Benutzeranleitung / Produktwartung KX-F160 des Produzenten Panasonic
Zur Seite of 64
Plain Paper FAX Model No. K X-F16 00 Contents Setting up the Unit for Printing Using the Unit with Windows g Using the Unit with MS-DOS g Applications Troubleshooting and Routine Care Specifications Please read these Operating Instructions before using the unit and save for future reference.
2 End-User License Agreement THIS IS A LEGAL AGREEMENT BETWEEN YOU AND PANASONIC. CAREFULLY READ ALL THE TERMS AND CONDITIONS OF THIS AGREEMENT PRIOR TO OPENING THE PACKET OF SOFTWARE PROGRAM. OPENING THE PACKET INDICATES YOUR ACCEPTANCE OF THESE TERMS AND CONDITIONS.
3 (INCLUDING NEGLIGENCE), STRICT PRODUCT LIABILITY OR OTHERWISE, EVEN IF SUCH PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Trademarks Canon and BJ are registered trademarks of Canon Inc. Centronics is a registered trademark of Centronics Data Computer Corporation.
4 Setting up the Unit for Printing Table of contents Connecting the unit to a computer RRRRRRRRRRRRRRRRRR 6 Selecting the print cartridge RRRRRRRRRRRRRRRRRRRRR 7 Turning the printer mode on/off RRRRRR.
5 Troubleshooting and Routine Care Error messages on the display RRRRRRRRRRRRRRRRRRRR 50 Before requesting help RRRRRRRRRRRRRRRRRRRRRRR 51 Paper loading problems RRRRRRRRRRRRRRRRRRRRR 51 Print quality.
6 3 Turn the unit and the computer on. Connecting the unit to a computer The unit has an 8-bit parallel interface jack, which allows you to use it with IBM PCs and compatible computers. You need to purchase a Centronics-compatible, parallel interface cable from your dealer.
7 Setting up the Unit for Printing Selecting the print cartridge The print cartridges that can be used are: » Included print cartridge or KX-FA150 Print Cartridge (option) for black and white printing Use this cartridge for printing draft and monochrome documents.
8 Before loading paper Selecting the print media You can print on the following print media. Ink Jet Paper: This paper is specially developed for color printing with ink jet printers. Canon Bubble Jet Paper LC-301 for BJC-4100 is recommended. Only letter size is available.
9 Setting up the Unit for Printing Setting the paper thickness lever Use the paper thickness lever to adjust the distance between the print head and the paper to accommodate different paper thicknesses. 1 Slide the front lid open lever towards you to open the front lid.
10 Loading paper There are two paper feed procedures: automatic sheet feed and manual feed. Using automatic sheet feed Use this procedure for ink jet paper, ink jet transparencies and other media other than thick paper or resume paper. You can stack about 100 sheets of plain paper (20 lb or 95 g/m 2 ) in the paper tray.
11 Setting up the Unit for Printing Using manual feed Use this procedure for thick paper (24 lb to 28 lb or 91 g/m 2 to 105 g/m 2 ) or resume paper. 1 Pull the paper rest up until it stops. 2 Set the paper selection lever to the front position. 3 Insert a single sheet of paper into the paper tray.
12 Loading envelope You can stack up to 15 envelopes in the sheet feeder or you can manually feed envelopes one at a time. U.S. Commercial number 10 envelopes and Envelope DL envelopes are recommended. Important: ¡ The following envelopes are not recommended because they may cause jams or smears, or may damage your unit.
13 Setting up the Unit for Printing Loading Envelope DL envelopes When you use Envelope DL or envelopes that are shorter than 8 3 ⁄ 4 inch (222 mm) in width, you can load up to 15 envelopes at a time and use the automatic sheet feeding. 1 Set the paper thickness lever to the right.
14 Using buttons for printer PRINT MODE button Use this button to select the print mode with MS- DOS applications. For details, see page 35. If you are using Windows, the printer driver automatically selects the print mode. FF button Use this button to load a new sheet of paper or eject a sheet of paper from the unit.
1 Initialize the computer using Windows 3.1 or 3.11. 2 Insert the diskette (provided) into disk drive A (or B). 3 From the Program Manager, click File . Then click the Run... option. 4 Type a: (or b:) install in the Filename field of the Run dialog, then click OK .
16 Setting as the default printer After installing the printer driver for Windows 95, set the unit as the default printer by the following procedures. Installing the printer driver for Windows 95 1 Click Start , move the pointer to Settings and click Printers .
17 Using the Unit with Windows Printing documents from Windows applications Printing documents in black and white When printing a document using Microsoft Word, proceed as follows. 1 Start the application software in the Windows environment. 2 Open the document you want to print.
Printing documents in color When printing a document using Microsoft Word, proceed as follows. 18 ¡ For details on printer options, see pages 19 to 26. 7 After selecting the options you want, click OK to close the driver dialog box. 8 For Microsoft Word 6.
19 Using the Unit with Windows Setting up the printer driver Selecting printer options in Main dialog The Main dialog contains the most important control for the printer drivers. A User Setting option Use this option to select one of the defined processing settings of the driver.
20 B Paper Source option This setting defines how paper (or other print media, such as ink jet transparencies) will be fed into the unit. Click on the arrow next to the Paper Source setting and selec.
21 Using the Unit with Windows Ink Jet Transparency: Used for transparency film (such as that used in overhead projectors). Paper selection lever: Set to the back position. Paper thickness lever: Set to the center position. Ink Jet Glossy Paper: Paper selection lever: Set to the front position.
22 Using Settings... dialog The “Settings...” dialog allows you to adjust and save all quality selections, color modes and halftone settings of the driver under a specific name. In this way, you can restore a special setting you need by selecting another User Setting in the Main window.
23 Using the Unit with Windows C Print Quality option The Print Quality settings are used to define the overall quality of the document printed by the unit.
24 E Halftoning option The Halftone setting defines how mixing of colors is performed and printed by the unit. The unit contains four colors of ink: cyan, magenta, yellow, and black. Intermediate colors can be created by mixing combinations of these inks.
25 Using the Unit with Windows Using Papers... dialog This window allows you to define and save your own paper sizes and make them available to the unit and your applications. Click on the Papers... tab to display the following window. A Defi ne a new Paper Size To define a new paper size, proceed as follows.
26 Printer driver information By pressing the “About...” tab, a dialog box will appear showing information on; — Windows version, — Driver version, — Subsystem version, — Creation date, etc. Please keep this information ready if you call the hotline.
27 Using the Unit with Windows Changing the default dialog language The driver dialogs, messages and its helpfiles are in four languages: English (US and UK), French, German and Spanish. At installation time the installer program detects the country setting and sets the drivers default dialog language.
28 Selecting a printer driver with MS-DOS applications The installation programs for most applications offer a list of printer drivers from which to choose. If you find Panasonic KX-F1600 on the list, select it. This will give you the fullest range of features.
Epson LQ mode BJ mode Print style Emulation mode Epson LQ mode BJ mode Typeface Emulation mode * In BJ mode, Courier at 12 cpi is available in HS mode only.
Settings Emulation mode Epson LQ mode BJ mode 30 Setting the printer emulation Follow this procedure to set the printer emulation. You can select either Epson LQ or BJ emulation. The factory preset setting is LQ emulation. 1 Make sure the printer mode is turned off.
31 Using the Unit with MS-DOS Applications Changing settings for LQ emulation The following list shows the settings you can customize and explains each one. TEXT SCALE SET: You can select the number of lines (62 or 66 lines) that can fit on a piece of paper.
32 Changing settings for BJ emulation The following list shows the printer settings you can customize and explains each one. TEXT SCALE SET: You can select the number of lines (62 or 66 lines) that can fit on a piece of paper. If the software application you are using assumes that each piece of paper equals 66 lines, select ENABLE.
33 Using the Unit with MS-DOS Applications Follow this procedure to customize the unit when using BJ emulation. 1 Press (MENU) until the following is displayed. 2 Press (START/SET) . 3 Press (‹) or (›) to select BJ emulation. 4 Press (START/SET) .
34 Printing a printer setup list and a printer test list You can obtain the following lists. Printer setup list — provides you with the current settings in each emulation mode. Printer test list — provides all characters in the emulation mode you set.
35 Using the Unit with MS-DOS Applications Selecting print quality If you are not using Windows, you may need to set the print mode for MS-DOS applications. Your unit incorporates several print modes that allow you to select print quality, density of ink, and paper type.
36 Command summaries in each emulation mode You use software to send information and instructions to the unit over the cable that connects the unit to the computer. In addition to data, the instructions you send may include special command sequences known as control codes and ESCape sequences.
37 Using the Unit with MS-DOS Applications ESCape sequence codes (Epson LQ) Epson LQ mode command summaries You can use the control codes and ESCape sequences listed in the following table. Note: ¡ Because of hardware differences, the justification code, ESC a, and the perforation skip codes, ESC M and ESC N, are not supported.
38 Function Select vertical tab channel Set 1/8-inch line spacing (8 lpi) Set 1/6-inch line spacing (6 lpi) Set n/180-inch line spacing; n=0 to 255 Set italic mode Cancel italic mode Expand printable .
39 Using the Unit with MS-DOS Applications Function Set relative print position Set vertical tabs in channels Set 15 cpi mode Select typeface; n=type face Set left margin; n=left margin position in ch.
40 ESCape Sequence Codes (BJ) Function Select image graphics mode Set/cancel underscore mode; n=0 (End underscore), 1 (Start underscore) Set 1/8-inch line spacing (8 lpi) Set 7/72-inch line spacing (7.
41 Using the Unit with MS-DOS Applications Function Cancel super/subscript mode set by (ESC) S Set/cancel double-wide mode; n=0 (Cancel double-wide mode), 1 (Start double-wide mode) Set horizontal mar.
42 Character sets in each emulation mode Epson LQ Character Set Italic Character Set Hex No. Binary No. 0 1 2 3 4 5 6 7 8 9 A B C D E F 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100.
43 Using the Unit with MS-DOS Applications Graphic Character Set International Character Set Use the table below to replace the characters marked by the shaded areas in the Epson Italics and Graphic character sets.
44 BJ Character Set In BJ mode, the unit supports five IBM code pages: Code Page 437, Code Page 850, Code Page 860, Code Page 863, and Code Page 865. Each of the five code pages has two character sets: Set 1 and Set 2. Character Set 1 has control codes in two places: one between ASCII 0 and ASCII 32 and the other between ASCII 128 and ASCII 159.
45 Using the Unit with MS-DOS Applications Code Page 437 — Character Set 2 Code Page 850 — Character Set 1 Hex No. Binary No. 0 1 2 3 4 5 6 7 8 9 A B C D E F 0000 0001 0010 0011 0100 0101 0110 011.
46 Code Page 850 — Character Set 2 Code Page 860 — Character Set 1 Hex No. Binary No. 0 1 2 3 4 5 6 7 8 9 A B C D E F 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 111.
47 Using the Unit with MS-DOS Applications Code Page 860 — Character Set 2 Code Page 863 — Character Set 1 Hex No. Binary No. 0 1 2 3 4 5 6 7 8 9 A B C D E F 0000 0001 0010 0011 0100 0101 0110 011.
48 Code Page 863 — Character Set 2 Code Page 865 — Character Set 1 Hex No. Binary No. 0 1 2 3 4 5 6 7 8 9 A B C D E F 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 111.
49 Using the Unit with MS-DOS Applications Code Page 865 — Character Set 2 Hex No. Binary No. 0 1 2 3 4 5 6 7 8 9 A B C D E F 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 11.
50 Error messages on the display If the unit detects a problem, one of the following messages will appear on the display. CAUSE & REMEDY ERROR MESSAGE ¡ While printing, the unit ran out of recording paper. Install paper, and then press the START/SET button.
51 Troubleshooting and Routine Care PROBLEM CAUSE & REMEDY PROBLEM CAUSE & REMEDY Before requesting help The unit does not print. The unit automatically turns off the printer mode even though the connected computer is turned on. ¡ The power cord or interface cable is not connected.
52 PROBLEM CAUSE & REMEDY PROBLEM CAUSE & REMEDY The print quality is poor. Characters and images are blurred. Printed images on the transparencies are blurred. The reverse side of the printed page has smudges. White streaks or missing dots appear on printed pages.
53 Troubleshooting and Routine Care PROBLEM CAUSE & REMEDY Overall printing is slow. The unit does not print or prints garbage. “Stalled print jobs in Printer Manager” is displayed. “Remove Fast Printing Direct to Print” is displayed. You cannot print from file menu.
54 PROBLEM CAUSE & REMEDY PROBLEM CAUSE & REMEDY Overall printing is slow. Printout is wrong. Printed characters do not match characters on the screen. The unit is not using the font you selected in the MENU function. The unit prints incorrect number of lines on a page.
55 Troubleshooting and Routine Care Replacing the print and ink cartridge Replace the print cartridge when: — you have been using the cartridge for over one year, — the printing is not crisp and t.
56 5 Store or dispose of the print cartridge. ¡ If you are switching cartridges, store the cartridge you are removing in the cartridge container. 6 Unwrap the new print cartridge and remove the print head cap and the protective tape.
57 Troubleshooting and Routine Care Replacing an ink cartridge in the KX-FA151 color print cartridge Replace the ink cartridge when: — you have been using the ink cartridge for over six months, or .
58 5 Unwrap the new ink cartridge and remove the protective cap. 6 Install the new ink cartridge by A Sliding it into the empty slot on the print cartridge, and B Pressing firmly on the tab on the top of the ink cartridge until the cartridge snaps into place.
59 Troubleshooting and Routine Care Specifications Paper specifications Paper Size: Letter (8.5 wq 11 w ) Legal (8.5 wq 14 w ) A4 (210 mm q 297 mm) U.S. Commercial number 10 envelope (9.5 wq 4.1 w ) Envelope DL (220 mm q 110 mm) Paper Type: Ink jet paper (Canon Bubble Jet Paper LC-301 for BJC-4100 is recommended.
60 Printing Area — Papers: The shaded portion in the following figure shows the printing area for papers. Recommended Printing Area: Letter size a=8.5 w , b=0.25 w , c=11.0 w , d=0.83 w , e=0.81 w Legal size a=8.5 w , b=0.25 w , c=14.0 w , d=0.83 w , e=0.
61 Specifications Resident Printer Control Modes: Epson LQ mode Epson LQ-2550 emulation BJ mode IBM Proprinter X24E emulation Line Feed Pitch: Epson LQ mode 1/6 w , 1/8 w , n/180 w , and n/360 w (n: .
62 Graphic Image Print: Data Format Vertical 8, 24, and/or 48-dot format Resolution Horizontal 60, 120, 180, 240, 360, 720 dpi (in smoothing mode only) Buffer: Epson LQ mode: Input buffer 32 KB Downlo.
63 Index A About... tab RRRRRRRRRRRRR 26 AGM MODE SET RRRRRRRRR 30, 32 AUTO CR RRRRRRRRRRRR 30, 32 AUTO EMULATION SWITCH RR 30, 31, 32 Automatic halftoning RRRRRRR 19, 24 Automatic sheet feed RRRRRRR .
Matsushita Consumer Electronics Company, Division of Matsushita Electric Corporation of America One Panasonic Way, Secaucus, New Jersey 07094 Panasonic Sales Company, Division of Matsushita Electric of Puerto Rico, Inc. (“PSC”) Ave. 65 de Infantería, Km.
Ein wichtiger Punkt beim Kauf des Geräts Panasonic KX-F160 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Panasonic KX-F160 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Panasonic KX-F160 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Panasonic KX-F160 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Panasonic KX-F160 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Panasonic KX-F160 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Panasonic KX-F160 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Panasonic KX-F160. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Panasonic KX-F160 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
