Benutzeranleitung / Produktwartung CD7200 des Produzenten Profile
Zur Seite of 20
CD7200 INSTALLATION INSTRUCTIONS / OWNER S MANUAL , AM/FM HIGH POWER DETACHABLE FACE CD PLAYER.
1 I NTRODUCTION Congratulations on your purchase of a Profile state-of-the-art single disc CD player. Your selection of a Profile car audio product indicates a true appreciation of fine musical reproduction.
2 S AFETY PRECAUTIONS Secure the CD player When installing your CD player in the vehicle, make sure it is mounted properly in the dash, using an after market installation kit if needed. When using the supplied mounting sleeve, it is a must that you also use the supplied back brace to support the back of the CD player.
3 C ARE AND MAINTENANCE Cleaning the CD player When cleaning the vehicle, be sure not to get any water in or on the CD player. Clean only the exterior surface of the unit with a dry, clean soft towel using no chemical solvents. Operating in extreme temperatures Sometimes the unit will not operate in extreme, hot or cold temperatures.
4 DISC CARE AND PLAY: Before playing, clean the disc with a clean, lint-free cloth. Wipe the disc in the direction of the arrow. Do not use solvents such as benzine or thinners. Commercially available cleaners or anti static spray will damage the unit.
5 E LECTRICAL AND SIGNAL CONNECTIONS FOUR SPEAKER SYSTEM Before making the following connections, take time to look over the vehicle s wiring and determine the location and wires you will be connecting to.
6 CAUTION! Tape unused wires so they do not short against other wires or chassis ground. TWO SPEAKER SYSTEM CD7200 NOT USED NOT USED NOT USED NOT USED + + + + YELLOW ANTENNA CONNECTOR MEMORY +12V BLAC.
7 M OUNTING THE CD PLAYER There are two different ways to mount the CD Player. In most Japanese vehicles you can use the factory mounting brackets, taking advantage of the ISO/DIN opening. If your vehicle does not have ISO/DIN opening, you can mount the CD Player using the supplied DIN sleeve and rear support bracket.
8 Attach the back brace to the CD player using the supplied hardware. Then attach the other end of the brace to a firm mounting surface (i.e. Dash brace, fire wall, e.t.c.) This will brace the back of the CD player to ensure solid mounting to prevent theft and provide optimal CD play.
9 ISO/DIN MOUNTING If you own a Japanese vehicle, you can use the standard ISO/DIN mounting screw holes on the side of the CD player to attach to the existing factory mounting bracket, without using the provided DIN sleeve. Remove the factory ISO/DIN mounting bracket from the car along with the factory radio.
10 CD7200 LOCATION AND FUNCTION OF CONTROLS.
11 1 POWER To t u r n O N t h e unit, press any button except the EJT and OPEN button. To t u r n O F F t h e unit, press the PWR button. 2 DETACH PANEL Press the OPEN button to detach the front panel. This will allow you to remove the front panel. 3 CD PLAY To play a CD, gently insert the CD into the slot with the label side facing up.
12 9 10 RADIO TUNE & CD TRACK UP/DOWN, CD FAST FORWARD/REWIND Under radio mode, press the UP 9 or DN 10 button momentarily and repeatedly to change the frequency number up or down one step. Press and hold the button for more than 1 second to seek to the next clear station.
13 DSP - The unit is equipped with 4 preset equalization modes. Press the SEL button for more than 1 second to display DSP OFF. Then use V.UP 5 and V.DN 6 buttons to choose one of 4 following preset EQ s in the following order. In DSP OFF mode, the EQ is controlled by Bass and Treble settings.
14 16 RANDOM PLAY In CD play mode, press the RDM 16 button to play all tracks of the disc in random sequence. Press it again to cancel random play. 17 RADIO SCAN In radio mode, press the SCN 17 button to scan up one strong radio station signal at a time.
15 T ROUBLE SHOOTING THE SYSTEM The following chart will help in solving most problems that ma y occur. Should any problem persist after you have made these checks, please consult yo ur nearest Profile retailer. Before going through this check list, refer back to the wiring a nd operating procedures.
SYMPTOM CAUSE SOLUTION The installation angle is greater than 30 degrees Adjust the angle of the unit to l ess than 30 degrees The disc player is installed incorrectly Check to see if the unit is fastened securely with the back brace supporting the rear of the unit.
S PECIFICATIONS GENERAL Power Supply Requirements...........................................DC 12 Volts, Negative Ground Chassis Dimensions ....................................................................7(W) x 6 1/2 (D) x 2 (H) Tone Controls.....
LIMITED WARRANTY Profile Consumer Electronics, Inc. warrants this product to be free from defects in material and workmanship for a period of One (1) Year from the date of sale to the original consumer purchaser.
PROFILE CONSUMER ELECTRONICS, INC. 15060 SHOEMAKER AVE SANTA FE SPRINGS, CA 90670 TEL: (562)404-9393 FAX: (562)404-9433 WWW.PROFILEUSA.COM WARRANTY REPAIR POLICY In the unlikely event of product failure, the following procedures should be followed 1) The unit must be under the 1-year warranty period.
Ein wichtiger Punkt beim Kauf des Geräts Profile CD7200 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Profile CD7200 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Profile CD7200 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Profile CD7200 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Profile CD7200 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Profile CD7200 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Profile CD7200 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Profile CD7200. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Profile CD7200 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
