Benutzeranleitung / Produktwartung 600 RMK Shift des Produzenten Polaris
Zur Seite of 133
.
.
WARNING Read, understand, and follow all of the in structions and safe ty precautions in this manual and on all produ ct labels. F ailure to follow the safety precautions could result in serious injury or dea th.
1 WELCOME Thank you for purchasin g a Polaris vehicle, and welcome to our world- wide family of Polaris owners. W e p roudly produce an exciting line of utility and recreati onal products.
2 POLARIS and POLARIS TH E W A Y OU T are regist ered trademarks of Pola ris Indus- tries Inc. Copyright 2008 Polaris Sales Inc. All inform ation contained within this publication is based on the latest product information at th e time of publication.
3 T ABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 This section contains helpful info rmation for own ers and drivers and illustrates the location of important identification numbers that should be recorded in the owner ’ s manual.
4.
5 INTRODUCTION Important Notes for Owners and Drivers After reading this manual, store it in the snowmobile for convenient ref- erence. It should remain with the snowmobile when th e snowmobile is sold. Some of the illustrations and photos used in this manual are general rep- resentations.
6 INTRODUCTION Preservation of the Environment Polaris is committed to supporting an environmental education cam- paign. W e encourage state and provin cial governments across the sn ow- belt to adopt rigorous safety traini ng programs that encourage protection of our environment, includ ing wildlife and vegetation.
7 INTRODUCTION V ehicle Identification Numbers Record your snowmobile’ s identific ation numbers and k ey number in the spaces provided below . The key nu mber is stamped on the spare key . The number on the rubber -coated key is in the form of raised dots.
8 SAFETY Operator Safety The following signal words and symbol s appear throughout th is manual and on your vehicle. Y our safety is involved when these words and sym- bols are used.
9 SAFETY Operator Safety Follow the recommended mainte nance program outlin ed beginning on page 71 of this manual to ensure that all critical co mponents on the snowmobile are thoroughl y inspected by your dealer at specific mileage intervals. WAR N I N G Driving a snowmobile requires your full attenti on.
10 SAFETY Operator Safety Stay Clear of T rack Y our snowmobile is propelled by a revo lving track that must be part ially exposed for proper operation.
11 SAFETY Operator Safety Riding Position Operating a snowmobile requires sk ill and balance for proper control. Rider positions may vary with expe rience; but under many conditions, the proper position is to be seated with both feet on the running boards and both hands on the handlebar grips for proper throt tle, brake and steering control.
12 SAFETY Operator Safety Riding Apparel Helmet W earing a helmet can prevent a sever e head injury . Whenever riding a Polaris vehicle, always wear a helmet that meets or exceeds established safety standards. Approved helmets in the USA and Ca nada bear a U.
13 SAFETY Operator Safety Disabled Operators Safe operation of this rid er-active vehi cle requires good judgement and physical skills. Rider Capacity Y our Polaris snowmobile is designed for a single rider only . Do not carry a passenger . Excessive Speed Always observe all state an d local laws governing snowmobile opera- tion and speed limits.
14 SAFETY Operator Safety Driver Awareness Slow down when traveling near poles, posts, or other obstacles. Be especially alert if you’re snowmobiling after dark. Always be on the alert for wire fences. Single strands are especially dangerous, since there may be a great distance between posts.
15 SAFETY Operator Safety Avalanches Snowmobilers should always be properl y trained and equipped before traveling in mountainous terrain: • T ake an av alanche cl ass • T ravel with experienced people • T ravel on designated trails • Make sure each person is equipped with a shovel, probe and avalanche beacon.
16 SAFETY Operator Safety I ce and Snow Build-up Before driving, manually tu rn the skis to the left and right to be sure ice and snow are not interfering with full left and right steering. If dif ficulty is encountered, remove ice and snow build-up that may be obstru cting the steering linkage.
17 SAFETY Operator Safety Driving on Slippery Surfaces Driving in Hilly T errain Use extra caution when operating in hilly terrain. If climbing a hill is unavoidable, keep your weight low and forward.
18 SAFETY Operator Safety Drive Belt Do not operate the engine wi th the drive belt removed. Any servicing that requires operation without a belt must be performed by your dealer . Operation of the engine with the belt removed may result in injury or damage to the engine.
19 SAFETY Operator Safety Inadequate Snow Conditions Since snow provides the only lubrica tion for the power slide suspension and, on liquid cooled mo dels, coo ling for the engine, adequate snow cover is a requirement for op eration of your snowmobile.
20 SAFETY Operator Safety Driving Responsibly Every snowmobile handles differently , and even the mos t docile condi- tions may become dangerous if oper ators drive improperly . If you ’re new to snowmobiling, acquaint your self with the machine and with what it will and won’t do under various conditions.
21 SAFETY Operator Safety Windchill/T emperature Charts The following informatio n is provided to help you determine when tem- peratures become da ngerous for riding.
22 SAFETY Safety Decals and Locations W arning decals hav e been placed on the snowmobile for you r protec- tion. Read and follow the instructions of the deca ls and other warnings on the snowmobile carefully .
23 SAFETY Safety Decals and Locations “No P assenger” Warning Snowmobiles design ed for only a single rider have a warning de cal on the console below the steering post. WARNING This vehi cle is desi gned for operator only . “NO P AS SENGER” T rack W arning The track warning decal is on the rear of the tunnel.
24 SAFETY Safety Decals and Locations Reverse Warning Polaris snowmobiles equipped with electric reverse have a reve rse warning decal on th e console. WARNING Reverse operation, even at lo w speeds, can cause loss of contro l resulting in serious injury or death.
25 SAFETY Safety Decals and Locations Operation W arning (continued from previous page) • Excessive speed, especially at night or with limited visibility , can result in insuffici ent time for you to react to terrain ch anges, to avoid unexpected obstacles , or to stop safely .
26 FEA TURES 16 1. F ront Bumper (do not use for pulling or dragging the snow- mobile) 2. Hood 3. Headlight 4. Windshield 5. Mountain Bar (if equipped) 6. Handlebar 7. Seat 8. T a illights 9. Rear Bumper 10. Snow Flap 11. T rack 12. Suspension 13. T unnel 14.
27 FEA TURES 1. F uel Filler Cap 2. Ignition Switch 3. MFD (Multi-F unction Display) 4. Engine Stop Switch 5. Throttle Control 6. Recoil Starter Handle 7. Hood Hold-Down Straps 8. Brake Lever 9. Park ing Brake 10. Handlebar Gr ip Warmer Switch 11. Thumbwarmer Switch 12.
28 FEA TURES Headlight Dimmer Switch Use the headlight dimmer switch to adj ust the headlights between high beam and low beam. Switch headlig hts to low beam when meeting oncoming traffic. Adjustable Headlights Move the adjuster to the left to lower the headlight beam.
29 FEA TURES Detonation Elimination T echnology (DET) A detonation sensor monitors the engi ne and responds to detonatio n by automatically reducing the engine timin g and adding fuel.
30 FEA TURES Instrumentation MFD Component Identification Item 1 Analog Gauge (if equipped) 2 Digital Gauge 3 Check Engine Indicator 4 Low Oil Indicator 5 High T emp Indicator 6 Brake Indicator 7 Reve.
31 FEA TURES Instrumentation Digital Display Identification Item 1 RPM or Speed Altitude (if equipp ed) Service Interval 2 Electrical System V oltage Level 3 MAX - Maximum MPH/ KPH or RPM MPH - Miles .
32 FEA TURES Instrumentation MFD Settings The MFD Control Switch allows you to set the MFD display to your preferences. The rocker switch h as a MODE button (top) and a SET but- ton (bottom). Specific in structions are outlined on the follo wing pages.
33 FEA TURES Instrumentation MFD Digital Display Programs Press and release the MODE button to cycle through the three MFD pro- grams: Performance, Engine and History . Each program remains active until you cycle to the next program. While any program is active, press and release the SET button to cycl e through the program’ s screens.
34 FEA TURES Instrumentation MFD Digital Display Programs Performa nce Program T rip Settings T rip F automatically displays when the fuel level is low if the snowmobile is equipped with an electronic fuel gauge. The fuel symbol and the last fuel bar on the MFD gauge (if equipped) will blink when the fuel level reaches 1/8 of a tank.
35 FEA TURES Instrumentation MFD Digital Display Programs Engine Prog ram Air T e mperature (accessory) The MFD displays actual air temperature. Press and hold the MODE switch for ten sec- onds to switch between standard and metric units of measurement.
36 FEA TURES Instrumentation MFD Digital Display Programs History Program Press and release the MODE button until the history program screen is active.
37 FEA TURES Instrumentation MFD Digital Display Programs History Program Service Interval Reminder The gauge log s the number of engine hours accumulated between service reminders. When the logged hours reaches the desig- nated service interval (set by the user), the gauge provides a reminder that service is due.
38 FEA TURES Instrumentation Gauge Cleaning 1. Wipe the gauge face as needed using a clean cloth and a mild soap and water solution. W ipe dry with clean, soft cloth. 2. Clean the back side of the gauge using a clean cloth and a mild soap and water solution.
39 THE PERFECT FIT IQ F ront Suspension Adjustments Independent F ront Suspension (IFS) Break in the suspension for approx imately 150 miles (24 0 km) before making any fine-tuning adju stments. Settings will vary from rider to rider , depending on rider weight, vehicle speed, riding style, and trail cond itions.
40 THE PERFECT FIT IQ F ront Suspension Adjustments Air Shocks W alker Evans air shocks can be adju sted for preload and valving. Please see your Polaris dealer for these adjustments. Standard Shocks The tension at which the shock coil spring is set is called spring preload.
41 THE PERFECT FIT IQ F ront Suspension Adjustments F ront Shock Springs (Standard Only) The front springs can be changed if sp ring preload alone isn't suf ficient and further adjustment is desired to control suspension stiffness. See your Polaris dealer for more information.
42 THE PERFECT FIT Rear Suspension Adjustments Rider weight, riding style, trail co nditions, and vehicle speed all af fect suspension action. Each rear suspension can be adjusted to suit rider preference and deliver excellent performance for a given set of conditions.
43 THE PERFECT FIT Rear Suspension Adjustments Initial Spring Preload Setting (Sag Method) T o set up the rear suspension torsion spring preload, measure the distance between the ground and rear bumper . This is measurement X. T ake this measurement with no rider and with the rear suspension at full extension.
44 THE PERFECT FIT Rear Suspension Adjustments T orsion Spring Preload T o adjust rear torsion spring preloa d, rotate the three-position cam using the engine spark plug tool. Diff erent rate torsion springs are available if a firmer ride is desired. Contac t your dealer for more information.
45 THE PERFECT FIT Rear Suspension Adjustments Shock Compres sion V alving Standard Rear T rack Shock The standard RMK rear track shock is an Arvin MPV Select shock th at allows for adjustments to the co mpression val ving. Adjustments are made by tu rning the adjustment screw located near the base of the shock.
46 THE PERFECT FIT Handlebar Adjustments Handlebar position and handlebar angle can be adjusted to rider prefer- ence. After making handlebar adjustme nts, check to make sure wires are not pinched or kinked.
47 THE PERFECT FIT Handlebar Adjustments Handlebar Position 1. Loosen the four bolts on the bottom of the adjuster block. If necessary , pry the blocks apart with a screwdriver . 2. Adjust the handlebar forward or rearward to the desired position. 3. Tighten the bolts.
48 THE PERFECT FIT Accessories Polaris offers a wide range of accesso ries for your snowmobile to help make each ride more enjoyable. Use only Polaris parts and accessorie s on your Polaris snowmobile.
49 PRE-RIDE INSPECTIONS Pre-Ride Checklist Inspect all items on th e checklist for proper operation or condition before each use of the snowmobile. Pr ocedures are outlined on the refer- enced pages. Look for a checkmark ( n ) on the referenced pages to locate the pre-ride inspection items.
50 PRE-RIDE INSPECTIONS Before Starting the Engine Before starting the engine, always re fer to all safety warnings pertaining to snowmobile operation.
51 PRE-RIDE INSPECTIONS Before Starting the Engine n Recoil Rope Inspect the recoil rope and handle fo r exces sive wear , and make sure the knot securing the rope inside the ha ndle is secure. If excessive wear is found, see your Polaris dealer for replacement.
52 PRE-RIDE INSPECTIONS Before Starting the Engine n P arking Brake Lever Lock Use the parking brake lever lock only when you want the sn ow- mobile to remain stationary; for example, when parked on an incline for a period of five min- utes or less. 1.
53 PRE-RIDE INSPECTIONS Before Starting the Engine n Steering System Manually turn the skis completely to the right and to the left . If any dif- ficulty is encountered , remove any ice and snow build-up that may be obstructing the steering linkage.
54 PRE-RIDE INSPECTIONS Before Starting the Engine n Suspension Inspection Loose nuts and bolts can reduce your snowmobile's reliability and cause needless repairs and down time. Befo re beginning any snowmobile trip, a visual inspection will uncover po tential problems.
55 PRE-RIDE INSPECTIONS Start the Engine and Check Before starting the engine, always re fer to all safety warnings pertaining to snowmobile operation. Never en gage the starter when the engine is running. Never start the engine with out checking all ve hicle components to be sure of proper operation.
56 OPERA TION Starting the Engine NOTICE: Engaging the starter when the engine is running WILL result in serious engine damage, especially if the tr ansmission is in reverse. Never engage the starter when the engine is runni ng. 1. Turn the key to the ON position.
57 OPERA TION Engine Break-In No single action on your part is as important to long, trouble-free machine life as proper break-in of a new or rebuilt engine. Premix the first tank of gasoline with one p int of Polaris injection oil for each five gallons of fuel.
58 OPERA TION Engine Break-In Oil Injection System Always fill the oil reservoir when refueling. NOTICE: Serious engine damage can occur without the proper lu brication. Check the oil tank level often during t he first tank of fuel. If the oil level doesn't go down, contact your dealer immediately .
59 OPERA TION T rack W arm-Up Follow these steps to ensure proper warm-up of the engine, drive train and track. 1. Use an appropriate stand to securely support the rear of the snowmobile at the rear bumper . The track sh ould be approximately 4" (10 cm) of f the ground.
60 OPERA TION F uel Safety WAR N I N G Gasoline is h ighly flammable and e xplosive under certain conditions. • Always exercise extreme caution w henever handling gasoli ne. • Always refuel outdoors or in a well-ventilated area. • Always turn off the engine before refueling.
61 OPERA TION Fu e l For peak performance, Po laris recommends the use of 91 octane or higher fuel. Although 87 octane fuel is usable, some engine perfor- mance will be lost and fuel econ omy will decrease. Do not use lower than 87 octane fuel. Do not use fuel containing mor e than 10% ethanol (including E85) .
62 OPERA TION Oil n Low Oil Indicator Light The low oil indicator light will alert th e operator if the oil level is low . V isually check for oil in the bottle. Add oil before further operation of the snowmobile. See page 58 for oi l recommendations.
63 OPERA TION n Engine Stop Switch Push down on the engine stop switch to ground out the ignition and stop the engine quickly . Pull the switch up to the RUN position to allow restarting.
64 OPERA TION n Throttle Lever If the engine stops abruptly when the throttle lever is released: 1. Turn the ignition switch to OFF . 2. V isually inspect the throttle cabl e and throttle body to determine what caused the safety switch to activate. 3.
65 OPERA TION n Emergency Stoppi ng The following chart lists methods for stopping the snowmobile in the event of an emergency . See page 63 for more information about the engine stop switch.
66 OPERA TION Electronic Reverse (PERC t ) Electronic reverse will activate only if the engine RPM is below 4000. The maximum engine RPM will be 6000 when in reverse. NOTICE: Engaging the starter when the engine is running WILL result in serious engine damage, especially if the tr ansmission is in reverse.
67 OPERA TION Electronic Reverse (PERC t ) Engaging Reverse 1. Stop the snowmobile and leave the engine idling. 2. Make sure the area behind yo ur snowmobile is clear . 3. Push the re verse button on the left- hand control for one second, then release.
68 OPERA TION Daily Storage At the end of each ride, park the snowmobile on a level surface and support it at the rear with an appropriate track stand. The track should be suspended approximately 4" (10 cm) of f the ground. Remove the key and cover the snowmobile.
69 MAINTENANCE Emission Control Information Any qualified repair shop or qualifie d person may maintain, replace, or repair the emission control device s or systems on your snowmobile.
70 MAINTENANCE Emission Control Information Owner's Responsibilities Please read the Snowmobile Engine Emissions Limited W arranty , and read the maintenance section of your owner's manual. Y ou are responsi- ble for ensuring that the specified maintenance is performed.
71 MAINTENANCE P olaris Recommended Mainte nance Program T o ensure many trouble-free miles of snowmobiling enjoyment, follow recommended regular maintenance and perform se rvice checks as out- lined in this manual. Record maintenance and service in the Mainte- nance Log begin ning on page 125.
72 MAINTENANCE P eriodic Maintenance Interval T able The following chart is a guide based on average riding conditions. Y ou may need to increase frequency based on ri ding conditions. When inspection reveals the need for replacement parts , always use genuine Polaris parts, available from your Polaris dealer.
73 MAINTENANCE P eriodic Maintenance Interval T able Item See Pag e Fr eque ncy 150 mi. (240 km) 500 mi. (800 km) 1000 mi. (1600 km) 2000 mi. (3200 km) Pre- Season BRAKES Hose Routing -- II II Hose Co.
74 MAINTENANCE P eriodic Maintenance Interval T able I - Inspect (clean, adjust, tighten, lubricate, replace if necessar y) C - Clean R - Replace L - Lubricate Item See Pag e Fr eq u e n c y 150 mi. (240 km) 500 mi. (800 km) 1000 mi. (1600 km) 2000 mi.
75 MAINTENANCE Lubrication F ront Suspension The front suspension does not require lubrication. Rear Suspension Lubricate the suspension pivot shafts with Polaris Pr emium All Season Grease at the intervals outlined in the Periodic Maintenance T able beginning on page 72 and before sea sonal storage.
76 MAINTENANCE Lubrication Driveshaft Bearing Inject grease into th e fitting on the speed- ometer sensor housing until grease pur ges from the seal on the inside of the tunnel. This should take approximately two pumps. Do not use more than four pumps.
77 MAINTENANCE Lubrication n Chaincase Oil Check the chaincase oil leve l at the intervals outlined in the maintenance charts beginning on page 71. The sight glass is located on th e lower rear of the chaincase. Maintain the oil level at or slightly below the center of the sight glass.
78 MAINTENANCE Lubrication Chaincase Oil Oil Change 1. Position the vehicle on a level surface. 2. Remove the drain plug and drain the oil into a drain pan. Allow the oil to drain completely . 3. Clean off all metal shavings from the plug. 4. Install a new sealing washer on the drain plug.
79 MAINTENANCE Spark Plugs Spark plug condition is indicative of engine operation. The spark plug firing end condition should be read after the engine has b een warmed up and the vehicle has been driven at higher spe eds. Immediately check the spark plug for correct color .
80 MAINTENANCE Spark Plugs A new engine can cause temporary spar k plug fouling du e to the preser- vative added during the assembly p rocess. A void prolonged idle speeds, which cause plu g fouling and carbon iza tion. Change the spark plugs every 2000-2500 miles (32 00-4000 km).
81 MAINTENANCE Intake Filters The intake foam filter limits snow ingestion into the intake system. When operating in loose po wder snow , check the top of the foam filter periodically to remove any accumulation of snow . NOTICE: Operating the snowmo bile with the intake filters removed may cause intake icing.
82 MAINTENANCE F uel Injectors All fuel injector service must be performed by an au thorized Polaris dealer . Do not attempt to clean or service the fuel injectors. Fu e l P u m p All fuel pump service must be pe rformed by an authorized Polaris dealer .
83 MAINTENANCE Exhaust System Check the exhaust system for wear or damage at the intervals outlined in the Periodic Maintenance T able beginning on page 71. Always allow the engine and exhaust system to co ol co mpletely before inspecting. 1. Open the hood and ins pect the mu ffler and pipes for cracks or dam- age.
84 MAINTENANCE Cooling System Coolant The coolant supplied in the system is a 60/40 mixture of ethylene-gly col and distilled water . This mix ture provides protection agains t freezing. Contact your dealer if greater protection is required. Use Premium 60/40 anti-freeze coolant, which is already premixed and ready to use.
85 MAINTENANCE Cooling System Coolant High T emperat ure Indicator Light The high temperature indicator light wi ll illuminate when engine cool- ant temperature becomes too hot for safe continued operation of the engine.
86 MAINTENANCE Cooling System Bleeding the Cooling System Use of a non-standard pressure cap will not allow the recovery system to function properly . If the pressure cap needs replacement, contact your dealer for the correct part. NOTICE: If coolant flow becomes restricted or plugged, coolant loss, air lock or engine damage may result.
87 MAINTENANCE Cooling System Bleeding the Cooling System Bleed the cooling system at the intervals outlined in the Periodic Main- tenance T able begin ning on page 72. Perform the bleeding procedure when the engine is cold. 1. Remove the pressure cap and fill the coolant bottle with properly mixed coolant to the maximum mark.
88 MAINTENANCE Drive Chain T e nsion Check drive chain tension weekly and before each long trip. T o obtain correct chai n tension: 1. Rotate the driven clutch counterclockwise to move all chain slack to the tensioner side. Lock the brake lever lock, or have an assistant hold the brake lever firmly .
89 MAINTENANCE Brakes n Hydraulic Brake Inspection Inspect the brake lever travel before eac h use of the sn owmobile. See page 51. Brake pads must be replaced when the brake pad material becomes thin- ner than the backing plate, approximately 1/16" (1.
90 MAINTENANCE Brakes Brake Components •B r a k e D i s c • Bleed Screw •B r a k e L i n e • Brake Caliper • Brake Pad Material - Replace when thickness is less than 1/16" (1.
91 MAINTENANCE Brakes n Brake Fluid NOTICE: Brake fluid will damage decals, paint and so me plastics. Always wipe up spills immediately . Replace brake fluid at least every two years with Polaris DOT 4 high temperature brake fluid. See page 1 10 for the part numbe rs of Polaris products.
92 MAINTENANCE Brakes Bleeding the Hydraulic Brake System Air in the hydraulic brak e system will cause spon gy brake lever action. Bleed the system before operating the snowmobile. During the bleeding proc edure, keep the brake handle as leve l as possi- ble.
93 MAINTENANCE Lights Removing Halogen Bulbs Do not touch a halogen bulb with ba re fingers. Oil from skin leaves a residue, causing a hot spot that w ill shorten the life of the lamp. If fin- gers do touch the bu lb, clean it with an alcohol-moistened towel.
94 MAINTENANCE Clutch System Periodically inspect clutch sheaves for damage, wear or belt residue. T o maintain optimum performance, clean with non-oil based cleaners such as isopropyl alcohol. NOTICE: The bushings in the weights and rolle rs of Polaris clutches are made of a material that may be damaged if lubricated.
95 MAINTENANCE Clutch System n Drive Belt Condition Belt width and length must match the center distance of the clutches and sheave width of the drive clutch. For this reason, Polaris recommends that only O.E.M. belts be used. Ot her belts may match the dimensions, but can drastically change the shif t pattern, resulting in poor perfor- mance.
96 MAINTENANCE Clutch System Drive Belt Removal NOTICE: Do not attempt to remove the dri ve belt after operati ng in reverse. The snowmobile must be stop ped after forward moti on to prevent damage to components during belt removal. 1. Stop the engine after operating in a forward motion.
97 MAINTENANCE Clutch System n Drive Belt Deflection Measure belt deflection with both clutches at rest and in their full neutral position. Place a straight edge on the belt and apply downward pressure while measuring at point A. This measurement should b e 1 1/4" (3.
98 MAINTENANCE T rack Replacement When replacing the track, always inst all a track having the lug size rec- ommended for your mo del. See your Polaris deale r . NOTICE: Installing tracks with larger lugs on machines equip ped with coolers will result in damage to the cooler or tu nnel.
99 MAINTENANCE T rack Lubrication The slide rail requires adequate snow cover for suf ficient lubrication. Excessive wear indicates insufficient lubrication. A new rail slide can cause faster heat build-up in limite d lubrication, resulting in excessive wear .
100 MAINTENANCE T rack T ension T rack tension is critical for maxi mum ef ficiency and performance. T rack tension controls the approach angl e of the track to the rail beam in powder snow conditions. Deep snow performance will be optimized at the specified tension.
101 MAINTENANCE T rack T ension If the track needs adjustment: 5. Loosen the rea r idler shaft bolt. 6. Loosen the lock nuts. 7. Tighten or loosen the track adjus ting screws as necessary to provide equal adjustment on bo th sides of the track. 8. Repeat the measurem ent on the other side of the track.
102 MAINTENANCE n T rack Alignment Periodically check that the track is centered and running ev enly on the slide rails. Misalignment will cause excessive wear to the track and slide rail. 1. Safely support the rear of the snowmobile with the track off the ground.
103 MAINTENANCE Steering System Steering Inspection and Adjustment Check all steering system fa stener s weekly and before a long r ide. T ighten any loose fasteners.
104 MAINTENANCE Steering System Ski Alignment W ith the handlebars in a st raight ahead position, and with veh icle weight compressing the suspension, measure from the straight e dge of the skis at the center of the sk i mounting bolt.
105 MAINTENANCE Steering System n Ski Skags Check skags before each use of the snowmobile to ensu re positive steer- ing characteristics. Skags must be replaced when worn to half their orig- inal diameter . Carbide skags must be replaced if any abnorma l wear or chipping is found.
106 MAINTENANCE Steering System n Rail Slide Wear For ease of inspection, all Polaris rail slides have a wear limit indicator groove to indicate the minimum permissible slide thick- ness. Replace the rail slides if they are worn to the top of the groove at any point along their length.
107 MAINTENANCE Extended Storage Off-season or extended storage of your snowmobile requires preventive measures to aid against deterioration and to prolong the useful life of many componen ts.
108 MAINTENANCE Extended Storage Engine Protection Proper preparation of the engine and fuel system is vital to the preven- tion of rust an d corrosion on precision engine p arts during storage. Whenever the machine is stored for a period of more than 60 days, the engine must be fogged with foggi ng oil.
109 MAINTENANCE Extended Storage Electrical Connections Replace worn or frayed electrical wi re and connec tors. Be sure wiring harness is properly secured awa y from sharp edges, steering linkage, moving parts, and hot exhaust pa rts. T rack and Suspension Moderate track tension should be ma intained during summer storage.
110 POL ARIS PRODUCTS Pa r t N o . Description Engine Lubrica nts 2870791 Fogging Oil (12 oz. Aerosol) 2871098 Premium 2-Cycle Engine Oil (qt.) 2871097 Premium 2-Cycle Engine Oil (gal.) 2871240 Premium 2-Cycle Engine Oil (2.5 gal.) 2871721 Premium Gold Synthetic 2-Cycle Engine Oil (qt.
111 TROUBLESHOOTING Engine T roubleshooting Unless you have experience and traini ng in two-cycle engine repair , see your dealer if technical problems arise. Problem Probable Ca use Solution Erratic engine oper- ating RPM during acceleration o r load variations Drive clutch binding • SEE YOUR DEALER.
112 TROUBLESHOOTING Engine T roubleshooting Problem Probable Ca use Solution Noise in drive sys- tem Broken drive clutch components • SEE YOUR DEALER. Bearing failure/ chaincase, jacks haft, or front drive shaft • SEE YOUR DEALER. Drive belt surface flat spots • Inspect and replace as needed.
113 TROUBLESHOOTING Engine T roubleshooting Problem Probable Ca use Solution Engine turns but fails to start Faulty ignition • Install new spark plug(s). If engine still fails to start, check for spark. If there's no spark, SEE YOUR DEALER. No fuel to engine • Make sure the fuel tank contains fuel.
114 TROUBLESHOOTING Suspension T roubleshooting Problem Solution Rear suspension bot- toms too easily • Set static sag (see page 43). Adjust torsion spring blocks or install optional torsion spri ngs to achieve correct sag dimensions. Rides too stiff in rear • Check for bindi ng suspension components and grease all pivot points.
115 TROUBLESHOOTING Drive Belt T roubleshooting Belt W ear/Burn Diagnosis Causes Solutions Driving at low RPM • Driv e at higher RPM. Gear the machine down . Check belt deflection. Insufficient warm-up • W arm the engine at least five minutes. T ake the drive belt off the ma chine in extremely cold weather and warm it up.
116 W ARRANTY Service And W arra nty Information Obtaining Service and W arranty Assistance Read and understand the service data and the Polaris warranty informa- tion contained in this manual. Contact your Polaris dealer for replace- ment parts, service or warranty .
117 WA RRANTY Service And W arra nty Information Polaris Anti- Theft System The Polaris anti-theft system (P A TS) monitoring program is designed to aid owners of registered snowmobil es in recovery of stolen machines. Administration 1. Polaris snowmobile owner reports theft.
118 W ARRANTY Limited W arranty Polaris Sales Inc., 2100 Highway 55, Me dina, MN 55340, provides a ONE YEAR LIM- ITED W ARRANTY on all components of the Po laris snowmobile ag ainst defects in material or workmans hip. This warranty covers the parts and labor charges for repair or replacement of d efective parts that are cove red by this warranty .
119 WA RRANTY Limitations of warranties and remedies ALL IMPLIED W ARRANTIES (INCLUDING BUT NOT LIMITED TO THE IMPLIED W A RRANTIES OF MERCHANT ABILITY AND FITNESS FOR A P AR- TICULAR PURPOSE) ARE LIMITED IN DURA TION TO THE ABOVE ONE YEAR W ARRANTY PERIOD.
120 W ARRANTY Conditions and Exclusions In order to qualify for warranty , the product must have been properly set up and tested by a Polaris Dealer (if applicable).
121 WA RRANTY Polaris Second Y ear Engine Service Contract Second Y e ar Engine Service C ontract is standard on all el igible new and unused snow- mobiles that were Snow Checked through an au thorized Polaris dealer during the March/April Snow Check promot ion.
122 W ARRANTY Exported V ehicles EXCEP T WHERE SPECIFICALL Y REQUIRED BY LA W , THERE IS NO W AR- RANTY OR SER VICE BULLETIN COVERAGE ON THIS VEHICLE IF IT IS SOLD OUTSIDE THE COUNTR Y OF THE SELL ING DEALER’S AUTHORIZED LOCA- TION. This policy does not apply to vehicles that have received authorization for export from Polaris Industries.
123 WA RRANTY Snowmobile Engine Emis sions Limited W arranty This snowmobile engine emi ssions limited warranty is in addition to the Polaris stan- dard limited warrant y for sn owmobiles.
124 W ARRANTY Snowmobile Engine Emis sions Limited W arranty This limited warranty excludes failures no t caused by a defect in material or workman- ship. This limited warranty doe s not cover damage due to acci dents, abuse, or improper handling, maintenance or use.
125 MAINTENANCE L OG Present this section of your manual to your dealer each time your snow- mobile is serviced. This will provide you and future owners wit h an accurate log of maintenance and servi ces performed on the snowmobile. DA TE MILES (KM) TECHNICIAN SERVICE PERFORMED / COMMENTS 150 mi.
126 MAINTENANCE LOG DA TE MILES (KM) TECHNICIAN SERVICE PERFORMED / COMMENTS.
127 MAINTENANCE LOG DA TE MILES (KM) TECHNICIAN SERVICE PERFORMED / COMMENTS.
128 INDEX A Accessories . . . . . . . . . . . . . . . . . . . 48 Apparel for Riding . . . . . . . . . . . . . . 12 Avalanches . . . . . . . . . . . . . . . . . . . . 15 B Brake Components. . . . . . . . . . . . . . 90 Brake Fluid . . . . . . . . . . .
129 INDEX I Ice and Snow Build- up . . . . . . . . . . . 16 IFS . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Instrumentation . . . . . . . . . . . . . . 30-38 Intake Filters . . . . . . . . . . . . . . . . . . . 81 Intake Silencer . . . . .
130 INDEX S Survival Prep aration . . . . . . . . . . . . 11 Suspension Adjustments, Front . . 39-41 Suspension Adjustments, Rear . . 42-45 Suspension Inspe ction . . . . . . . . . . . 54 Suspension Lubrication, Front . . . . . 75 Suspension Lubrication, Rear .
Ein wichtiger Punkt beim Kauf des Geräts Polaris 600 RMK Shift (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Polaris 600 RMK Shift noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Polaris 600 RMK Shift - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Polaris 600 RMK Shift reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Polaris 600 RMK Shift erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Polaris 600 RMK Shift besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Polaris 600 RMK Shift verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Polaris 600 RMK Shift. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Polaris 600 RMK Shift gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
