Benutzeranleitung / Produktwartung HP-4800 des Produzenten Orion Car Audio
Zur Seite of 30
HP-2800 HP-4800 HP-2800 HP-4800.
CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 What’ s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION Thank you for your purchase of Orion's HP-2800, or HP-4800 power amplifier . Each Orion amplifier is designed to be the leader in its class offering the most power , advanced fea- tures, and extreme ease of use. In high-end sound systems or high SPL systems, Orion ampli- fiers will give you years of trouble-free performance.
PRACTICE SAFE SOUND™ Continuous exposure to sound pressure levels over 100dB may cause permanent hearing loss. High power automotive sound systems can generate sound pressure levels in excess of 130dB. When playing your system at high levels, please use hearing protection and avoid long term exposure.
10. Power LED - when illuminated (green) indicates that the amplifier is on. Protect LED - when illuminated (red) indicates that the amplifier protective cir- cuitry has been activated due to thermal, output short, supply undervoltage or supply overvoltage.
5 © 2005 Directed Electr onics, all rights reserved HP4800 Controls 1. Hi Input (high level input Ch 1/2 and Ch 3/4) - Accepts 1v to 10v input from the head unit’ s speaker output. The amplifier will automatically wake-up when the input is greater than 1V (on channel 1/2 high level input only).
6 © 2005 Directed Electr onics, all rights reserved HP4800 Connections 1. A TC Fuse - (2) 30-amp A TC fuses protect the amplifier against internal electrical damage and is meant to protect the amplifier only . All other power connections should be fused at the source.
7 © 2005 Directed Electr onics, all rights reserved CEA SPECIFICA TIONS H H P P - - 2 2 8 8 0 0 0 0 Power Output: 125 Watts RMS x 2 at 4 ohms and < 1% THD+N Signal to Noise Ratio: -80 dBA (reference 1 Watt into 4 ohms) Additional Power Output: 200 Watts RMS x 2 at 2 ohm at 14.
8 © 2005 Directed Electr onics, all rights reserved SPECIFICA TIONS 1. Continuous 4 W load 20Hz to 20kHz, < 1% THD, with input voltage at 14.4VDC. 2.
9 © 2005 Directed Electr onics, all rights reserved AMPLIFIER SETTINGS Signal Input and Output Configurations Depending on your model, the input section of the amplifier consists of gain controls, high pass and low pass crossovers controls, Intelli-Q control, Intelli-Bass control and RCA inputs and outputs.
10 © 2005 Directed Electr onics, all rights reserved WARNING! Exercise caution when setting INTELLi-Q. Maximum boost can potentially cause woofer damage due to over-excursion. Adjusting Intelli-Q Incorporated in the high-pass crossover , Intelli-Q maximizes the performance of a sub- woofer .
11 © 2005 Directed Electr onics, all rights reserved Infinite Baffle Example High-Pass Set at 30Hz By removing low frequency signal that the woofer cannot produce, the woofer can play its capable range louder . The first example is an infinite baffle situation.
12 © 2005 Directed Electr onics, all rights reserved Sealed Example High-Pass Set at 20Hz This sealed example is the same 12-inch woofer in the recommended sealed enclosure. Up to 6 dB of boost is capable if 20 Hz was used. With +6dB of boost, the woofer has more out- put down to 15 Hz.
13 © 2005 Directed Electr onics, all rights reserved Remote Bass Operation (optional) The remote bass port provides easy remote access to the internal gain structure of the HP power amplifier . The optional HP-RB1 plugs into the amplifier via the 1/8" mini jack plug.
14 © 2005 Directed Electr onics, all rights reserved Speaker Connections HP-2800 One Channel/T wo Channel Configuration The Orion HP-2800 amplifier offer two positive and two negative output terminals for ease of connecting channel 1 and/or 2 outputs to the speakers.
15 © 2005 Directed Electr onics, all rights reserved Three Channel (Channel 1, Channel 2, Bridged) ● Channels 1 and 2 are configured for two-channel stereo operation. ● Front channel lowest recommended impedance is 2 W stereo. ● The third output is configured for a single channel bridged output.
16 © 2005 Directed Electr onics, all rights reserved Speaker Connections HP-4800 The Orion HP-4800 amplifier offer four positive and four negative output terminals for ease of connecting channel 1, 2, 3, and 4 outputs to the speakers. The amplifier is stable to 2 W .
17 © 2005 Directed Electr onics, all rights reserved Three Channel Stereo/Bridged Configuration ● Channels 1/2 are configured for 2-channel stereo operation. ● Channel 1/2 lowest recommended impedance is 2 W stereo. ● Channels 3/4 are configured for a single channel bridged output.
18 © 2005 Directed Electr onics, all rights reserved T ri-Mode Six Channel Configuration ● Lowest recommended impedance is 2 W stereo and 4 W bridged mono. ● Front and rear outputs must be set for full range operation. ● Passive crossovers must be used on all components and frequencies must not overlap.
AMPLIFIER INST ALLA TION Choosing Mounting Locations The location of your amplifier will depend on several important issues. Due to the low pro- file size of the Orion amplifiers, there are many possible installation locations that will yield satisfactory amplifier performance.
20 © 2005 Directed Electr onics, all rights reserved Power for systems with a single amplifier can be supplied by most automotive electrical sys- tems. Systems with multiple amplifiers may require a higher capacity battery , alternator or the use of a storage capacitor .
21 © 2005 Directed Electr onics, all rights reserved Step 8 Connect power wires to the amplifier (ground first, then 12 V(+) and REM). Do not connect the battery at this time. Step 9 Connect the RCA and speaker wires to the amplifier . Check the quality of your speakers and signal connections.
22 © 2005 Directed Electr onics, all rights reserved Step 7 If the output is clear and undistorted, continue to the Adjusting the Sound of the System section of this manual. Adjusting the Sound of the System Once you have checked the system's operation, adjust the sound of the system.
23 © 2005 Directed Electr onics, all rights reserved T roubleshooting Tips Symptom Probable Cause Action T o T ake No output Low or no remote turn-on Check remote turn-on voltage at voltage amplifier and repair as needed. Fuse blown Check power wire's integrity and check for speaker shorts.
24 © 2005 Directed Electr onics, all rights reserved Symptom Probable Cause Action T o T ake Distorted output Internal crossover not set Readjust crossovers. Refer to the properly for speakers Internal Crossover Configuration section of this guide for detailed instructions.
APPENDIX—PROGRAMMABLE FEA TURES The following listing are ESP ® -2 features that can be programmed or accessed by your installer to customize or troubleshoot your system. Factory default settings are shown in bold. NOTE: The Bitwriter ® must have software version 2.
NOTE: Use caution when adjusting or unlocking gain as restricting the range or unlock- ing the range can result in sudden increases in gain. The V alet Monitoring and Anti Theft options (below) require the ESP2 alarm to be “learned” into the amplifier .
Event 1 through 7 - Stores up to seven recent events that have occurred to aid in diagnos- tic troubleshooting. The events that are retained are: Undervoltage, Overvoltage, Reserved, No Fault, Thermal, Overcurrent. These events are read-only , they and should not be be writ- ten to the amplifier by the installer .
NOTES ____________________________________________________ ____________________________________________________ ____________________________________________________ ___________________________________.
W arranty LIMITED TWO YEAR CONSUMER WARRANTY : Directed Electronics promises to the original purchaser , to replace this product should it prove to be defective in workmanship or material under normal.
Ein wichtiger Punkt beim Kauf des Geräts Orion Car Audio HP-4800 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Orion Car Audio HP-4800 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Orion Car Audio HP-4800 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Orion Car Audio HP-4800 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Orion Car Audio HP-4800 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Orion Car Audio HP-4800 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Orion Car Audio HP-4800 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Orion Car Audio HP-4800. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Orion Car Audio HP-4800 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
