Benutzeranleitung / Produktwartung 425D des Produzenten Oki
Zur Seite of 137
okilogo.jpg global logo.jpg OKI POS 42 5D o425_72.jpg Developer’s Guide 59 33 6 30 1.
Document Title and Part Number OKIPOS 425D Developer ’ s Guide P/N 59336301 Disclaimer Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. Oki Data assumes no responsibility for the results of errors or omissions beyond its control.
| Developer’s Guide: English 3 Cont ents 1. Setting Up the Printer ....................................................................................................................................... 6 1.1. Select a Location .....................
4 OKIPOS 425D | 4. T r oubleshooting and Repair ................................................................................................. ......................... 5 8 4.1 Alarm Indication for a Failure ........................................
| Developer’s Guide: English 5 6. Command Description .................................................................................................................................... 9 5 6.1 Control Code List ....................................
6 OKIPOS 425D | 1. Setting Up the Print er 1.1. Select a Location · Firm, level surface capable of supporting approximately 7kg (15.4 lbs). · Clearance to open cover · At least 100mm (4 inches) add.
| Developer’s Guide: English 7 1.3 Unpacking Getting Started Check the contents: 1 Printer 2 Ribbon Cartridge If anything is missing or damaged, contact your dealer immediately .
8 OKIPOS 425D | 1.4 Installing the Printer Getting to Know the OKIPOS 425D o425_72.jpg 1 Printer Cover 2 Control Panel 3 Paper Guide 4 Cover Open Bar 5 ON/OFF Switch 2 5 4 3 1.
| Developer’s Guide: English 9 1.4.1 Remove the Shipping Restraints Important! Save the shipping restraints and packing materials in case you ever need to ship the printer . 1. Remove the five pieces of shipping tape. o425_30.jpg 2. Press the Cover open bar and open the printer cover .
10 OKIPOS 425D | 1.4.2 Setting the Interface Board Assembly 1.4.2.1 Setting the DIP Switches (RS-232C) A25001.doc Switch Settin g DIP SW Functi on ON OFF 1 Select s the data bit le ngth 7 bits 8 bits 2 Select s between th e presence and absence of parity bits.
| Developer’s Guide: English 11 1.4.2.2 Installing the Interface Board Assembly (1) Insert the Interface Board Assembly in the direction of the arrow .
12 OKIPOS 425D | 1.4.3 Connecting the Computer This printer supports either Parallel Interface or RS232C when the interface board is installed in the printer . T o install the interface board, refer to Section 1.4.2.2. 1. Check to be sure that the printer ’ s power is OFF .
| Developer’s Guide: English 13 1.4.7 Installing the Ribbon Cartridge 1. Make sure the printer is turned OFF . 2. Press the Cover open bar and open the printer cover .
14 OKIPOS 425D | 4 . Unpack the ribbon cartridge. Important! Do NOT remove the ribbon shield from the ribbon! o425_07.jpg 1 Ribbon Shield 2 T ake-up Knob 3 Grip Points 5. Install the new ribbon cartridge. 1) Hold the ribbon cartridge as shown below . o425_87.
| Developer’s Guide: English 15 3) Lower the front of the cartridge over the printhead until it snaps into place. o425_87.jpg and o425_88.jpg 4) T urn the knob (1) in the direction of the arrow on the cartridge to take up the ribbon slack.
16 OKIPOS 425D | 1.5 Installing the Paper Paper Specifications Maximum thickness: 0.3 mm (0.012 inches) A25002.doc Media Typ e Width Length Weight Number of copies Thickness D iameter Single p art (slip) 10 5 to 21 5. 9m m (4.13 ” to 8.5”) 70 t o 297mm (2.
| Developer’s Guide: English 17 1.5.1 Roll paper 1.5.1.1 Adjusting the Roll Paper Guide (Receipt) 1. Adjust paper guide A (1) to the paper width. Paper width: 2.75 inches (69.5 mm) or 3.00 inches (76.2 mm) Adjustment must be made for both Receipt and Journal.
18 OKIPOS 425D | 1.5.1.2 Loading the Roll Paper (Receipt) Use roll paper that matches the specifications. Note: The printer must be turned on before installing the roll paper . 1. Fold the paper so it is exactly straight and even (1), and will not tear off jaggedly (2).
| Developer’s Guide: English 19 5. Cut the roll paper . o425_92.jpg 6. Close the printer cover ..
20 OKIPOS 425D | 1.5.1.3 Adjusting the Roll Paper Guide (Journal) 1. Adjust paper guide B (1) to the paper width. Paper width: 2.75 inches (69.5 mm) or 3.00 inches (76.2 mm) Adjustment must be made for both Receipt and Journal. 1) When the printer is shipped, the paper width is set for wide roll paper (3 inch or 76.
| Developer’s Guide: English 21 1.5.1.4 Loading the Roll Paper (Journal) Use roll paper that matches the specifications. Note: The printer must be turned on before installing the roll paper . 1. Fold the paper so it is exactly straight and even (1), and will not tear off jaggedly (2).
22 OKIPOS 425D | 2) Insert the tip of roll paper into the groove of the rewinder as shown in the detail figure. Then, turn the rewinder into the arrow direction to wind the roll paper around it 2 or 3 times.
| Developer’s Guide: English 23 1.5.1.5 Adjusting the Roll Paper Near End Sensing Position The paper near end detector detects when the paper is almost gone by measuring the diameter of the Roll paper .
24 OKIPOS 425D | 1.5.2 Cut-Sheet Paper (Slip) 1.5.2.1 Loading the Cut-Sheet Paper (Slip) Use the paper that matches the specifications. Note: The printer must be turned on before loading the paper . 1. T urn on the printer . 2. Insert the paper as shown below , while butting the right edge of the paper against the paper guide.
| Developer’s Guide: English 25 1.5.3 Cut-Sheet Paper (V alidation/Stub) 1.5.3.1 Loading the Cut-Sheet Paper (V alidation/Stub) Use the paper that matches the specifications. Note: The printer must be turned on before loading the paper . 1. T urn on the printer .
26 OKIPOS 425D | How to remove the Piece 1. Press the Cover Open Bar and open the Printer Cover . CAUTION: Printhead may be very hot. o425_31.jpg and o425_32.jpg 2. Unlock the latch (1) of the Piece Cover B (2) and remove the Piece Cover B. o425_13.jpg 3.
| Developer’s Guide: English 27 4. Close Printer Cover . * Paper has been set for long-edge printing. o425_49.jpg * Store the removed Piece in a safe place so that you will not lose it.
28 OKIPOS 425D | 1.5.4 Sprocket Paper (T ractor) 1.5.4.1 Loading the Sprocket Paper (T ractor) Use the paper that matches the specifications. Note: The printer must be turned off before inserting the tractor . 1. T urn off the printer . Move the Paper Guide all the way to the right.
| Developer’s Guide: English 29 3. Set the tractor lever (1) in the direction of the arrow . o425_18.jpg 4. T urn on the printer . 5. Pull up on the lock levers (1) and open the tractor covers (2), then move the right tractor over to fit the width of the pape r.
30 OKIPOS 425D | 7. Move the left tractor to align the edge of the paper with the appropriate reference mark (!), and push back the right lock lever (2). o425_52.jpg 8. Fine-tune the position of the right tractor to center the holes in the paper on the pins, and push back the left lock lever (1).
| Developer’s Guide: English 31 9. Printer feeds the paper into the printer when your computer sends data. 10. Preparation 1) Position the printer at the front edge of the support (this promotes the unrestricted flow of paper into the printer), then place a stack of Sprocket (T ractor) Paper below the printer .
32 OKIPOS 425D | 2. Using the Print er 2.1 Operation Panel F unctions Note) OEM Fiscal T ype: The operation panel is under the control of the fiscal control PCB. Consequently , the fiscal control PCB should be removed before self tests. Alternatively , disconnecting the cable from the main control PCB is acceptable.
| Developer’s Guide: English 33 2.1.1 Switching Functions A25046.doc No. Switc h Functi on i n M od e s ot her tha n Tra ctor Functi on i n Tra c tor M ode 1S W 2 (FF/LOD,PAK) In Receipt Mod e: Feed.
34 OKIPOS 425D | 2.1.2 LED Function A25004.doc No. LED ON OFF Blinking 1 POWER Green Powered On Powered off - 2 LED 1 (ERROR) Red Recoverable Alarms *Slip Fee d/Eject Alarm *Auto L oad ing Ala rm *Aut.
| Developer’s Guide: English 35 2.2 Local F unctions Note OEM Fiscal T ype : This section describes local maintenance capabilities under the control of the printer block. The fiscal control PCB should be removed before the functions are performed. 2.
36 OKIPOS 425D | 2.2.2 Star ting A25047.doc No. Loca l F unct ions SW2 SW3 SW1 SW4 1 All letters & rolli n g ASCII continuous pri nting test (Receipt) XXO X 2 All letters & rolli n g ASCII con.
| Developer’s Guide: English 37 2.3 Menu F unction (Receipt) Overview The menu function is the local function that sets each mode to control the printer and adjust it.
38 OKIPOS 425D | 2.3.2 OKI — Standard Model A25007.doc No. Item Function Sets 1 Auto Cutter Unit Selects A uto Cutter Un it Installed/Not Installed O Yes No 2 MICR Unit Selects MICR Unit Installed/N ot Installed Ye s(CMC-7) Yes(E-13B) O No 3 Print Registration Adjusts the print position i f it shifts in Forward pr inting and Rever se pri nting 0.
| Developer’s Guide: English 39 2.3.3 How to Operate Start T o start the Menu Mode, turn the printer on while holding down SW2 + SW1. When the printer’ s initialization ends correctly , the printer prints the title “Menu Print” and all the menu items and set values.
40 OKIPOS 425D | 2.4 Hex Dump F unction (Receipt) This function converts received data, as it is, to character codes, and prints it in the Receipt mode. The printed contents ar e as follows: Upon receiving one byte, the printer divides it into three characters, High-nibble, Low-nibble and a space.
| Developer’s Guide: English 41 2.5 Using the M ICR Reader If your printer has the factory installed optional MICR (Magnetic Ink Character Recognition) reader that enables the printer to read and process MICR characters on personal checks, read this section.
42 OKIPOS 425D | How to use the MICR Reader 1. Send the command “FS a 0 n” from the host computer. Then the printer shifts to the MICR Mode and waits for the Check Sheet to be inserted. LED3 blinks slowly in orange (repeats 1 sec ON, 1 sec OFF). 2.
| Developer’s Guide: English 43 2.6 M ICR Read T est (Receipt) This function performs MICR read and prints that result on the receipt paper. Ef fective only when the MICR unit is installed and “MICR Unit = Y es(CMC-7)” or “MICR Unit = Y es(E-13B)” is set in the menu.
44 OKIPOS 425D | (4) Contents printed When Read is OK: (a) Prints “Read OK.” (b) Prints the MICR read results in HEX dump. (“XX XX ...... XX” + ASCII: 1 line contains 8 byte information) When Read is NG: (a) Prints “Read NG.” (b) Prints the MICR read results (Return Code (1 byte) and read data) in HEX dump.
| Developer’s Guide: English 45 2.7 Rewinder Winding Evaluation Continuous Print T est (Journal) This function performs print/platen switch continuous test to evaluate the rewinder winding performance. (1) How to start T urn the power on while holding down SW3 + SW1 + SW4.
46 OKIPOS 425D | 2.8 Using the Auto Cutter This printer is equipped with an Auto Cutter . Follow the procedure below to automatically cut the Roll Paper (Receipt). Note 1: Make sure that “Auto Cutter Unit” items in the menu are set to “Y es.” If there are any “No” items, change them to “Y es.
| Developer’s Guide: English 47 3. Maint enance 3.1 Replacing the Ribbon Cartridge When printing becomes light, replace the Ribbon Cartridge, following the procedure shown below: 1. Make sure the printer is turned OFF . 2. Press the Cover open bar and open the printer cover .
48 OKIPOS 425D | 4. Swing the front of the cartridge up off the printhead, then lift the cartridge out and discard it. Caution! The printhead may be HOT! o425_87.jpg 5. Unpack the ribbon cartridge. Important! Do NOT remove the ribbon shield (1) from the ribbon! o425_07.
| Developer’s Guide: English 49 3) Lower the front of the cartridge over the printhead until it snaps into place. o425_87.jpg and o425_88.jpg 4) T urn the knob (1) in the direction of the arrow on the cartridge to take up the ribbon slack.
50 OKIPOS 425D | 3.2 Replacing the Roll Paper When the Roll is used up, load a new one, following the procedure shown below . 3.2.1 Roll Paper (Receipt) 1. Press Form Feed switch (1) on Receipt side so that the whole Receipt Paper (2) is ejected. o425_62.
| Developer’s Guide: English 51 3.2.2 Roll Paper (Journal) 1. Make sure that the media mode is set to one of the following: Receipt mode, journal mode, or Receipt + Journal mode. If not, set to one of the above modes. For mode switching, refer to Section 2.
52 OKIPOS 425D | 4. Remove the paper roll (Journal) on the rewinder following the procedure below . (1 ) Remove the rewinder (1) from the printer. (2 ) Rotate the flange (2) in the direction shown below and remove it from the rewinder . Note 1: Rotation direction of the flange varies depending on the width of the Roll Paper .
| Developer’s Guide: English 53 3.3 Clearing Paper Jams When Roll Paper gets jammed, remove the paper , following the procedure shown below: 1. Press Cover Open Bar and open the printer cover . * Print head may be very hot. Exercise caution. o425_31.
54 OKIPOS 425D | 3. Press the two levers (1) on either side at the same time as shown, lift the plate assembly and gently pull out the jammed paper in the direction of the arrow . Note: Be careful not to leave small pieces of paper . o425_76.jpg and o425_77.
| Developer’s Guide: English 55 2. Remove the rewinder and cut the paper at the positions (1). o425_75.jpg 3. Press down the two levers shown below simultaneously , lift up the plate assembly , and gently pull out the paper (Journal) in the direction shown below .
56 OKIPOS 425D | 5. Gently remove the paper left on the Auto Cutter . Note: When the blade of the Auto Cutter is exposed, turn the knob (1), and manually move the blade to the original position. o425_79.jpg Note: T urn on the power . If the Auto Cutter behaves abnormally , contact your shop or maintenance service.
| Developer’s Guide: English 57 Sprocket Paper When sprocket paper gets jammed, remove the paper , following the procedure shown below . 1. Open the Tractor Cover (1) and cut the sprocket paper at the perforation (2). o425_57.jpg 2. Press the Cover Open Bar and open the printer cover o425_31.
58 OKIPOS 425D | 4. T roubleshooting and Repair 4.1 Alarm Indication for a Failure When a failure occurs, the printer indicates its contents with LED1 lamp on the operation panel, which blinks in different ways depending on the failure type. Note: OEM Fiscal Type: The alarm indication works only when the Fiscal Control PCB is not mounted.
| Developer’s Guide: English 59 4.1.1 Details of Alarm Indications T able411.doc No. o f times LED 1 blinks Mal f uncti on conte nts What you should do 1 P rogram ROM Ala rm 2 EEPROM Alarm 3 I nter .
60 OKIPOS 425D | 4.1.2 LED Indication T able412.doc No. LED ON BLINK 1 LED 1 (ERROR) R ed [Recoverable Alar ms] Slip Lo ad Alarm → Slip pa pe r w a s no t l oade d cor r e ct ly. Re m ove it a nd relo ad i t. Slip Ex it Alarm → Slip pap er d id no t exit correctly.
| Developer’s Guide: English 61 5. Specifications 5.1 Introduction 5.1.1 Scope of Application This specification applies to OKIPOS 425D/425D/425DF , a 9-pin type serial dot impact printer . This device is a desk-top serial dot impact printer , used exclusively as the output device for POS (Point-of-sales) system.
62 OKIPOS 425D | Options 1 Front Tractor: User Option o425_26.jpg 2 Parallel Interface: Dealer Option (OKI/OEM Standard T ype) o425_23.jpg 3 RS-232C Interface: Dealer Option (OKI Standard T ype) o425_81.jpg Note Only one interface option can be installed.
| Developer’s Guide: English 63 5.1.3 Configuration Standard Printer Configuration 1 Printer Cover 2 Control Panel 3 Paper Guide 4 Cover Open Bar 5 ON/OFF Switch o425_72.
64 OKIPOS 425D | 5.2 General Specifications 5.2.1 Power Requirements 1 Input power Single-phase AC V oltage: Universal 120V AC +15% – 230V AC +15% Frequency: 50/60Hz +2% 2 Power consumption (without Fiscal Control PCB) Local T est : Max. 40W (Local Printing) Idle: Max.
| Developer’s Guide: English 65 5.3 Communication Interface Specifications 5.3.1 Parallel Int erface (OKI/OEM Standard T ype) 1 Interface Spec (Between centronics connector and host PC) Parallel interface signal part (IEEE-1284 parallel equivalent) Centronics Connector Pin Assignment signal A25012.
66 OKIPOS 425D | 5.3.2 RS-23 2C Int er face (OKI Standard T ype) 1 Interface signals A25013.doc Pin No. Signal Code Signal Function 1 Protect ive ground PG - F rame ground 2 Transmitted Data TD From p.
| Developer’s Guide: English 67 5.3.3 Cash Drawer connector (OKI Standard T ype) 1 Cash Drawer Connector Signals A25014.doc Pin No. Signal Name Direction Function 1 FG - Frame ground 2 CASHDV1 To Ca.
68 OKIPOS 425D | 5.3.4 Customer Display connector (OKI Standard RS-23 2C Interface T ype) 1 Customer Display Connector Signals A25015.doc Pin No. Signal Name Direction Function 1 FG - Frame ground 2 N.
| Developer’s Guide: English 69 5.4 Physical Characteristics 5.4.1 Printhead Print method: Impact dot matrix Number of dot wires: 9 wires Dot wire diameter: 0.34 mm (0.013") 5.4.2 Printer 1 Outside dimensions (without Tractor) 265 mm (10.43") (W) x 218 mm (8.
70 OKIPOS 425D | 5.5 Logical Characteristics 5.5.1 Print Direction Bidirectional, unidirectional printing Short-line-seeking printing 5.5.2 Selectable Character Pitches Character width A25016.doc Selected font HSD Utility HSD (*1) Utility (*1) Regular size 20 CPI 0.
| Developer’s Guide: English 71 5.5.4 Font Size/Cell Size A25019.doc Font type Font size ( H x V) Cell size (H x V) CPI HSD 7 x 7 dots 9 x 9 dots 20 ( 26. 7 * 1) Utility 9 x 7 d ots 11 x 9 dots 16.4 (2 1.8 *1) (*1) OE M Ty pe is Se lect C ut She e t or Spr ocke t pa per ( Tra c tor) m ode onl y.
72 OKIPOS 425D | 5.7 Media Specifications 5.7 .1 Cut-Sheet P aper (Slip/V alidation) Paper W idth: 105 to 215.9 mm (4.13" to 8.5") Paper Length: 70 to 297 mm (2.76" to 11.7") Single part (Slip) W eight: 52 to 105 g/m 2 (14 to 28 lb) Thickness: 0.
| Developer’s Guide: English 73 5.7 .5 Appendix: Media Specifications 5.7 .5.1. Cut-Sheet Paper (Slip/V alidation) 5.7.5.1.1. Paper Size and Printing Area 1 Single-part Paper OP425_10.eps 1 Base line 2 First character position 3 Paper inserting direction 4 Against the perpendicular to the Base line 5 Printing area 6 + 0.
74 OKIPOS 425D | 2 Counterfoil and Stub OP425_11.eps 1 Printing area 2 Stub 3 Inserting direction A25023.doc Symbol Designat i on Stan da rd Va l ue W Paper width 70mm (2.76 inch) o r more L Paper leng t h 40mm (1.57 inch) o r more A Print s tar tin g po siti on 18mm ( 0.
| Developer’s Guide: English 75 3 Multi-part Paper The standard multi-part paper is the one whose top edge is pasted. OP425_13.eps 1 Pasted securely (1mm) 5 Paper inserting direction 2 Base line 6 Printing area 3 First character position 7 Against the perpendicular to the Base line 4 Printing surface 8 + 0.
76 OKIPOS 425D | 5.7.5.1.2 Paper Quality The paper in the following quality may be used. A25025.doc Type Pa pe r Qua lit y Single -par t pa per and St ub High qual it y pape r Multi-part paper Pressure-sensitive paper, Carb on-lined paper 1 Paper smoothness must be 90 ~ 7 sec.
| Developer’s Guide: English 77 5.7.5.1.5 Binding Holes Do not use a paper with punched holes. It may invalidate your warranty . If you choose to use punched paper , be sure to test it thoroughly . Follow these guidelines: 1 Do not print within 5 mm of the hole center .
78 OKIPOS 425D | 5.7.5.1.6 Perforated Lines Do not use paper with perforations. It may invalidate your warranty . If you choose to use perforated paper , be sure to test it thoroughly . Follow these guidelines: 1 The specification of a perforated line corresponds to that of a perforated line on Sprocket Paper .
| Developer’s Guide: English 79 5.7.5.1.7 Provisions on Fold, Bend and Curl on Cut-sheet Paper Paper is apt to sustain bends, cambers or curls resulting from manual handling, carrying, stacking, storing conditions, etc. Therefore, before printing, check and adjust paper in accordance with the provisions below to eliminate paper feed problems.
80 OKIPOS 425D | 5.7 .5.2. Roll paper (Receipt/Journal) 5.7.5.2.1 Paper size and Printing area OP425_19b.eps 1 First character position 2 Cutting position (for manual cutting) 3 Printing area A25048.doc Symbol Designatio n Standard Value W Rol l pa per w i dth 69.
| Developer’s Guide: English 81 5.7.5.2.2 Paper Quality Paper of the following quality may be used. A25049.doc Type Paper Qua lit y Single-pa rt pa pe r High qualit y paper 1 Paper smoothness must be 90 ~ 7 sec. for Beek and 75 ~ 300 sec. for Sheffield.
82 OKIPOS 425D | 5.7 .5.3. Sprocket Paper (T ractor) 5.7.5.3.1 Paper size and Printing area OP425_20.eps 1 Printing area 2 Printable area 3 First character position 4 Paper inserting direction 5 Unit: mm 6 Maximum 160.02 The specification for the printable area differs from that for the printing area.
| Developer’s Guide: English 83 Symbol Designatio n Sta n dard Va lue W Pa per w i dth 76. 2~21 5.9mm (3~ 8.5 inc h) L Paper lengt h 76.2~ 355. 6m m ( 3~ 14 inc h) The length mus t be the one obtained via multipl ying 25.4m m (1 inc h) by a n inte ger A Headi ng positi on 10.
84 OKIPOS 425D | 5.7.5.3.2 Paper Quality Paper of the following quality may be used. A25031.doc Type Paper Quali ty Single - par t pa per Hig h qual it y pa pe r Multi-part paper Pressure-sensitive paper, Carbon-lined pap er or Interleaved pap er (1) Note 1 Interleaved paper is a multi-part paper with carbons inserted between copies.
| Developer’s Guide: English 85 5.7.5.3.4 Fixing Method of Multi-part Paper Joint The joint fixing method for a multi-part paper shall be spot-pasting, line-pasting or crimping. Spot pasting is the proper precaution against position deviation made when piling sheet tiers.
86 OKIPOS 425D | 3 Crimping a Crimp paper on both right/left sides. b Apply crimping from the front surface, making no protrusion on the surface. c All the sheets must be engaged securely with each other at the crimp position free of lifting.
| Developer’s Guide: English 87 5.7.5.3.5 Rising in Horizontal Perforated Line Protrusions in a horizontal perforated line may result in poor print quality , unstable paper feeding or frequent paper jam. Therefore, the rising height must be kept within 1mm.
88 OKIPOS 425D | 5.7.5.3.7 Binding Holes Do not use a paper with punched holes. It may invalidate your warranty . If you choose to use punched paper , be sure to test it thoroughly . Follow these guidelines: 1 Do not print within 5 mm of the hole center .
| Developer’s Guide: English 89 5.7.5.3.8 Corner Cut Do not use paper with corner cuts. It may invalidate your warranty . If you choose to use corner cut paper , be sure to test it thoroughly . Follow these guidelines: 1 Do not print within the shaded area adjoining a corner cut.
90 OKIPOS 425D | 5.7.5.3.9 Wrinkle, Pleat and Swell Use paper , which has been folded zigzag on horizontal perforated lines, free of wrinkles and pleats. Newly unpacked paper often has wrinkles or pleats on the first and last pages. Please eliminate pages having wrinkles and pleats before printing.
| Developer’s Guide: English 91 5.7 .5.4. M ICR (only with M ICR T ype) 5.7.5.4.1 Paper Size and Scanning Area OP425_30.eps 1 Paper inserting direction 2 Scanning Area A25033.doc Symbol Designatio n Stan da r d Val ue W P a pe r wi dth 76~7 8mm ( 2.
92 OKIPOS 425D | 5.8 Paper Feed Specifications 5.8.1 Paper feed methods/Paths a Friction feed For Cut-sheet paper b Friction feed For Roll paper c Push tractor feed (Front path) For Sprocket paper (Tractor) 5.8.2 Paper Positioning Restrictions OP425_31.
| Developer’s Guide: English 93 5.9 MICR Specifications (Only with MICR type) 5.9.1 Available Fonts E-13B and CMC7 (can be selected command) 5.9.2 Scanning Speed 9.
94 OKIPOS 425D | 5.1 0 Auto Cutter Specifications Structure This cutter unit has a driving part. Its mechanism cuts recording paper partially (1 point remains) or fully , depending on the motor driving direction that a user chooses. The movable blade cuts the recording paper by sliding.
| Developer’s Guide: English 95 6. Command Description 6.1 Control Code List 6.1.1 OEM — Standard Model 6.1.1.1 Function Code 1 List of Function Codes A25037.
96 OKIPOS 425D | 6.1.1.2 ESC Sequence 1 Command recognition A code subsequent to an ESC code is handled as a 7-bit code. (MSB=0) An ESC code that is followed by a functional code (except ESC CR) is handled as a single functional code. If the ESC codes follow each other , they are treated as one ESC code.
| Developer’s Guide: English 97 6.1.1.3 GS sequence 1 Command recognition GS codes in combination are handled the same way that ESC codes are handled. 2 GS Sequence table A25039.doc No. HEX Comma nd Seq uence Function s Print St art 1 1D 45 GS E n To sele c t pr int spee d and print hea d cur re nt flow time.
98 OKIPOS 425D | 6.1.2 OKI Standard Model 6.1.2.1 Function Code 1 List of Function Codes A25040.doc No. HEX DEC CODE Remarks Print Start 1 0A 10 L F Print/line feed O 2 0C 12 FF Eject Cut Sheet paper .
| Developer’s Guide: English 99 6.1.2.2 ESC Sequence 1 Command recognition ESC codes in combination are handled the same way that DLE codes are handled.
100 OKIPOS 425D | 46 1B 6D ESC m Partial cut (keepin g o ne point unc ut) X 47 1B 7 0 ESC p m t1 t2 Generates designated pu lse (Open Cash Drawer) X 48 1B 74 ESC t n Selects character code table X 49 .
| Developer’s Guide: English 101 6.1.2.3 FS Sequence 1 Command recognition FS codes in combination are handled the same way that DLE codes are handled.
102 OKIPOS 425D | 6.2 Character Set 6.2.1 Code table (OEM — Standard T ype) The character code tables follow . 6.2.1.1 USA OP425_03.tif 1 0xH and 1xH are Control Code areas. 2 If a code received is other than a control code in 0xH and 1xH, it is ignored.
| Developer’s Guide: English 103 6.2.1.2 Canada-French OP425_04.tif 1 0xH and 1xH are Control Code areas. 2 If a code received is other than a control code in 0xH and 1xH, it is ignored. 3 The above table assumes international character set is set to “American.
104 OKIPOS 425D | 6.2.1.3 Multilingual OP425_05.tif 1 0xH and 1xH are Control Code areas. 2 If a code received is other than a control code in 0xH and 1xH, it is ignored. 3 The above table assumes international character set is set to “American.” 4 The blank space (20H, 7FH, FFH) indicates a space code.
| Developer’s Guide: English 105 6.2.1.4 Portugal OP425_06.tif 1 0xH and 1xH are Control Code areas. 2 If a code received is other than a control code in 0xH and 1xH, it is ignored. 3 The above table assumes international character set is set to “American.
106 OKIPOS 425D | 6.2.1.5 Norway OP425_07.tif 1 0xH and 1xH are Control Code areas. 2 If a code received is other than a control code in 0xH and 1xH, it is ignored. 3 The above table assumes international character set is set to “American.” 4 The blank space (20H, 7FH, FFH) indicates a space code.
| Developer’s Guide: English 107 6.2.1.6 BRASCII OP425_08.tif 1 0xH and 1xH are Control Code areas. 2 If a code received is other than a control code in 0xH and 1xH, it is ignored. 3 The above table assumes international character set is set to “American.
108 OKIPOS 425D | 6.2.1.7 Abicomp OP425_09.tif 1 0xH and 1xH are Control Code areas. 2 If a code received is other than a control code in 0xH and 1xH, it is ignored. 3 The above table assumes international character set is set to “American.” 4 The blank space (20H, 7FH, A0H) indicates a space code.
| Developer’s Guide: English 109 6.2.1.8 Multilingual 858 OP425_10.tif 1 0xH and 1xH are Control Code areas. 2 If a code received is other than a control code in 0xH and 1xH, it is ignored. 3 The above table assumes international character set is set to “American.
110 OKIPOS 425D | 6.2.1.9 ISO 885 9/1 5 OP425_11.tif 1 0xH and 1xH are Control Code areas. 2 If a code received is other than a control code in 0xH and 1xH, it is ignored. 3 The above table assumes international character set is set to “American.” 4 The blank space (20H, 7FH, A0H) indicates a space code.
| Developer’s Guide: English 111 6.2.1.1 0 International charact er set table A25044.doc ESC R n C ountr y 23 2 4 26 40 4F 5B 5C 5D 5E 5F 60 7B 7C 7 D 7E 0 ( 0 0 ) H A m e r i c a n # $ & @ O [ .
112 OKIPOS 425D | 6.2.2 Code table (OKI — Standard T ype) The character code tables follow . 6.2.2.1 USA OP425_12.tif 1 0xH and 1xH are Control Code areas. 2 If a code received is other than a control code in 0xH and 1xH, it is ignored. 3 The above table assumes international character set is set to “American.
| Developer’s Guide: English 113 6.2.2.2 Canada-French OP425_13.tif 1 0xH and 1xH are Control Code areas. 2 If a code received is other than a control code in 0xH and 1xH, it is ignored. 3 The above table assumes international character set is set to “American.
114 OKIPOS 425D | 6.2.2.3 Multilingual OP425_14.tif 1 0xH and 1xH are Control Code areas. 2 If a code received is other than a control code in 0xH and 1xH, it is ignored. 3 The above table assumes international character set is set to “American.” 4 The blank space (20H, 7FH, FFH) indicates a space code.
| Developer’s Guide: English 115 6.2.2.4 Portugal OP425_15.tif 1 0xH and 1xH are Control Code areas. 2 If a code received is other than a control code in 0xH and 1xH, it is ignored. 3 The above table assumes international character set is set to “American.
116 OKIPOS 425D | 6.2.2.5 Norway OP425_16.tif 1 0xH and 1xH are Control Code areas. 2 If a code received is other than a control code in 0xH and 1xH, it is ignored. 3 The above table assumes international character set is set to “American.” 4 The blank space (20H, 7FH, FFH) indicates a space code.
| Developer’s Guide: English 117 6.2.2.6 BRASCII OP425_17.tif 1 0xH and 1xH are Control Code areas. 2 If a code received is other than a control code in 0xH and 1xH, it is ignored. 3 The above table assumes international character set is set to “American.
118 OKIPOS 425D | 6.2.2.7 Abicomp OP425_18.tif 1 0xH and 1xH are Control Code areas. 2 If a code received is other than a control code in 0xH and 1xH, it is ignored. 3 The above table assumes international character set is set to “American.” 4 The blank space (20H, 7FH, A0H) indicates a space code.
| Developer’s Guide: English 119 6.2.2.8 Multilingual 858 OP425_19.tif 1 0xH and 1xH are Control Code areas. 2 If a code received is other than a control code in 0xH and 1xH, it is ignored. 3 The above table assumes international character set is set to “American.
120 OKIPOS 425D | 6.2.2.9 ISO 885 9/1 5 OP425_20.tif 1 0xH and 1xH are Control Code areas. 2 If a code received is other than a control code in 0xH and 1xH, it is ignored. 3 The above table assumes international character set is set to “American.” 4 The blank space (20H, 7FH, A0H) indicates a space code.
| Developer’s Guide: English 121 6.2.2.1 0 International charact er set table A25045.doc E S C R n C o u n t r y 2 32 42 64 04 F 5 B 5 C 5 D 5 E 5 F 6 07 B 7 C 7 D 7 E 0( 0 0 ) H A m e r i c a n #$&.
122 OKIPOS 425D | 7 . Using the Unitool Print er Driver 7 .1 Setting Slip Paper in the P aper T ray This section describes the method to set Slip paper in the input bin. W ith this printer, the position of the Paper Guide can be adjusted sideways, enabling you to change the paper setting position.
| Developer’s Guide: English 123 7 .1.1 Using Registered Paper Icons 1 Paper width is 190.5 mm (7.5") or more and up to 215.9 mm (8.5") inclusive. O425_108.jpg 1 Printing area 2 Left Margin 27.94mm (1.1 inch) 3 Right Margin 27.94mm (1.1 inch) 4 Printable Maximum Width 160.
124 OKIPOS 425D | For paper that is 190.5 mm (7.5") or more and less than 215.9 mm (8.5"), slide the Paper Guide toward the left as needed so tha t the entire printing area on the paper shifts toward the right, as illustrated below . O425_109.
| Developer’s Guide: English 125 2 Paper W idth is less than 190.5 mm (7.5"). The printing area, when printing paper that is less than 190.5mm (7.5") in width, is illustrated below . For paper 190.5 mm (7.5") or more and less than 215.
126 OKIPOS 425D | 7 .1.2 Using Custom Size Custom Size is variable in width in the range of 187.96 mm (7.4") - 215.9 mm (8.5"). 7 .1.2.1 Using Paper Size that is less than 1 8 7 .96 mm (7 .4") in W idth T o adjust the left and right margins and create data for a paper size you want to use, follow the procedure below .
| Developer’s Guide: English 127 Set the right margin at 27.94 mm (1.1") (Printing disabled area 25.4 mm [1.0"] + Slip paper’ s minimum right mar gin 2.54 mm [0.1"]) or more. Image of actual printing area O425_112.jpg 1 T arget Printing Area 2 Printing Area with margin adjusted 3 Left margin for paper to be used 2.
128 OKIPOS 425D | 4 W ith the Paper Guide pushed to the right, insert 101.6 mm (4.0")-wide paper to print. o425_119.jpg 1 T arget Printing Area 2 Printable Maximum W idth 160.02mm (6.3 inch) 3 Slip Tray Left Side 4 Slip Tray Right Side 5 Paper Guide 6 Right Margin 27.
| Developer’s Guide: English 129 c W ith the Paper Guide pushed to the left, insert 101.6 mm (4.0")-wide paper to print. An image of actual printing area o425_112.jpg 1 T arget Printing Area 2 Printing Area with margin adjusted 3 Left margin for paper to be used: 2.
130 OKIPOS 425D | W ith Paper Guide pushed to the left, insert 101.6 mm (4.0")-wide paper to print. O425_113.jpg 1 T arget Printing Area 2 Printable Maximum W idth 160.
| Developer’s Guide: English 131 7 .1.2.2 Using Paper Size that is 1 8 7 .96 mm (7 .4") or more and less than 21 5.9 mm (8.5") in width Custom Size is variable in width in the range of 187.96 mm (7.4") - 215.9 mm (8.5"), but when the designated width is more than 187.
132 OKIPOS 425D | 7 .2 About the V alidation Printing Area This section describes the information for the V alidation printing area, and it includes notes for using V alidation. 1 In V alidation mode, you can use the same paper as in Slip mode, but the printing area is not the same as that of Slip mode.
| Developer’s Guide: English 133 6 The following shows examples of print data created in W indows applications in each Paper source (L_Alignment/Center/ R_Alignment).
134 OKIPOS 425D | 7 Basically , the concept of setting the printing area in the horizontal direction and the margins for Custom paper is the same as for Slip, except for the following. Custom Size is variable in width in the range of 162.56 mm (6.4") - 215.
| Developer’s Guide: English 135 7 .3 Setting T ractor Paper in the T ractor Unit This section describes how to set Tractor Paper in the Tractor Unit. The maximum printable width per line with Tractor paper is 160.02 mm (6.3"). Push the T ractor Paper Guide against the Right T ractor Unit’ s right edge when using this print driver .
136 OKIPOS 425D | 7 .5 Special functions of the Windows 95/98 V ersion Printer Driver The following dialog shows the Paper tab of the W indows 95/98 printer driver . The Unprintable Area function does not exist in the driver property setting for the NT4 environment.
| Developer’s Guide: English 137 The application judges that the top 1 inch of “T op Margin 2 inches” is the printer’ s mechanical Auto Loading position, therefore the application does not produce data for the actual data transfer . Thus, the application produces data while ignorin g the data in the first 1 inch from the top of that data.
Ein wichtiger Punkt beim Kauf des Geräts Oki 425D (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Oki 425D noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Oki 425D - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Oki 425D reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Oki 425D erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Oki 425D besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Oki 425D verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Oki 425D. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Oki 425D gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
