Benutzeranleitung / Produktwartung ADW-4100 des Produzenten Planet Technology
Zur Seite of 56
ADSL Wireless Modem Router With 4-port S w itch A DW-4100 User ’ s Manual.
ii Cop y right Copyright (C) 2003 PLANET Technology Corp. All rights reserved. The products and programs described in this User ’ s M anual are licensed products of PLANET Technology, This User ’ .
iii Trademarks The PLANET logo is a trademark of PLANET Technology. This documentation may refer to numerous hard w are and soft w are products by their trade names. In most, if not all cases, these designations are claimed as trademarks or registered trademarks by their respective companies.
i T A BLE OF C ONTENTS CH A P T ER 1 IN T RODUC T IO N ................................................................................ .1 AD W -4100 Feature s ......................................................................................... .
ii Learned MAC T abl e ........................................................................................ . 41 ADSL Con f iguratio n ......................................................................................... . 42 RIP Con f iguratio n .
1 Chapter 1 Introduction This Chapter provides an overview of AD W -4100's features and ca- pabilities. Congratulations on the purchase o f AD W -4100. T he ADSL W ireless Mode m Router w ill allo w m ultiple LAN and W LAN users to share an Internet user account, via a DSL connection.
AD W -4100 User Manual 2 w DMZ. One (1) PC on y our local LAN can be con f igured to allo w unrestricted 2- w a y co mm unication w ith Servers or individual users on the Internet. T his provides the abilit y to run progra m s w hich de m and f or bi-directional co mm uni- cation.
Introduction 3 Ph y sical Details Front Panel 1 2 L AN 3 4 WAN A DSL A CT P WR W L AN ADSL Wireless M odem Router A DW-4100 Figure 1-2: Front Panel LED de f initions LEDs Color Active Description P W R Green ON T he po w er adaptor is connected to the Mo- de m .
AD W -4100 User Manual 4 Restore Default IP A ddress and Clear Pass w ord I f AD W -4100's IP Address or pass w ord is lost, the f ollo w ing procedure can be used to recover f ro m this situation. Pressing the Reset button f or m ore than 10 seconds.
5 Chapter 2 Ins t allation This Chapter covers the physical installation of AD W -4100. S y stem Requirements • PC or T CP/IP co m pliant w or k stations • 32 MB RAM • Ethernet Net w or k Inter .
AD W -4100 User Manual 6 Connect the supplied po w er adapter to AD W -4100 and po w er up. Use onl y the po w er adapter provided. Using a di ff erent one m a y cause hard w are da m age. Step 5 Check the LEDs For each LAN (PC) connection, the corresponding LAN LED should be ON (pro- vided the PC is also ON.
Login And Syste m Status 7 Chapter 3 Login And S y stem S t atus This Chapter details the first time login procedure and the Status screen Login AD W -4100 contains an H TT P server. T his enables y ou to connect to it, and con f ig- ure it, using y our W eb Bro w ser.
AD W -4100 User Manual 8 Figure 3-1: Logon W indow If y ou can't connect I f AD W does not respond, chec k the f ollo w ing: • Machine is properl y installed, LAN connection is OK, and it is po w ered ON. Y ou can test the connection b y using the "Ping" co mm and: • Open the MS-DOS w indo w or co mm and pro m pt w indo w .
Login And Syste m Status 9 Status Home Once y ou login in AD W -4100, its Ho m e page w ill appear. It sho w s the f ir m w are versions and W AN and LAN inter f ace status. Figure 3-2: Home page A DSL T he A DSL Status page sho w s the ADSL ph y sical la y er status.
AD W -4100 User Manual 10 L A N T he L A N page sho w s the in f or m ation and status o f LAN port, DHCP client table, and lin k ing status o f Ethernet inter f ace. Figure 3-4: LAN status PPP T he PPP page sho w s the status o f PPP f or each PPP inter f ace.
11 Chapter 4 S y stem Configuration This Chapter details the configurations for AD W -4100 O v er v ie w T his chapter describes the setup procedure f or: • W AN Access • LAN con f iguration PCs on y our local LAN m a y also require con f iguration.
AD W -4100 User Manual 12 Figure 4-2: Per VC Settings T o s w itch bet w een the PVCs, please choose the options o f virtual circuit and clic k on the Submit button to s w itch over. Figure 4-3: Switch between PVCs Internet connection ser v ices T y pes o f Internet connection services supported b y AD W -4100 are explained belo w .
Syste m Configuration 13 Figure 4-5: Encapsulation types of Bridge mode Step 2 Clic k “ submit ” to co mm it m odi f ications y ou ’ ve done, then clic k “ Sa v e Configura- tion ” to store settings. (Modi f ications w ill not ta k e e ff ects until next reboot.
AD W -4100 User Manual 14 be obtained f ro m ISP. And VCI/VPI values m ust be obtained f ro m the m as w ell, f or so m e local ISPs don ’ t o ff er this in f or m ation activel y . T o set up a PPPoE or PPPoA connection f or W AN, f ollo w the instructions belo w : Step 1 Fill in the VCI/VPI entries w ith the in f or m ation y ou get f ro m ISP.
Syste m Configuration 15 connection handsha k e. T he de f ault value is 1432. A uthentication W hen A U T O option is chosen, the PAP m ode w ill run f irst then CHAP. A utomatic Reconnect I f y ou chec k this option, the Disconnect T i m eout should set to 0 second.
AD W -4100 User Manual 16 Fixed IP for W A N I f y our ISP has assigned static IP address, y ou m a y connect to the Internet b y using a f ixed, or static address. T o set up a Fixed IP f or W AN, do the f ollo w ing steps as an exa m ple. Step 1 Enter the in f or m ation o f Static IP A ddress , Subnet M ask and Gate w a y provided b y ISP.
Syste m Configuration 17 Figure 4-10: DHCP client enable Step 3 Clic k on “ N AT ” tab on le f t panel, and enable the N A PT f unction in the option m enu. Step 4 Clic k “ Sa v e settings ” on le f t panel to w rite con f iguration into m achine, and reboot to m a k e settings e ff ective.
AD W -4100 User Manual 18 Special purpose m ulticast pac k et (such as RIP 2 pac k et) should run w ithout • inter f erence. T able 4-1 IGMP pac k ets process Note : Before the IG M P mode is enabled; please go to the Misc Configuration page to enable the IG M P pro x y.
Syste m Configuration 19 T able 4-2 W AN con f igurations Overvie w Bridge Mode (D y na m ic IP) Router Mode (D y na m ic IP) Router Mode (Static IP) Configuration - W A N Enabled? Y es Y es Y es VPI Provided b y ISP Provided b y ISP Provided b y ISP VCI Provided b y ISP Provided b y ISP Provided b y ISP Static IP Address N/A (0.
AD W -4100 User Manual 20 L A N Configuration T he LAN IP and Subnet Mas k o f AD W -4100 are the values seen b y the users on their internal net w or k .
Syste m Configuration 21 Figure 4-14: DHCP server settings • Ethernet M ode Setting: B y clic k ing this lin k , y ou w ill be directed to Ethernet Mode page. Y ou can speci f y the t y pe o f LAN connection or use AutoSense. De f ault is AutoSense.
AD W -4100 User Manual 22 Figure 4-16: PPP Configuration Ÿ Session Name T his f ield allo w s the user to enter his/her o w n session Na m e to distinguish di f- f erent session f or di ff erent PPP accounts and di ff erent PVCs. Ÿ PVC T his f ield allo w s the user to choose the speci f ic PVC f or PPP session.
Syste m Configuration 23 PPP Con f iguration Status w ill be displa y ed at the botto m o f this page to sho w all the Session Na m es w ith its Adapter (PVC nu m ber), Mode (PPPoA or PPPoE), Service .
AD W -4100 User Manual 24 m ore than one local PC can be associated w ith one W AN Inter f ace. Clic k the Session Na m e Con f iguration lin k to add the session na m e f or W AN inter f ace.
Syste m Configuration 25 Figure 4-19: NAT Session Name Configuration Ÿ Session Name T his f ield allo w s the user to enter his/her o w n session Na m e to distinguish di f- f erent NA T session f or di ff erent inter f aces a m ong di ff erent PPP sessions and di ff erent PVCs.
AD W -4100 User Manual 26 requests o f y our net w or k , AD W -4100 w ill f or w ard those requests to the appropriate co m puter. (Note: DHCP f unction m ust be disabled or the local server itsel f has to be f ix-IP addressed to use this f unction.
Syste m Configuration 27 DNS Configuration T he DNS Configuration page allo w s y ou to set the con f iguration o f DNS prox y . AD W -4100 supports the DNS prox y f unction. For the DHCP requests f ro m local PCs, the DHCP server w ill set the LAN port IP as the de f ault DNS server.
AD W -4100 User Manual 28 pac k ets w ill be f or w arded to the destination PC. Destination M A C W hen the bridge f iltering is enabled, enter the Destination M A C address , select Block and clic k A dd . T hen all inco m ing W AN and LAN Ethernet pac k ets m atched w ith this destination MAC address w ill be f iltered out.
Syste m Configuration 29 T he value o f channel can be selected f ro m channel 1 to 11 f or FCC do m ain, chan- nels 1 to 13 f or E T SI do m ain and 1 to 14 f or Japan do m ain. Securit y Allo w s user to enable or disable the encr y ption f unction.
AD W -4100 User Manual 30 Chapter 5 PC Configuration This Chapter details the PC Configuration required on the local ("Internal") LAN. O v er v ie w For each PC, the f ollo w ing m a y to be.
Syste m Configuration 31 Windo w s 9x/ME 1. Select Control Panel - Network . Y ou should see a screen li k e the f ollo w ing: Figure 5-1: Network Configuration 2. Select the TCP/IP protocol f or y our net w or k card. 3. Clic k on the Properties button.
AD W -4100 User Manual 32 Figure 5-3: Gateway Tab ( W in 95/98) • On the DNS Configuration tab, ensure Enable DNS is selected. I f the DNS Server Search Order list is e m pt y , enter the DNS address provided b y y our ISP in the f ields beside the Add button, then clic k Add .
Syste m Configuration 33 Figure 5-5: Network Configuration ( W in 2000) 3. Select the TCP/IP protocol f or y our net w or k card. 4. Clic k on the Properties button.
AD W -4100 User Manual 34 Figure 5-6: TCP/IP Properties ( W in 2000) 5. Ensure y our T CP/IP settings are correct: Using DHCP T o use DHCP, select the radio button Obtain an IP Address automatically . T his is the de f ault W indo w s settings. Restart y our PC to ensure it obtains an IP Address f ro m AD W -4100.
Syste m Configuration 35 Windo w s XP 1. Select Control Panel - Net w or k Connection. 2. Right clic k the Local Area Connection and choose Properties . Y ou should see a screen li k e the f ollo w ing: Figure 5-7: Network Configuration ( W indows XP) 3.
AD W -4100 User Manual 36 Using DHCP T o use DHCP, select the radio button Obtain an IP Address automatically . T his is the de f ault W indo w s settings.
Syste m Configuration 37 M acintosh Clients Fro m y our Macintosh, y ou can access the Internet via AD W -4100. T he procedure is as f ollo w s. 1. Open the T CP/IP Control Panel. 2. Select Ethernet f ro m the Connect via pop-up m enu. 3. Select Using DHCP Server f ro m the Configure pop-up m enu.
38 Chapter 6 Admin Privilege This Chapter details the operation of AD W -4100 and the status screens. T he lin k s under A dmin Pri v ilege are onl y to be accessed and con f igured, w hen it is login w ith ad m inistrator login na m e and pass w ord.
Ad m in Privilege 39 Figure 6-2 : AT M Status Screen TCP Status T he T CP Status page sho w s the statistics f or all T CP connections. T his is f or internal net w or k onl y .
AD W -4100 User Manual 40 Route Table T he Route T able page displa y s routing table and allo w s y ou to m anuall y enter the routing entr y . T he inter f ace br0 m eans the USB inter f ace; lo0 m eans the loop bac k inter f ace.
Ad m in Privilege 41 S y stem Default Gate w a y Configuration T he s y ste m - w ide De f ault Gate w a y no w provides three options: Auto, User- selected Net w or k Inter f ace, and None.
AD W -4100 User Manual 42 A DSL Configuration T he A DSL Configuration page allo w s y ou to set the con f iguration f or ADSL proto- cols. T rellis T rellis Code. B y de f ault, it is al w a y s enabled. Handshake Protocol T his is f or the ADSL handsha k e protocol.
Ad m in Privilege 43 T his f ield allo w s the user to Enable or Disable the RIP session. T he resulting RIP session w ill m onitor all net w or k inter f aces that are currentl y available f or m essages f ro m other RIP routers. Supplier Inter v al T his f ield allo w s the user to enter the Supplier Interval ti m er in second.
AD W -4100 User Manual 44 • V2 MC: T he supplier trans m its in RIPv2 Multicast. Listener T his f ield allo w s the user to select the Listener Mode (RIP Receive) • V1: T he listener receives the RIPv1 onl y . • V2: T he listener receives the RIPv2 onl y .
Ad m in Privilege 45 Figure 6-9: M iscellaneous Configuration Screen W A N side H TT P ser v er W hen it is enabled, the W eb setting pages o f AD W -4100 can be accessed f ro m the W AN side. Users can li m it the ad m inistration privileges to a speci f ied IP address or li m it to LAN side user.
AD W -4100 User Manual 46 W hen it is enabled, the F T P connection can be established f ro m both the LAN and W AN sides. T F T P ser v er W hen it is enabled, it can upgrade the i m age code w ith the T F T P client application run at either the LAN or W AN sides.
Ad m in Privilege 47 nect: So m e ISPs w ould ter m inate the PPP session due to the inactivit y . For the PPP connect on W A N access , the PPP w ill be auto m aticall y reconnected w hen an URL is entered in the bro w ser (pac k et interested in going out the W AN).
AD W -4100 User Manual 48 Code Image Update T he Code Image Update page allo w s y ou to upgrade the i m age code locall y . Bro w se the location o f f ir m w are f ile, and clic k the Upload to start the update.
49 A ppendix A T roubleshooting This Appendix covers the most likely problems and their solutions. O v er v ie w T his chapter covers so m e co mm on proble m s that m a y be encountered w hile using AD W -4100 and so m e possible solutions to the m .
AD W -4100 User Manual 50 Question 2 I f the PPP is disconnected a f ter the Disconnect T i m eout and ho w can I reconnect it? A ns w er 2 Y ou have to go to the PPP lin k under Status colu m n, choose the correct PVC and Connect option, and then clic k Execute to restart a ne w PPP secession.
51 A ppendix B S pecifications A DW-4100 A / A DW-4100B Product ADSL W ireless Mode m Router Model AD W -4100A AD W -4100B Annex A Annex B ADSL Standards Full-rate ANSI T 1.413 issue 2 and I T U- T G992.1 (G.DM T ), Splitterless I T U- T G.992.2 (G.lite) W ireless Standard IEEE802.
Ein wichtiger Punkt beim Kauf des Geräts Planet Technology ADW-4100 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Planet Technology ADW-4100 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Planet Technology ADW-4100 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Planet Technology ADW-4100 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Planet Technology ADW-4100 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Planet Technology ADW-4100 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Planet Technology ADW-4100 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Planet Technology ADW-4100. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Planet Technology ADW-4100 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
