Benutzeranleitung / Produktwartung CS-9134 des Produzenten ATEN Technology
Zur Seite of 34
2005-12-21 User Manual CS-9134 CS-9138.
2005-12-21 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Packing List The complete Master View CS-9134 / CS-9138 package consists of: w 1 CS-9134 or CS-9138 KVM Switch w 1 Power Adapter w 1 Rack Mounting Kit w 1 User Manual w 1 Quick Start Guide Check to make sure that the unit was not damaged in shipping. If you encounter a problem, contact your dealer.
Contents Packing List .................................i i i Contents ...................................i v Overview ...................................1 Features ...................................2 Hardware Requirements ...........................3 Console .
Overview The Master View CS-9134 and CS-9138 KVM switches are control units that allow access to multiple computers from a single console (keyboard, monitor, and mouse). Before the development of the Master View, the only way to control multiple computer configurations from a single console was through a complex and costly network system.
Features w Cascadable To Three Levels - Control Up to 64 (CS-9134) or 512 (CS-9138) Computers From a Single Console w No Software Required - Computer Selection via Front Panel Switches, Hot Keys, or O.
Hardware Requirements Console w A VGA, SVGA, or Multisync monitor capable of the highest resolution that you will be using on any computer in the installation. w A PS/2 style mouse w A PS/2 style keyboard Computers The following equipment must be installed on each computer: w A VGA, SVGA or Multisync card.
Introduction CS-9134 Front View 1. Port Selection Switches Press a switch to access the computer attached to the corresponding port. w Pressing Buttons 1 and 2 simultaneously for 3 seconds performs a Keyboard and Mouse Reset. w Pressing Buttons 3 and 4 simultaneously starts Auto Scan Mode.
CS-9138 Front View 1. Port Selection Switches Press a switch to access the computer attached to the corresponding port. w Pressing Buttons 1 and 2 simultaneously for 3 seconds performs a Keyboard and Mouse Reset . w Pressing 7 and 8 simultaneously starts Auto Scan Mode.
Rear View 1. Power Jack The unit is designed to be non-powered (external power is not required - its operating power comes from the computers). In general, the only time that external power is necessary is when you cascade it, or if operation becomes erratic because the unit isn’t obtaining enough power from the computer connections.
Installation Before you Begin Single Station Installation In a Single Stage installation, there are no additional Master View’s cascaded down from the first unit. To set up a single stage installation do the following: 1. Plug your keyboard, mouse, and monitor into the unit’s Console Ports.
Two Stage Installation To control even more computers, up to four (CS-9134) or eight (CS-9138) additional Master View units can be cascaded from the CPU ports of the First Stage unit. The cascaded Master Views that connect back to the First Stage unit are considered Second Stage units.
Three Stage Installation The procedures for setting up a three stage installation are essentially the same as for a two stage installation. With a three stage setup, as many as 64 (CS-9134) or 512 (CS-9138) computers can be controlled in a complete installation.
4. Plug the power adapter cable into the Master View’s Power Jack, then plug the adapter into an AC power source. 5. Repeat these steps for any other Third Stage units you wish to connect. 6. Plug in the power adapters for all the Second Stage Master View units.
Operation Hot Plugging The Master View CS-9134 / CS-9138 supports hot plugging. Components can be removed and added back into the installation by unplugging and replugging their cables from their respective ports without the need to shut the switch down.
Powering Off and Restarting If it becomes necessary to Power Off one of the Master View units, before starting it back up you must do the following: 1.
Port Selection The Master View CS-9134 / CS-9138 provides three methods to obtain instant access to any computer in your installation: Manual, Hotkey , and OSD. u Manual Simply press the appropriate Port Selection Switch on the Master View’s front panel.
Port ID Numbering Each CPU Port on a Master View installation is assigned a unique Port ID . You can directly access any computer on any level of the installation by specifying the Port ID of the CPU port that the computer is connected to - either with the Hotkey port selection method, or with the OSD.
Port Key In Examples 1. To access a computer attached to port 3 of a Single Stage installation, key in 3 for the Port ID, as follows: [Ctrl]+[Shift]+[Alt] 3 [Enter] 2.
OSD OSD Overview The On Screen Display (OSD) provides a menu driven interface to handle all computer control and switching procedures. Although Hotkey switching still works, using OSD is a great deal more convenient - especially in large, cascaded installations where it is difficult to keep track of which port a particular computer is attached to.
OSD Navigation w [Esc] cancels the current selection, or dismisses the current menu and moves back to the menu one level above. If you are at the highest menu level, it deactivates OSD. w To move up or down through the list one line at a time, Click the Up and Down Triangle symbols ( st ), or use the Up and Down Arrow Keys.
OSD Main Screen Headings Heading Explanation PN This column lists the Port ID numbers (Station Number - Port Number), for all the CPU ports on the installation. The simplest method to access a particular computer is move the Highlight Bar to it, then press [Enter].
u F2 SCAN: Pressing [F2] initiates Quick View Scanning , in which the OSD cycles through all the ports that are currently selected for this with the QV feature (see F4 QV , below). It stays on each port for the amount of time set with the Scan Duration setting under the F6 SET function (see p.
u F3 LIST: This function lets you broaden or narrow the scope of which ports the OSD lists. On the submenu that appears, an icon of a pointing finger indicates the currently selected choice. To change a setting, move the highlight bar to the choice you want, then press [Enter].
u F4 QV: QV lets you select which ports you want to include for automatic scanning under the Quick View Scanning function (see F2, above). [F4] is a toggle. To select/deselect a port, move the highlight bar to it, then press [F4]. When a port has been selected, an arrowhead displays in the QV column to indicate so.
u F6 SET: Pressing [F6] brings up the OSD configuration menu. To change a setting: 1. Move the highlight bar to the choice you want (an icon of a pointing finger indicates which choice is the currently selected one), then press [Enter]. 2. On the submenu that appears, move the highlight bar to the choice you want and press [Enter].
Setting Function SET PASSWORD Allows you to set a password in order to control access to: Clearing the Name List; Restoring Default Values; and Locking/Unlocking the Console. See the OSD Security Features section, below, for password setting details. CLEAR THE NAME LIST* Clears all Port Names from the Name List.
OSD Factory Default Settings The factory default settings are as follows: Setting Default Display Duration Always On Display Mode The Port Number plus the Port Name Scan Duration 3 Seconds OSD Security In order to prevent unauthorized access to the systems, the OSD provides a password security feature.
Appendix Computer Connection Tables The following tables indicate the relationship between the number of Master View Units and the number of systems that they control: u CS-9138: MVs Computers MVs Com.
u CS-9134: MVs Computers MVs Computers MVs Computers MVs Computers 1 4 7 1 9-2 2 1 3 3 7-4 0 1 9 5 5-5 8 2 4-7 8 2 2-2 5 1 4 4 0-4 3 2 0 5 8-6 1 3 7-1 0 9 2 5-2 8 1 5 4 3-4 6 2 1 6 1-6 4 4 1 0-1 3 1 0.
Stacking and Rack Mounting u Stacking CS-9134 / CS-9138 switches can be stacked one on top of the other using the stacking brackets that come already attached to the unit. Line up the four bottom brackets of the top unit with the four top brackets of the bottom unit; then fit the top unit down onto the bottom unit.
u Rack Mounting To rack mount the unit do the following: 1. First remove the stacking brackets by unscrewing them from the unit, as shown in the diagram below: 2. Next screw the mounting brackets into the sides of the unit, as shown in the diagram below: 3.
Specifications Function CS-9134 CS-9138 Computer Connections Direct 4 8 Max 64 (via Cascade) 512 (via Cascade) Port Selection Front Panel Switches; Hotkeys; OSD LEDs Power 1 (Blue) On Line 4 (Green) 8.
2005-12-21 30 CS-9134 / CS-9138 User Manual Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR’S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM THE DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, DISK OR ITS DOCUMENTATION.
Ein wichtiger Punkt beim Kauf des Geräts ATEN Technology CS-9134 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie ATEN Technology CS-9134 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für ATEN Technology CS-9134 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von ATEN Technology CS-9134 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über ATEN Technology CS-9134 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon ATEN Technology CS-9134 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von ATEN Technology CS-9134 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit ATEN Technology CS-9134. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei ATEN Technology CS-9134 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
