Benutzeranleitung / Produktwartung PDGT26H48B des Produzenten Poulan Pro
Zur Seite of 48
IMPORTANT MANUAL Do Not Throw Away Poulan 00993-poulan_pro I OWNER'S MANUAL MODEL: PDGT26H48B LAWN TRACTOR WARNING: Read the Owner's Manual and fol- low all Warnings and Safety Instruc- tions. Failure to do so can result in serious injury. Always Wear Eye Protection During Operation 186714 Rev.
SAFETY RULES SAFE OFERAT,ON PRACT,CES FOR .,DE-ON .OVERS a IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATINGHANDS AND FEET AND THROWING OBJECTS.
SAFETY RULES • Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. • Never carry passengers or children even with the blades off. Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing.
PRODUCT SPECIFICATIONS GasolineCapacity 5.0 Gallons and type: Unleaded Regular Oil Type (API-SF-SJ): SAE 30 (above,32°F) SAE 5W-30 (below 32°1=) Oil Capacity: W/Filter: 4.0 Pints W/O Filter: 3.75 Pints Spark Plug: Champion QC12YC 3ap: .040") Ground Speed (MPH): Forward: 5.
UNASSEMBLED PARTS Steering Wheel Steering Sleeve Steering Sleeve Extension © Premium Steering Adapter Steering Wheel Insert Seat (1) Washer (_) 17/32 x 1-3/16 x 12 Gauge (1) Knob I_ Nose Roller _RNos.
ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
ASSEMBLY INSTALL SEAT (See Fig. 3) Adjust seat before tightening adjustment knob. • Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. Pivot seat upward and remove from the cardboard pack- ing.
ASSEMBLY TO ATrACH NOSE ROLLER (See Fig. 5) • Assemble brackets "A" and "B" to the inside of mower mounting brackets as shown. Tighten securely. NOTE: Be sure bracket tabs are positioned in tab holes in mower brackets. • Position nose roller between brackets and install rod and retainer spring.
ASSEMBLY CHECKTIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown in "PRODUCT SPECIFICATIONS" section of this manual.
OPERATION These symbols may appear on your tractor or in literature supplied with the product, Learn and understand their mean- ing. R N H L I'-,I REVERSE NEUTRAL HIGH LOW CHOKE FAST SLOW IGNITIO.
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR. Compare the illustrations wtth your tractor to famtlianze yourself with the Iocahon of various controls and adjustments.
T OPERATION HOW TO USE YOUR TRACTOR TO SET PARKING BRAKE (See Fig. 8) Your tractor is equipped with an operator presence sens- ing switch. When engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine.
OPERATION TO ADJUST GAUGE WHEELS (See Fig. 9) Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.
OPERATION FIG. 11 TOWING CARTS AND OTHER ATTACH- MENTS Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor. Use common sense when towing.Too heavy of a load, while on a slope, is dangerous.
OPERATION • Remove retainer sprmg from the drive belt tenston handle to relieve belt tension. • Start engme and allow _t to warm up for three (3) min- utes • Shut-off engine and engage parking brake • Engage dnve belt tension handle and replace the retainer spring.
MAINTENANCE FELL IN OATES REGU R SERV,CE S V,CE" DATES Check Brake Operation Check Tire Pressure _ Check Operator Presence and T Interlock Systems R Check for Loose Fasteners _ I_s If A Sharpen/R.
MAINTENANCE MANDREL ASSEMBLY TRACTOR Always observe safety rules when performing any main- tenance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highestgear, then brake must be adjusted. (See "TO ADJUST BRAKE"in the Service and Adjustments section of this manual).
MAINTENANCE TO CLEAN BATI'ERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to "leak" power. • Remove terminal guard. • Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.
MAINTENANCE CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers.
SERVICE AND ADJUSTMENTS WARNING:TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: Depress brake pedal fully and set parking brake. Place attachment clutch in "DISENGAGED" position. • Turn ignition key to "STOP" and remove key.
SERVICE AND ADJUSTMENTS NOTE: To assist in locating hole in flanged pin, the hole in pin is inline with notch on head of pin. If necessary, move mower side-to-side to give space between plate and mower brackets. IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.
SERVICE AND ADJUSTMENTS f BOTH FRONT PLATE LINKS MUST BE EQUAL IN LENGTH NUT "D"_ FRONT PLATE !. ] "/ ASSEMBLY _ NUT"C" _ TRUNNION FIG. 23 TO REPLACE MOWER DRIVE BELT MOWER DRIVE BELT REMOVAL (See Fig. 24) • Park tractor on a level surface.
SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE (SECONDARY) DRIVE BELT (See Fig. 25) Park the tractor on level surface. Engage parking brake. Remove mower (See "TO REMOVE MOWER" in this section of manual). • Remove screws from R.H. and L.H.
SERVICE AND ADJUSTMENTS TO CHECK AND ADJUST BRAKE If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.
SERVICE AND ADJUSTMENTS TO REMOVE WHEEL FOR REPAIRS FRONT WHEEL (See Fig. 29) • Block up axle securely. • Remove axle cover, retaining ring and washers to allow wheel removal. Repair tire and reassemble. • Replace washers and snap retaining ring securely in axle groove.
SERVICE AND ADJUSTMENTS TERMINAL KEPS NUT ACCESS DOOR .. -,-.. i HEX BOLT POSITIVE CABLE TERMINAL GUARD NEGATIVE (SLACK) CABLE FIG. 31 TO REPLACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.
SERVICE AND ADJUSTMENTS ENGINE TO ADJUST THROTTLE CONTROL CABLE (See Fig. 33) The throttle control has been preset at the factory and adjustment should not be necessary.
STORAGE ENGINE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. A WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
TROUBLESHOOTING POINTS PROBLEM Will not start Hard to start Engine will not turn over Engine clicks but will not start Loss of power Excessive vibration CAUSE 1. Out of fuel. 2. Engine not =CHOKED" properly. 3. Engine flooded. 4. Bad spark plug. 5.
TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Engine continues to run when operator leaves seat with attachment clutch engaged Poor cut - uneven Mower blades will net rotate Poor grass discharge Ileedllght(e) not working (if so equipped) Battery will not charge Loss of drive Engine "bad(fires" when turning engine =OFF" 1.
TRACTOR - MODEL NUMBER PDGT26H48B; PRODUCT NUMBER 954 56 95-30 SCHEMATIC _'i" CH_ RGING SYSTEM 16 AMp OC @ 3600 RPM _r eye project. IGNITION SWITCH POSI_ON CIRCUIT "MAKE" RELAY OFF.
REPAIR PARTS TRACTOR - MODEL NUMBER PDGT26H48B, PRODUCT NUMBER 954 56 95-30 ELECTRICAL 41 8 81 29 I J 33 3O I I I I 32.
REPAIR PARTS TRACTOR - MODEL NUMBER PDGT26H48B, PRODUCT NUMBER 954 56 95-30 ELECTRICAL KEY PART NO. NO. DESCRIPTION 1 144927 Battery 2 74760412 Bolt Hex Head 1/4-20 x 3/4 8 7603J Tray, Battery 10 145211 Bolt Btr Frt 1/4-20 x 7.
REPAIR PARTS " TRACTOR - MODEL NUMBER PDGT26H48B, PRODUCT NUMBER 954 56 95-30 CHASSIS AND ENCLOSURES 21 47 58 28 161 ;11 = '_l i !_2 o 19 158 37 86 17 138 56 99 34.
REPAIR PARTS ......... TRACTOR - MODEL NUMBER PDGT26H48B, PRODUCT NUMBER 954 56 95-30 CHASSIS AND ENCLOSURES KEY PART KEY PART NO. NO. DESCRIPTION NO. NO.
REPAIR PARTS .... TRACTOR - MODEL NUMBER PDGT26H48B, PRODUCT NUMBER 954 56 95-30 GROUND DRIVE 9 69 drive_6-vgt 127 120 122, 42 6 38 37 46 128 06 07 108 112 36.
REPAIR PARTS TRACTOR "- MODEL NUMBER PDGT26H48B, PRODUCT NUMBER 954 56 95-30 GROUND DRIVE KEY PART KEY NO. NO. DESCRIPTION NO. 1 ....... Transaxle Hydro Gear 77 74780716 331-3000 (Order Parts From Trans- 89 73680700 axle Manufacturer) 94 133835 2 7070E Key Sq.
REPAIR PARTS TRACTOR - MODEL NUMBER PDGT26H48B, PRODUCT NUMBER 954 56 95-30 STEERING ASSEMBLY 23 ,.. _3 34 32 6 27 42 22 .31 14 19 ' ' j 18 '_"'-,_st eedng_ 10-_t 28 47 15.
REPAIR PARTS TRACTOR - MODEL NUMBER PDGT26H48B, PRODUCT NUMBER 954 56 95-30 STEERING ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 180656 2 178557 3 6855M 4 161849 5 161848 6 6266H 7 121748X 8 12000029 9 12.
REPAIR PARTS TRACTOR - MODEL NUMBER PDGT26H48B, PRODUCT NUMBER 954 56 95-30 ENGINE 18 15 37 26 "37 39 KEY PART NO. NO. DESCRIPTION 84 B4 _/74 I 81 KEY NO.
REPAIR PARTS TRACTOR - MODEL NUMBER PDGT26H48B, PRODUCT NUMBER 954 56 95-30 LIFT ASSEMBLY 40 43 35 73 31 8 t0 10 / 2 6 7O 23 7O KEY NO. 1 2 3 4 5 6 7 8 10 11 12 23 24 26 29 30 31 32 33 PART NO.
REPAIR PARTS TRACTOR - MODEL NUMBER PDGT26H48B, PRODUCT NUMBER 954 56 95-30 'SEAT ASSEMBLY _KEY NO, 1 2 4 5 ,6 7 8 10 12 13 14 75 PART NO. 171684 140551 127018X 145006 73800600 124181X 171877 182493 121246X 121248X 72050412 121249X DESCRIPTION Seat Bracket, Pivot Seat Bolt, Shoulder 5/16-18 x .
REPAIR PARTS TRACTOR - MODEL NUMBER PDGT26H48B, PRODUCT NUMBER 954 56 95-30 DECALS 9 15 3 5 5 4 10 7 29 2 2 14 6 ...... , 17 KEY PART KEY NO. NO. DESCRIPTION NO, 1 164097 Decal, Dash 13 2 184858 Deca.
REPAIR PARTS • + TRACTOR - MODEL NUMBER PDGT26H48B, PRODUCT NUMBER 954 56 95-30 MOWER DECK 46 132 95 112 i 5 121 33 _30 114 21 110 '1 I,! 46 45 I I 47 mower_dec_.
REPAIR PARTS TRACTOR ; MODEL NUMBER PDGT26H48B, PRODUCT NUMBER954 56 95-30 MOWER DECK KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 3 5 6 8 11 13 14 15 16 17 18 19 20 21 24 25 26 27 28 2.
LIMITED WARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materi- als and workmanship.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION 15 DEGREES MAX. _t ARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control.
PARTS AND SERVICE Your POULAN PRO product has been expertly engineered and carefully manufactured to rigid quality standards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit. FOR SERVICE OR REPLACEMENT PARTS: 1.
Ein wichtiger Punkt beim Kauf des Geräts Poulan Pro PDGT26H48B (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Poulan Pro PDGT26H48B noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Poulan Pro PDGT26H48B - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Poulan Pro PDGT26H48B reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Poulan Pro PDGT26H48B erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Poulan Pro PDGT26H48B besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Poulan Pro PDGT26H48B verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Poulan Pro PDGT26H48B. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Poulan Pro PDGT26H48B gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
