Benutzeranleitung / Produktwartung RCA3 des Produzenten Niles Audio
Zur Seite of 24
T ABLE OF CONTENTS Introduction 2 Getting Started 4 Installation 4 System Operation 13 Optional Accessories 14 Running Sensor Cable in New Construction 16 Concealing Sensor Cable in Existing W alls 18.
R EMO TE C ONTR OL A NYWHERE ! K IT 2 Introduction The Remote Control Anywhere! Kit enables you to operate your remote con- trolled audio/video equipment from vir- tually any location.
R EMO TE C ONTR OL A NYWHERE ! K IT 3 T ools Needed • Pencil • Standard screwdriver • Phillips screwdriver • Wire strippers • Drill (and assorted bits) DS00408ACN_RCA3 Kit.
Getting Started While the Remote Control Anywhere! Kit is compatible with most brands of audio/video components, there are a few exceptions. Y ou should perform a temporary hook- up to test for compatibility before you con ceal wi re o r per man ent ly mount any parts.
5 R EMO TE C ONTR OL A NYWHERE ! K IT Step 2 – Connecting the Sensor Cable to the Connection Hub For your convenience, the sensor cable ends have been stripped. Insert each wire into the appropriate hole on the removable connector plug ( Figure 2 ), and snap the locking tab down.
6 R EMO TE C ONTR OL A NYWHERE ! K IT Figur e 3: Remov able C onnect or Plug 1 = Green/White - 12V 2 = Green - DA T A 3 = Orange/White - GROUND 4 = Blue - EMPTY 5 = Blue/White - ST A TUS 6 = Orange - .
7 R EMO TE C ONTR OL A NYWHERE ! K IT Additional Flashers REMOTE CONTROL ANYWHERE! CONNECTION HUB 3-30V AC/DC STA TUS IN F igure 5: Connection P orts Step 3 – Connecting the 12VDC In-Line Power Supply and MicroFlashers Plug the MicroFlashers into any of the sockets labeled FLASHER OUTPUTS on the connection hub ( Figur e 5 ).
8 R EMO TE C ONTR OL A NYWHERE ! K IT Step 4 – Mounting a MicroFlasher to A/V Components Make sure all of your remote controls have batteries and that they are able to operate the A/V components. Locate a place for the remote control that is within arm’ s length of the A/V components, yet cannot directly control them.
9 R EMO TE C ONTR OL A NYWHERE ! K IT Repeat this procedure for each A/V component you wish to control. When the A/V component responds repeatedly , peel off the protective backing on the MicroFlasher and place the MicroFlasher in that location.
10 R EMO TE C ONTR OL A NYWHERE ! K IT 3-30V AC/DC STA TUS IN Figur e 8: Removing C ables F igure 9A & B A: W all mounting B: If y ou desir e to shelf mount the connection hub , stick the included.
11 R EMO TE C ONTR OL A NYWHERE ! K IT Step 6 – Running the Sensor Cable Conceal the sensor cable between the sensor and the connection hub. For specific information refer to “Running Sensor Cable in New Construction”, located on page 16 , or “Concealing Sensor Cable in Existing W alls”, located on page 18 .
12 R EMO TE C ONTR OL A NYWHERE ! K IT Step 7 – Reconnecting the Connection Hub Reconnect the sensor plug, flashers and power supply as outlined in steps 2, 3 and 4 ( F igure 10 ). That’ s it! Now you are ready to control your audio/video equipment from the room you chose.
13 R EMO TE C ONTR OL A NYWHERE ! K IT Normal Operation T o control your audio/video components, simply aim your remote control at the table-top sensor . If you are within range (and your remote control’ s batteries are fresh), the LED on the sensor will flash a bright blue color each time you press a button on the remote ( Figure 11 ).
REMOTE CONTROL ANYWHERE! KIT CONNECTION HUB Switched outlet on the back of r eceiver or preamp. 3-30V AC/DC STA TUS IN 14 R EMO TE C ONTR OL A NYWHERE ! K IT Optional Accessories Status Feedback W all Adapter The sensor features a status feedback LED that glows green whenever your system is on.
15 R EMO TE C ONTR OL A NYWHERE ! K IT Additional Sensors The Remote Control Anywhere! Kit includes one surface mount sensor . The included MSU250 main system unit will accommodate a second IR sensor . Niles makes a variety of sensors for virtually any application.
16 R EMO TE C ONTR OL A NYWHERE ! K IT Running Sensor Cable in New Construction Scheduling and Preparation Plan to schedule the sensor wiring after the electrical wiring is finished. That way you can avoid cable routes which could potentially induce interference over the sensor cable.
17 R EMO TE C ONTR OL A NYWHERE ! K IT Safety First! W ear gloves, safety goggles and head protection when drilling. Avoid nails, they ruin bits and they can cause injury .
R EMO TE C ONTR OL A NYWHERE ! K IT Pulling the Cable Whenever you run the cable farther than 4-1/2 feet from a hole in a stud or joist (open attic space, going up walls, etc.), fasten the cable to the joists or studs using cable clamps or appropriately sized cable staples.
Exterior walls are different. They must insulate the house from the heat and cold outside, so they are stuffed with insulation. The national building code requires that the hollow wall space in exterior walls be broken by a horizontal stud placed between the vertical studs.
When you don’t have access above or below the wall, try to estimate the existing cable and pipe locations from the positions of electrical outlets and plumbing fixtures on both sides of the wall. Also, take a look at the outside of your house, sometimes a conduit, vent or drain pipe will be visible and will offer useful information.
21 R EMO TE C ONTR OL A NYWHERE ! K IT When you are dealing with the unknown because of the struc- ture of your home, or with diffi- cult materials to patch the wall, such as plaster , lath and plaster , faux finishes, wallpaper etc., be patient. A careful study of the potential problems before you start the job will pay off later .
22 R EMO TE C ONTR OL A NYWHERE ! K IT Specifications MSU250 IR System Compatible with virtually all brands of remotes using carrier frequencies between 26 and 1 05kHz. W iring Requirements Individual home-runs of category 5 cable from each sensor/keypad.
Niles Audio Corpora tion www .nilesaudio.com 1 23 3 1 S.W . 1 30 Street Miami, Florida, 33 1 86 T el: (305) 238-4373 Fax: (305) 238- 0 1 85 © 2004 Niles Audio Corporation. All rights reserved. Niles, the Niles logo, IntelliPad and Blending High Fidelity and Architecture are registered trademarks of Niles Audio Corporation.
R em o t e C o nt r o l A n yw h e r e! ™ Kit B LENDING H IGH F IDELITY AND A RCHITECTURE ® INST ALLA TION & OPERA TION GUIDE R e mo t e C ont r ol An y wher e ! ™ Kit DS00408ACN_RCA3 Kit.
Ein wichtiger Punkt beim Kauf des Geräts Niles Audio RCA3 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Niles Audio RCA3 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Niles Audio RCA3 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Niles Audio RCA3 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Niles Audio RCA3 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Niles Audio RCA3 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Niles Audio RCA3 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Niles Audio RCA3. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Niles Audio RCA3 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
