the Press Base (4). T ighten a 5/16Ó Nylon Locknut (68) onto each Carriage Bolt. Note: The Press Upright (3) must be leaning towards the center of the unit with the two brackets oriented as shown.
7. Position two W eight Bumpers (19) over the indicated holes in the Stabilizer (5). Insert both Weight Guides (23) through the Weight Bumpers (19) and the holes in the Stabilizer (5 ). See the inset drawing. Press two Round Weight Inserts (76) into the indicated holes in each Weight (26).
8 13. Press Arm AssemblyÑLocate and open the parts bag labeled ÒARM ASSEMBL Y .Ó Press a 2Ó Square Inner Cap (24) into the top of each arm on the Press Frame (12). Lubricate the 1/2Ó x 9 1/2Ó Bolt (59). Slide the Cable Frame (57) in between the arms of the Press Frame (12).
9 16. Butterfly Arm Assembly Press a 2Ó Square Inner Cap (24) into both ends of each Butterfly Arm (80 and 81). Wet the lower end of each Arm with soapy water . Slide a Butterfly Foam Pad (82) onto the lower end of each Arm. 16 14. Press a 2Ó Square Inner Cap (24) into the lower end of each Press Arm (46 and 47).
17 17. Lubricate both axles on the T op Frame (1). Identify the Right Arm (80) and the Left Arm (81) by noting the position of the welded bracket (A) on each Arm. Arm identification is very important for this step. Place a Weld Cover (63) on top of the Right Butterfly Arm (80) in the location shown.
11 22. Remove the 3/8Ó Nylon Jamnut (78) attached to the 3/8Ó x 5Ó Bolt (42) in step 20. Wrap the High Cable (73) around a 3 1/2Ó Pulley (35) in the direction shown. Slide the 3 1/2Ó Pulley (35) and a Cable T rap (44) onto the 3/8Ó x 5Ó Bolt (42) that was inserted into the welded tube on the Cable Frame (57) in step 20.
12 25. Wrap the High Cable (73) around a 3 1/2Ó Pulley (35) in the direction shown. Attach the 3 1/2Ó Pulley (35) to the bracket on the T op Frame (1) with a 3/8Ó x 2Ó Bolt (62) and a 3/8Ó Nylon Locknut (50). 25 1 62 73 50 Bracket 35 26. Thread the bolt at the end of the High Cable (73) a couple of turns into the top of the Weight Tube (77).
13 28. Dis-assemble the second set of Pulley Plates (31). Wrap the Butterfly Cable (97) around one of the 3 1/2Ó Pulleys (35) in the direction shown. Attach the 3 1/2Ó Pulley (35) and a Cable T rap (44) to the Pulley Plates (31) with a 3/8Ó x 2Ó Bolt (62) and a 3/8Ó Nylon Locknut (50).
14 32. Wrap the Low Cable (72) around a 3 1/2Ó Pulley (35) in the direction shown. Attach the Pulley (35) and a Cable T rap (44) to the lowest of the two holes in the Pulley Plates (31) hang- ing from the High Cable (73). Secure the Pulley and Cable T rap with a 3/8Ó x 2Ó Bolt (62) and a 3/8Ó Nylon Locknut (50).
15 36. Important: Follow all three Cables from end to end and make sure they rest in the grooves of all Pulleys and that both the Cables and the Pulleys move smoothly . Unscrew the cable bolt at the end of the High Cable (73) from the Weight Tube (77).
16 38. Attach one Backrest (41) to the Butterfly Backrest Frame (15) with two 1/4Ó x 3/4Ó Screws (17). Unscrew the handle on the Adjustment Knob (99) until it is loose. Pull out the handle as far as it will go and slide the Butterfly Backrest Frame (15) into the slot in the Butterfly Upright (2).
17 41. Press two 3/4Ó Round Inner Caps (34) into each Pad T ube (28). Insert one Pad T ube (28) into the Butterfly Seat Frame (1 1). Slide a Foam Roller (30) onto each end of the Pad T ube. Insert the other Pad T ube (28) into the Leg Lever (29). Slide a Foam Roller (30) onto each end of the Pad T ube.
18 44 44. The decal shown below has been attached to the home gym system in the two locations shown. If a decal is missing or illegible, please call our customer hotline at the number on the front cover to order a replacement decal. Apply the new decal in the appropriate location.
19 Cable Diagram The Cable Diagrams below show the proper routing of the Butterfly Cable (97), the High Cable (73) and the Low Cable (72). The numbers show the correct route for each cable. Make sure the Cables are routed correctly , that the Pulleys move smoothly and that the Cable T raps do not touch or bind the Cables.
20 Attaching the Lat Bar or Row Bar to the High Pulley Station Attach the Lat Bar (61) to the High Cable (73) with a Cable Clip (69). For some exercises, the Chain (67) should be attached between the Lat Bar and the High Cable with two Cable Clips.
Adjusting the Position of the Press Backrest for Row Exercises Unscrew the handle on the Adjustment Knob (99) until it is loose. Pull out the handle as far as it will go and tilt the Press Backrest (41) in or out to the desired position.
22 Arm Press Lower Pulley Upper Butterfly Weight Row Leg Ext. Pulley Arms Plates (lbs.) (lbs.) (lbs.) (lbs.) To p 13 7 12 6 1 29 19 21 18 2 43 30 32 32 3 57 42 45 44 4 74 52 58 56 5 87 64 68 70 6 106 .
Ordering Replacement Parts Limited W arranty T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1.
23 Additional slack can be removed by moving one or both of the 3 1/2Ó Pulleys (35) attached to one or both sets of Pulley Plates (31). T o move one Pulley , unscrew the 3/8Ó Nylon Locknut (50) and the 3/8Ó x 2Ó Bolt (62). Remove the Cable T rap (44) and Pulley (35) from the Pulley Plates (31).
1 3/4Ó Square Inner Cap (21) 3/4" Round Inner Cap (34) 3/4Ó Retaining Ring (86) 1" Round Inner Cap (88) 5/8Ó x 1/2Ó Bushing (32) 3/4Ó Dome Cap (75)Ñ2 2" Square Inner Cap (24) 1&qu.
3/8" Nylon Locknut (50) 3/8" Nylon Jam Nut (78) 5/16" Nylon Jamnut (25) 5/16" x 2 1/2" Bolt (45) 5/16" Nylon Locknut (68) #8 x 1Ó Black Screw (7) 1/4" x 1 3/4".
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. 1 1 T op Frame 2 1 Butterfly Upright 3 1 Press Upright 4 1 Press Base 5 1 Stabilizer 6 1 Leg Lever Bu.
32 32 78 55 74 55 68 45 17 6 7 17 11 29 13 41 15 17 17 2 68 68 22 22 68 68 8 24 68 68 50 18 3 38 24 22 22 4 78 55 54 55 35 47 46 1 18 50 50 24 24 42 35 35 50 85 79 50 62 35 31 35 50 62 44 62 48 35 68 .
Ein wichtiger Punkt beim Kauf des Geräts ProForm PFSY92080 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie ProForm PFSY92080 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für ProForm PFSY92080 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von ProForm PFSY92080 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über ProForm PFSY92080 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon ProForm PFSY92080 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von ProForm PFSY92080 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit ProForm PFSY92080. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei ProForm PFSY92080 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
