Benutzeranleitung / Produktwartung Corsa (2015) des Produzenten Opel
Zur Seite of 252
OPEL CORSA Owner's Manual.
.
Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 22 Seats, restraints ........................... 36 Storage ........................................ 58 Instruments and controls .
2 Introduction Introduction.
Introduction 3 Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate.
4 Introduction 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage.
Introduction 5.
6 In brief In brief Initial drive information Vehicle unlocking Press button c to unlock the doors and load compartment. Open the doors by pulling the handles. To open the tailgate, push the touchpad switch below the brand emblem. Radio remote control 3 23, Central locking system 3 24, Load compartment 3 27.
In brief 7 Seat adjustment Seat positioning Pull handle, slide seat, release handle. Seat position 3 37, Seat adjustment 3 38. 9 Danger Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. Seat backrests Turn handwheel to adjust inclination.
8 In brief Head restraint adjustment Press release button, adjust height, engage. Head restraints 3 36. Seat belt Pull out the seat belt and engage in belt buckle. The seat belt must not be twisted and must fit close against the body. The backrest must not be tilted back too far (maximum approx.
In brief 9 Dazzle from following vehicles at night is automatically reduced. Automatic anti-dazzle interior mirror 3 31. Exterior mirrors Select the relevant exterior mirror with the rocker switch and adjust the mirror with the control : . Convex exterior mirrors 3 30, Electric adjustment 3 30, Folding exterior mirrors 3 30.
10 In brief Instrument panel overview.
.
12 In brief.
In brief 13 1 Power windows ..................... 32 2 Exterior mirrors ..................... 30 3 Cruise control ..................... 149 Speed limiter ...................... 151 Forward collision alert ........ 152 4 Turn and lane-change signals, headlight flash, low beam and high beam .
14 In brief Exterior lighting Light switch Turn light switch: 7 = lights off 8 = sidelights 9 = headlights Fog lights Press buttons in light switch > = front fog lights r = rear fog light Light swi.
In brief 15 Turn and lane-change signals lever up = right turn signal lever down = left turn signal Turn and lane-change signals 3 114, Parking lights 3 115. Hazard warning flashers Operated with the ¨ button. Hazard warning flashers 3 114. Horn Press j .
16 In brief Washer and wiper systems Windscreen wiper HI = fast LO = slow INT = interval wiping or automatic wiping with rain sensor OFF = off For single wipe when the wiper is off, press lever down to position 1x . Windscreen wiper 3 78. Windscreen washer Pull lever.
In brief 17 Rear window washer Push lever. Washer fluid is sprayed on the rear window and the wiper wipes a few times. Rear window wiper/washer 3 79. Climate control Heated rear window The heating is operated by pressing the Ü button. Heated rear window 3 33, heated windscreen 3 33.
18 In brief Transmission Manual transmission Reverse: with the vehicle stationary, depress clutch pedal and press the release button on the selector lever and engage the gear. If the gear does not engage, set the lever to neutral, release the clutch pedal and depress again; then repeat gear selection.
In brief 19 Starting off Check before starting off ■ Tyre pressure and condition 3 201, 3 240. ■ Engine oil level and fluid levels 3 180. ■ All windows, mirrors, exterior lighting and number plates are free from dirt, snow and ice and are operational.
20 In brief Stop-start system If the vehicle is at a low speed or at a standstill and certain conditions are fulfilled, activate an Autostop as follows: Vehicles with manual transmission ■ Depress the clutch pedal. ■ Set the lever in neutral. ■ Release the clutch pedal.
In brief 21 P before removing the ignition key. Turn the front wheels towards the kerb. ■ Close the windows and the sunroof. ■ Remove the ignition key. Turn the steering wheel until the steering wheel lock is felt to engage. For vehicles with automatic transmission, the key can only be removed when the selector lever is in position P .
22 Keys, doors and windows Keys, doors and windows Keys, locks ................................... 22 Doors ........................................... 27 Vehicle security ............................ 28 Exterior mirrors ............................ 30 Interior mirrors .
Keys, doors and windows 23 Radio remote control Used to operate: ■ central locking system ■ anti-theft locking system ■ anti-theft alarm system The radio remote control has a range of approx. 20 metres. It can be restricted by external influences.
24 Keys, doors and windows Radio remote control synchronisation After replacing the battery, unlock the door with the key in the driver's door lock.
Keys, doors and windows 25 Memorised settings 3 24. Unlocking and opening the tailgate 3 27. Locking Close doors, load compartment and fuel filler flap. Press button e . If the driver's door is not closed properly, the central locking system will not work.
26 Keys, doors and windows Locking Manually lock the driver's door by turning the key in the lock. Fault in central locking system Unlocking Manually unlock the driver's door by turning the key in the lock. The other doors can be opened by pulling the interior handle twice.
Keys, doors and windows 27 Doors Load compartment Tailgate Opening To open the tailgate, push the touchpad switch below the brand emblem. Closing Use interior handle. Do not press the touchpad switch whilst closing as this will unlock the tailgate again.
28 Keys, doors and windows Vehicle security Anti-theft locking system 9 Warning Do not use the system if there are people in the vehicle! The doors cannot be unlocked from the inside. The system deadlocks all the doors. All doors must be closed otherwise the system cannot be activated.
Keys, doors and windows 29 Status during the first 30 seconds of anti-theft alarm system activation: LED illuminates = test, arming delay LED flashes quickly = doors, tailgate or bonnet not completely closed, or system fault Status after system is armed: LED flashes slowly = system is armed Seek the assistance of a workshop in the event of faults.
30 Keys, doors and windows Exterior mirrors Convex shape The convex exterior mirror contains an aspherical area and reduces blind spots. The shape of the mirror makes objects appear smaller, which will affect the ability to estimate distances.
Keys, doors and windows 31 Interior mirrors Manual anti-dazzle To reduce dazzle, adjust the lever on the underside of the mirror housing. Automatic anti-dazzle Dazzle from following vehicles at night is automatically reduced. Windows Windscreen Windscreen stickers Do not attach stickers, e.
32 Keys, doors and windows Power windows 9 Warning Take care when operating the power windows. Risk of injury, particularly to children. Be careful when closing the windows. Ensure that nothing becomes trapped in them as they move. Operable with ignition on (position 2 ) 3 131.
Keys, doors and windows 33 Heated rear window Operated by pressing button Ü . Rear window heating works with the engine running. It is switched off automatically after six minutes. Pressing button Ü once more during the same ignition cycle allows the heating to operate for another three minutes.
34 Keys, doors and windows Roof Sunroof 9 Warning Take care when operating the sunroof. Risk of injury, particularly to children. Keep a close watch on the movable parts when operating them. Ensure that nothing becomes trapped in them as they move. Operable via a rocker switch with ignition on (position 2 ) 3 131.
Keys, doors and windows 35 Overload If the system is overloaded, the power supply is automatically cut-off for a short time. The system is protected by fuses in the fuse box 3 194.
36 Seats, restraints Seats, restraints Head restraints ............................ 36 Front seats ................................... 37 Seat belts ..................................... 40 Airbag system .............................. 43 Child restraints .
Seats, restraints 37 Rear head restraints, height adjustment Pull the head restraint upwards and let engage. To move downwards, press the catch to release and push the head restraint downwards. Removal of rear head restraint E.g. when using a child restraint system 3 50.
38 Seats, restraints ■ Sit with shoulders as far back against the backrest as possible. Set the backrest rake so that it is possible to easily reach the steering wheel with arms slightly bent. Maintain contact between shoulders and the backrest when turning the steering wheel.
Seats, restraints 39 Seat backrests Turn handwheel to adjust inclination. Do not lean on backrest while adjusting. Seat height Lever pumping motion up = seat higher down = seat lower Seat folding Pull release lever towards the front and fold backrest forwards.
40 Seats, restraints Caution When seat height is in the highest position, push head restraints down and fold up sun visors before folding backrest forwards. Heating Activate seat heating by pressing ß button for the respective front seat. Activation is indicated by the LED in the button.
Seats, restraints 41 Seat belts are designed to be used by only one person at a time. Child restraint system 3 50. Periodically check all parts of the belt system for damage, pollution and proper functionality. Have damaged components replaced. After an accident, have the belts and triggered belt pretensioners replaced by a workshop.
42 Seats, restraints Loose or bulky clothing prevents the belt from fitting snugly. Do not place objects such as handbags or mobile phones between the belt and your body. 9 Warning The belt must not rest against hard or fragile objects in the pockets of your clothing.
Seats, restraints 43 Removing To release belt, press red button on belt buckle. Using the seat belt while pregnant 9 Warning The lap belt must be positioned as low as possible across the pelvis to prevent pressure on the abdomen. Airbag system The airbag system consists of a number of individual systems depending on the scope of equipment.
44 Seats, restraints Each airbag is triggered only once. Have deployed airbags replaced by a workshop. Furthermore, it may be necessary to have the steering wheel, the instrument panel, parts of the panelling, the door seals, handles and the seats replaced.
Seats, restraints 45 DA: Brug ALDRIG en bagudvendt autostol på et forsæde med AKTIV AIRBAG, BARNET kan komme i LIVSFARE eller komme ALVORLIGT TIL SKADE. SV: Använd ALDRIG en bakåtvänd barnstol på ett säte som skyddas med en framförvarande AKTIV AIRBAG.
46 Seats, restraints BLAZINO, saj pri tem obstaja nevarnost RESNIH ali SMRTNIH POŠKODB za OTROKA. SR: NIKADA ne koristiti bezbednosni sistem za decu u kome su deca okrenuta unazad na sedištu sa AKTIVNIM VAZDUŠNIM JASTUKOM ispred sedišta zato što DETE može da NASTRADA ili da se TEŠKO POVREDI.
Seats, restraints 47 The front airbag system is triggered in the event of a front-end impact of a certain severity. The ignition must be switched on. The inflated airbags cushion the impact, thereby reducing the risk of injury to the upper body and head of the front seat occupants considerably.
48 Seats, restraints The inflated airbags cushion the impact, thereby reducing the risk of injury to the upper body and pelvis in the event of a side-on collision considerably. 9 Warning Keep the area in which the airbag inflates clear of obstructions.
Seats, restraints 49 Use the ignition key to choose the switch position: * OFF = front passenger airbag is deactivated and will not inflate in the event of a collision.
50 Seats, restraints Child restraints Child restraint systems We recommend Opel child restraint systems which are tailored specifically to the vehicle.
Seats, restraints 51 Note Do not affix anything on the child restraint systems and do not cover them with any other materials. A child restraint system which has been subjected to stress in an accident must be replaced.
52 Seats, restraints Child restraint installation locations Permissible options for fastening a child restraint system with a three-point seat belt Weight and age class On front passenger seat On rear outboard seats On rear centre seat activated airbag deactivated airbag Group 0: up to 10 kg or approx.
Seats, restraints 53 2 = move seat height adjustment upwards as far as necessary and adjust seat backrest inclination as far as necessary to a vertical position to ensure that the belt is tight on the.
54 Seats, restraints Weight class Size class Fixture On front passenger seat 5 On rear outboard seats On rear centre seat activated airbag deactivated airbag Group II: 15 to 25 kg or approx. 3 to 7 years IL 1,2 X IL 3,4 X Group III: 22 to 36 kg or approx.
Seats, restraints 55 ISOFIX size class and seat device A – ISO/F3 = forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg B – ISO/F2 = forward-facing ch.
56 Seats, restraints ISOFIX child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. Specific vehicle ISOFIX child restraint system positions are marked in the table by IL. The vehicle is equipped with guides in the backrests to support the installation of the child restraint system.
Seats, restraints 57 Top-tether fastening eye on front passenger seat An additional fastening point is located on the passenger seat rail in the rear foot well.
58 Storage Storage Storage compartments ................ 58 Load compartment ....................... 69 Roof rack system ......................... 73 Loading information ..................... 74 Storage compartments 9 Warning Do not store heavy or sharp objects in the storage compartments.
Storage 59 The pockets in the doors are designed to carry bottles. Additional bottleholders are located in the rear side panels. Flexible cupholder strap A movable rubber strap is located in the storage compartment in front of the gear selector lever.
60 Storage Underseat storage Lift at recessed edge and pull out. Maximum load: 1.5 kg. To close, push in and engage. Rear carrier system The rear carrier system (Flex-Fix system) allows bicycles to be attached to a pull-out carrier integrated into the vehicle floor.
Storage 61 Pull release lever up. The system disengages and travels quickly out of the bumper. Completely pull out the rear carrier system until you hear it engage. Ensure that it is not possible to push in the rear carrier system without pulling the release lever again.
62 Storage Open out the lamp support on the back of the tail lamp completely until it engages. Push the clamping lever down and push the lamp support into the retainer until it engages. Perform this procedure for both tail lamps. Check the cable and lamp position to make sure these are correctly installed and are securely located.
Storage 63 Unfold pedal crank recesses Fold one or both pedal crank recesses upwards until the diagonal support engages. Remove the pedal crank mounts from the pedal crank recesses. Adapting the rear carrier system to a bicycle Press the release lever and withdraw the wheel recesses.
64 Storage Push the release lever on the strap retainer and remove the strap retainer. Prepare the bicycle for attachment Note The maximum width for the pedal crank is 38.3 mm and the maximum depth is 14.4 mm. Rotate the left pedal (without a chain cog) vertically downwards.
Storage 65 If the bicycle has curved pedal cranks, screw in the pedal crank unit all the way (position 1 ). Put on the bicycle. The pedal crank here must be placed in the pedal crank recess opening as shown in the illustration. Caution Make sure that the pedal does not touch the surface of the rear end carrier.
66 Storage Place the wheel recesses so that the bicycle is roughly horizontal. Here, the distance between the pedals and the tailgate should be at least 5 cm. Both bicycle tyres must be in the wheel recesses. Caution Make sure to pull out the wheel recesses as far as necessary to have both bicycle tyres placed in the recesses.
Storage 67 The settings for the wheel recesses and on the rotary lever on the pedal crank recess should be noted and saved for each bicycle. Correct presetting will facilitate refitting of the bicycle. Note It is recommended to attach a warning sign at the rearmost bicycle to increase visibility.
68 Storage Press release lever and slide in wheel recesses all the way as far as they will go. Disengage the locking lever on the diagonal support and fold both pedal crank recesses down.
Storage 69 Push the release lever up and hold. Lift the system slightly and push it into the bumper until it engages. Release lever must return to original position. 9 Warning If the system cannot be correctly engaged, please seek the assistance of a workshop.
70 Storage Guide the seat belts through side supports to protect them against damage. When folding the backrest, pull the seat belts along with it. Split backrest Pull the release handle on the relevant side and fold it down onto the seat cushion. Single-unit backrest Pull the release handle on both sides and fold it down onto the seat cushion.
Storage 71 Load compartment cover Do not place any objects on the cover. Removing Unhook retaining straps from tailgate. Lift cover at the rear and push it upwards at the front. Remove the cover. Stowing When the load compartment is fully loaded, stow the load compartment cover on the rear seats or remove from vehicle.
72 Storage To insert, push the load-bay floor forwards in the corresponding guide, then lower. If mounted in the upper position, the space between the load-bay floor and the spare wheel well cover can be used as a stowage compartment. In this position, if the rear seat backrests are folded forwards, an almost completely flat load bay is created.
Storage 73 First aid kit Stow the first-aid kit in the compartment in the left wall of the load compartment. To open the compartment, disengage cover and open it. Roof rack system Roof rack For safety reasons and to avoid damage to the roof, the vehicle approved roof rack system is recommended.
74 Storage Loading information ■ Heavy objects in the load compartment should be placed against the seat backrests. Ensure that the backrests are securely engaged. If objects can be stacked, heavier objects should be placed at the bottom. ■ Secure objects with lashing straps attached to the lashing eyes 3 72.
Storage 75 the vehicle's higher centre of gravity. Distribute the load evenly and secure it properly with retaining straps. Adjust the tyre pressure and vehicle speed according to the load conditions. Check and retighten the straps frequently. Do not drive faster than 120 km/h.
76 Instruments and controls Instruments and controls Controls ....................................... 76 Warning lights, gauges and indi‐ cators ........................................... 84 Information displays ..................... 95 Vehicle messages .
Instruments and controls 77 Heated steering wheel Activate heating by pressing * button. Activation is indicated by the LED in the button. The highlighted grip areas of the steering wheel are heated quicker and to a higher temperature than the other areas.
78 Instruments and controls Windscreen wiper/washer Windscreen wiper HI = fast LO = slow INT = interval wiping or automatic wiping with rain sensor OFF = off For a single wipe when the windscreen wiper is off, press the lever down to position 1x . Do not use if the windscreen is frozen.
Instruments and controls 79 Adjustable sensitivity of the rain sensor Turn the adjuster wheel to adjust the sensitivity: low sensitivity = turn adjuster wheel downwards high sensitivity = turn adjuster wheel upwards Keep the sensor free from dust, dirt and ice.
80 Instruments and controls Push lever. Washer fluid is sprayed onto the rear window and the wiper wipes a few times. Do not use if the rear window is frozen. Switch off in car washes. The rear window wiper comes on automatically when the windscreen wiper is switched on and reverse gear is engaged.
Instruments and controls 81 If outside temperature drops to 3 °C, a warning message is displayed in the Driver Information Centre. 9 Warning The road surface may already be icy even though the display indicates a few degrees above 0 °C. Clock Graphic-Info Display Press the CONFIG button to open the Settings menu.
82 Instruments and controls Set date format To switch between the available options, repeatedly press the MENU-TUNE knob. RDS clock synchronization The RDS signal of most VHF transmitters automatically sets the time. RDS time synchronisation can take a few minutes.
Instruments and controls 83 Power outlets A 12 Volt power outlet is located in the centre console. Do not exceed the maximum power consumption of 120 watts. With ignition off, the power outlet is deactivated. Additionally, the power outlet is deactivated in the event of low vehicle battery voltage.
84 Instruments and controls Warning lights, gauges and indicators Instrument cluster The needles of the instruments briefly rotate to the end position when the ignition is switched on. Speedometer Indicates vehicle speed. Odometer The bottom line displays the recorded distance in km.
Instruments and controls 85 Uplevel display Two trip odometer are selectable for different trips. Select page Trip by pressing Menu button on the turn signal lever.
86 Instruments and controls Engine coolant temperature gauge Number of LEDs displays the coolant temperature. up to 3 LEDs = engine operating temperature not yet reached 4 to 6 LEDs = normal operating temperature more than 6 LEDs = temperature too high Caution If engine coolant temperature is too high, stop vehicle, switch off engine.
Instruments and controls 87 The remaining engine oil life duration is displayed in percent in the Driver Information Centre. Reset Press the SET/CLR button on turn signal lever for several seconds to reset. The remaining engine oil life duration page must be active.
88 Instruments and controls Control indicators in the instrument cluster.
Instruments and controls 89 Control indicators in the centre console Turn signal O illuminates or flashes green. Illuminates briefly The parking lights are switched on. Flashes A turn signal or the hazard warning flashers are activated. Rapid flashing: failure of a turn signal light or associated fuse.
90 Instruments and controls Illuminates After having started the engine for a minimum of 35 seconds, until the seat belt has been fastened. If an unfastened seat belt is fastened whilst driving. Flashes After starting-off, when the seat belt is unfastened.
Instruments and controls 91 Illuminates when the engine is running Fault in the emission control system. The permitted emission limits may be exceeded. Seek the assistance of a workshop immediately. Flashes when the engine is running Fault that could lead to catalytic converter damage.
92 Instruments and controls Illuminates with power steering reduced Power steering is reduced due to overheating of the system. Control indicator extinguishes when the system has cooled down. Stop-start system 3 133. Illuminates with power steering disabled Failure in the power steering system.
Instruments and controls 93 Diesel particle filter % illuminates or flashes yellow. The diesel particle filter requires cleaning. Continue driving until % extinguishes. If possible, do not allow engine speed to drop below 2000 rpm. Illuminates The diesel particle filter is full.
94 Instruments and controls Do not remove key until vehicle is stationary, otherwise the steering wheel lock could engage unexpectedly. Check oil level before seeking the assistance of a workshop 3 180. Low fuel Y illuminates or flashes yellow. Illuminates Level in fuel tank is too low.
Instruments and controls 95 A vehicle ahead is detected in the same lane. Forward collision alert 3 152. Speed limiter L illuminates in the Driver Information Centre when Speed limiter is active. Set speed is indicated near L symbol. Speed limiter 3 151.
96 Instruments and controls ■ language setting, if no Infotainment system available ■ clock, if no Infotainment system available ■ outside temperature, if no Infotainment system available Some of the displayed functions differ when the vehicle is being driven or at a standstill.
Instruments and controls 97 Press the MENU button to switch between the main menus or to return from a submenu to the next higher menu level. Turn the adjuster wheel to select a subpage of the main menu or to set a numeric value. Press the SET/CLR button to select and confirm a function.
98 Instruments and controls Simultaneously trip odometer 1 and 2 is indicated together with average fuel economy 1 and 2. The information of trip page 1 and 2 can be reset separately while the respective display is active. Digital speed Digital display of the instantaneous speed.
Instruments and controls 99 Unit Press SET/CLR while page is displayed. Select imperial (unit 1) or metric (unit 3) by turning the adjuster wheel. Press SET/CLR to set the unit. Speed warning The speed warning function alarms when a set speed is exceeded.
100 Instruments and controls Filled segments display the consumption in 5 km steps and shows the effect of topography or driving behaviour on fuel consumption. Graph can be reset by pressing SET/CLR button. Fuel Economy Indicates the average fuel consumption since the last driver reset compared to a best average fuel consumption value.
Instruments and controls 101 Selecting menus and settings Menus and settings are selected via the touch screen display. Press button ; : Home page is displayed. Tap display icon Settings : Menu page Settings is displayed. Select a setting by tapping. Tap selection once more to confirm a setting or value.
102 Instruments and controls Press button BACK to exit a menu or setting without changing or delete the last character in a character sequence. Press the button for a few seconds to delete the entire entry. To exit the Settings menu, press button BACK in steps or press button CONFIG after confirming the changes.
Instruments and controls 103 No. Vehicle message 9 Turn steering wheel, start engine again 12 Vehicle overloaded 13 Compressor overheated 15 Centre high-mounted brake light failure 16 Brake light fail.
104 Instruments and controls No. Vehicle message 82 Change engine oil soon 84 Engine power reduced 89 Service vehicle soon 94 Shift to park before exiting 95 Service airbag 128 Bonnet open 134 Park as.
Instruments and controls 105 ■ If a warning message appears in the Driver Information Centre or Info-Display. ■ If the parking assist detects an object. ■ If unintended lane change occurs. ■ If the reverse gear is engaged and the rear end carrier extended.
106 Instruments and controls The following settings can be selected: ■ Languages ■ Time Date ■ Radio settings ■ Phone settings ■ Vehicle settings In the corresponding submenus, the following settings can be changed: Languages Selection of the desired language.
Instruments and controls 107 Activates or deactivates the entry lighting. Duration upon exit of vehicle : Activates or deactivates and changes the duration of exit lighting. ■ Power door locks Auto door lock : Activates or deactivates the automatic door locking function after switching on ignition.
108 Instruments and controls ■ Time & date settings ■ Radio settings ■ Connection settings ■ Vehicle settings ■ Language ■ Text scroll ■ Touch beep volume ■ Max startup volume ■ System version ■ DivX(R) VOD In the corresponding submenus the following settings can be changed: Time & date settings See Clock 3 81.
Instruments and controls 109 Unlocked door anti lock out : Activates or deactivates the door locking function while a door is open. Delayed door lock : Activates or deactivates the delayed door locking function. This menu option is displayed with Unlocked door anti lock out deactivated.
110 Lighting Lighting Exterior lighting .......................... 110 Interior lighting ........................... 116 Lighting features ........................ 118 Exterior lighting Light switch Turn light switch: 7 = lights off 8 = sidelights 9 = headlights Control indicator 8 3 94.
Lighting 111 The current status of the automatic light control is displayed In the Driver Information Centre. When switching on the ignition, automatic light control is active. When headlights are on, 8 illuminates. Control indicator 8 3 94. Tail lights Tail lights are illuminated together with headlights and sidelights.
112 Lighting Headlight range adjustment Manual headlight range adjustment To adapt headlight range to the vehicle load to prevent dazzling: turn thumb wheel ? to required position.
Lighting 113 Xenon lighting system Xenon lighting system includes ■ xenon headlights for low and high beam ■ high beam assist ■ corner lighting ■ reversing function Xenon headlights Xenon headlights for low and high beam ensure better visibility under all conditions.
114 Lighting Corner lighting On tight bends or when turning off, depending on the steering angle or the indicator light signal, an additional left or right reflector is switched on which illuminates the road in the direction of travel. It is activated up to a speed of 40 km/h.
Lighting 115 With a trailer connected, turn signal flashes six times when pressing the lever until resistance is felt and then releasing. Move the lever to the resistance point and hold for longer indication. Switch the turn signal off manually by moving the lever to its original position.
116 Lighting Reversing lights The reversing light comes on when the ignition is on and reverse gear is selected. Misted light covers The inside of the light housing may mist up briefly in poor, wet and cold weather conditions, in heavy rain or after washing.
Lighting 117 Operate rocker switch: centre position w = automatic switching on when opening a door. Turns off with delay press I = permanent on press 0 = permanent off Front courtesy light with reading lights When opening a door, the courtesy light automatically switches on and then off after a delay.
118 Lighting Reading lights Operated with 2 buttons for left and right side. Lighting features Entry lighting Welcome lighting The following lights are switched on for a short time by unlocking the ve.
Lighting 119 Activating 1. Switch off the ignition. 2. Remove the ignition key. 3. Open driver's door. 4. Pull the turn signal lever. 5. Close the driver's door If the driver's door is not closed the lights switch off after two minutes.
120 Climate control Climate control Climate control systems ............. 120 Air vents ..................................... 128 Maintenance .............................. 128 Climate control systems Heating and ventilation system Controls for: ■ temperature ■ fan speed ■ air distribution Heated rear window Ü 3 33.
Climate control 121 Demisting and defrosting the windows ■ Set temperature control to warmest level. ■ Set fan speed to highest speed. ■ Set air distribution control to l . ■ Switch on heated rear window Ü . ■ Open side air vents as required and direct them towards door windows.
122 Climate control Cooling n Press button n to switch on cooling. Activation is indicated by illumination of the LED in the button. Cooling is only functional when the engine is running and climate control fan is switched on. Press button n again to switch off cooling.
Climate control 123 ■ Switch on cooling n . ■ Air recirculation system 4 on. ■ Set temperature control to coldest level. ■ Set fan speed to highest level. ■ Set air distribution control to M . ■ Open all vents. Demisting and defrosting the windows l ■ Set temperature control to warmest level.
124 Climate control Controls for: ■ Fan speed ■ Temperature ■ Air distribution n = Cooling AUTO = Automatic mode 4 = Manual air recirculation V = Demisting and defrosting Ü = Heated rear window 3 33 Heated seats ß 3 40. Heated steering wheel * 3 77.
Climate control 125 If the minimum temperature Lo is set, the climate control system runs at maximum cooling, if cooling n is switched on. If the maximum temperature Hi is set, the climate control system runs at maximum heating.
126 Climate control Manual settings Climate control system settings can be changed by activating the buttons and rotary knobs as follows. Changing a setting will deactivate the Automatic mode. Fan speed Z Turn left rotary knob to decrease or increase fan speed.
Climate control 127 the freezing point. Therefore condensation may form and drip from under the vehicle. If no cooling or drying is required, switch off the cooling system for fuel saving reasons. When the cooling system is switched off, no engine restart will be requested by the climate control system during an Autostop.
128 Climate control Air vents Adjustable air vents At least one air vent must be open while the cooling is on. Adjust the air amount at the vent outlet by turning the adjuster wheel. The vent is closed when the adjuster wheel is turned close to the left or right.
Climate control 129 Air conditioning regular operation In order to ensure continuously efficient performance, cooling must be operated for a few minutes once a month, irrespective of the weather and time of year. Operation with cooling is not possible when the outside temperature is too low.
130 Driving and operating Driving and operating Driving hints ............................... 130 Starting and operating ............... 131 Engine exhaust .......................... 136 Automatic transmission .............. 138 Manual transmission ..
Driving and operating 131 Starting and operating New vehicle running-in Do not brake unnecessarily hard for the first few journeys. During the first drive, smoke may occur because of wax and oil evaporating off the exhaust system. Park the vehicle in the open for a while after the first drive and avoid inhaling the fumes.
132 Driving and operating Starting the engine Turn key to position 1 to release the steering wheel lock. Manual transmission: operate clutch and brake pedal. Manual transmission automated: operate brake pedal. Automatic transmission: operate brake pedal and move selector lever to P or N .
Driving and operating 133 Turbo engine warm-up Upon start-up, engine available torque may be limited for a short time, especially when the engine temperature is cold. The limitation is to allow the lubrication system to fully protect the engine. Overrun cut-off The fuel supply is automatically cut- off during overrun, i.
134 Driving and operating Indication An Autostop is indicated by the Control indicator D . During an Autostop, the heating and brake performance will be maintained. Conditions for an Autostop The stop-start system checks if each of the following conditions is fulfilled: ■ The stop-start system is not manually deactivated.
Driving and operating 135 Vehicles with manual transmission automated Release the brake pedal or move selector lever out of D to restart the engine. When the engine is restarted, the control indicator D in the DIC extinguishes. Restart of the engine by the stop-start system The selector lever must be in neutral to enable an automatic restart.
136 Driving and operating be removed when the selector lever is in position P . For vehicles with manual transmission automated, the key can only be removed from the ignition switch when the park brake is applied. ■ Lock the vehicle. ■ Activate the anti-theft alarm system.
Driving and operating 137 take up to 25 minutes. Typically it needs between seven and 12 minutes. Autostop is not available and fuel consumption may be higher during this period. The emission of smells and smoke during this process is normal. Under certain driving conditions, e.
138 Driving and operating Automatic transmission The automatic transmission permits automatic gearshifting (automatic mode) or manual gearshifting (manual mode). Manual shifting is possible in manual mode by pressing button < or ] on the selector lever 3 139.
Driving and operating 139 Without brake pedal applied, the control indicator j illuminates. If the selector lever is not in P when the ignition is switched off, the control indicator j flashes. To engage P , R or M , press the release button. The engine can only be started with the lever in position P or N .
140 Driving and operating Electronic driving programmes ■ Following a cold start, the operating temperature programme increases engine speed to quickly bring the catalytic converter to the required temperature.
Driving and operating 141 3. Push down the release lever and move the selector lever out of P or N . If these positions are engaged again, the selector lever will be locked in position again. Have the cause of the power supply interruption remedied by a workshop.
142 Driving and operating Manual transmission automated The automated manual transmission permits manual gearshifting (manual mode) or automatic gearshifting (automatic mode), both with automatic clutch control. Manual shifting is possible by tapping the selector lever in manual mode 3 139.
Driving and operating 143 An Autostop is indicated by the Control indicator D . Autostart Release the brake pedal or move selector lever out of D to restart the engine. When the engine is restarted, the control indicator D in the DIC extinguishes. The stop-start system will be disabled on inclines of 15 % or more.
144 Driving and operating Rocking the vehicle Rocking the vehicle is only permissible if the vehicle is stuck in sand, mud or snow. Move the selector lever between R and D in a repeat pattern.
Driving and operating 145 Kickdown If the accelerator pedal is pressed down completely in automatic mode, the transmission shifts to a lower gear depending on engine speed. Fault To prevent damage to the manual transmission automated, the clutch is engaged automatically at high clutch temperatures.
146 Driving and operating Fault 9 Warning If there is a fault in the ABS, the wheels may be liable to lock due to braking that is heavier than normal. The advantages of ABS are no longer available. During hard braking, the vehicle can no longer be steered and may swerve.
Driving and operating 147 soon as the vehicle begins to accelerate or the two seconds holding time is over. The hill start assist is not active during an Autostop. Ride control systems Traction Control system The Traction Control system (TC) is a component of the Electronic Stability Control (ESC).
148 Driving and operating spinning. ESC operates in combination with the Traction Control system (TC). As soon as the vehicle starts to swerve (understeer/oversteer), engine output is reduced and the wheels are braked individually. This considerably improves the driving stability of the vehicle on slippery road surfaces.
Driving and operating 149 Stop-start system 3 133. Deactivation Press button B ; LED in the button extinguishes and a message pops-up in the Driver Information Centre. Each time the engine is started, City mode is deactivated. Overload If the steering in City mode is heavily loaded, e.
150 Driving and operating For safety reasons, the cruise control cannot be activated until the foot brake has been operated once. Activating in first gear is not possible. Do not use the cruise control if it is not advisable to maintain a constant speed.
Driving and operating 151 Deactivation Press button y , control indicator m in instrument cluster illuminates white. Cruise control is deactivated. Last used set speed is stored in memory for later speed resume. Automatic deactivation: ■ Vehicle speed is below approx.
152 Driving and operating maximum speed. Speed limit is displayed in the Driver Information Centre. Change speed limit With speed limiter active, turn thumb wheel to RES/+ to increase or SET/- to decrease the desired maximum speed.
Driving and operating 153 Activation Forward collision alert operates automatically above 40 km/h, if it is not deactivated by button V , see below. Selecting the alert sensitivity The alert sensitivity can be set to near, medium or far. Press button V , the current setting is shown on the Driver Information Centre.
154 Driving and operating General information 9 Warning Forward collision alert is just a warning system and does not apply the brakes. When approaching a vehicle ahead too rapidly, it may not provide you enough time to avoid a collision.
Driving and operating 155 If there is no vehicle ahead or the vehicle ahead is out of range, two dashes will be displayed: -.- s. Parking assist Rear parking assist 9 Warning It is the driver who bears full responsibility for the parking manoeuvre. Always check the surrounding area while reversing and using the rear parking assist system.
156 Driving and operating Deactivation The system automatically switches off when reverse gear is disengaged. Manual deactivation is also possible by pressing the parking assist button r . In both cases the LED in the button extinguishes. Fault In the event of a fault or if the system does not work temporarily, e.
Driving and operating 157 Vehicles with rear or front-rear parking assist are equipped with button r . Vehicles with front-rear parking assist and advanced parking assist are recognisable by button D .
158 Driving and operating The distance to a front and rear obstacle is displayed by changing distance lines in the Driver Information Centre. The distance indication can be inhibited by vehicle messages with a higher priority. After approving the message by pressing the SET/CLR button on the turn signal lever, distance indication appears again.
Driving and operating 159 Advanced parking assist is always combined with front-rear parking assist, see previous section. Both systems use the same sensors in the front and rear bumper.
160 Driving and operating The system can only be activated at a speed up to 30 km/h and the system searches for a parking slot at a speed up to 30 km/h. The maximum allowed parallel distance between the vehicle and a row of parked cars is 1.8 metres for parallel parking and 2.
Driving and operating 161 When a slot is detected, a visual feedback on the Colour-Info-Display and an acoustic signal is given. If the driver does not stop the vehicle within 10 metres for parallel p.
162 Driving and operating ■ the successful parking indicated by a pop-up symbol and a chime ■ the cancelling of a parking manoeuvre Display priorities Advanced parking assist indication on the Driver Information Centre can be inhibited by vehicle messages with a higher priority.
Driving and operating 163 Special conditions apply if there are taller vehicles in the vicinity (e.g. off-road vehicles, mini vans, vans). Object identification and correct distance indication in the upper part of these vehicles cannot be guaranteed. Objects with a very small reflection cross-section, e.
164 Driving and operating ■ vehicles outside the side blind zones which may be rapidly approaching ■ pedestrians, cyclists or animals Before changing a lane, always check all mirrors, look over the shoulder and use the turn signal.
Driving and operating 165 dirt, snow, ice, slush, or in heavy rainstorms. Cleaning instructions 3 221. In the event of a fault in the system or if the system does not work due to temporary conditions, a message is displayed in the Driver Information Centre.
166 Driving and operating Deactivation The camera is deactivated when a certain forward speed is exceeded or if reverse gear is not engaged for approx. 10 seconds. Activation or deactivation of the visual guiding lines and the alerting symbols can be changed in the Settings menu in the Info-Display.
Driving and operating 167 Combinations of multiple signs in the display are possible. An exclamation mark in a frame indicates that there is an additional sign detected which cannot be recognised by the system. The system is active up to a speed of 200 km/h depending on the lighting conditions.
168 Driving and operating The alert function can be activated or deactivated in the setting menu of the traffic sign assistant page by pressing the SET/CLR button on the turn signal lever. Once setting page is displayed, select Alert ON to activate pop-up alert.
Driving and operating 169 event, No Traffic Sign Detection due to Weather is indicated on the display. ■ Traffic signs are incorrectly mounted or damaged. ■ Traffic signs do not comply with the Vienna Convention on traffic signs (Wiener Übereinkommen über Straßenverkehrszeichen).
170 Driving and operating When the system recognises an unintended lane change, the control indicator ) changes to yellow and flashes. Simultaneously a chime sound is activated. Deactivation The system is deactivated by pressing ) button, the LED in the button extinguishes.
Driving and operating 171 Caution Use of fuel that does not comply to EN 228 or E DIN 51626-1 or equivalent can lead to deposits or engine damage and may affect your warranty. Caution Use of fuel with too low an octane rating could lead to uncontrolled combustion and engine damage.
172 Driving and operating The fuel filler flap can only be opened if the vehicle is unlocked. Release the fuel filler flap by pushing the flap. To open, turn the cap slowly to the left. The fuel filler cap can be retained in the bracket on the fuel filler flap.
Driving and operating 173 No. 715/2007 (in the latest applicable version), taking into consideration the vehicle weight in running order, as specified by the regulation.
174 Driving and operating The permitted trailer loads apply up to the specified incline and up to an altitude of 1000 metres above sea level. Since engine power decreases as altitude increases due to .
Driving and operating 175 Fitting the coupling ball bar Disengage and fold down the socket. Remove the sealing plug from the opening for the coupling ball bar and stow it. Checking the tensioning of the coupling ball bar ■ The rotary knob rests on the coupling ball bar.
176 Driving and operating Inserting the coupling ball bar Insert the tensioned coupling ball bar in the opening and push firmly upwards until it audibly engages. The rotary knob snaps back into its original position resting against the coupling ball bar without a gap.
Driving and operating 177 9 Warning Towing a trailer is permitted only when a coupling ball bar is fitted correctly. If the coupling ball bar does not engage correctly, seek the assistance of a workshop. Dismounting the coupling ball bar Insert the key in the lock and unlock the coupling ball bar.
178 Vehicle care Vehicle care General Information ................... 178 Vehicle checks ........................... 179 Bulb replacement ....................... 186 Electrical system ........................ 194 Vehicle tools ........................
Vehicle care 179 ■ Open the bonnet, close all doors and lock the vehicle. ■ Disconnect the clamp from the negative terminal of the vehicle battery.
180 Vehicle care 9 Danger The ignition system and Xenon headlights use extremely high voltage. Do not touch. Bonnet Opening Pull the release lever and return it to its original position. Push the safety catch upwards and open the bonnet. Secure the bonnet support.
Vehicle care 181 Pull out the dipstick, wipe it clean, insert it to the stop on the handle, pull out and read the engine oil level. Insert dipstick to the stop on the handle and make half a turn. Different dipsticks are used depending on engine variant.
182 Vehicle care Engine coolant The coolant provides freeze protection down to approx. -28 °C. In northern countries with very low temperatures the factory filled coolant provides frost protection down to approx. -37 °C. Caution Only use approved antifreeze.
Vehicle care 183 Washer fluid Fill with clean water mixed with a suitable quantity of windscreen washer fluid which contains antifreeze. Caution Only washer fluid with a sufficient antifreeze concentration provides protection at low temperatures or a sudden drop in temperature.
184 Vehicle care battery. Short-distance-driving and frequent engine starts can discharge the vehicle battery. Avoid the use of unnecessary electrical consumers. Batteries do not belong in household waste. They must be disposed of at an appropriate recycling collection point.
Vehicle care 185 Charging the vehicle battery 9 Warning On vehicles with stop-start system, ensure that the charging potential does not exceed 14.6 volts when using a battery charger. Otherwise the vehicle battery might be damaged. Jump starting 3 218.
186 Vehicle care Lift the wiper arm until it stays in the raised position. Press the catches on both sides, tilt wiper blade at a 90° to the wiper arm and remove upwards. Insert in reverse order. Lower wiper arm carefully. Wiper blade on the rear window Lift wiper arm.
Vehicle care 187 Low beam 1. Rotate the cap (2) anticlockwise and remove it. 2. Press the clip to disengage bulb holder. Withdraw the bulb holder from the reflector. 3. Detach the bulb from the bulb holder and replace the bulb. 4. Insert the bulb holder with the clip downwards and engage into the reflector until it clicks.
188 Vehicle care 2. Press the clip to disengage bulb holder. Withdraw the bulb holder from the reflector. 3. Detach the bulb from the bulb holder and replace the bulb. 4. Insert the bulb holder with the clip downwards and engage into the reflector until it clicks.
Vehicle care 189 Sidelight/daytime running light with LEDs Sidelights and daytime running lights consist of LEDs which cannot be changed. Consult a workshop in case of a defective LED. Xenon headlights 9 Danger Xenon headlights work under extremely high electrical voltage.
190 Vehicle care Fog lights The bulbs are accessible from the underside of the vehicle. 1. Turn the bulb holder anti- clockwise and remove it from the reflector. 2. Disengage the bulb socket from the plug connector by pressing the retaining lug. 3. Remove and replace the bulb socket with bulb and attach the plug connector.
Vehicle care 191 2. Unscrew both plastic securing nuts from the inside by hand. 3. Carefully withdraw the light assembly from the recesses and remove. 4.
192 Vehicle care Reversing light is located on the right light assembly in the tailgate, and the rear fog light is located on the left light assembly in the tailgate. Right hand drive models Reversing light is located on the left light assembly in the tailgate, and the rear fog light is located on the right light assembly in the tailgate.
Vehicle care 193 Side turn signal lights To replace bulb, remove lamp housing: 1. Slide lamp to its left side and remove with its right end. 2. Turn bulb holder anticlockwise and remove from housing. 3. Pull bulb from bulb holder and replace it. 4. Insert bulb holder and turn clockwise.
194 Vehicle care 2. Remove lamp downwards, taking care not to pull on the cable. 3. Remove bulb holder from lamp housing by turning anticlockwise. 4. Pull bulb from bulb holder and replace it. 5. Insert bulb holder into lamp housing and turn clockwise.
Vehicle care 195 There are different kinds of fuses in the vehicle. Depending on the type of fuse, a blown fuse can be recognized by its melted wire. Do not replace the fuse until the cause of the fault has been remedied. Some functions are protected by several fuses.
196 Vehicle care No. Circuit 1 Trailer interface module 2 Exterior mirror switch 3 Battery sensor 4 Chassis control module 5 ABS 6 Daytime running light left 7 – 8 Transmission control module 9 Body.
Vehicle care 197 No. Circuit 32 Right headlamp 33 Engine control module 34 Horn 35 Clutch 36 Front fog lights No. Circuit 1 ABS pump 2 Front wiper 3 Blower 4 Instrument panel 5 – 6 Diesel fuel heate.
198 Vehicle care The fuse box is behind the light switch in the instrument panel. Hold the handle, then pull and fold down the light switch. Right-hand drive vehicles The fuse box is located behind a cover in the glovebox. Open the glovebox, then open the cover and fold it down.
Vehicle care 199 No. Circuit 1 – 2 – 3 Power windows 4 Voltage transformer 5 Body control module 1 6 Body control module 2 7 Body control module 3 8 Body control module 4 9 Body control module 5 10 Body control module 6 11 Body control module 7 12 Body control module 8 13 – 14 Tailgate 15 Airbag system 16 Data link connection 17 Ignition No.
200 Vehicle care Vehicle tools Tools Vehicles with tyre repair kit On versions with rear carrier system or double load-bay floor, the tools are located together with the towing eye and tyre repair kit on the right side in the load compartment behind a cover.
Vehicle care 201 Wheels and tyres Tyre condition, wheel condition Drive over edges slowly and at right angles if possible. Driving over sharp edges can cause tyre and wheel damage. Do not trap tyres on the kerb when parking. Regularly check the wheels for damage.
202 Vehicle care Tyre pressure 3 240. The tyre pressure information label on the right door frame indicates the original equipment tyres and the correspondent tyre pressures. The tyre pressure data refers to cold tyres. It applies to summer and winter tyres.
Vehicle care 203 The menu can be selected by the buttons on the turn signal lever. Press the MENU button to select the Vehicle Menu . Turn the adjuster wheel to select the tyre pressure monitoring system. Baselevel display and Midlevel display: The tyre pressure for each tyre is displayed on its own page.
204 Vehicle care If w illuminates at lower temperatures and extinguishes after driving, this could be an indicator for getting low pressure. Check tyre pressure. Vehicle messages 3 102. If the tyre pressure must be reduced or increased, switch off ignition.
Vehicle care 205 Select ■ Light for comfort pressure up to three people ■ Eco for Eco pressure up to three people ■ Max for full loading TPMS Sensor Matching Process Each TPMS sensor has a unique identification code.
206 Vehicle care Uplevel display: 6. Press the SET/CLR button to begin the sensor matching process. A message requesting acceptance of the process should display. 7. Press the SET/CLR button again to confirm the selection. The horn sounds twice to signal the receiver is in relearn mode.
Vehicle care 207 Tyres should be replaced for safety reasons at a tread depth of 2-3 mm (4 mm for winter tyres). For safety reasons it is recommended that the tread depth of the tyres on one axle should not vary by more than 2 mm. The legally permissible minimum tread depth (1.
208 Vehicle care 9 Warning Use of unsuitable tyres or wheel covers could lead to sudden pressure loss and thereby accidents. Steel wheels: When using locking wheel nuts don't attach wheel covers. Tyre chains Tyre chains are only permitted on the front wheels.
Vehicle care 209 Vehicles with tyre repair kit in the sidewall To open the compartment, disengage the cover and open it. 1. Take the sealant bottle and bracket with air hose from the insert. 2. Detach air hose from bracket and screw onto sealant bottle connection.
210 Vehicle care 4. Unscrew valve cap from defective tyre. 5. Screw tyre inflation hose to valve. 6. Screw air hose onto compressor connection. 7. Switch on ignition. To avoid discharging the battery, we recommend running the engine. 8. Press on/off switch on the compressor.
Vehicle care 211 14. Take the label indicating maximum permitted speed from the sealant bottle and affix in the driver's field of view. 15. Continue driving immediately so that sealant is evenly distributed in the tyre. After driving approx. 10 km (but no more than 10 minutes), stop and check tyre pressure.
212 Vehicle care 4. Screw the compressor air hose to the connection on the sealant bottle. 5. Fit the sealant bottle into the retainer on the compressor. Set the compressor near the tyre in such a way that the sealant bottle is upright. 6. Unscrew valve cap from defective tyre.
Vehicle care 213 Drain excess tyre pressure with the button over the pressure indicator. Do not run the compressor longer than 10 minutes. 14. Detach the tyre repair kit. Push catch on bracket to remove sealant bottle from bracket. Screw the tyre inflation hose to the free connection of the sealant bottle.
214 Vehicle care Make the following preparations and observe the following information: ■ Park the vehicle on a level, firm and non-skid surface. The front wheels must be in the straight-ahead position. ■ Apply the parking brake and engage first gear, reverse gear or P .
Vehicle care 215 2. Install the wheel wrench ensuring that it locates securely and loosen each wheel bolt by half a turn. The wheels might be protected by locking wheel bolts. To loosen these specific bolts first attach the key adapter onto the head of the bolt before installing the wheel wrench.
216 Vehicle care 9. Install the wheel wrench ensuring that it locates securely and tighten each bolt in a crosswise sequence. Tightening torque is 110 Nm. 10. Align the valve hole in the wheel cover of the steel wheel with the tyre valve before installing.
Vehicle care 217 The spare wheel has always a steel rim. Caution The use of a spare wheel that is smaller than the other wheels or in combination with winter tyres could affect driveability. Have the defective tyre replaced as soon as possible. The spare wheel is located in the load compartment beneath the floor covering.
218 Vehicle care Jump starting Do not start with a quick charger. A vehicle with a discharged vehicle battery can be started using jump leads and the vehicle battery of another vehicle.
Vehicle care 219 Lead connection order: 1. Connect the red lead to the positive terminal of the booster vehicle battery. 2. Connect the other end of the red lead to the positive terminal of the discharged vehicle battery. 3. Connect the black lead to the negative terminal of the booster vehicle battery.
220 Vehicle care Screw in the towing eye as far as it will go until it stops in a horizontal position. Attach a tow rope – or better still a tow rod – to the towing eye. The towing eye must only be used for towing and not for recovering the vehicle.
Vehicle care 221 Screw in the towing eye as far as it will go until it stops in a horizontal position. The lashing eye at the rear underneath the vehicle must never be used as a towing eye. Attach a tow rope – or even better a tow bar – to the towing eye.
222 Vehicle care Bird droppings, dead insects, resin, pollen and the like should be cleaned off immediately, as they contain aggressive constituents which can cause paint damage. If using a car wash, comply with the car wash manufacturer's instructions.
Vehicle care 223 For mechanical removal of ice, use a sharp-edged ice scraper. Press the scraper firmly against the glass so that no dirt can get under it and scratch the glass. Clean smearing wiper blades with a soft cloth and window cleaner. Remove dirt residues from smearing wiper blades by using a soft cloth and window cleaner.
224 Vehicle care The instrument cluster and the displays should only be cleaned using a soft damp cloth. If necessary use a weak soap solution. Clean fabric upholstery with a vacuum cleaner and brush. Remove stains with an upholstery cleaner. Clothing fabrics may not be colourfast.
Service and maintenance 225 Service and maintenance General information ................... 225 Recommended fluids, lubricants and parts ..............
226 Service and maintenance Confirmations Confirmation of service is recorded in the Service and Warranty Booklet. The date and mileage is completed with the stamp and signature of the servicing workshop.
Service and maintenance 227 Select the appropriate engine oil based on its quality and on the minimum ambient temperature 3 230. Additional engine oil additives The use of additional engine oil additives could cause damage and invalidate the warranty.
228 Technical data Technical data Vehicle identification .................. 228 Vehicle data ............................... 230 Vehicle identification Vehicle Identification Number The Vehicle Identification Number is stamped on the identification plate and on the floor pan, under the floor covering, visible under a cover.
Technical data 229 Identification plate The identification plate is located on the left door frame. Information on identification label: 1 = manufacturer 2 = type approval number 3 = vehicle Identific.
230 Technical data Vehicle data Recommended fluids and lubricants European service schedule Required engine oil quality All European countries (except Belarus, Moldova, Russia, Turkey) Only Israel Eng.
Technical data 231 International service schedule Required engine oil quality All countries outside Europe except Israel Only Belarus, Moldova, Russia, Turkey Engine oil quality Petrol engines (includ.
232 Technical data All countries outside Europe except Israel Only Belarus, Moldova, Russia, Turkey Engine oil quality Petrol engines (including CNG, LPG, E85) Diesel engines Petrol engines (including.
Technical data 233 Engine data Sales designation 1.0 1.0 1.2 1.4 1.4 1.4 Engine identifier code B10XFL B10XFT B12XEL B14XEJ B14XEL B14NEJ Number of cylinders 3 3 4 4 4 4 Piston displacement [cm 3 ] 99.
234 Technical data Sales designation 1.3 1.3 1.3 Engine identifier code B13DTC B13DTE B13DTE Number of cylinders 4 4 4 Piston displacement [cm 3 ] 1248 1248 1248 Engine power [kW] 55 55 70 at rpm 3750.
Technical data 235 Performance Engine B10XFL B10XFT B12XEL B14XEJ B14XEL B14NEJ Maximum speed 4) [km/h] Manual transmission 180 195 162 167 175 185 Manual transmission automated – – – – 175 – Automatic transmission – – – – 170 – 4) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload.
236 Technical data Vehicle weight Kerb weight, 5-door vehicle, basic model without any optional equipment Engine Manual transmission Manual transmission automated Automatic transmission without / with.
Technical data 237 Kerb weight, 3-door vehicle, basic model without any optional equipment Engine Manual transmission Manual transmission automated Automatic transmission without / with air conditioni.
238 Technical data 5-door vehicle 3-door vehicle Height (without antenna) [mm] 1481 1479 Length of load compartment floor [mm] 705 705 Length of load compartment with folded rear seats [mm] 1372 1372 .
Technical data 239 Capacities Engine oil Engine B10XFL B10XFT B12XEL B14XEJ B14NEJ B14XEL B13DTC B13DTE including Filter [l] 4.0 4.0 4.0 3.5 between MIN and MAX [l] 1.
240 Technical data Tyre pressures Comfort with up to 3 people ECO with up to 3 people With full load Engine Tyres front rear front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) B12XEL, B14XEL 175/70 R14, 185/70 R14, 185/65 R15, 195/55 R16, 215/45 R17, 210/2.
Technical data 241 Comfort with up to 3 people ECO with up to 3 people With full load Engine Tyres front rear front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) B10XFL, B10XFT, B14NEJ, B13DTC, B13DTE 185/65 R15, 195/55 R16, 215/45 R17, 230/2.
242 Customer information Customer information Customer information ................ 242 Vehicle data recording and pri‐ vacy ........................................... 243 Customer information Declaration of conformity Transmission systems This vehicle has systems that transmit and/or receive radio waves subject to Directive 1999/5/EC.
Customer information 243 Vehicle data recording and privacy Event data recorders Data storage modules in the vehicle A large number of electronic components of your vehicle contain data storage modules temporarily or permanently storing technical data about the condition of the vehicle, events and errors.
244 Customer information Radio Frequency Identification (RFID) RFID technology is used in some vehicles for functions such as tyre pressure monitoring and ignition system security.
Customer information 245.
246 Index A Accessories and vehicle modifications .......................... 178 Adjustable air vents ................... 128 Airbag and belt tensioners ........... 90 Airbag deactivation ................ 48, 90 Airbag label...........................
247 Control indicators.......................... 87 Control of the vehicle ................. 130 Controls ........................................ 76 Convex shape .............................. 30 Coolant and antifreeze ............... 226 Corner lighting .
248 Headlights................................... 110 Headlights when driving abroad 112 Head restraint adjustment ............. 8 Head restraints ............................ 36 Heated mirrors ............................. 30 Heated rear window .....
249 R Radio Frequency Identification (RFID) ..................................... 244 Radio remote control ................... 23 Reading lights ............................ 118 Rear carrier system ...................... 60 Rear floor storage cover ..
250 V Vehicle battery ........................... 183 Vehicle checks............................ 179 Vehicle data ................................ 230 Vehicle data recording and privacy ..................................... 243 Vehicle detected ahead .
Ein wichtiger Punkt beim Kauf des Geräts Opel Corsa (2015) (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Opel Corsa (2015) noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Opel Corsa (2015) - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Opel Corsa (2015) reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Opel Corsa (2015) erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Opel Corsa (2015) besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Opel Corsa (2015) verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Opel Corsa (2015). Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Opel Corsa (2015) gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
