Benutzeranleitung / Produktwartung NV-E6DMS-DC des Produzenten Nuvo
Zur Seite of 29
.
ENGLISH Danger Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably to noise induced hearing loss but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time.
FRENCH DURE EN HEURES P AR JOUR 8 6 4321 INIVEAU SONORE CONTINU EN dB 90 93 95 97 100 103 Danger L‘exposition a des niveaux eleves de bruit peut provoquer une perte permanente de l’audition, Chaqu.
Introduction Congratulations on your purchase of the NuV o Essentia System. Essentia brings the best of today' s digital technology to a true whole- home audio system. Listening to multiple audio sources from independent zones throughout the home has never been easier or more affordable.
POWER STAND BY ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 1 2 3 V .II Essentia Front P anel 1. POWER Button: 2. ST AND BY LED: 3. Zone Status LED's: The amplifier is designed to be turned on and remain on. The power button supplies power to the system.
Essentia Back P anel 1. Audio Source Inputs: 2. Source Link: 3. V ariable Lineout: 4. Fixed Lineout: 5. Speaker Outputs: 6. Zone T riggers: 7 . Emitter Outputs: 8. System On: 9. External Mute: 10. Network Input: 11. Digital Link: 12. RS232 Port: 13. AC Power: The Essentia amplifier accepts up to six audio sources.
1. Setup: 2. Whole-Home Control: 3. T ransport Buttons: 4. Video Source Control: 5. Source V olume: 6. Numeric Buttons: 7 . Power Button: 8. Channel up and down: 9. Macro Buttons: The setup button is used to place the remote control in program/learn mode.
7 Inst alling the Essen tia Sy stem in Y our Home I. Prewire The Essentia System uses CA T5 cable for keypad control and either two or four-conductor 16-gauge speaker wire. All the wire is “homerun” from each zone to the location of the Essentia amplifier and Audio Source equipment.
II. T erminating Speaker Wire Be careful not to allow the exposed wire from each conductor to touch the adjacent conductor . This will short the speaker input. Each speaker output is designed for two 8-Ohm speakers. Overloading the amplifier could cause it to overheat and do damage to the output.
IV . Connecting the EZ Port to the Essentia amplif ier When the EZ P ort is installed in the wall the only part visible should be the faceplate and a single RJ45 jack. The supplied pre- terminated network cable can then be plugged into the jack on the EZ P ort and into the network connection on the back of the Essentia amplifier , Fig.
VII. Expanding Essentia to 12 Zones Six additional listening zones can be added to the Essentia System using the Essentia Expander package. The expansion is easily done using the Source Link and Digital Link multi-pin outputs on the Essentia main amplifier , Fig.
EQ Control and Source Grouping T o change bass response, press the Mute button and Source 1 button simultaneously. Adjust the bass level up or down by using the V olume Up and V olume Down buttons. The volume indicator LEDs will indicate the output level, fig.
All On/P arty Mode The Essentia System has an All On feature. Any keypad within the system, which can be up to twelve zones, has the ability to become a master control for the entire house. The master keypad will control zone on, volume level, and source selection for all other zones.
13 X. Using the Fixed and V ariable Lineouts Zone V ariable Lineout Each zone of the Essentia amplifier has two 3.5mm mini stereo outputs. These are fixed and variable lineouts used for adding additional amplification when necessary for each zone.
Zone Fixed Lineout In some zone applications, it is more advantageous to have a separate volume control on the additional speakers being driven by an additional amplifier . This is common with outdoor zones. The fixed lineout offers the capability to add amplification, but the audio signal is not affected by the zone keypad volume level.
15 XI. The NV-LRC1 IR Remote Control The Essentia System comes with the NV-LRC1 Learning Remote Control. This remote allows wireless control of all keypad functions, as well as the functions of the audio source equipment.
16 XIII. NV-LSA40 Local Source Amplif ier The LSA40 is 40 watt accessary amplifier that allows any line-level audio signal local to a zone to be amplified through that zone ’ s speakers. It is designed to be used universally in a variety of applications, but as shown in fig.
XIV . NV-LSA40PD Local Source Amplifier P ower Distribution Hub The LSA40PD is a great device for distributing the necessary DC power to up to 4 individual L SA40 amplifiers. This allows the L SA40 components to be remotely located without the need for an external power supply in the zone, fig.
18 XV . NV-LSI12 Local Source Interrupt A lower cost alternative to the LSA40 is the L SI12. This is a non-amplified local source interrupt. It is installed in the same way the LSA40 is installed, but the incoming local signal must be amplified, fig 20.
19 XVI. NV-P2100 200 W att Auxiliary Amplifier The P2100 is specifically designed for use with the NuV o Systems ' lineouts. It can be used with either the fixed or variable lineouts on the Essentia with either a 1/8” (3.5mm) to 1/8” stereo patch cable or a 1/8” stereo to RCA patch cable, Fig 21.
20 T roubleshooting When the keypad is plugged in there is a loud pop through the speakers and the keypad does not work. Improperly wired CA T5 cable. Check that you are using the 568A or B wiring standard (see section I: Crimping CA T5 wire). The best way to know is to use a CA T5 tester .
21 Specifications Zones 1-6 Power A mplifie r Outputs Zone Trigger Outputs Continuous Average Output Power 40W (20W x 2) Output Power 12V @ 50m A Two channels driven 30-20kHz @1% T HD Outputs 6 (zones 1-6) Rated Distortion (1/2 power) 0.
22 Addendum Control Interface Description Document for the Nuvo E6D Main Unit * # #?<CR>” *IRSETSR<CR> #IRSET :aa,bb,cc,dd,ee,ff<CR> Revision E (for Nuvo E6D Mark II systems only) June 8, 2006 Nuvo T ransmit to System Controller on pin 2.
NOTE: the Main Unit ships with the carrier frequency DEF AUL T setting of 38 KHz for all six sources. ********************************************************************************* COMMAND: Restores DEF AUL T SOURCE IR carrier frequency settings (38 KHz for all six sources).
MUTE input, however , will always override other volume response values with the “XM” response. ********************************************************************************* COMMAND: * ZoneSet ST A TUS REQUEST where xx is zone # from 1 to 12.
Command to determine when the desired volume point has been reached. Note that ramps in different zones may start at different levels and will all ramp at the same rate. ********************************************************************************* COMMAND: * Ramp ALL zones DOWN at a 10 dB/second rate in 1 dB steps.
********************************************************************************* COMMAND: * zone xx MUTE OFF (returns zone output to currently connected source at previous volume setting).
********************************************************************************* COMMAND: * zone xx KEYP AD LOCK ON This will REST ORE ALL keypad control input on the zone (useful as Parental lock control) . This is the same as deactivating the Parental lock control at a keypad by holding down a SOURCE key for three seconds).
ESS513 0706.
Ein wichtiger Punkt beim Kauf des Geräts Nuvo NV-E6DMS-DC (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Nuvo NV-E6DMS-DC noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Nuvo NV-E6DMS-DC - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Nuvo NV-E6DMS-DC reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Nuvo NV-E6DMS-DC erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Nuvo NV-E6DMS-DC besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Nuvo NV-E6DMS-DC verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Nuvo NV-E6DMS-DC. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Nuvo NV-E6DMS-DC gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
