Benutzeranleitung / Produktwartung PP2000 des Produzenten POSIFLEX Business Machines
Zur Seite of 30
Rev. A PP2000 Series 2 Station Printer User’s Guide.
Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
PP2000 (E) User’s Manual i Table of Contents PRODUCT BRIEFING . . . . . . . . . . . . . . . . . . . . . . 1 -- 1 MAIN PARTS ON THE EXTERIOR . . . . . . 2 -- 1 OUTPUT AREAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 -- 1 CONTROL PANEL .
PP2000 (E) User’s Manual ii STORE STAMP (OPTION) . . . . . . . . . . . . . . . . . . . . . . 6 -- 4 INTERNAL SWITCHES . . . . . . . . . . . . . . . . . . . . . . . . 6 -- 4 CASH DRAWER CONNECTOR . . . . . . . . . . . . . . . . . 6 -- 5 SERIAL INPUT CONNECTOR (STANDARD 9 PIN RS232 INTERFACE) .
PP2000 (E) User’s Manual 1 - 1 I. PRODUCT BRIEFING This is a high speed 2 - station journal / receipt printer. l A standard 2 station Journal / Receipt printer: The printing paper width is 44.5 mm. The printer can print both journal and receipt at the same time or only journal or receipt alone.
PP2000 (E) User’s Manual 1 - 2 l Options include auto stamping ability of the store stamp on receipt and auto cutting of the receipt. l The ability of cutting paper in full or in part by software on receipt .
PP2000 (E) User’s Manual 2 - 1 II. MAIN PARTS ON THE EXTERIOR A. OUTPUT AREAS B. CONTROL PANEL Receipt exit slot Journal window Validation printing insert slot Power LED On line LED Power On/Off swi.
PP2000 (E) User’s Manual 2 - 2 C. INPUT / OUTPUT CONNECTOR Cash drawer connector Serial connector Power connector Parallel connector.
PP2000 (E) User’s Manual 3 - 1 III. INS TALL ATION A. CHECK CONTENTS When you unpack carefully the carton that delivers PP2000 series printer, you will find it contains several items as illustrated below.
PP2000 (E) User’s Manual 3 - 2 C. STORE STAMP INSTALLATION If your printer comes with stamp option, you can find a store stamp case in the rear of the receipt part of print anvil assembly. You may take it out gently by holding its handle with your fingers.
PP2000 (E) User’s Manual 3 - 3 of store stamp. When the printing ink of the stamp is not enough , you can drip printing ink into the two holes in the rear of the stamp case. D. R IBBON INSTALLATION / REPLACEMENT When replacing the ribbon, please take the handle at the center of the old ribbon case and lift it up.
PP2000 (E) User’s Manual 3 - 4 turn the knob of the ribbon in the marked direction to tighten the ribbon and to ensure proper operation of the ribbon and to avoid jamming. E. CASH DRAWER CONNECTION Using the Posiflex signal cable CCBLA-180 to control a Posiflex cash drawer ( CR3100 or CR3200).
PP2000 (E) User’s Manual 3 - 5 H. POWER ON Turn on the On/Off switch at the left to the control panel, there will be a short buzzing sound and it indicate s a normal power on. I. PAPER ROLLS INSTALLATION 1. Please refer to the picture above: Put the receipt roll into the left paper roll compartment and the journal roll into the right.
PP2000 (E) User’s Manual 3 - 6 4. To give an idea about the positioning matter of the receipt, the print center is 33.3 mm behind the auto-cut position, whilst the stamp center is 40.
PP2000 (E) User’s Manual 4 - 1 IV. MAINTENANCE NOTICES l The printer should be put at a well ventilated site and avoid direct sunshine, also avoid high temperature, high humidity, high magnetic field. The site should also be free from lots of metal chips and dust.
.
PP2000 (E) User’s Manual 5 - 1 V. SOFT WA RE COMMANDS The commands supported by the PP2000 Printer are listed below. For detail description of the below listed commands, please visit our web site http://www.posiflex.com.tw for detail descriptions of each command.
PP2000 (E) User’s Manual 5 - 2 Software commands continued. NAME HEX FUNCTION ESC o 1B 6F Stamp ESC p 1B 70 Generate pulse ESC t 1B 74 Select character code table ESC u 1B 75 Transmit peripheral dev.
PP2000 (E) User’s Manual 6 - 1 VI. SPECIFIC ATIONS A. VALIDATION PRINTING Paper width: 140 mm or above Paper height: 65 mm or above Paper thickness: 0.07 ~ 0.14 mm Validation print: One line Number of characters: 55 Print area and sensor position: As illustrated in drawing above B.
PP2000 (E) User’s Manual 6 - 2 C. LED INDICATIONS Power LED: Green: Printer power is working On line LED: Green: Printer is at on line state. The printer takes command from the host system at this state and takes no command from the buttons. Receipt LED: Red: Receipt pa per is out, or malfunction with receipt print.
PP2000 (E) User’s Manual 6 - 3 E. PRINTER GENERAL SPEC ITEM SPECIFICATION Functions Receipt, journal and validation printing Printing Method 9 pin dot matrix impact; synchronized or separate printing of receipt and/or journal Printing Speed About 3 lines/sec.
PP2000 (E) User’s Manual 6 - 4 F. STORE STAMP (OPTION) Cushion width: 34.0 mm Cushion height: 24.0 mm Cushion thickness: 1.0 mm Cushion material: PE foam Stamp total width: 34.0 mm Stamp total height: 24.0 mm ( engraving included ) Stamp total thickness: 5.
PP2000 (E) User’s Manual 6 - 5 H. CASH DRAWER CONNECTOR PIN DEFINITION 1 Frame ground 2 CR2 kick (by Esc p 0 n1 n2) 3 Drawer open sense 4 +24 V DC power 5 CR1 kick (by Esc p 1 n1 n2) 6 Signal ground I. SERI AL INPUT CONNECTOR ( standard 9 pin RS232 interface) J.
PP2000 (E) User’s Manual 6 - 6 M. ENVIRONMENT Temperature: 0 ° C to 50 ° C Humidity: RH 10% to RH 90% without condensation N. RELI ABILITY Printer mechanism (without print head) life: 8,000,000 lines Print head life: 150,000,000 characters (2 dots/wire/character average) O.
PP2000 (E) User’s Manual 7 - 1 VII. REGULAR MAINTENANCE PROCEDURE A. DAILY MAINTENANCE Perform a basic cleaning and maintenance daily at a suitable timing as following 1. Turn power off and open the top cover. Press down the receipt lever and the journal lever.
PP2000 (E) User’s Manual 7 - 2 B. PERIODIC M AINTENANCE A periodic maintenance and lubrication should take place by a qualified maintenance specialist in every 6 months.
PP2000 (E) User’s Manual 8 - 1 VIII. BASIC TROUBLE SHOOTING A. NO OPERATION AFTER POWER ON If the printer does not work, neither does the power on LED lit: 1. Check if the power cord is well connected. 2. Check if the power outlet the printer is connected to is supplied with power.
PP2000 (E) User’s Manual 8 - 2 D. PAPER JAMMED In case of serious paper jammed problem, please pull both the receipt lever and the journal lever forward and push the print anvil assembly backward (as indicated in the picture) to raise the print anvil assembly.
PP2000 (E) User’s Manual 8 - 3 Once the print anvil assembly is lifted, the paper jam can be dismissed. Please clean the paper residue in the area before putting back the print anvil assembly if the condition requires. When you are putting back the print anvil, please pay special attention to the position of the pick up reel for journal.
PP2000 (E) User’s Manual 8 - 4 However, the journal pick up reel does not automatically move forward when the print anvil assembly is put back. Please then put the journal pick up reel back to its original location, and roll the reel so that the journal remains properly tensioned.
Ein wichtiger Punkt beim Kauf des Geräts POSIFLEX Business Machines PP2000 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie POSIFLEX Business Machines PP2000 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für POSIFLEX Business Machines PP2000 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von POSIFLEX Business Machines PP2000 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über POSIFLEX Business Machines PP2000 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon POSIFLEX Business Machines PP2000 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von POSIFLEX Business Machines PP2000 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit POSIFLEX Business Machines PP2000. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei POSIFLEX Business Machines PP2000 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
