Benutzeranleitung / Produktwartung 271490 des Produzenten Poulan Pro
Zur Seite of 48
OWNER'S MANUAL MODELNO. 271490 14.5 HP 38 INCH LAWNTRACTOR • Assembly • Operation Maintenance • Service and Adjustments • Troubleshooting • Repair Parts For Parts and Service, contact our authorized distributor: call 1-800-849-1297 For Technical Assistance: call 1-800-829-5886 181203 12.
Safety Rules ......................................... 2 Product Specifications .......................... 5 Assembly/Pre-Operation ...................... 7 Operation ............................................ 10 Maintenance Schedule ...............
• Do not mow near drop-offs, ditches, or embankments. The mower could suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in. • Do not mow on wet grass. Reduced traction could cause sliding. • Do not try to stabilize the machine by putting your foot on the ground.
• Avoid starting or stopping on a slope, if tires lose traction, disengage the blades and proceed slowly straight down the slope. • If machine stops while going uphill, disengage blades, shift into reverse and back down slowly. • Do not turn on slopes unless neces- sary, and then, turn slowly and gradu- ally downhill, if possible.
PRODUCT SPECIFICATIONS Gasoline 1.25 Capacity and Unleaded and Type: Regular Oil Type SAE 30 (above 32°F) (API-SF-SJ): SAE 5W-30 (below 32°F) Oil Capacity: 3 Pints Spark Plug: Champion RJ19LM (Gap: .030") Ground Speed (MPH): Forward: 1st 1.1 2nd 1.
Steering Wheel Insert (1) Hex Bolt 5/16-18 x 1-1/4 ,_ Steering Wheel Adapter (1) Large Flat Washer (1) Locknut 5/16-1= _1_ _ (1) Lockwasher 3/8 Steering Boot Steering Extension Shaft O I Seat (1) Wash.
Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
Seat Terminal INSTALL SEAT Adjust seat before tightening adjustment knob. 1. Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. 2. Pivot seat upward and remove from the cardboard packing.
CHECK TIRE PRESSURE The tires on your tractor were overin- flated at the factory for shipping pur- poses. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown in "PRODUCT SPECIFICATIONS" section of this manual.
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. BA'FFERY CAUTION OR REVERSE FORWARD FAST SLOW WARNING J ENGINE ON ENGINE O.
KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.
tip withthe engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed. • The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months.
ADD GASOLINE • Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline.
MOWING TIPS • Tire chains cannot be used when the mower housing is attached to tractor. • Mower should be properly leveled for best mowing performance. See "3"0 LEVEL MOWER HOUSING in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trimming.
MAINTENANCE SCHEDULE _ ,_,_ _ ,_'=_ _ FILL IN DATES AS YOU COMPLETE REGULAR SERVICE Check Brake Operation Check Tire Pressure Check Operator Presence and T Interlock Systems R Check for Loose Fas.
TRACTOR Always observe safety rules when performing any maintenance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be ad- justed. (See "TO ADJUST BRAKE" in the Service and Adjustments section of this manual).
• Keep small vent holes open. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.
Service air cleaner more often under dusty conditions. 1. Remove knob(s) and cover. TO SERVICE PRE-CLEANER 2. Slide foam pre-cleaner off cartridge. 3. Wash it in liquid detergent and water. 4. Squeeze it dry in a clean cloth. 5. Saturate it in engine oil.
[,_ ARNING: TO AVIOD SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: 1. Depress clutch/brake pedal fully and set parking brake. 2. Place gearshift lever in neutral (N) position. 3. Place attachment clutch in "DISENGAGED" position, 4.
TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PROD- UCT SPECiFiCATIONS" section of this manual). If tires are over or underinflated, you will not properly adjust your mower.
3. Roll belt off engine pulley. 4. Disconnect R.H. suspension arm from rear deck bracket by removing retainer spring. 5. Work belt off both mandrel pulleys and idler pulleys. 6. Pull belt away from mower. BELT INSTALLATION - 1. Work new belt around both mandrel pulleys and idler pulleys.
TO ADJUST STEERING WHEEL ALIGN- MENT If steering wheel crossbars are not horizontal (left to dght) when wheels are positioned straight forward, remove steering wheel and reassemble with crossbars horizontal. Tighten securely. FRONT WHEEL TOE-IN/CAMBER The front wheel toe-in and camber are not adjustable on your tractor.
Terminal Nut Hex Bolt Positive (Red) Cable Negative (Black) Cable TO REPLACE HEADLIGHT BULB 1. Raise hood. 2. Pull bulb holder out of the hole in the backside of the grill. 3. Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.
Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. _1_ CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
TROUBLESHOOTING CHART PROBLEM Will not start Hard to start Enginewill not turn over Engine clicks but will not start CAUSE • Out of fuel. • Engine not"CHOKED" properly. • Engine flooded. • Bad spark plug. • Dirty air filter. • Dirty fuel filter.
TROUBLESHOOTING CHART PROBLEM CAUSE CORRECTION Loss of power • Cutting too much grass/too fast. • Throttle in "CHOKE" position. • Build-up of grass, leaves and trash under mower. • Dirty air filter. • Low oil leveVdirty oil. • Faulty spark plug.
TROUBLESHOOTING CHART PROBLEM Mower blades will not rotate Poor grass discharge CAUSE • Obstruction in clutch mechanism. • Worn/damaged mower drive belt. • Frozen idler pulley. • Frozen blade mandrel. • Engine speed too slow. • Travel speed too fast.
TRACTOR - MODEL NUMBER 271490 SCHEMATIC /; _)AMMETER IGNmON SWITCH REO _D BATTERY FUSE :©: ,O-: _LUTCHJB_K_ (PEDAL UP) BLACK B_ STARTER ...... I D SEAT SWITCH .
TRACTOR - MODEL NUMBER 271490 ELECTRICAL 22 26 I I i ,, I I I I I I I I I I f-, .... J*l_t I II I II I I i I I I I I / / / / / 30.
TRACTOR - MODEL NUMBER 271490 ELECTRICAL KEY PART NO. NO. DESCRIPTION 1 163465 Battery 2 74760412 Bolt, Hex Head 1/4-20 unc x 3/4 8 176689 BoX Battery Fender 16 176138 Switch, Interlock 21 175685 Harn.
TRACTOR - MODEL NUMBER 271490 CHASSIS AND ENCLOSURES 3O 29 26 31_ 2O8 26 2O9 58 12 28 53 54 26 33 206 lO 26 13 o' _ 2O8.
TRACTOR - MODEL NUMBER 271490 CHASSIS AND ENCLOSURES KEY PART NO. NO. DESCRIPTION 1 174620 Chassis 2 176554 Drewbar 3 17060612 Screw 3/8-16 x 3/4 5 155272 Bumper Hood/Dash 6 174643X014 Saddle Slkser F.
TRACTOR - MODEL NUMBER 271490 GROUND DRIVE 12 34 34.
TRACTOR - MODEL N UM BER 271490 GROUND DRIVE KEY PART NO. NO. 1 ...... 2 146682 3 123666X 4 12000028 5 121520X 6 17060512 7 162240 8 131679 10 76020416 11 105701X 12 19151215 13 74550412 14 10040400 1.
TRACTOR - MODEL NUMBER 271490 STEERING / /" 1 t ..... s "2½"' I r i ,_----..__,_ / 29 H I 46 e_ 68 67 67 2_ ,o _ '_ _ _ .
TRACTOR - MODEL NUMBER 271490 STEERING KEY PART NO. NO, DESCRIPTION 1 140044X428 SteeringWheel 2 175131 Axle Assembly 3 169840 Spindle Assembly, L.H, 4 169839 Spindle Assembly, R.
TRACTOR - MODEL NUMBER 271490 ENGINE OPTIONAL EQUIPMENT Spark Arrester 38.
TRACTOR - MODEL NUMBER 271490 ENGINE KEY PART NO. NO, DESCRIPTION 1 2 3 170551 17720408 4 137352 13 165291 14 13280324 15 13200300 16 11050600 23 169837 29 137180 31 1(73202X 32 140527 33 123487X 37 137040 38 .
TRACTOR - MODEL NUMBER 271490 SEAT ASSEMBLY 25 KEY PART NO. NO. DESCRIPTION 1 127427 Seat 2 140551 Bracket Pvt St 3 71110616 Bolt Fin Hex 3/8-16unc x 1 4 19131610 Washer Flat 13/32 xl xl0 Ga 5 145006 .
TRACTOR - MODEL NUMBER 271490 DECALS 4 3 7 2_ 15 © 13 KEY PART NO. NO. 1 177097 2 176396 3 171828 4 171829 5 145005 7 171830 8 156867 11 156439 12 DESCRIPTION Decal Lower Dash Decal Engine Decal Hood Decal Fender Decal Battery Danger Decal Steering Decal, Oper sdl P/L Gear Decal Fender Dnger KEY PART NO.
TRACTOR - MODEL N UMBER 271490 LIFT ASSEMBLY 7 5 3 13 2 4 6 ,8 i, I' / i' .I' I' ,I 6 5 13 19 13 19 2O 15 2O 42.
TRACTOR- MODEL NUMBER 271490 LIFT ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 159460 Wire Asm Inner W/plunger 2 159471 Shaft Asm Uft 3 105767X Pin Groove 1 500 Zinc 4 12000002 E Ring #5133-62 5 19211621 W.
TRACTOR - MODEL NUMBER 271490 MOWER DECK 86 4 149 44.
TRACTOR - MODEL NUMBER 271490 MOWER DECK KEY PART NO. NO. 1 170280 2 72140506 3 138017 4 169970 5 4939M 6 178024 8 850857 9 10030600 10 140296 11 134148 13 137645 14 128774 15 110485X 16 174493 19 132.
LIMITED WARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and workmanship.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION 1. Fold this page along dotted line indicated above. 2. Hold page before you so that Its left edge is vertically parallel to a tree trunk or other upright structure, 3. Sight across the fold in the direction of hill slope you want to measure.
Poulan.
Ein wichtiger Punkt beim Kauf des Geräts Poulan Pro 271490 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Poulan Pro 271490 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Poulan Pro 271490 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Poulan Pro 271490 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Poulan Pro 271490 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Poulan Pro 271490 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Poulan Pro 271490 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Poulan Pro 271490. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Poulan Pro 271490 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
