Benutzeranleitung / Produktwartung Microline 390FB des Produzenten OKI
Zur Seite of 29
MICROLINE 320/390FB User Manual (English) MICROLINE 320/390FB User Manual (English).
E – 1 English Table of Contents Note to Customers ................................... E-2 Important Safety Instructions .................. E-3 Important Wiring Instructions ................. E-4 Installing Your Printer ............................. E-5 Preliminaries .
E – 2 Note to Customers Every effort has been made to ensure that the information in this manual is complete, accurate and up-to-date. Oki assumes no responsibility for errors beyond its control.
E – 3 Important Safety Instructions Your printer has been carefully designed to perform safely and reliably. However, as with all electrical equipment certain precautions should be allowed: ➢ Read all documentation supplied with and on the printer before commencing.
E – 4 Important Wiring Instructions The wires in the mains lead are coloured in accordance with the following code: Green and Yellow Earth Blue Neutral Brown Live If the colours of the wires in the .
E – 5 Installing Your Printer Prior to unpacking the printer, find a flat, sturdy surface to place it on, for example, a desk, printer stand, etc. Gently remove the printer from its carton.
E – 6 Preliminaries Before plugging in the printer, follow these steps to install your printer. 1. Hold both sides of the access cover and lift up. There is a shipping retainer to protect the printhead from jamming. Remove this shipping retainer and keep it with the other packing materials.
E – 7 2 . Next install the sheet stacker. Put the stud of one of the stacker’s legs into the hole at the end of the rear vent. Gently press the other leg until it slips into the other hole. 3 . Make sure the power switch is OFF. Plug the power cord into the back of the printer.
E – 8 5. Turn the power switch off. Important: Make sure the socket is earthed. Do not use an adapter because it will defeat the earthing. !.
E – 9 Connecting to the Computer These instructions are for the standard centronics parallel interface. 1 . Make sure that both the printer and the computer are switched OFF. 2 . Plug the interface cable into the port on the back of your printer. Fasten the the cable using the wire clips that can be found on both sides of the connector port.
E – 10 Installing the Ribbon Cartridge 1 . Set the headgap lever to the “R” position. 2 . Open the access cover. 3 . Slide the print head gently towards the centre to give yourself some working room. There is a cut-out at the centre of the sheet guide for changing cartridges.
E – 11 5 . Insert the flat end of the cartridge into the upper part of the ribbon plate, then lower the front of the cartridge over the printhead until it snaps into place. 6 . Turn the take-up knob in the direction of the arrow icon to tighten the ribbon.
E – 12 Important: Do not peel off the plastic film (ribbon mask) on the top of the cartridge. Do not stack the ribbon cartridge sideways, it will cause poor quality printing. Loading Paper Loading Continuous Paper 1 . Check that the POWER lamp is turned on.
E – 13 3 . Push the paper lever to the continuous paper position. 4 . Adjust the headgap lever on the left side of the printer according to your paper thickness. At its lowest (position 1), the lever sets a thickness for one sheet of paper. It clicks through seven positions showing the number of sheets.
E – 14 Note: In the positions above 5, the printer slows down to maintain print quality with thicker multipart forms. Note: “R” position indicates ribbon cartridge replacement position. 5 . Hold both sides of the paper table and lift up gently. 6 .
E – 15 7 . Open both of the pin-tractors covers. 8 . Lay down the continuous paper with printing face upwards on to the pin-tractors. Adjust the paper so that the first two pins of both pin tractors poke through the two sprocket holes of the paper. Make sure that the paper covers the pin tractors.
E – 16 Note: The arrow icon ( ▼ ▼ ▼ ▼ ▼ ) on the scale and also the centre of the diamond shaped hole indicate the centre of the first printed character. 10. Slide the right pin-tractor to tighten the paper. Press the right lock lever down.
E – 17 11. Close the table. The extension guide is not necessary when using continuous paper. Push it clockwise so that it folds under the sheet stacker. 12. When you close the table, the ALARM lamp comes on, do not worry, it is just telling you that there is no paper loaded.
E – 18 Loading Cut Sheet paper 1 . Check that the power is on. 2 . Check that the SEL lamp is off (printer off-line). If it is on push the SEL button to turn it off. 3 . Pull the paper lever to the forwards position, (cut sheet paper position). 4 . Position the headgap lever to the appropriate setting for your paper thickness.
E – 19 Note: Unless you alter the standard margin setting using the MENU MODE, the paper guide must be placed correctly against the arrow icon: too big a left margin may cause printing on the platen and not the paper, resulting in a loss of data. 6.
E – 20 Setting the Top of Form Your printer can adjust the top of form (the first line of the printing surface) by increments of 1 / 144 inch. This allows you to set a desired top of form very precisely. 1. To advance the paper, keep pressing the TOF/ QUIET button and press the FORM FEED button.
E – 21 3 . Release the two buttons at the desired top of form position. Press the TOF/QUIET button again to fix the setting. It remains in the printer’s memory and will not change until the printer is reset. Note 1: The reverse process is limited in order to avoid paper jams.
E – 22 2 . Also, keep the printer 60 cm or more from the wall in order to store paper. These storage requirements are necessary to avoid jammmg. Running a Self Test Now that you have installed the ribbon and paper, you are ready to run one of two types of self test.
E – 23 Printing Demo Patterns 1 . First load the printer with the correct paper. 2 . Switch off the power to the printer. 3 . Choose the demo pattern you want to produce and associated button, from the following table. 4 . Keep pressing the button and turn on the power.
E – 24 Changing Menu Settings To change the menu settings follow these steps: 1. Make sure that the printer is on line. 2 . Press the MODE/Exit button to put the printer in Menu Mode. 3 . Press the TOF/QUIET/Print button to print a list of menu settings.
E – 25 If you want to return the printer to the factory default settings, turn the power on while holding down the MODE/Exit and SEL buttons, all menu settings will then return to the factory default.
E – 26 Specifications Print method Impact dot matrix Printhead 24 pin (ML390FB) 9 pin (ML320FB) Print speed Utility 270 cps at 12 cpi (ML390FB) 250 cps at 12 cpi (ML320FB) Letter quality 90 cps at 12 cpi (ML390FB) 62.5 cps at 12 cpi (ML320FB) Characters per line at 10 cpi 106 at 12 cpi 127 at 15 cpi 159 at 17.
E – 27 Electrical characteristics Voltage 230V AC(+6%-14%). 240V AC(±10%). Frequency 50/60Hz ±2%. Data interface Centronics parallel standard. RS232C serial optional. Dimensions Depth 343mm. Width 465mm. Height 200mm. Weight 12kg. Continuous paper Wid th 76.
E – 28 Cut sheets Wid th 90mm to 304.8mm. Length 70mm to 420mm. Single part Weight 12 t o 41lb. Thickness 0.051mm to 0.196mm. Multipart* Weight Paper: 10 to 12lb. Carbon: 9lb. Number of copies Original plus 4 copies. Thickness 0.36mm max. * Note: All parts must be glued at the top.
Ein wichtiger Punkt beim Kauf des Geräts OKI Microline 390FB (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie OKI Microline 390FB noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für OKI Microline 390FB - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von OKI Microline 390FB reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über OKI Microline 390FB erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon OKI Microline 390FB besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von OKI Microline 390FB verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit OKI Microline 390FB. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei OKI Microline 390FB gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
