Benutzeranleitung / Produktwartung MC562 des Produzenten OKI
Zur Seite of 120
Start-up Guide This guide supports the following models: MC352, MC362, MC562, ES3452 MFP, ES5462 MFP.
- 2 - PREFACE Every effort has been made to ensure that the information in this document is complete, accur ate, and up-to-date. The manufacturer assumes no responsibility for the result of errors bey ond its control.
- 3 - EMERGENCY FIRST AID Exercise care in the handling and use of toner powder: If swallowed, give small amounts of cold water and seek medical attention. DO NOT attempt to induce vomiting. If inhaled, move the person to an open area for fresh air. Seek medical attention.
- 4 - ● ● For Your Safety Read the Start -up Guide (this guide) and User’s Guide for y our safety before using the product. Cautions related to safety W ARNING Indicates the presence of a hazard for which not following the instructions noted may result in serious injury or death.
- 5 - Table of Contents PREF ACE ................................................................................................ 2 EMERGENCY FIRST AID ........................................................................... 3 MANUF ACTURER .......
- 6 - T able of Contents 3 Faxing (For MC362, MC562, ES5462 MFP only) .................. 24 Initial Setup for F axing .......................................................................... 25 Step 1 Setting Country Code ...........................
- 7 - T able of Contents 4 Scanning ............................................................................ 49 Scanning to E-mail ................................................................................ 49 Initial Setup for Scan to E-mail .
- 8 - ● ● About This Guide Terms in this document The following terms are used in this guide: Note ● Indicates important information on operations. Please ensure y ou read these. Memo ● Indicates additional information on operations. It is recommended that this be read.
- 9 - Notation used in this guide The following notations may be used in this manual. ● PostScript3 Emulation → PSE, POSTSCRIPT3 Emulation, POSTSCRIPT3 EMULA TION ● Microsoft ® Windows ® 7 64-.
- 10 - 1 Machine Setup 1 Machine Setup This chapter explains the initial setup for the machine, including the names of the machine components, how to unpack and install the machine, how to turn on/off the machine, and how to load paper into tra y 1.
- 11 - Names of Components 1 Machine Setup LINE TEL 25 23 21 22 24 No. Name 21 F aceup stacker 22 AC power socket 23 Air vents 24 LINE connection (for MC362/MC562/ES5462 MFP only) 25 TEL connection (for MC362/MC562/ES5462 MFP only) 27 28 26 No.
- 12 - Names of Components 1 Machine Setup Operator Panel The following shows the names of the components of the oper ator panel. Reference ● For the details on the functions of each component, refer to the User’ s Guide > “Introduction” > “Control panel” .
- 13 - Installing Y our Machine 1 Machine Setup ● ● Installing Your Machine This section explains how to unpack and install the machine. Installation Requirements This section explains the required environment and space for machine installation.
- 14 - Installing Y our Machine 1 Machine Setup Unpacking and Installing Your Machine This section explains how to unpack and install the machine. Note ● The image drum is very delicate. Handle it carefully . ● Do not expose the image drum to direct sunlight or very bright interior light (approximately more than 1500lux).
- 15 - Installing Y our Machine 1 Machine Setup 8 R emove the protection tapes (6). Open the ADF and remove the protection tapes. 6 9 Close the document glass cover . Now , you can open or close the scanner . 10 Open the scanner unit. 11 R emove the protection tapes (7), and remove desiccants and lms.
- 16 - Installing Y our Machine 1 Machine Setup 15 While pushing the right side of the toner cartridge, quickly slide the blue lock (12) to the left side to lock it. Slide the locks on all 4 toner cartridges. 16 Close the top co ver . 17 Close the scanner unit.
- 17 - Installing Y our Machine 1 Machine Setup Turning Your Machine On and Off This section explains how to turn the machine on and off . Power Supply Conditions The power supply must meet the follow.
- 18 - Installing Y our Machine 1 Machine Setup Turning On Your Machine 1 Plug the AC cord into the AC power socket of your machine. 2 Plug the AC cord into the electric socket. 3 Check that no documents are on the document glass or ADF , and that the ADF cover is closed.
- 19 - Installing Y our Machine 1 Machine Setup Loading Paper Y our machine has two built-in tra ys (tray 1 and MP tr ay) and an optional tray (tr ay 2). This section explains the supported paper and capacity of tr ay 1 and how to load paper into the tra y 1.
- 20 - Installing Y our Machine 1 Machine Setup 4 Flex paper back and forth, and then fan it. Straighten the edges of the paper stack on a level surface. 5 Load paper with the print side face down. Note ● Do not load paper above the ll line (3). [ ▼ ▼ ▼ ] 3 6 Push tra y 1 until it stops.
- 21 - Printing Conguration 1 Machine Setup ● ● Printing Conguration This section explains how to print the Conguration on which y ou can check the detailed information of your machine, such as the settings and status of y our machine.
- 22 - 2 Copying 2 Copying This chapter explains the basic operation for y our machine’ s copy function. Starting a Copy Job Memo ● The following procedure uses the factory default settings. 1 Press the < COPY > key on the oper ator panel to open the copy standby screen.
- 23 - 2 Copying 3 Press M ONO or C OLOR to start copying. Memo ● Y ou can cancel the operation b y pressing the < STOP > key on the operator panel until the message showing the copy completion is displayed. Reference ● T o load a landscape document, refer to the User’s Guide > “Operation” > “Loading document(s)” .
- 24 - 3 F axing (F or MB362, MB562, ES5462 MFP only) 3 Faxing (For MC362, MC562, ES5462 MFP only) This chapter explains the initial setup, such as how to set the country code, connect a telephone line and congure the basic settings, and basic procedure for the F ax and F ax from Computer functions.
- 25 - Initial Setup for F axing 3 F axing (F or MB362, MB562, ES5462 MFP only) ● ● Initial Setup for Faxing This section explains the initial setup necessary for the F ax and F ax from Computer functions. T o set up the machine for the F ax and F ax from Computer functions, follow the 3 steps below: ● “Step 1 Setting Country Code” P .
- 26 - Initial Setup for F axing 3 F axing (F or MB362, MB562, ES5462 MFP only) 5 Press the to select [ Fax Setup ] and then press OK . 6 Press the to select [ Fax Setting ] and then press OK . 7 Press the to select [ Country Code ] and then press OK .
- 27 - Initial Setup for F axing 3 F axing (F or MB362, MB562, ES5462 MFP only) 2 Plug one end of the [ Telephone cable ] into the [ LINE connection ] of your machine and the other end into the [ Public Line (Analog) ]. LINE connection T elephone cable Public Line (Analog) Note ● Be certain to connect the telephone cable to [ LINE connection ].
- 28 - Initial Setup for F axing 3 F axing (F or MB362, MB562, ES5462 MFP only) Connecting to an ADSL Environment Note ● Do not connect with USB cable or LAN cable at this point. First, check that the machine is turned off . If the machine is turned on, hold down the power switch for approximately one second to turn off the power .
- 29 - Initial Setup for F axing 3 F axing (F or MB362, MB562, ES5462 MFP only) Connecting to a CS Tuner or Digital Television Note ● Do not connect with USB cable or LAN cable at this point. First, check that the machine is turned off . If the machine is turned on, hold down the power switch for approximately one second to turn off the power .
- 30 - Initial Setup for F axing 3 F axing (F or MB362, MB562, ES5462 MFP only) Connecting as an Internal Telephone Note ● Do not connect with USB cable or LAN cable at this point. First, check that the machine is turned off . If the machine is turned on, hold down the power switch for approximately one second to turn off the power .
- 31 - Initial Setup for F axing 3 F axing (F or MB362, MB562, ES5462 MFP only) 2 Press the to select [ Admin Setup ], and press OK . 3 Enter the administrator password. The factory default password is “aaaaaa” . a Press , , , to select the character y ou want, and then press OK .
- 32 - Initial Setup for F axing 3 F axing (F or MB362, MB562, ES5462 MFP only) a Press , , , to select the character y ou want, and then press OK . - The selected char acter is entered as “*” in the text eld. - If you ha ve entered an incorrect value, press the < CLEAR > key and then enter the correct value.
- 33 - Initial Setup for F axing 3 F axing (F or MB362, MB562, ES5462 MFP only) Step 3-3 Specifying Sender Information Specify the fax number and sender name for your machine. The information specied here is printed on the top of the faxes y ou sent from the machine.
- 34 - Initial Setup for F axing 3 F axing (F or MB362, MB562, ES5462 MFP only) 6 Enter the fax number of your machine with the ten-key pad. 7 Check that [ Enter ] is selected and then press OK . 8 Press to select the [ Sender ID ] entry box. 9 Enter an arbitrary sender name up to 22 characters allowed.
- 35 - Initial Setup for F axing 3 F axing (F or MB362, MB562, ES5462 MFP only) - The selected char acter is entered as “*” in the text eld. - If you ha ve entered an incorrect value, press the < CLEAR > key and then enter the correct value.
- 36 - Initial Setup for F axing 3 F axing (F or MB362, MB562, ES5462 MFP only) - The selected char acter is entered as “*” in the text eld. - If you ha ve entered an incorrect value, press the < CLEAR > key and then enter the correct value.
- 37 - Initial Setup for F axing 3 F axing (F or MB362, MB562, ES5462 MFP only) a Press , , , to select the character y ou want, and then press OK . - The selected char acter is entered as “*” in the text eld. - If you ha ve entered an incorrect value, press the < CLEAR > key and then enter the correct value.
- 38 - F axing 3 F axing (F or MB362, MB562, ES5462 MFP only) ● ● Faxing This section explains the basic procedure for the F ax function. The F ax function enables you to scan documents and tr ansmit them as faxes or receive fax es via a telephone line.
- 39 - F axing 3 F axing (F or MB362, MB562, ES5462 MFP only) 4 Check that [ Add Destination ] is selected on the start screen and then press OK . 5 Press the to select [ Direct Input ] and then press OK . 6 Enter a destination fax number up to 40 digits using the ten-key pad on the operator panel.
- 40 - F axing 3 F axing (F or MB362, MB562, ES5462 MFP only) Receiving a Fax This section explains how your machine behav es when the machine whose reception mode is set to [ Fax Ready Mode ] is receiving and printing faxes.
- 41 - F axing from a Computer (For Windows) 3 F axing (F or MB362, MB562, ES5462 MFP only) ● ● Faxing from a Computer (For Windows) This section explains how to install a fax driver and the basic procedure of sending a fax from a computer .
- 42 - F axing from a Computer (For Windows) 3 F axing (F or MB362, MB562, ES5462 MFP only) 1 Prepare an Ethernet cable and a hub. Prepare an Ethernet cable (category 5, twisted pair , straight) and a hub separately . 2 Hold down the power switch for approximately one second to turn off the power .
- 43 - F axing from a Computer (For Windows) 3 F axing (F or MB362, MB562, ES5462 MFP only) a Press , , , to select the character y ou want, and then press OK . - The selected char acter is entered as “*” in the text eld. - If you ha ve entered an incorrect value, press the < CLEAR > key and then enter the correct value.
- 44 - F axing from a Computer (For Windows) 3 F axing (F or MB362, MB562, ES5462 MFP only) 1 Press the < SETTING > key on the operator panel. 2 Check that [ Reports ] is selected and press OK . 3 Press the to select [ System ] and press OK . 4 Press the to select [ Network Information ] and press OK .
- 45 - F axing from a Computer (For Windows) 3 F axing (F or MB362, MB562, ES5462 MFP only) 8 On the [ Pre-Installation Check ] dialog box, click [ Next ]. 9 Click the [ Easy Installation (Network) ] button. The device search starts. - If the machine is detected, it is automatically installed.
- 46 - F axing from a Computer (For Windows) 3 F axing (F or MB362, MB562, ES5462 MFP only) For USB Connection Follow the procedure below to connect a USB cable and install a fax driver on your computer . Note ● Y ou must be logged in as an administr ator to complete this procedure.
- 47 - F axing from a Computer (For Windows) 3 F axing (F or MB362, MB562, ES5462 MFP only) 11 Click the Install button on the [ FAX driver ] row . 12 On the [ Pre-Installation Check ] dialog box, click [ Next ]. 13 Click [ Easy Installation (Local) ] button.
- 48 - F axing from a Computer (For Windows) 3 F axing (F or MB362, MB562, ES5462 MFP only) 19 Check that the OKI MC562(F AX) icon is displayed. If a printer driver for the machine is already installed, the OKI MC562 icon may represent these drivers.
- 49 - 4 Scanning 4 Scanning This chapter explains the initial setup and basic procedure for the Scan to E-mail, Scan to Network PC, and Scan to Local PC functions.
- 50 - Scanning to E-mail 4 Scanning Memo ● If conguring a small network consisting of only your machine and a computer , set IP addresses as shown below (according to RFC1918). For the computer IP address : 192.168.0.1~254 Subnet mask : 255.255.
- 51 - Scanning to E-mail 4 Scanning 6 Press the < SETTING > key on the operator panel. 7 Press the to select [ Easy Setup ], and press OK . 8 Enter the administrator password. The factory default password is “aaaaaa” . a Press , , , to select the character y ou want, and then press OK .
- 52 - Scanning to E-mail 4 Scanning 14 Enter the DNS serv er and WINS server if needed. If it is not necessary to connect the DNS server or WINS server to the network, press OK until the pop-up message showing setting completion is displayed. 15 When the setup menu screen is displayed, press to complete the setup.
- 53 - Scanning to E-mail 4 Scanning Step 2 Conguring the E-mail Settings of Your Machine T o congure the E-mail Settings of your machine, follow the 3 sub steps below: ● “Step 2-1 Checking the E-mail Settings of the Computer” P .53 ● “Step 2-2 Setting the E-mail Address for Y our Machine” P .
- 54 - Scanning to E-mail 4 Scanning 4 On the [ General ] tab, enter the contents of [ Name ] and [ E-mail address ] in B-9 and B-10 of the Setup Information F orm. B-9 B-10 5 Click the [ Servers ] tab, and then note each setting in the corresponding columns of the Setup Information F orm.
- 55 - Scanning to E-mail 4 Scanning 1 Press the < SETTING > key on the operator panel. 2 Press the to select [ Easy Setup ] and press OK . 3 Enter the administrator password. The factory default password is “aaaaaa” . a Press , , , to select the character y ou want, and then press OK .
- 56 - Scanning to E-mail 4 Scanning 15 Press the and then enter the information in B-6. 16 Select [ Enter ] and then press OK . Proceed to step 21. 17 Press the and then enter the information in B-7. 18 Select [ Enter ] and then press OK . 19 Press the and then enter the information in B-8.
- 57 - Scanning to E-mail 4 Scanning ● Document Glass Place a document face down and align its top edge to the upper-left corner of the glass. Close the document glass cover gently . Note ● Do not apply an excessive load to the document glass. Memo ● The machine prioritizes the ADF when scanning documents.
- 58 - Scanning to Network PC 4 Scanning ● ● Scanning to Network PC This section explains the initial setup and basic procedure for the Scan to Network PC function. This function enables you to scan documents and sav e the scanned images to the “shared folder” of a computer on the network.
- 59 - Scanning to Network PC 4 Scanning 3 Plug one end of the Ethernet cable into the network interface connection on the back of the machine. 4 Plug the other end of the Ethernet cable into the hub. 5 Hold down the power switch for approximately one second to turn on the power .
- 60 - Scanning to Network PC 4 Scanning c Press the and to select [ Enter ] and press OK . 9 Press the to select [ Network Setting ], and then press the . 10 If setting the IP address manually , check that [ Manual ] is selected, and press OK . If obtaining the IP address automatically , press the to select [ Auto ], and press OK .
- 61 - Scanning to Network PC 4 Scanning Step 2 Setting Up Your Computer and Machine for Scan to Network PC T o setup your computer and machine for Scan to Network PC, follow the 4 sub steps below: ● “Step 2-1 Checking the Name of the Computer” P .
- 62 - Scanning to Network PC 4 Scanning For Windows Server 2003 and Windows XP 1 Click [ start ] > [ Control Panel ] > [ Performance and Maintenance ] > [ System ]. For Windows Serv er 2003, click [ Start ] > [ Operator panel ] > [ System ].
- 63 - Scanning to Network PC 4 Scanning Step 2-3 Conguring the Computer for Scan to Network PC With the Setup Information F orm, create an account and shared folder for the machine in the computer . Memo ● If the computer is in a domain, the procedure for adding a user account may differ from the procedure below .
- 64 - Scanning to Network PC 4 Scanning 13 Select the user account created in step 5 from the drop down box, and then click [ Add ]. 14 Check that the user added in step 13 is displayed and then click [ Share ].
- 65 - Scanning to Network PC 4 Scanning 4 Enter the value of C -2 in the text box and click [ Next ]. 5 Select [ Limited ] and click [ Create Account ].
- 66 - Scanning to Network PC 4 Scanning 14 Select the [ Share this folder on the network ] and [ Allow network users to change my les ] checkbox, and then click [ OK ]. Proceed to “Step 2-4 Creating a Prole for Scan to Network PC” P .70 . 15 Click [ Add ].
- 67 - Scanning to Network PC 4 Scanning 4 Select [ User can not change password ] and [ Password never expires ], and then click [ Create ]. Memo ● If [ User must change password at next logon ] is selected, deselect so that you can select [ User can not change password ] and [ Password never expires ].
- 68 - Scanning to Network PC 4 Scanning 5 Select [ Standard ] from [ New Account ]. 6 Enter the value of C -2 in [ Full Name ]. For Mac OS X 10.5, enter the v alue of C -2 in [ Name ]. 7 Enter the value in C -3 in both [ Password ] and [ Verify ]. 8 Click [ Create User ] (for Mac OS X 10.
- 69 - Scanning to Network PC 4 Scanning 18 Click the triangle button at the right side of the user added in step 17 and select [ Read & Write ]. 19 Click [ Options ]. 20 Select the checkbo x for [ Share les and folders using SMB (Windows) ]. For Mac OS X 10.
- 70 - Scanning to Network PC 4 Scanning 8 Check that an account is added to [ Other Accounts ] with the name of C -2, and close [ Accounts ]. 9 Create a new folder on the computer with the name entered in C -5. 10 From the Apple menu, select [ System Preferences ].
- 71 - Scanning to Network PC 4 Scanning a Press , , , to select the character y ou want, and then press OK . - The selected char acter is entered in the text eld. - If you ha ve entered an incorrect value, press the < CLEAR > key and then enter the correct value.
- 72 - Scanning to Network PC 4 Scanning Procedure for Scan to Network PC This section explains how to start Scan to Network PC. Y ou need to congure the initial settings before using the Scan to Network PC function. Memo ● The following procedure uses the factory default settings.
- 73 - Scanning to Local PC 4 Scanning ● ● Scanning to Local PC This section explains the initial setup and basic procedure for the Scan to Local PC function. This function enables you to scan documents to the computer via network or USB , and manipulate the scanned images as necessary .
- 74 - Scanning to Local PC 4 Scanning For Network Connection T o congure the Scan to Local PC function via the network connection, follow the 2 steps below: ● “Step 1 Conguring the Network Settings of Y our Machine” P .74 ● “Step 2 Installing Driver and Software” P .
- 75 - Scanning to Local PC 4 Scanning 3 Plug one end of the Ethernet cable into the network interface connection on the back of the machine. 4 Plug the other end of the Ethernet cable into the hub. 5 Hold down the power switch for approximately one second to turn on the power .
- 76 - Scanning to Local PC 4 Scanning c Press the and to select [ Enter ] and press OK . 9 Press the to select [ Network Setting ], and then press the . 10 If setting the IP address manually , check that [ Manual ] is selected, and press OK . If obtaining the IP address automatically , press the to select [ Auto ], and press OK .
- 77 - Scanning to Local PC 4 Scanning Step 2 Installing Driver and Software The following procedure installs a scanner driver and ActK ey at once. 1 Check that your machine and the computer are turned on and connected, and then insert the”Software DVD-ROM” into the computer .
- 78 - Scanning to Local PC 4 Scanning 10 Click [ Restart search ] to restart the device search. After the machine is displayed, select the machine and click [ Next ].
- 79 - Scanning to Local PC 4 Scanning 3 Plug one end of the USB cable into the USB interface connector on the back of the machine. 4 T urn on the computer . 5 Insert “Software DVD-ROM” into the computer . 6 Click [ Run Setup.exe ] after [ AutoPlay ] is displayed.
- 80 - Scanning to Local PC 4 Scanning 13 When the instruction to connect the machine to the computer and turn on the machine is displayed, plug the other end of the USB cable into the computer’ s USB interface connector and hold down the power switch for approximately one second to turn on the power .
- 81 - Scanning to Local PC 4 Scanning Memo ● If conguring a small network consisting of only your machine and a computer , set IP addresses as shown below (according to RFC1918). For the computer IP address : 192.168.0.1~254 Subnet mask : 255.255.
- 82 - Scanning to Local PC 4 Scanning 6 Press the < SETTING > key on the operator panel. 7 Press the to select [ Easy Setup ], and press OK . 8 Enter the administrator password. The factory default password is “aaaaaa” . a Press , , , to select the character y ou want, and then press OK .
- 83 - Scanning to Local PC 4 Scanning 14 Enter the DNS serv er and WINS server if needed. If it is not necessary to connect the DNS server or WINS server to the network, press OK until the pop-up message showing setting completion is displayed. 15 When the setup menu screen is displayed, press to complete the setup.
- 84 - Scanning to Local PC 4 Scanning 8 When the balloon message saying that the installation is complete is displayed on the task bar , click the balloon to check the details, and click [ Close ]. 9 Press the < SCAN > key on the oper ator panel.
- 85 - Scanning to Local PC 4 Scanning Step 1 Connecting Your Machine and Computer Select the connection method and follow each procedure. ● “For Network Connection” P .
- 86 - Scanning to Local PC 4 Scanning 3 Plug one end of the Ethernet cable into the network interface connection on the back of the machine. 4 Plug the other end of the Ethernet cable into the hub. 5 Hold down the power switch for approximately one second to turn on the power .
- 87 - Scanning to Local PC 4 Scanning c Press the and to select [ Enter ] and press OK . 9 Press the to select [ Network Setting ], and then press the . 10 If setting the IP address manually , check that [ Manual ] is selected, and press OK . If obtaining the IP address automatically , press the to select [ Auto ], and press OK .
- 88 - Scanning to Local PC 4 Scanning For USB Connection 1 Prepare a USB cable. A USB cable is not supplied with your machine. Prepare a USB 2.0 cable separately . Memo ● Use a USB 2.0 Hi-Speed cable for a USB 2.0 Hi- Speed connection. 2 Hold down the power switch for approximately one second to turn off the power .
- 89 - Scanning to Local PC 4 Scanning 6 Check the display and click [ Continue ] if OK. 7 R ead the license agreement and click [ Continue ]. 8 Click [ Agree ] if you agree. 9 Click [ Install ]. T o change the installation location of the driver , click [ Change Install Location ].
- 90 - Scanning to Local PC 4 Scanning Procedure for Scan to Local PC This section explains how to start Scan to Local PC. The following procedure is common for Windows and Mac OS X. Y ou need to congure the initial settings before using the Scan to Local PC function.
- 91 - Scanning to Local PC 4 Scanning 3 Press the to select [ Local PC ] and then press OK . 4 Check that [ Select A Connecting PC ] is selected and then press OK . 5 Check that [ From Network ] is selected and then press OK . 6 Press the to select the computer you want and then press OK .
- 92 - Scanning to Local PC 4 Scanning 2 Place your document in the ADF or on the document glass as below: ● ADF Load documents face up with the top edge of the documents in rst.
- 93 - Scanning to Local PC 4 Scanning For WSD Scan Connection (Windows only) 1 Press the < SCAN > key on the oper ator panel. 2 Place your document in the ADF or on the document glass as below: ● ADF Load documents face up with the top edge of the documents in rst.
- 94 - Scanning to Local PC 4 Scanning 7 Press M ONO or C OLOR . The scan job is processed according to the action set for the selected event. Reference ● T o load a landscape document, refer to the User’s Guide > “Operation” > “Loading document(s)” .
- 95 - 5 Printing 5 Printing This chapter explains the initial setup and basic procedure for the Print from Computer function. Y our machine supports the following print functions. Function Overview “Printing from a Computer” Prints a document sent from a computer connected via USB or network.
- 96 - Printing from a Computer 5 Printing For Network Connection T o install a printer driver on your computer via the network connection, follow the 2 steps below: ● “Step 1 Conguring the Network Settings of Y our Machine” P .96 ● “Step 2 Installing a Printer Driver” P .
- 97 - Printing from a Computer 5 Printing 4 Plug the other end of the Ethernet cable into the hub. 5 Hold down the power switch for approximately one second to turn on the power . 6 Press the < SETTING > key on the operator panel. 7 Press the to select [ Easy Setup ], and press OK .
- 98 - Printing from a Computer 5 Printing 11 Enter the IP address using the ten-key pad, and press OK . T o move to the next box, press the . 12 Enter the subnet mask using the ten-k ey pad, and press OK . T o move to the next box, press the . 13 Enter the default gatew ay address using the ten-key pad, and press OK .
- 99 - Printing from a Computer 5 Printing 4 Select the device of your machine, and then click [ Next ]. 5 R ead the license agreement and then click [ I Agree ]. 6 R ead the “Environmental advice for Users” and click [ Next ]. 7 Select the checkbox for the printer driver you w ant to install, and click the Install bunch button.
- 100 - Printing from a Computer 5 Printing 12 Click the [ Exit ] button. 13 R emove the “Softw are DVD-ROM” from the computer . The installation is complete. ◆ Print a test page to check that the printer driver is successfully installed on the computer .
- 101 - Printing from a Computer 5 Printing 5 Insert “Software DVD-ROM” into the computer . 6 Click [ Run Setup.exe ] after [ AutoPlay ] is displayed. If the [ User Account Control ] dialog box is displayed, click [ Yes ]. 7 Select the language and then click [ Next ].
- 102 - Printing from a Computer 5 Printing 13 When the instruction to connect the machine to the computer and turn on the machine is displayed, plug the other end of the USB cable into the computer’ s USB interface connector and hold down the power switch for about a second to turn on the power .
- 103 - Printing from a Computer 5 Printing For Mac OS X Overview Connecting Methods Y ou can select either of the following connection methods: ● “For Network Connection” P .103 ● “For USB Connection” P .110 Product Requirements Y our machine supports Mac OS X 10.
- 104 - Printing from a Computer 5 Printing 2 Hold down the power switch for approximately one second to turn off the power . And turn off a computer . 3 Plug one end of the Ethernet cable into the network interface connection on the back of the machine.
- 105 - Printing from a Computer 5 Printing a Press , , , to select the character y ou want, and then press OK . - The selected char acter is entered as “*” in the text eld. - If you ha ve entered an incorrect value, press the < CLEAR > key and then enter the correct value.
- 106 - Printing from a Computer 5 Printing ◆ Print the Network Information to check that the IP address and other network information are properly set. 1 Press the < SETTING > key on the operator panel. 2 Check that [ Reports ] is selected and press OK .
- 107 - Printing from a Computer 5 Printing 7 Press the to select [ OFF ], and press OK . 8 Press the until the top screen is displayed. Step 3 Installing a Printer Driver ◆ For Mac OS X 10.5 to 10.7 1 Check that your machine and the computer are turned on and connected.
- 108 - Printing from a Computer 5 Printing 12 Check that y our machine is displayed in [ Printers ] and [ OKI MC562(PS) ] is displayed in [ Kind ]. Note ● If [ OKI MC562(PS) ] is not correctly displayed in [ Kind ], click [ - ] to remove your machine from [ Printers ] and then redo the procedure from step 8 to 12.
- 109 - Printing from a Computer 5 Printing 11 Select the name of your machine whose [ Connection ] is [ Bonjour ], and then check that [ OKI MC562(PS) ] is displayed in [ Print Using ]. The name of your machine is display ed “OKI- MC562- (the last six digits of the MAC address)” .
- 110 - Printing from a Computer 5 Printing For USB Connection Follow the procedure below to connect a USB cable and install a printer driver on y our computer . For Mac OS X 10.5 to 10.7 Note ● Disable the anti-virus softw are before starting this procedure.
- 111 - Printing from a Computer 5 Printing 11 Click [ + ] and select [ Add Other Printer or Scanner ] on the pop-up menu. For Mac OS X 10.5 and 10.6, click [+]. Note ● If the machine is already shown in [ Printers ], select your machine, and click on [ - ] to delete.
- 112 - Printing from a Computer 5 Printing For Mac OS X 10.3.9 to 10.4.11 Memo ● The procedure below uses Mac OS X 10.4.11 as an example. The description may be different depending on your OS. 1 Prepare a USB cable. A USB cable is not supplied with your machine.
- 113 - Printing from a Computer 5 Printing 10 Click [ Add ]. If the [ You have no printers available ] dialog box is displayed, click [ Add ]. Note ● If the name of your machine whose [ connection ] is [ USB ] is already displayed, select it and click [ Delete ], and then click [ Add ].
- 114 - Printing from a Computer 5 Printing Starting a Print Job This section explains how to congure the print settings such as paper size, paper source, and media weight, and start printing on each printer driver you are using. Y ou need to install a printer driver on the computer before starting a print job.
- 115 - Printing from a Computer 5 Printing 6 Select a tra y from [ Paper Source ]. Memo ● If you select [ Automatically Select ] for a paper source, the tray with the designated paper t ype is automatically selected. 7 Click [ Advanced ]. 8 Click [ Paper Size ] and select a paper size from the drop-down list.
- 116 - Printing from a Computer 5 Printing 9 Select [ Paper input options ] from [ Feature Sets ]. 10 Select a media t ype from [ Media Type ]. Memo ● For gener al use, [ Use Printer Settings ] sufces for paper weight.
- 117 - Index A ActK ey .......................... 77, 78 C Component Name Machine ..................... 10 Operator P anel ............ 12 Conguration ...................... 21 Connection ADSL ......................... 28 Business Phone ..........
- 118 - Index Scanning ............................ 49 Sender Information.............. 33 Setup Information F orm ... 53, 61 Super G3 ............................ 35 T T ray Setting ........................ 20 T urning Off Machine ............. 18 T urning On Machine .
- 119 -.
www.okiprintingsolutions.com Oki Data Corporation 4-11-22 Shibaura, Minato-ku,Tokyo 108-8551, Japan 45002302EE Rev1.
Ein wichtiger Punkt beim Kauf des Geräts OKI MC562 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie OKI MC562 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für OKI MC562 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von OKI MC562 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über OKI MC562 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon OKI MC562 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von OKI MC562 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit OKI MC562. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei OKI MC562 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
