Benutzeranleitung / Produktwartung VSX-9300TX des Produzenten Pioneer
Zur Seite of 100
AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-9300TX Operating Instructions Register your product at www .pioneerelectronics.com • Protect your new investment The details of your purchase will be on file for reference in the event of an insurance claim such as loss or theft.
W ARNING: Handling the cord on this product or cords associated with accessories sold with the product will expose you to lead, a chemical known to the State of California and other governmental entities to cause cancer and birth defects or other reproductive harm.
READ INSTRUCTIONS — All the safety and operating instructions should be read before the product is operated. RET AIN INSTRUCTIONS — The safety and operating instructions should be retained for future reference. HEED WARNINGS — All warnings on the product and in the operating instructions should be adhered to.
4 En Contents 01 Before you start Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Checking the supplied accessories . . . . . . . . . . . . . . 6 Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 En 08 Controlling other equipment Using the remote control with other components . . 54 Recalling preset codes . . . . . . . . . . . . . . . . . . . . . . 54 Programming signals from other remote controls . . 55 Controls for TVs . . . . . . . . . . .
Before you start 01 6 En Chapter 1 Before you start Features • Easy setup using Advanced Multichannel Acoustic Calibration (MCACC) Setting up for home theater sound is as easy as connecting your speakers, a DVD player or other source, and your TV.
Before you start 01 7 En Ventilation When installing this unit, make sure to leave space around the unit for ventilation to improve heat dispersal (at least 8 in. (20 cm) at the top). If not enough space is provided between the unit and walls or other equipment, heat will build up inside, interfering with performance and/or causing malfunctions.
Before you start 01 8 En Remote control battery indicator When the batteries get too weak to operate the remote control properly an indicator warning screen will appear on the remote. Change the batteries as shown above. This must be done within five minutes or all your remote control settings will be cleared.
5 minute guide 02 9 En Chapter 2: 5 minute guide Introduction to home theater You are probably used to using stereo equipment to listen to music, but may not be used to home theater systems that give you many more options (such as surround sound) when listening to soundtracks.
5 minute guide 02 10 En 3 Connect your speakers. To take full advantage of the receiver’s surround sound capabilities connect front, center, surround and surround back speakers, as well as a subwoofer. Although this is ideal, other configurations with fewer speakers—no subwoofer or no center speaker, or even no surround speakers—will work.
5 minute guide 02 11 En Each speaker connection on the receiver comprises a positive (+) red, and negative (–) black terminal. For proper sound you should take care to match these up with the terminals on the speakers themselves. • If you only have one surround back speaker, hook it up to the surround back left ( Single ) terminal.
5 minute guide 02 12 En Automatically setting up for surround sound The Auto Surround Setup measures the acoustic characteristics of your listening area, taking into account ambient noise, speaker size and distance, and tests for both channel delay and channel level.
5 minute guide 02 13 En 6 Make sure ‘Normal System’ is selected, then select ‘Exit’. • If you are planning on bi-amping your front speakers, or setting up a separate speaker system in another room, read through Surround back speaker setting on page 51 and make sure to connect your speakers as necessary before continuing to step 7.
5 minute guide 02 14 En You can also choose to view all the settings by selecting Next . Press ENTER after you have finished checking each screen. When you’re finished, select Exit to go back to the Surround Setup menu.
Connecting your equipment 03 15 En Chapter 3 Connecting your equipment This receiver provides you with almost limitless possibilities for connecting your audio/video system, but it doesn’t have to be difficult. Depending on your needs, you could be up and running in no time after a few simple connections.
Connecting your equipment 03 16 En • If a connected component does not correspond to the input function ( DVD/LD , etc.), see Assigning the digital inputs on page 75 to assign it properly. 8 Digital audio outputs Two optical digital audio outputs for connecting to a CD- R, MD or other digital recorder.
Connecting your equipment 03 17 En About cable types Analog audio cables Use stereo RCA phono cables to connect analog audio components. These cables are typically red and white, and you should connect the red plugs to R (right) terminals and white plugs to L (left) terminals.
Connecting your equipment 03 18 En Connecting your TV This page shows you how to connect your TV to the receiver. To be able to play the sound from the TV’s built- in tuner, connect the analog audio outputs from your TV to this receiver.
Connecting your equipment 03 19 En Connecting a DVD player Different DVD players offer a different selection of connections, but all should give you at least a digital audio output, stereo analog audio outputs and a video output.
Connecting your equipment 03 20 En Connecting the multichannel analog outputs For DVD Audio and SACD playback, your DVD player may have 5.1, 6.1 or 7.1 channel analog outputs (depending on whether your player supports surround back channels).
Connecting your equipment 03 21 En Connecting a satellite/cable receiver or other set-top box Satellite and cable receivers, and terrestrial digital TV tuners are all examples of so-called ‘set-top boxes’. 1 Connect a set of audio/video outputs on the set- top box component to the TV/SAT AUDIO and VIDEO inputs on this receiver.
Connecting your equipment 03 22 En Connecting a VCR or DVD recorder This receiver has two sets of audio/video inputs and outputs suitable for connecting analog or digital video recorders, including VCRs, DVD-recorders and HDD recorders.
Connecting your equipment 03 23 En Connecting other video sources You can basically use any of the audio/video inputs on this receiver for any kind of video source.
Connecting your equipment 03 24 En Using the component video jacks Component video should deliver superior picture quality when compared to composite or S-video. A further advantage (if your source and TV are both compatible) is progressive-scan video, which delivers a very stable, flicker-free picture.
Connecting your equipment 03 25 En Connecting digital audio sources This receiver has both digital inputs and outputs, allowing you to connect digital components for playback and for making digital recordings. Many digital components also have analog connections for recording analog sources (such as a turntable or tape deck).
Connecting your equipment 03 26 En Connecting analog audio sources This receiver features four stereo audio-only inputs. Two of these inputs have corresponding outputs for use with audio recorders.
Connecting your equipment 03 27 En Connecting a component to the front panel inputs The front panel inputs include a composite video jack ( VIDEO ), an S-video jack ( S-VIDEO ), stereo analog audio inputs ( AUDIO L/R ) and an optical digital audio input ( DIGITAL ).
Connecting your equipment 03 28 En Installing your speaker system To take full advantage of the receiver’s surround sound capabilities connect front, center, surround and surround back speakers, as well as a subwoofer.
Connecting your equipment 03 29 En Connecting the speakers Each speaker connection on the receiver comprises a positive (+) red, and negative (–) black terminal. For proper sound you should take care to match these up with the terminals on the speakers themselves.
Connecting your equipment 03 30 En Connecting antennas The supplied antennas provide a simple way to listen to AM and FM radio. If you find that reception quality is poor, an outdoor antenna should give you better sound quality—see Connecting external antennas below.
Connecting your equipment 03 31 En To improve AM reception, connect a 15–18 ft. length of vinyl-coated wire to the AM LOOP terminals without disconnecting the supplied AM loop antenna.
Controls and displays 04 32 En Chapter 4 Controls and displays Front panel 1 MULTI JOG dial Depending on the operation, you can use this to select an input source or listening mode, as well as for tuner and system settings. It can often be used instead of the remote control / (cursor up/down) buttons.
Controls and displays 04 33 En 10 MULTI CH IN (page 41) Press to select the component connected to the MULTI CH IN terminals (for example, a DVD-Audio player). 11 ACOUSTIC EQ (page 41) Press to select an acoustic calibration EQ setting. 12 MASTER VOLUME dial Adjusts the volume.
Controls and displays 04 34 En Display 1 SIGNAL indicators (page 42) Light to indicate the currently selected input signal. AUTO lights when the receiver is set to select the input signal automatically. 2 Digital format indicators • PRO LOGIC II – Lights during Dolby Pro Logic II and Pro Logic IIx processing.
Controls and displays 04 35 En Remote control 1 Remote Control Display Screen 2 SOURCE Use this button to turn on/off other components. You must input the component preset code in order to do this (see Using the remote control with other components on page 54).
Controls and displays 04 36 En 6 / / / /ENTER buttons Use to navigate menus and select options/execute commands. 7 AUDIO Use to switch the audio tracks of a DVD when a DVD player is selected as the input source.
Listening to your system 05 37 En Chapter 5 Listening to your system Auto playback • Default setting: On There are many ways to listen back to sources using this receiver, but for the simplest, most direct listening option is the Stream Direct feature.
Listening to your system 05 38 En The MOVIE listening modes These modes are specifically designed for watching movies. The basic modes provide pure decoding of multichannel sources, and will create surround channels for two channel sources.
Listening to your system 05 39 En The MUSIC listening modes These modes are specifically designed for listening to music. The basic modes provide pure decoding of multichannel sources, and will create surround channels for two channel sources.
Listening to your system 05 40 En Neo:6 Music settings • Default setting: 2 When listening to 2-channel sources in Neo:6 Music mode, you can adjust the center image to create a wider stereo effect with vocals. Note that this is only available when using a center speaker.
Listening to your system 05 41 En Using the multichannel analog inputs If you’ve connected to the multichannel inputs on the rear panel (see Connecting the multichannel analog outputs on page 20), you will be able to select them as your input source.
Listening to your system 05 42 En Selecting the input signal type Most of the audio inputs have both analog and digital jacks. You can select the type of signal to be used in each case. The input signal type for the current input is indicated in the display.
Listening to your system 05 43 En Using the surround back channel • Default setting: SB CH ON You can have the receiver automatically use 6.1 or 7.1 decoding for 6.1 encoded sources (for example, Dolby Digital EX or DTS-ES), or you can choose to always use 6.
Listening to your system 05 44 En Listening with virtual surround back speakers • Default setting: VIRTL SB OFF If you don’t have real surround back speakers connected, you can use the Virtual Surround Back feature to simulate one. Sometimes the material may sound better in the 5.
Listening to your system 05 45 En Using Midnight and Loudness listening • Default setting: Off The Midnight listening feature makes quieter sounds more audible, allowing you to hear effective surround sound at low volume levels. The Loudness feature boosts the bass and treble in audio sources, useful for listening at low volumes.
Listening to your system 05 46 En • If you switch on the tone control when DIRECT is selected, the receiver automatically switches to STEREO . Reducing noise during playback • Default setting: Off.
Using the tuner 06 47 En Chapter 6 Using the tuner Finding a station The following steps show you how to tune in to FM and AM radio broadcasts using the automatic (search) and manual (step) tuning functions. If you already know the exact frequency of the station you want to listen to, see Tuning directly to a station below.
Using the tuner 06 48 En MPX mode If there is interference or noise during a stereo FM radio broadcast (the STEREO indicator is lit), or the radio reception is weak, press MPX on the remote to switch the receiver into mono reception mode (the MONO indicator lights).
Using the tuner 06 49 En Listening to memorized station presets You can do this from both the remote control and the front panel. 1 Press CLASS to select the class in which the station is stored. Press repeatedly to cycle through the three memory classes, A , B and C .
The Surround Setup menu 07 50 En Chapter 7 The Surround Setup menu Making receiver settings from the Surround Setup menu This receiver allows you to make detailed settings to optimize the surround sound performance. You only need to make these settings once (unless you change the placement of your current speaker system or add new speakers.
The Surround Setup menu 07 51 En • SurrBack System – Specify how you are using your surround back speakers (see Surround back speaker setting below). • Auto Setting – This is a quick and easy automatic surround setup (see Automatically setting up for surround sound on page 12).
The Surround Setup menu 07 52 En Use / (cursor up/down) to select the size (and number) of each of the following speakers: • Front – Select LARGE if your front speakers reproduce bass frequencies effectively, or if you didn’t connect a subwoofer.
The Surround Setup menu 07 53 En 3 Adjust the level of each channel using the / (cursor up/down) buttons. If you selected Manual , use / (cursor up/down) and ENTER to select speakers. The Auto setup will output test tones in the order shown on-screen: Adjust the level (+/– 10dB) of each speaker as the test tone is emitted.
Controlling other equipment 08 54 En Chapter 8 Controlling other equipment Using the remote control with other components The supplied remote control can operate not only this receiver, but also your TV, DVD player and other components.
Controlling other equipment 08 55 En 8 Repeat steps 3 – 7 for any other components you want to control. 9 When you’re finished, use / (cursor up/down) to select ‘*Exit*’ from the menu and press ENTER.
Controlling other equipment 08 56 En Controls for TVs This remote control can control components after entering the proper codes or teaching the receiver the commands (see Using the remote control with other components on page 54 for more on this). Use the MULTI CONTROL buttons to select the component.
Controlling other equipment 08 57 En Controls for other components This remote control can control these components after entering the proper codes or teaching the receiver the commands (see Using the remote control with other components on page 54 for more on this).
Controlling other equipment 08 58 En • Depending on the maker and individual model, there are some buttons that may not be able operate some equipment or may operate it in a different way. • The default preset setting for all functions is a corresponding Pioneer component.
Controlling other equipment 08 59 En Direct function • Default setting: On (all components) You can use the direct function feature to control one component using the remote control while at the same time, using your receiver to playback a different compo- nent.
Controlling other equipment 08 60 En 4 Use / (cursor up/down) to select a command in the sequence then press ENTER . If this is the first command in the sequence, select 1st Cmmnd . Otherwise, simply choose the next command in the sequence. 5 To add (or change) a command select ‘Change’ and press ENTER.
Controlling other equipment 08 61 En Using System off • Press SYSTEM OFF. The command sequence you programmed will run, then all Pioneer components will switch off, followed by this receiver.
Using other functions 09 62 En Chapter 9 Using other functions Making an audio or a video recording You can make an audio or a video recording from the built-in tuner, or from an audio or video source connected to the receiver (such as a CD player or TV).
Using other functions 09 63 En Watching video and audio sources independently You can listen to a sound source and select a different video source on your TV. • While listening to a source, press RECEIVER, then VIDEO SEL to select the video source you want to watch.
Using other functions 09 64 En Switching the speaker impedance • Default setting: Speaker 8 Ω Ω Ω Ω You can use speakers with a nominal impedance between 6–16 Ω but if you are using speakers with an impedance of less than 8 Ω , you must change the impedance setting below.
Using other functions 09 65 En 4 Press the button you want to rename. 5 Edit the button as necessary. Use / (cursor up/down) to select letters and/or numbers and use / (cursor left/right) to move the cursor forward/back a position. The name can be up to eight characters (the possible characters are listed below).
Using other functions 09 66 En Resetting the system Use this feature to reset the system to its factory default settings. 1 Switch the receiver into standby. 2 While holding down the front panel TONE button, press and hold STANDBY/ON for about three seconds.
Other connections 10 67 En Chapter 10 Other connections Caution • Before making or changing the connections , switch off the power and disconnect the power cord from the power outlet. Plugging in components should be the last connection you make with your system.
Other connections 10 68 En Bi-amping your front speakers Bi-amping is when you connect the high frequency driver and low frequency driver of your speakers to different amplifiers (in this case, to both front and surround back terminals) for better crossover performance.
Other connections 10 69 En Multi-room listening This receiver can power two independent systems in separate rooms after you have made the proper multi- room connections. Different sources can be playing in both rooms at the same time or, depending on your needs, the same source can also be used.
Other connections 10 70 En Using the multi-room controls You can use the front panel controls to adjust the sub room volume and select sources. 1 Press the MULTI ROOM & SOURCE ON/OFF button on the front panel.
Other connections 10 71 En Connecting an IR receiver If you keep your stereo components in a closed cabinet or shelving unit, you can use an optional IR receiver (such as a Niles or Xantech unit) to control your system instead of the remote sensor on the front panel of this receiver.
Other connections 10 72 En Using the USB interface It is possible to listen to two channels of audio from your computer by connecting to the USB interface on the rear of this receiver.
Other connections 10 73 En Connecting a PC for Advanced MCACC output If you use the Professional Acoustic Calibration (see page 84) to measure the reverb characteristics of your listening room, you can check the results graphically using a computer connected to this receiver.
Advanced setup 11 74 En Chapter 11 Advanced setup The System Setup menu The System Setup menu is where you can make customized settings to reflect how you are using the receiver. 1 Switch on the receiver and your TV. 2 Using the remote control, press RECEIVER, then press the SYSTEM SETUP button.
Advanced setup 11 75 En THX CINEMA Setup • Default setting: PLII / PLIIx MOVIE If you want, you can choose which decoding method the receiver will use for 2-channel sources when you’ve selected the THX CINEMA mode (see Listening in surround sound on page 37 for details).
Advanced setup 11 76 En 3 Select the component that corresponds with the one you connected to that input Select between DVD/LD , TV/SAT , VCR1 , VCR 2 , CD , CD-R or MD .
Advanced setup 11 77 En Use the front panel MULTI JOG dial (or / on the remote) to change the character and ENTER to move forward a position. If you want to change a character you input, you can press RETURN to go back one position. The name can be up to ten characters (the possible characters are listed below).
Advanced setup 11 78 En Multi-Room and IR receiver setup • Default setting: VARIABLE / Setting 1 If you’ve made multi-room connections (see Multi-room listening on page 69) you may need to specify your volume setting. Also use this menu to specify your IR receiver type (if necessary).
Advanced setup 11 79 En The Expert setup menu The settings in the Expert setup menu are more advanced features of this receiver that you can use to make detailed adjustments when you’re more familiar with the system. Before making these settings, you should have already completed Automatically setting up for surround sound on page 12.
Advanced setup 11 80 En Crossover Network • Default setting: 80Hz This setting decides the cutoff between bass sounds playing back from the speakers selected as LARGE , or the subwoofer, and bass sounds playing back from those selected as SMALL . It also decides where the cutoff will be for bass sounds in the LFE channel.
Advanced setup 11 81 En Fine Channel Delay For proper sound depth and separation with your system, it is necessary to add a slight bit of delay to some speakers so that all sounds will arrive at the listening position at the same time.
Advanced setup 11 82 En !! Complete !! is displayed on-screen after the Acoustic Calibration Equalization is set. If you want to check the settings, select Check . Select Next after you have finished checking each screen. • If you want to copy these settings and adjust them manually, select Data Copy .
Advanced setup 11 83 En Copying your Acoustic Calibration EQ settings If you want to manually adjust the Acoustic Calibration EQ (see Setting the Acoustic Calibration EQ manually above), we recommend .
Advanced setup 11 84 En Professional Acoustic Calibration This setup minimizes the unwanted effects of room reverberation by calibrating your system based on the direct sound coming from the speakers. It can also provide you with a graphical output of the frequency response of your room.
Advanced setup 11 85 En Note that changing the room (for example, moving furniture or paintings) will affect the calibration results. In such cases, you should recalibrate your system. Using Professional Acoustic Calibration 1 Select ‘Acoustic Cal EQ’ from the Expert setup menu.
Advanced setup 11 86 En • If No Data is displayed, you will need to make a reverb measurement using the Auto Pro or Reverb Measurement setup option. 7 If you selected ‘Advanced EQ Setup’, input the time setting you want to use for calibration, then select ‘Start’.
Advanced setup 11 87 En • If the YES or PLUS setting on the subwoofer is selected (in Speaker Setting on page 51), the test tone will only play back from the subwoofer. If not, the test tone will play back from the front and surround speakers set to LARGE .
Additional information 12 88 En Chapter 12 Additional information Troubleshooting Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component.
Additional information 12 89 En No sound Symptom Cause Remedy No sound is output when an input source is selected. • Improper connections. • Make sure you have properly connected the component to the corresponding input on the back of the receiver (see Connecting your equipment on page 15).
Additional information 12 90 En Other audio problems No sound from one speaker . • The speaker setting has been set to NO .• Change the setting in Speaker Setting on page 51. • The speaker level is too low . • Check the level in Channel Level on page 52.
Additional information 12 91 En Video Can't record audio. • Y ou are tr ying to make an analog recording from a digital signal, or a digital recording of an analog source. •Y ou can only record analog to analog, or digital to digital. • The digital source is copy protected.
Additional information 12 92 En Settings Display Can’t record video. • Y ou are tr ying to record a source connected to the component video jacks. • Connect the source component to either the composite video or the S-video jacks (see Connecting your equipment on page 15).
Additional information 12 93 En Remote control USB interface When playing a disc, the 2 PRO LOGIC II or Neo:6 indicator lights on the receiver. • The input signal type is set to analog. • Set the receiver to AUTO or DIGITAL (see Selecting the input signal type on page 42).
Additional information 12 94 En Note • If the unit does not operate normally due to external effects such as static electricity, disconnect the power plug from the outlet and insert again to return to normal operating conditions.
Additional information 12 95 En Surround sound formats Below is a brief description of the main surround sound formats you’ll find on DVDs, satellite, cable and terrestrial broadcasts, and video cassettes. Dolby The Dolby technologies are explained below.
Additional information 12 96 En About THX The THX technologies are explained below. See www.thx.com for more detailed information. THX Cinema processing THX is an exclusive set of standards and technologies established by the world-renowned film production company, Lucasfilm Ltd.
Additional information 12 97 En Preset code brands DVD Pioneer Denon JVC Philips Panasonic RCA Samsung Sony Toshiba Yamaha LD Pioneer Denon Kenwood Panasonic Philips Sony Yamaha CD-R Pioneer Denon JVC.
Additional information 12 98 En Specifications Amplifier section Continuous average power output of 110 watts* per channel, min., at 8 ohms, from 20 Hz to 20,000 Hz with no more than 0.09%** total harmonic distortion (front). Continuous Power Output Front.
Additional information 12 99 En S001_En Selecting fine audio equipment such as the unit you’ve just purchased is only the start of your musical enjoyment. Now it’s time to consider how you can maximize the fun and excitement your equipment offers.
PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. BOX 1540, Long Beach, California 90810-1540, U.
Ein wichtiger Punkt beim Kauf des Geräts Pioneer VSX-9300TX (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Pioneer VSX-9300TX noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Pioneer VSX-9300TX - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Pioneer VSX-9300TX reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Pioneer VSX-9300TX erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Pioneer VSX-9300TX besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Pioneer VSX-9300TX verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Pioneer VSX-9300TX. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Pioneer VSX-9300TX gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
