Benutzeranleitung / Produktwartung 7300 Series des Produzenten NETGEAR
Zur Seite of 364
202-10009-01_06 0204 202-10009-01_060204 June 2004 NETGEAR , Inc. 4500 Great America Parkway Santa Clara, CA User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Sof tware.
ii 202-10009-01_06 0204 © 2004 by NETGEAR, Inc., June 2004. FullManual All rights reserve d. T e chnical Support Please register to obtain technical support . Please retain your proof of p urchase and warranty information. T o register your pr oduct, get product support or obtain product information and product documentation, go to http://www .
202-10009-01_06 0204 iii Canadian Dep artment of Commu nications Compliance St atement This Class B Digital apparatus (NETGEAR 7300 Series Layer 3 Managed Switch) meets all the requirements of the Canadian Interfe rence Causing Equipment Regulations.
202-1000 9-01_060204 iv.
Contents v 202-10009-01_06 0204 Content s Chapter 1 About This Guide Audience ............. ................ ................ ................ ................ ................ ................ ......... ... 1-1 Why the Document was Created ..........
202-10009-01_060204 vi Contents Port-S pecif ic Popup Menus ....................... ................ ................ ................ ............... 4-9 Chapter 5 Command Li ne Interf ace Structure CLI Command Format ........... ................ ...
Contents vii 202-10009-01_06 0204 show interface ethernet ............. ................ ................ ................ ................ ............. .. 8-4 show logging ............ ............. ................. ................ ............. .
202-10009-01_060204 viii Contents no serial baudrate ..... ................ ................ ............. ................ ................ .......... 8-22 serial timeout ................ ................ ............. ... ............. .............
Contents ix 202-10009-01_06 0204 snmptrap mode .................. .......... ................ ............. ................ ................ ............. 8-34 no snmptrap mode . ................ ................ ................ ................ ...
202-10009-01_060204 x Contents no port lacpmode all .............. ................ ............. ................ ............. ................ 8-42 port-channel .......... ............. ................ ................ ............. ..............
Contents xi 202-10009-01_06 0204 set gvrp interfacemode all ...................... ................ ................ ................ ................ 8-50 no set gvrp interfacemode all ...... ................ ............. ................. .........
202-10009-01_060204 xii Contents no shutdown all ...... ................ ................ ................ ............. ................ ............. 8-66 snmp trap link-status ................. ................ ............. ................ ......
Contents xiii 202-10009-01_06 0204 no vlan protocol group add protocol ................ ................ ................ ................ 8-76 vlan protocol group remove ....... ............. ................ ............. ................ ..........
202-10009-01_060204 xiv Contents no spanning-tree mst instance .................. ................ ................. ................ ...... 8-88 spanning-tree mst priority ... ............. ................ ............. ................ ............
Contents xv 202-10009-01_06 0204 dot1x port-control All ................. ... ... ... .... ... ... ............. ................ ................ ............. 8-98 no dot1x port-control All ...... ................ ................ ................ .
202-10009-01_060204 xvi Contents clear igmpsnooping ......................... ................ ................ ................. ................ .... 8-1 13 clear pass .............. ............. ................ ................ ............. ....
Contents xvii 202-10009-01_06 0204 no area virtual-link dead-interval . ................ ................. ................ ................ ..... 9-7 area virtual-link hello-interva l ............. ................ ................. ............. ...
202-10009-01_060204 xviii Contents default-information or iginate (RIP) .. ... ............. ... .... ... ... ............. ... .... ... ... ... ............. 9-15 no default-information originate (RIP) . ................... ................ .........
Contents xix 202-10009-01_06 0204 no ip irdp address ..... ................ .......... ... ................ ............. ................ ............. 9-22 ip irdp hold time ...... ... .... ... ... ... .... ............. ... ... ... ... .... ... ...
202-10009-01_060204 xx Contents no ip rip send version ..... ................. ... ......... ............. ................. ............ .......... 9-30 ip route ............... ... ............. ... .... ... ... ... ............. ... .... ... ... ..
Contents xxi 202-10009-01_06 0204 show ip ospf virtual-link ............. ............. ............ ................. ............. ................ ...... 9-47 show ip ospf virtual-link br ief ........ ................ ............. ................
202-10009-01_060204 xxii Contents no ip vrrp timers advertise ........ ................ ................ ............. ................ .......... 9-60 Chapter 10 CLI Commands: Differenti ated Services General Commands ................. ... .... ... .
Contents xxiii 202-10009-01_06 0204 Show Commands ..... ... ... .... ... ... ... .... ............. ... ... ............. ................ ............. .............. 1 0-17 show class-map . ................ ................ ................ ........
202-10009-01_060204 xxiv Contents no ip dhcp ping packets ......... ............. ................ ................ ................ ............. 12-4 ip dhcp pool .. ... ... ... ... .... ... ... ... ............. .... ... ... ... ... .... ... ......
Contents xxv 202-10009-01_06 0204 Category 5 Cable ......... ................ ................. ... ............. ................ ............. ................ ... 15-2 Category 5 Cable S pecific ations ............... ... ............. ............
202-10009-01_060204 xxvi Contents.
About This Guide 1-1 202-10009-01 _060204 Chapter 1 About This Guide Thank you for pu rchasing the NETGEAR ™ 7300 Series L3 Switch. Audience This reference manual assumes that the reader h as basic-to-intermediate computer and Internet skills.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 1-2 About This Guide 202-10009-01_060204 Note: Refer to the release notes for the 7000 Seri es L3 Managed Switch Software application level code.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software About This Guide 1-3 202-10009-01 _060204 Features of the HTML V ersion of this Manual The HTML version of this manu al includes these feature s. Figure Preface -2: HTML version of t his manual 1.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 1-4 About This Guide 202-10009-01_060204 How to Print this Manual T o print this manu al you man choose one of th e following several optio ns, according to your needs. • Printing a “How T o” Sequence of S teps in the HTML V iew .
Switch Management Overview 2-1 202-10009-01 _060204 Chapter 2 Switch Management Overview This chapter gives an overview of switch ma nagement, including the method s you can use to manage your NETGEAR NETGEAR 7300 Series Layer 3 Managed Switch.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 2-2 Switch M anageme nt Overview 202-10009-01_060204 • Simple Network Protocol Managemen t (SNMP) Each management method enables the network ad ministrator to configure, manage, and control the managed switch locally or remo tely using in-band or out-of-b and mechanisms.
Administration Consol e Telnet Interface 3-1 202-10009-01 _060204 Chapter 3 Administration Console T elnet Interface The administration console is an internal, character-oriented, VT -100/ANSI menu-driven user interface for performing management activities.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 3-2 Administration C onsole Te lnet Interf ace 202-10009-01_060204 Examples o f terminal-emu lation programs include: • HyperT.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Administrat ion Consol e Telnet In terface 3-3 202-10009-01 _060204 4. When the following screen appe ars, make sure that the port setting are as follows: Baud Rate: 9600 Data Bits: 8 Parity: None Stop Bits: 1 Flow Control: None Figure 3-4: Connectio n Settings 5.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 3-4 Administration C onsole Te lnet Interf ace 202-10009-01_060204.
Web-Based Manage men t Interface 4-1 202-10009-01 _060204 Chapter 4 W eb-Based Management Interface Y our NETGEAR 7300 Series Layer 3 Managed Switch provides a built-in browser interface that lets you configure and man age it remotely using a standard W eb browser such as Microsoft Internet Explorer 5.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 4-2 We b-Based M anageme nt Interface 202-10009-01_060204 • Device Management Introduction of the basic icons and management o.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Web-Based M anagement Interface 4-3 202-10009-01 _060204 Click the Login link. A user name and password dial og box opens like this one. Figure 4-4: User name/p assword dialog box 4.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 4-4 We b-Based M anageme nt Interface 202-10009-01_060204 W eb-Based Management Utility Features Figure 4-5: System Information .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Web-Based M anagement Interface 4-5 202-10009-01 _060204 Interactive Switch Image Figure 4-6: Interactive switch imag e This dy.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 4-6 We b-Based M anageme nt Interface 202-10009-01_060204 Figure 4-7: Menu navigat ion Main Menus • Managem ent • Switch •.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Web-Based M anagement Interface 4-7 202-10009-01 _060204 • Smart W izard Secondary Menus The Secondary Menus under the Main Menu contain a host of options that yo u can use to configure your switch.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 4-8 We b-Based M anageme nt Interface 202-10009-01_060204 Routing • Routing Commands — see “Routing Comman ds” on page 9.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Web-Based M anagement Interface 4-9 202-10009-01 _060204 Port-S pecific Popup Menus The 7300 Series L3 Switch also provid es several popup menus for each port.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 4-10 Web-Based M anagement Interface 202-10009-01_060204.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Command Line Interface Stru cture 5-1 202-10009-01 _060204 Chapter 5 Command Line Interface S tructure The Command Line Interface (CLI) syn t ax , conventions and terminology are described in this section.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 5-2 Command Line Inter face Structure 202-10009-01_060204 Parameters Parameters are order dependent.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Command Line Interface Stru cture 5-3 202-10009-01 _060204 logical slot/port This parameter denote s a logical slot number and logical port number assigned. This is applicable in the case of a port-channel (LAG).
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 5-4 Command Line Inter face Structure 202-10009-01_060204 Annot ations The CLI allows the user to type single-line annotations at th e command prompt for use when writing test or configuration scripts and for bette r readability .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Quick Start up 6-1 202-10009-01 _060204 Chapter 6 Quick S t art up The CLI Quick S tart up details procedures to quic kly become acquainted with the 7300 Series L3 Switch. Quick St arting the Switch 1.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 6-2 Quick Start up 202-10009-01_060204 System Info and System Setup Quick S t art up Sof twa re V ersion Information Quick S t art up Physical Port Dat a T able 6-1.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Quick Start up 6-3 202-10009-01 _060204 Quick S t art up User Account Mana gement Quick S t art up IP Address T o view the network parameters the operator can access the device by the following three methods.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 6-4 Quick Start up 202-10009-01_060204 • W eb Brow ser Note: The user should do a copy system:running-config nvram:startup-con.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Quick Start up 6-5 202-10009-01 _060204 Quick S t art up Uploading from Sw itch to Out-of-Band PC (Only XMODEM) T able 6-5.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 6-6 Quick Start up 202-10009-01_060204 Quick S t art up Downloading from Out-of-Band PC to Switch (Only XMODEM) Quick S t art up Download ing from TFTP Se rver Before starting a TFTP server down load, the operator must complete the Quick Start up for the IP Address.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Quick Start up 6-7 202-10009-01 _060204 Quick S t art up Factory Default s T able 6-8. Quick S t art up Factor y Default s Command Details clear config Enter yes when the p rompt pops up to clear all the con figurations made to the switch.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 6-8 Quick Start up 202-10009-01_060204.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Mode-based CLI 7-1 202-10009-01 _060204 Chapter 7 Mode-based CLI The CLI groups all the commands in appropriate modes according to the nature of the comma nd. A sample of the CLI command mode s are described below .
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 7-2 Mode-based CLI 202-10009-01_060204 VLAN Mode From the Privileged User Exec mode, enter the vlan database command. Switch (Vlan) # T o exit to the Privileged Exec mode, enter the exit command, or press Ctrl-Z to switch to user exec mode.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Mode-based CLI 7-3 202-10009-01 _060204 Mode-based T opology The CLI tree is built on a mode concept where the commands are availa ble according to the interface. Some of the modes are depict ed in the mode-based CLI Figure 1.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 7-4 Mode-based CLI 202-10009-01_060204 FIGURE 1. Mode-based CLI Access to all commands in the Privileged Exec mo de and below are restricted through a password.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Mode-based CLI 7-5 202-10009-01 _060204 Mode-based Command Hierarchy The CLI is divided into variou s modes. The Commands in one mo de are not available until the operator switches to that particular mode, with the exception of the User Exec mode commands.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 7-6 Mode-based CLI 202-10009-01_060204 the router interface configur ation commands .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Mode-based CLI 7-7 202-10009-01 _060204 $(Config)# ip dhcp pool <pool-name> Command Prompt: (Conf ig- dhcp -p ool)# Flow of Operation This section captures the flow of operation for the CLI: 1.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 7-8 Mode-based CLI 202-10009-01_060204 4. Once the control has reached the callback f unction, the callback fu nction has complete information about the paramete rs entered by the operator .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-1 202-10009-01 _060204 Chapter 8 Switching Commands This chapter provides detailed explanation of the Switching commands. The commands are divided into five fun ctional groups: • Show commands display switch settings, statistics, and ot her information.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-2 Switching Commands 202-10009-01_060204 numbers that are separate d by colons, for example 01:23:45:67:89:AB IP Address The IP address assigned to each interface. slot/port V alid slot number and a valid port number .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-3 202-10009-01 _060204 Burned in MAC Address Universally assigned network address. Sof tware V ersion The release.version.revision numb er of the code currently run- ning on the switch.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-4 Switching Commands 202-10009-01_060204 Packet s Received Withou t Error The total number of packets (including broadcast pack- ets and multicast packets) received by the processor .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-5 202-10009-01 _060204 this equation is the va lue Utilization which is the percent utiliza- tion of the ethernet segment on a scale of 0 to 100 percent.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-6 Switching Commands 202-10009-01_060204 Unicast Packets Received - The number of subnetwork-unicast packets delivere d to a higher-layer protocol. Multicast Packets Received - The total number of good packets received that were directed to a multicast address.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-7 202-10009-01 _060204 To t a l - A count of valid frame s rece ived which were discarded (i.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-8 Switching Commands 202-10009-01_060204 Packets T ransmitted 64 Octets - The total number of packets (including bad packets) received that were 64 octets in length (excluding framing bits b u t including FCS octets).
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-9 202-10009-01 _060204 Broadcast Pack ets T ransmitted - The total number of packets that higher- level protocols requ ested be transmitted to the Broad- cast address, including those that were discarded or not sent.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-10 Switching Comm a nd s 202-10009-01_060204 BPDU's T ransmitted - The count of BPDU's (Bridge Protocol Data Units) transmitted from the spanning tree layer .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-1 1 202-10009-01 _060204 The display parameters when the ar gum ent is ‘switchport’ is as follows: Octets Received - The total number of octets of data received by the processor (excluding framing b its but including FCS octets).
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-12 Switching Comm a nd s 202-10009-01_060204 protocol. A possible reason for d iscarding a packet coul d be to free up buffer space.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-1 3 202-10009-01 _060204 System Up Tim e The relative time since the last rebo ot of the switch at which this trap occurred. T rap The relevant informa tion of this trap.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-14 Switching Comm a nd s 202-10009-01_060204 GMRP Learned The value o f the co rrespon ding wa s learne d via GMRP and applies to Multicast. Other The value of the corresponding instance does not fall into one of the other categories.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-1 5 202-10009-01 _060204 System Cont act T ext used to identify a contact pe rson for this switch. May be up to 31 alpha-numeric characters. The factory default is blank.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-16 Switching Comm a nd s 202-10009-01_060204 Dot1P Commands classofservice dot1pmapping This command maps an 802.1p pr iority to an internal traffic class for a device when in ‘Global Config’ mode.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-1 7 202-10009-01 _060204 vlan priority This command configures the default 8 02.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-18 Switching Comm a nd s 202-10009-01_060204 St atic Capabi lity This field displays whether or no t the device has static capability enabled. For each port-channel the following information is d isplayed: Name This field displays the name of the port-channel.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-1 9 202-10009-01 _060204 Format no bridge aging-time [ fdbid | all] Mode Global Config Forwarding Dat abase ID Fdbid (Forwarding database ID) indicates which forwarding database's aging timeout is being configured.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-20 Switching Comm a nd s 202-10009-01_060204 Format no network javamode Mode Privileged EXEC network mac-address This command sets locally administered MAC addresses.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-2 1 202-10009-01 _060204 Mode Privileged EXEC network protocol This command specifies the networ k configuration pro tocol to be used. If you mod ify this value change is effective immediately .
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-22 Switching Comm a nd s 202-10009-01_060204 remotecon timeout This command sets the remote connection session timeout value, in minutes. A session is active as long as the session has been idle for the value set.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-2 3 202-10009-01 _060204 serial timeout This command specifies the maximum connect time (in minutes) without console activity . A value of 0 indicates that a console can be connec ted indefinitely .
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-24 Switching Comm a nd s 202-10009-01_060204 Agetime Displays the address aging timeou t for the associa ted forwarding database in IVL. In an SVL system , this will display the system's address aging timeout value in seconds.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-2 5 202-10009-01 _060204 Network Configuration Protocol Current Indicates which netwo r k pro tocol is being used. The options are bootp | dhcp | none. Java Mode Specifies if the switch should a llow access to the Java applet in the header frame.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-26 Switching Comm a nd s 202-10009-01_060204 38400,57600 , and 1 15200 baud. The factory Default is 960 0 baud. Character Size The number of bits in a character . The number of bits is always 8.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-2 7 202-10009-01 _060204 Format show snmpcommunity Mode Privileged EXEC SNMP Community Name The community string to which th is entry grants access. A valid entry is a case-sensitiv e alphanumeric string of up to 16 charac- ters.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-28 Switching Comm a nd s 202-10009-01_060204 St atus A pull down menu that indicates the receiver's status(enabled or dis.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-2 9 202-10009-01 _060204 snmp-server community This command adds (and na mes) a new SNMP community . A community name is a name associated with the switch and with a set of SNMP managers that manage it with a specified privileged level.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-30 Switching Comm a nd s 202-10009-01_060204 no snmp-server community ip addr This command sets a client IP ad dress for an SNMP community to 0.0.0.0 . The name is the applicable community name.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-3 1 202-10009-01 _060204 Mode Global Config no snmp-server community mode This command deactivates an SNMP community . If the community is disabled, no SNMP requests using this community are accepted.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-32 Switching Comm a nd s 202-10009-01_060204 Mode Global Config snmp-server enable trap s bcast storm This command enables the broad cast storm trap.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-3 3 202-10009-01 _060204 snmp-server enable trap s multiusers This command enables Multiple User traps.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-34 Switching Comm a nd s 202-10009-01_060204 Mode Global Config no snmptrap This command deletes trap receivers for a community .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-3 5 202-10009-01 _060204 telnet This command regulates new telnet sessions. If ses sions are enabled, new telnet sessions can be established until there are no more sessions available.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-36 Switching Comm a nd s 202-10009-01_060204 ip http secure-protocol This command is used to set pr otocol levels (versions). The pr otocol level can be set to TLS1, SSL3 or to both TLS1 and SSL3.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-3 7 202-10009-01 _060204 Default enabled Format ip http server Mode Privileged EXEC no ip http server This command disables access to th e switc h through the W eb interface.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-38 Switching Comm a nd s 202-10009-01_060204 no ip ssh This command is used to disable SSH. Format no ip ssh Mode Privileged EXEC ip ssh protocol This command is used to set or remove protocol levels (or v ersi ons) for SSH.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-3 9 202-10009-01 _060204 Format addport <logical slot/port> Mode Interface Config auto-negotiate This command enables automatic negotiation on a port. The default value is ena ble.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-40 Switching Comm a nd s 202-10009-01_060204 deleteport This command deletes the port from the port-chann el (LAG). The interfa ce is a logical s lot and port number of a configured port-chann el.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-4 1 202-10009-01 _060204 monitor session mode This command configures the mon itor session (port monitoring) mo de to enable. The probe and monitored ports must be configur ed before monitor session (port monitoring) can be enabled.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-42 Switching Comm a nd s 202-10009-01_060204 no port lacpmode all This command disables Link Aggregation Control Pro tocol (LACP) on all ports.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-4 3 202-10009-01 _060204 Default Enabled Format port-channel linktrap { <logical slot /port> | all} Mode Global Config no port-channel linktrap This command disables link trap notifications fo r the port-channel (LAG).
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-44 Switching Comm a nd s 202-10009-01_060204 protocol vlan group This command adds the physical <slot/port> inte rface to the protocol-b ased VLAN identified by <groupid>.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-4 5 202-10009-01 _060204 set garp timer join This command sets the GVRP join time per port and per GARP .
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-46 Switching Comm a nd s 202-10009-01_060204 set garp timer leave This command sets the GVRP leave time per port. Leave time is the time to wait after receiving an unregister request for a VLAN or a multicast grou p before deleting the VLAN entry .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-4 7 202-10009-01 _060204 Mode Global Config set garp timer leaveall This command sets how frequently Leave All P DUs are generated per port. A Lea ve All PDU indicates that all registrations will be unregistered.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-48 Switching Comm a nd s 202-10009-01_060204 no set garp timer leaveall all This command sets how frequently Leave All PDUs are generate d fo r all ports to 1000 centiseconds (10 seconds).
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-4 9 202-10009-01 _060204 no set gmrp interfacemode This command disables GARP Multicast Registratio n Protocol on a selected interface.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-50 Switching Comm a nd s 202-10009-01_060204 no set gvrp adminmode This command disables GVRP . Format no set gvrp adminmode Mode Privileged EXEC set gvrp interfacemode This command enables GVRP (GARP VLAN Regi stration Protocol) for a specific port.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-5 1 202-10009-01 _060204 set igmp This command enables IGMP Snooping on th e system. The default value is disable. Note: The IGMP application su pports the following: • Global configuration or per in terface configuration .
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-52 Switching Comm a nd s 202-10009-01_060204 set igmp groupmembershipinterval This command sets the IGMP Group Membersh ip Interval time on the system.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-5 3 202-10009-01 _060204 set igmp maxresponse This command sets the IGMP Maximum Resp onse time on the system.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-54 Switching Comm a nd s 202-10009-01_060204 Format show garp Mode Privileged EXEC and User EXEC GMRP Admin Mode This displays the administrativ e mode of GARP Multicast Regis- tration Protocol (GMRP) for the system.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-5 5 202-10009-01 _060204 Port, per-GARP participant basis. The Leave All Period T imer is set to a random value in th e range of LeaveAllT ime to 1.5*LeaveAllT ime.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-56 Switching Comm a nd s 202-10009-01_060204 seconds). The factory default is 60 centiseconds (0.6 seconds). The finest granularity of specification is 1 centisecond (0.01 sec- onds).
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-5 7 202-10009-01 _060204 Max Response T ime This displays the amount of time the switch will wait after send- ing a query on an interface because it did not receive a report for a particular group on that interface.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-58 Switching Comm a nd s 202-10009-01_060204 show mac-address-t able igmp snooping This command displays the IGMP Snooping en tries in the Multicast Forwarding Database (MFDB) table.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-5 9 202-10009-01 _060204 Component The componen t that is responsibl e for this entry in the Multicast Forwarding Database. Poss ible values are IGMP Snooping, GMRP , and Static Filtering.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-60 Switching Comm a nd s 202-10009-01_060204 displayed as 8 bytes. In an SVL system, the MAC address will be displayed as 6 bytes. T ype This displays the type of the entry . Static entries ar e those th at are configured by the end u ser .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-6 1 202-10009-01 _060204 show port This command displays port in formation. Format show port { <slot/port> | all } Mode Privileged EXEC slot/port The physical slot and physical port.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-62 Switching Comm a nd s 202-10009-01_060204 Group Name This field displays the group name of an entry in the Protocol- based VLAN table. Group ID This field displays the group identifier of the protocol group.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-6 3 202-10009-01 _060204 Active Port s This field lists the ports that are actively participating in the port- channel (LAG). show storm-con t rol This command displays switch configuration information.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-64 Switching Comm a nd s 202-10009-01_060204 Exclude - This port is never a memb er of this VLAN. This is equivalent to registration forbidden in the IEEE 802.1Q standard. Autodetect - Specifies to allow the po rt to be dynamically regis- tered in this VLAN via GVRP .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-6 5 202-10009-01 _060204 show vlan port This command displays VLAN port information.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-66 Switching Comm a nd s 202-10009-01_060204 Mode Interface Config no shut down This command enables a port. Format no shutdown Mode Interface Config shut down all This command disables all ports.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-6 7 202-10009-01 _060204 Mode Interface Config snmp trap link-st atus all This command enables link stat us traps for all interfaces. Note: This command is valid only when the Link Up/Down Flag is enabled (see “snmp-server enable traps linkmode”).
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-68 Switching Comm a nd s 202-10009-01_060204 sp anning-tree bp dumigrationcheck This command enables BPDU migratio n check on a given interface. The all option enables B PDU migration check on all interfaces.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-6 9 202-10009-01 _060204 Mode Global Config Acceptable values are: 100h 100BASE-T half-duplex 100f 100BASE-T full duplex 10h 10BASE-T half duplex 10f 100BASE-T full duplex storm-control broadcast This command enables broadcast storm recovery mode.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-70 Switching Comm a nd s 202-10009-01_060204 Format no switchconfig storm-control broadc ast Mode Global Config storm-control f lowcontrol This command enables 802.3x fl ow control for the switch.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-7 1 202-10009-01 _060204 no vlan This command deletes an existing VLAN. The ID is a valid VLAN identification number (ID 1 is reserved for the default VLAN).
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-72 Switching Comm a nd s 202-10009-01_060204 no vlan ingressfilter This command disables ingress filtering.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-7 3 202-10009-01 _060204 Format vlan participation { exclude | include | auto} <1-4094> Mode Interface Config Participation options are: include The interface is always a member of this VLAN.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-74 Switching Comm a nd s 202-10009-01_060204 vlan port accept frame all This command sets the frame acceptance mode fo r all interfaces. For VLAN Only mode, untagged frames or priority frames received on this interfa ce are discarded.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-7 5 202-10009-01 _060204 vlan port pvid all This command changes the VLAN ID for all interface. Default 1 Format vlan port pvid all < 1-4094> Mode Global Config no vlan port pvid all This command sets the VLAN ID for all interfaces to 1.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-76 Switching Comm a nd s 202-10009-01_060204 Mode Global Config vlan protocol group add protocol This command adds the <protocol> to the protocol-based VLAN identif ied by <groupid>.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-7 7 202-10009-01 _060204 no vlan pvid This command sets the VLAN ID per interface to 1. Format no vlan pvid < 1-4094> Mode Interface Config vlan t agging This command configures the tag ging behavior for a specific interface in a VLAN to enabled.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-78 Switching Comm a nd s 202-10009-01_060204 Format show spanning-tree [brief] Mode Privileged EXEC and User EXEC Bridge Priority Configured value. Bridge Identifier Time Since T opology Change in seconds T opology Change Coun t Number of times changed.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-7 9 202-10009-01 _060204 show sp anning-tree interface This command displays the settings and parameters for a specific switch po rt within the common and internal spanning tree.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-80 Switching Comm a nd s 202-10009-01_060204 Designated Root Identifier of the Regional Root for this multiple spanning tree instance .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-8 1 202-10009-01 _060204 Port Identifier The port identifier for this port within the CST . Port Priority The priority of the port within the CS T . Port Forwarding St ate The forwarding state of the port within the CST .
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-82 Switching Comm a nd s 202-10009-01_060204 Slot/Port The interface being displayed T ype Currently not used. STP St ate The forwarding state of the port in the specified spanning tree instance Port Role The role of the specified port within the spanning tree.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-8 3 202-10009-01 _060204 Configuration Digest Key Calcu lated valu e.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-84 Switching Comm a nd s 202-10009-01_060204 Default The base MAC add r ess displayed using he xadecimal notation as specified in IEEE 802 standard.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-8 5 202-10009-01 _060204 no sp annin g-tree edgeport This command specifies that this port is not an Edge Port within th e common and internal spanning tree.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-86 Switching Comm a nd s 202-10009-01_060204 no sp annin g-tree forward-time This command sets the Bridge Forward Delay pa rameter for the common and internal spanning tree to the default value, i.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-8 7 202-10009-01 _060204 no sp annin g-tree max-age This command sets the Bridge Max Age parameter for the common and inte rnal spanning tree to the default value, i.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-88 Switching Comm a nd s 202-10009-01_060204 If the ‘cost’ token is specified, this command sets the path cost for this po.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-8 9 202-10009-01 _060204 If 0 (defined as the default CIST ID) is passed as the <mstid>, then this command sets the Bridge Priority parameter to a new value for the common and internal spanning tree.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-90 Switching Comm a nd s 202-10009-01_060204 Mode Global Config sp anning-tree port mode This command sets the Admini strative Switch Port St ate for this port to enabled.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-9 1 202-10009-01 _060204 disconnect This command closes a telnet session. Format disconnect { <sessionID> | all} Mode Privileged EXEC show loginsession This command displays current telnet and serial port connections to the switch.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-92 Switching Comm a nd s 202-10009-01_060204 Access Mode Shows whether the operator is able to change parameters on the switch (Read/W rite) or is only able to view them (Read Only).
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-9 3 202-10009-01 _060204 users p asswd This command changes the password of an existing operator . User password should not be more than eight characters in length.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-94 Switching Comm a nd s 202-10009-01_060204 users snmpv3 authentication This command specifies the authentication protocol to be used for the specified logi n user . The valid authentication protocols are none , md5 or sha .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-9 5 202-10009-01 _060204 Security Commands This section describes commands used for configuring security settings for login users and port users. authentication login This command creates an authentication login list.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-96 Switching Comm a nd s 202-10009-01_060204 Format no authentication login <listname> Mode Global Config clear dot1x st atistics This command resets the 802. 1x statistics for the specif ied port or for all ports.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-9 7 202-10009-01 _060204 dot1x login This command assigns the specifie d authentication login list to the specified user for 802.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-98 Switching Comm a nd s 202-10009-01_060204 Default auto Format dot1x port-control {force-un author ized | force-authorized | auto} Mode Interface Config no dot1x port-control This command sets the authentic ation mode to be used on th e specified port to 'auto'.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-9 9 202-10009-01 _060204 dot1x re-authenticate This command begins the re-aut hentication sequenc e on the specified port. This command is only valid if the control mode for the specified port is 'auto'.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-100 Switching Comm a nd s 202-10009-01_060204 Mode Global Config dot1x timeout This command sets the value, in seconds, of the timer used by th e authenticator state machine on this port.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-101 202-10009-01 _060204 no dot1x timeout This command sets the value, in seconds, of the timer used by th e authenticator state machine on this port to the defau lt values.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-102 Switching Comm a nd s 202-10009-01_060204 radius server host This command is used to configure the RADIUS authentication and accounting server .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-103 202-10009-01 _060204 radius server key This command is used to configure the shared se cret between the RADIUS client and the RADIUS accounting / authentication server .
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-104 Switching Comm a nd s 202-10009-01_060204 Format radius server retransmit <retries> Mode Global Config no radius ser.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-105 202-10009-01 _060204 Mode Enabled or di sabled IP Address The configured IP address of the RADIUS acco.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-106 Switching Comm a nd s 202-10009-01_060204 show authentication This command displays the orde red authentication methods for all authentication login lists.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-107 202-10009-01 _060204 If none of the optional param eters are used, the global do t1x configuration summ ary is displayed. Administrative mode Indicates whether authentication co ntrol on the sw itch is enabled or disabled.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-108 Switching Comm a nd s 202-10009-01_060204 T ransmit Period The timer used by the authenticator state machine on the speci- fied port to determine when to send an EAPOL EAP Request/ Identity frame to the supplicant.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-109 202-10009-01 _060204 Last EAPOL Frame V ersion The protocol version number ca rried in the most recently received EAPOL frame. Last EAPOL Frame Source The source MAC address carried in the most recently received EAPOL frame.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-110 Switching Comm a nd s 202-10009-01_060204 Primary Server IP Address Indicat es the config ured serv er currently in use fo.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-111 202-10009-01 _060204 Access Retransmission The number of RADIUS Access- Request packets retransmitted to this RADIUS authentication server .
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-112 Switching Comm a nd s 202-10009-01_060204 802.1x Port Security This field displays the authentic ation login list assigned to the user for 802.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-113 202-10009-01 _060204 Mode Privileged EXEC clear counters This command clears the stats for a specified <slot/p ort> or for all the ports or for the entire switch based upon th e argument.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-114 Switching Comm a nd s 202-10009-01_060204 clear vlan This command resets VLAN configuration parameters to the factory defaults. Format clear vlan Mode Privileged EXEC copy This command uploads and download s to/from the sw itch.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Switching Commands 8-115 202-10009-01 _060204 copy <url> nvram:ssh key-dsa Mode Privileged EXEC logout This command closes the current telnet connection or resets the current serial connection.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 8-116 Switching Comm a nd s 202-10009-01_060204.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-1 202-10009-01 _060204 Chapter 9 Routing Commands This chapter provides detailed explanation of th e Routing commands.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-2 Routing Commands 202-10009-01_060204 area authentication This command specifies the au thentication type to be used for the specified area id.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-3 202-10009-01 _060204 area nssa default-info-originate This command configures the metr ic value and type fo r the defa ult route advertised into the NSSA.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-4 Routing Commands 202-10009-01_060204 area nssa translator-st ab-intv This command configures the translator stability in terval of the NSSA.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-5 202-10009-01 _060204 no area stub This command deletes a stub ar ea for the specified area ID.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-6 Routing Commands 202-10009-01_060204 area virtual-link authentication This command configures the authen tication type and key for the OS PF virtual interface identified by <areaid> and <neighbor>.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-7 202-10009-01 _060204 no area virtual-link dead-interval This command configures the defau lt dead interval for the OSPF vi rtual interface on the virtual interface identified by <areaid> and <neighbor>.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-8 Routing Commands 202-10009-01_060204 Mode Router OSPF Config no area virtual-link retransmit-interval This command configures the default retransmit in terval for the OSPF virt ual interface on the virtual interface identified by <a reaid> and <nei ghbor>.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-9 202-10009-01 _060204 The format is 6 two- digit hexadecimal number s that are separated by colons, for example 00:06:29:32: 81:40. Format arp <ipaddress> <macaddr> Mode Global Config no arp This command deletes an ARP entr y .
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-10 Routing Commands 202-10009-01_060204 no arp dynamicrenew This command disables ARP comp onent from automatically renewing ARP entries of type dynamic when they age out.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-11 202-10009-01 _060204 Default 4 Format arp retries < 0-10> Mode Global Config no arp retries This command configures the default ARP count of maximum request for retries.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-12 Routing Commands 202-10009-01_060204 no auto-summary This command disables the RI P auto-summarization mode. Format no auto-summary Mode Router RIP Config bootp dhcprelay cidoptmode This command enables the circ uit ID option mode for BootP/DHCP Rela y on the system.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-13 202-10009-01 _060204 bootp dhcprelay maxhopcount This command configure s the maximum allowa ble relay agent hops for BootP/DHCP Relay on the system. The <hops> parameter has a range of 1 to 16.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-14 Routing Commands 202-10009-01_060204 bootp dhcprelay serverip This command configures the server IP Addr ess for BootP/DHCP Relay on the sys tem. The <ipaddr> parameter is an IP addre ss in a 4-digit dotte d decimal format.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-15 202-10009-01 _060204 Mode Router OSPF Config default-information originate (RIP) This command is used to control the advertisement of default routes.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-16 Routing Commands 202-10009-01_060204 Format no default-metric Mode Router RIP Config enable (OSPF) This command resets the default administra tive mode of OSPF in the router (active).
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-17 202-10009-01 _060204 The range of preference is 0 to 255.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-18 Routing Commands 202-10009-01_060204 no distribute-list out This command is used to specif y the access list to filter routes received from the source protocol.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-19 202-10009-01 _060204 Restrictions Routed frames are always Ethernet encapsulated when a fram e is routed to a VLAN. exit-overflow-interval This command configures the exit overflow interval for OSPF .
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-20 Routing Commands 202-10009-01_060204 hostroutesaccept This command enables the RIP hostroutesaccept mode. Default Enabled Format hostroutesaccept Mode Router RIP Config no hostroutesaccept This command disables the RIP hostroutesaccept mode.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-21 202-10009-01 _060204 ip ecmpmode This command enables ECMP mode on the router . Default Disabled Format ip ecmpmode Mode Global Config no ip ecmpmode This command disables ECMP mode on the router .
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-22 Routing Commands 202-10009-01_060204 no ip irdp This command disables Router Discovery on an interface. Format no ip irdp Mode Interface Config ip ird p address This command configures the address to be used to advertise the router for the interface.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-23 202-10009-01 _060204 ip ird p maxadvertinterval This command configures the maximum time, in seconds, allowed between sending router advertisements from the interfa ce.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-24 Routing Commands 202-10009-01_060204 Format ip irdp preference < -2147483648-2147483647> Mode Interface Config no ip .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-25 202-10009-01 _060204 Format no ip ospf Mode Interface Config ip osp f areaid This command sets the OSPF area to which the spec ified router interface belongs.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-26 Routing Commands 202-10009-01_060204 ip osp f cost This command configures the cost on an OSPF inte rface.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-27 202-10009-01 _060204 ip osp f hello-interval This command sets the OSPF hello in terval for the sp ecified interface. The value for <seconds> is a valid positive integer , which represents the length of time in seconds.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-28 Routing Commands 202-10009-01_060204 ip osp f retransmit-interval This command sets the OSPF retransmit Interval for the specified interface.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-29 202-10009-01 _060204 ip rip This command enables RIP on a router interface. Default Disabled Format ip rip Mode Interface Config no ip rip This command disables RIP on a router interface.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-30 Routing Commands 202-10009-01_060204 ip rip receive version This command configures the interface to allow RIP control packets of the specified version(s) to be received.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-31 202-10009-01 _060204 ip route This command configures a static route. The <networka ddr> and <n exthopip> are valid ip addresses. The <subnetmask> is a valid subnet mask.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-32 Routing Commands 202-10009-01_060204 Mode Global Config no ip route dist ance This command sets the default static route pref erence value in the router . Lower route pre ference values are preferred when determining the best route.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-33 202-10009-01 _060204 no redistribute This command configures OSPF pro tocol to redi st ribute routes from the speci fied source protocol/ routers.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-34 Routing Commands 202-10009-01_060204 redistribute (RIP) This command config ures RIP protocol to redistribu te routes from the specifie d so urce protocol/ routers.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-35 202-10009-01 _060204 The current value for this func tio n is displayed under "show ip interface" labeled as "Routing Mode".
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-36 Routing Commands 202-10009-01_060204 St atic Entry Count Current / Max Field listing the static entry count in the ARP table and maximum static entry count in the ARP table. The following are displayed for each ARP entry .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-37 202-10009-01 _060204 show bootp dhcprelay This command displays the BootP/DHCP Relay information. Format show bootpdhcprelay Mode Privileged EXEC and User EXEC Maximum Hop Count Is the maximum allowa ble relay agent hops.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-38 Routing Commands 202-10009-01_060204 IP Address Is an IP address representing the subnet configuration of the router interface. This value wa s configured into the unit. Subnet Mask Is a mask of the network and host portion of the IP address for the router interface.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-39 202-10009-01 _060204 Net dir Bcast Indicates if IP forwards net-directed broadcasts on this interface. Possible values are Enable or Disable. MultiCast Fwd Indicates the multicast forwarding administrative mode on the interface.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-40 Routing Commands 202-10009-01_060204 OSPF Admin Mode The administrat ive mode of OSPF in the router . This is a config- ured valu e. ASBR Mode Reflects wheth er the ASBR mode is en abled or disabled .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-41 202-10009-01 _060204 New LSAs Originated The number of new link-state advertisements that have been orig- inated. LSAs Received The number of link-state advertisement s received determined to be new instantiations.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-42 Routing Commands 202-10009-01_060204 show ip osp f dat abase This command displays the link state database. This command takes no options. The information below will only be displa yed if OSPF is enabled.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-43 202-10009-01 _060204 Router Priority A number representing the OSPF Pr iority for the specified inter- face. This is a configured value. Retransmit Interval A number representing the OSPF Retransmit Interval for the specified interface.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-44 Routing Commands 202-10009-01_060204 OSPF Area ID Represents the OSPF Area Id for the specified interface. This is a configured value. Router Priority A number representing the OSPF Pr iority for the specified inter- face.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-45 202-10009-01 _060204 Neighbor Event s The number of times this neighbor relationship has c hanged state, or an error has occurred. External LSA Count The number of external (LS type 5) link-state advertisements in the link-state database.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-46 Routing Commands 202-10009-01_060204 Exchange start - the first step in creating an adjacency between the two neighb oring routers, the goal is to decide which router i s the master and to de cide upon the initial DD sequence number .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-47 202-10009-01 _060204 Format show ip ospf range < areaid> Mode Privileged EXEC and User EXEC Area ID Is the area id of the requested OSPF area. IP Address Is an IP Address which represents this area range.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-48 Routing Commands 202-10009-01_060204 Hello Interval Is the configured hello interv al for the OSPF virtual interface. Dead Interval Is the configured de ad interval for the OSPF virtual interface.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-49 202-10009-01 _060204 RIP Admin Mode RIP administrative mode of router RIP operation; enable acti- vates and disable de-activates the RIP ability for the switch.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-50 Routing Commands 202-10009-01_060204 show ip route This command causes the entire route table to be displayed.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-51 202-10009-01 _060204 show ip route entry This command displays detailed info rmation about the route to a spec ific network to be displayed. The value for <networkaddr> is a valid IP address.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-52 Routing Commands 202-10009-01_060204 show ip st at s This command displays IP statis tical information. Refer to RFC 1213 for more information about the fields that are displayed.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-53 202-10009-01 _060204 Receive version The RIP version(s) allowed wh en receiving updates from the specified interface. The types are none, RIP-1, RIP-2, Both.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-54 Routing Commands 202-10009-01_060204 Router V ersion Errors Represents the total number of VRRP packe t s received with Unknown or unsup po r ted v ersion number .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-55 202-10009-01 _060204 show ip vrrp interface st at s This command displays th e statistical information about each virt ual router configured on the 7300 Series L3 Switch.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-56 Routing Commands 202-10009-01_060204 split-horizon This command sets the RIP split horizon mode. Default simple Format split-horizon { none | simple | poiso n } Mode Router RIP Config no split-horizon This command sets the default RIP split horizon mode.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-57 202-10009-01 _060204 Format no vlan routing <vlanid> Mode VLAN Database ip vrrp This command sets the virtual router ID on an interface for V irtual router configuration in the router .
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-58 Routing Commands 202-10009-01_060204 Mode Interface Config ip vrrp This command enables the administra tive mode of VRRP in the router .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Routing Commands 9-59 202-10009-01 _060204 ip vrrp ip This command sets the ipaddress value for a virt ual router . The value for <ipaddr> is the IP Address which is to be configured on that interface for VRRP .
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 9-60 Routing Commands 202-10009-01_060204 no ip vrrp priority This command sets the default priority value fo r the virtual router configured on a specified interface.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software CLI Commands: Differentiated Services 10-1 202-10009-01 _060204 Chapter 10 CLI Commands: Differentiated Services This chapter contains the CLI commands used for the QOS Differentiated Services (Dif fServ) package.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-2 CLI Commands: Differentiated Services 202-10009-01_060204 Note that the type of class - all, any , or acl - ha s a bearing on the validity of match criteria specified when defining the class.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software CLI Commands: Differentiated Services 10-3 202-10009-01 _060204 diffserv This command sets the DiffServ operational mo de to active. While disabled, the Dif fServ configuration is retained and can be changed, bu t it is not ac tivated.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-4 CLI Commands: Differentiated Services 202-10009-01_060204 class-map This command defines a new DiffServ class of ty pe match-all, match-any or match-access-group.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software CLI Commands: Differentiated Services 10-5 202-10009-01 _060204 This command may be issued at any time; if the class is currently referenced by one or more policies or by any other class, this deletion attempt shall fail.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-6 CLI Commands: Differentiated Services 202-10009-01_060204 Restrictions The class types of both < classname> and < refclassname> must be identical (i.e., any vs. any , or all vs.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software CLI Commands: Differentiated Services 10-7 202-10009-01 _060204 Default None Format match [not] destination-address mac <mac.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-8 CLI Commands: Differentiated Services 202-10009-01_060204 Format match [not] dstl4port {<portkey> | < 0-65535> .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software CLI Commands: Differentiated Services 10-9 202-10009-01 _060204 Mode Class-Map Config match ip tos This command adds to the spe.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-10 CLI Commands: Differentiated Services 202-10009-01_060204 The optional [ not] parameter has the ef fect of negating this match condition for the class (i.e., match all IP Protocol nu mbers ex cept for the one specified here).
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software CLI Commands: Differentiated Services 10-11 202-10009-01 _060204 T o specify the match condition as a si ngle keyword notation, the value for < portkey> is one of the supported port name ke ywords (listed below).
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-12 CLI Commands: Differentiated Services 202-10009-01_060204 T raffic Conditioning Specify traffic conditioning actions (poli.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software CLI Commands: Differentiated Services 10-13 202-10009-01 _060204 successful attachment of a policy to the interface, or shall cause this command to fail if the policy is already in service on one or more interfaces.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-14 CLI Commands: Differentiated Services 202-10009-01_060204 Note: The CLI mode is changed to Policy-Class-Map Config when this co mmand is successfully executed.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software CLI Commands: Differentiated Services 10-15 202-10009-01 _060204 police-simple This command is used to establish the traf fic polic ing style for the specified class.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-16 CLI Commands: Differentiated Services 202-10009-01_060204 The service commands attach a de fined policy to a directional interface. Only one policy may be assigned at any on e time to an in terface in a particular direction.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software CLI Commands: Differentiated Services 10-17 202-10009-01 _060204 Format no service-policy {in | out} <policy mapname> Mod.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-18 CLI Commands: Differentiated Services 202-10009-01_060204 Match Criteria The Match Criteria fields will only be displayed if they have been configured. They will be displaye d in the order entered by the user .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software CLI Commands: Differentiated Services 10-19 202-10009-01 _060204 show diffserv This command displays the DiffServ General St at.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-20 CLI Commands: Differentiated Services 202-10009-01_060204 Policy Name The name of this poli cy . T ype The policy type, namely whether it is an inb ound or outbound policy definition.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software CLI Commands: Differentiated Services 10-21 202-10009-01 _060204 Exceed Action The current setting for the action ta ken on a packet considered to exceed to the policing parameters.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-22 CLI Commands: Differentiated Services 202-10009-01_060204 Random Drop Maximum Drop Probability This field displays the RED maximum drop probability .This is not displayed if the queue depth management scheme is not RED.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software CLI Commands: Differentiated Services 10-23 202-10009-01 _060204 show diffserv service brief This command displays all interfaces in the system to which a Dif fServ po licy has been attached.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-24 CLI Commands: Differentiated Services 202-10009-01_060204 Interface Discarded Oc tet s/Packet s A cumulative count of the octets/packets discarded by this service interface in the specified direction for any reason due to Dif fServ treatment.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software CLI Commands: Differentiated Services 10-25 202-10009-01 _060204 Note: None of the counters listed here are guarante ed to be supported on all platforms. Only supported counters are shown in the display output.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 10-26 CLI Commands: Differentiated Services 202-10009-01_060204.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software CLI Commands: ACL 11-1 202-10009-01 _060204 Chapter 11 CLI Commands: ACL Show Commands show ip access-list s This command displays an Access Control List (ACL ) and all of the rules that are defined for the ACL.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 11-2 CL I Commands: ACL 202-10009-01_060204 Configuration Commands access-list This command creates an Acc ess Control List (ACL) that is identified by the parameter < accesslistnumber>.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software CLI Commands: ACL 11-3 202-10009-01 _060204 Mode Global Config ip access-group This command attach a specified ac cess-control list to an interface.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 11-4 CL I Commands: ACL 202-10009-01_060204.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software DHCP Server Commands 12-1 202-10009-01 _060204 Chapter 12 DHCP Server Commands DHCP Server Configuration Commands These commands configure the DHCP Se rver parame ters and address pools.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 12-2 DHCP Server Commands 202-10009-01_060204 Format no client-name Mode DHCP Pool Config Mode default-router This command specifies the defa ult router list for a DHCP client.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software DHCP Server Commands 12-3 202-10009-01 _060204 hardware-address This command specifies the hardwa re address of a DHCP client. Hardware-address is the MAC addres s of the hardware platform of the client consisting of 6 bytes in dotted hexadecimal format.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 12-4 DHCP Server Commands 202-10009-01_060204 ip dhcp excluded-address This command specifies the IP addresses that a DHCP server should not assign to DHCP clients. Low-address and high-address are valid IP addresses; each made up of four decimal bytes ranging from 0 to 255.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software DHCP Server Commands 12-5 202-10009-01 _060204 ip dhcp pool This command configures a DHCP address pool name on a DHCP server and enters DHCP pool configuration mode.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 12-6 DHCP Server Commands 202-10009-01_060204 network This command is used to config ure the subnet number and mask for a DHCP address pool on the server . Network-number is a valid IP address, ma de up of four decimal bytes ranging from 0 to 255.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software DHCP Server Commands 12-7 202-10009-01 _060204 show ip dhcp binding This command displays address bindings for the specific IP address on the DHCP server . If no IP address is specified, the bindings corresp onding to all the addresses are displa yed.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 12-8 DHCP Server Commands 202-10009-01_060204 Following additional field is displayed fo r Dynamic pool type Network The network number and the mask for the DHCP address pool.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software DHCP Server Commands 12-9 202-10009-01 _060204 DHCPOFFER The number of DHCPOFFER messages that were sent by the server . DHCP ACK The number of DHCPP ACK messages tha t were sent by the server .
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 12-10 DHCP Server Commands 202-10009-01_060204.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software FSM7326P Power Over Ethernet Comm ands 13-1 202-10009-01 _060204 Chapter 13 FSM7326P Power Over Ethernet Commands This chapter provides information on the Power Over Ethernet Commands available in the FSM7326P Switch software.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 13-2 FSM7326P Power Over Ethernet Comman ds 202-10009-01_060204 Attached to the PSE is the UPS. A UPS is connecte d to ea ch device that re quires alternative power . W ith Power over Ethernet, this fu nction is centralized in a UPS co nnected to the PSE.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software FSM7326P Power Over Ethernet Comm ands 13-3 202-10009-01 _060204 poe priority This command sets the priority level for the delive ry of power to an attached device.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 13-4 FSM7326P Power Over Ethernet Comman ds 202-10009-01_060204 The following fields are displayed for each port. If a port does not have lin k, or is not enabled for PoE, the following fields display a value of "N/A".
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software FSM7326P Power Over Ethernet Comm ands 13-5 202-10009-01 _060204 show poe This command displays the tota l power available and the total power consumed in the system.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software 13-6 FSM7326P Power Over Ethernet Comman ds 202-10009-01_060204.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-1 202-10009-01 _060204 Appendix A IS CLI Mapping This chapter illustrates the mapp ing between CLI commands and th e previous 7300 Series L3 Switch commands. The Package column indicates th e 7300 Series L3 Switch package in whic h the command is located.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-2 IS CLI Mapping 202-10009-01_060204 QOS config acl rule action <acli d> <rulenum> <permit/deny> QOS config .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-3 202-10009-01 _060204 QOS config acl rule match srcl4port range <aclid> <rulenum> <startport&g.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-4 IS CLI Mapping 202-10009-01_060204 QOS config diffserv policy delete <policyname> Global Config no policy-map <poli.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-5 202-10009-01 _060204 QOS config diffserv policy police style simple <policyname> <classna me> &l.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-6 IS CLI Mapping 202-10009-01_060204 QOS config diffserv policy police action conform markprec <policyname> <classnam.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-7 202-10009-01 _060204 QOS show diffserv service stat s summary [in/out] Pri vileged EXEC show service-policy .
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-8 IS CLI Mapping 202-10009-01_060204 Class-Ma p Config match not cos <0-7> QOS config diffserv class match dstip <cla.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-9 202-10009-01 _060204 QOS config diffserv class match iptos <classname> <tosbits> <tosmask>.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-10 IS CLI Mapping 202-10009-01_060204 Class-Ma p Config match not sou rce-address mac <address> <macmask> QOS conf.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-11 202-10009-01 _060204 Routing show ro uter ospf interface summary Privileged EXEC and User EXEC show ip ospf.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-12 IS CLI Mapping 202-10009-01_060204 Routing show router rip interface summar y Privileged EXEC and User EXEC show ip rip int.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-13 202-10009-01 _060204 Routing show router vrrp interface stats <slot/port> <V rID> Privileged EX.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-14 IS CLI Mapping 202-10009-01_060204 Routing config arp resptime <seconds> Global Config arp resptime <1-10> Glob.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-15 202-10009-01 _060204 Routing config ip vlan routi ng create <vla n> VLAN database vlan routing <vl.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-16 IS CLI Mapping 202-10009-01_060204 Routing config router ospf interface interval dead <slot/port> <1-21 47483647&g.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-17 202-10009-01 _060204 Routing config ro uter ospf area range create <areaid> <ipaddr> <subnet.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-18 IS CLI Mapping 202-10009-01_060204 Interface Config no ip rip a uthentication Routing config ro uter ri p interface default.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-19 202-10009-01 _060204 Routing config router ospf virtif interval dead <areaid> <neig hbor> <1.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-20 IS CLI Mapping 202-10009-01_060204 Routing config router route staticpreference <local/static> <0-255> Global C.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-21 202-10009-01 _060204 Routing config ro uter vrrp in terface authdetails <slot/port> <vrID> <.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-22 IS CLI Mapping 202-10009-01_060204 Global Config no bootpdhcprelay disable Routing config router bootpd hcprelay maxhopcoun.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-23 202-10009-01 _060204 Routing config router rip splithorizon <none/ simple/poison> Router RIP Config s.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-24 IS CLI Mapping 202-10009-01_060204 Privileged EXEC no ip http server Switching config network javamod e <enable | disabl.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-25 202-10009-01 _060204 Global Config no snmp-server community ipmask <name> Switching config snmpcommun.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-26 IS CLI Mapping 202-10009-01_060204 Global Config no snmp-server enable traps multiusers Switching config trapflags stpmode .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-27 202-10009-01 _060204 Switching show spanningtree cst detailed Privileged EXEC and User EXEC show spanning-t.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-28 IS CLI Mapping 202-10009-01_060204 Global Config no spanning-tree forceversion Switching config spanningtree configuration .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-29 202-10009-01 _060204 Switching config spanningtree bridge forwarddelay <4-30> Global Config spanning-.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-30 IS CLI Mapping 202-10009-01_060204 Switching config spanningtree mst port pathcost <mstid> <slot/port> <1-20.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-31 202-10009-01 _060204 Switching show traplog Privileged EXEC show logging Switching config sysname <name&.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-32 IS CLI Mapping 202-10009-01_060204 Switching transfer download mode < xmodem | tf tp> Switching transfer download ser.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-33 202-10009-01 _060204 Switching logout Privileged EXEC logout Switching show users info Privileged EXEC show.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-34 IS CLI Mapping 202-10009-01_060204 Switching show lag <logical slot/port | all> Privileged EXEC show port-channel {&l.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-35 202-10009-01 _060204 Switching show mfdb table [macaddr/all] Privileged EXEC show mac-address-table multica.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-36 IS CLI Mapping 202-10009-01_060204 Interface Config no snmp trap link- status Global Config snmp trap link- status all Glob.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-37 202-10009-01 _060204 Switching config lag deleteport <l ogical slot/ port> <slot/port | all> In.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-38 IS CLI Mapping 202-10009-01_060204 Global Config vlan participation all {exclude | include | auto} <1-4094> Switching.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-39 202-10009-01 _060204 Switching config protocol create <groupname> Global Config vlan protocol group &.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-40 IS CLI Mapping 202-10009-01_060204 Global Config no set gmrp interfacemode all Switching config garp gvrp adminmode <ena.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-41 202-10009-01 _060204 Switching config garp leaveallti me r <slot/port/ all> <200-6 00> Interfac.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-42 IS CLI Mapping 202-10009-01_060204 Global Config set igmp interfacemode all Switching config mirror ing de lete Glo bal Con.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-43 202-10009-01 _060204 Security config ra diu s maxretransmit <1 - 15> Global Config radius server retr.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-44 IS CLI Mapping 202-10009-01_060204 Security show radius summary Privileged EXEC show radius [servers] Security show radius .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software IS CLI Mapping A-45 202-10009-01 _060204 Interface Config dot1x port-control {force-unauthorized | force-authorized | auto} Int.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software A-46 IS CLI Mapping 202-10009-01_060204 Security config dot1x port users ad d <user> <slot/port/all> Global Config d.
Cabling Guidelines B-1 202-10009-01 _060204 Appendix B Cabling Guidelines This appendix provides specifications for cab les used with a NETGEAR NETGEAR 7300 Series Layer 3 Managed Switch. Fast Ethernet Cable Guidelines Fast Ethernet uses UTP cable, as specified in the IEEE 802.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software B-2 Cabling Guidelines 202-10009-01_060204 Category 5 Cable Category 5 distributed cable that me ets ANSI/EIA/ TIA-568-A building wiring stan dards can be a maximum of 328 feet (ft.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Cabling Guidelines B-3 202-10009-01 _060204 T able 13-3. Electrical Requir ement s of Category 5 Cable T wisted Pair Cables For two devices to communicate, th e transmitter of each device must be connected to the receiver of the other device.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software B-4 Cabling Guidelines 202-10009-01_060204 Figure 13-2 illustrates crossover twisted pair cable. Figure 13-2: Crossover T wisted-Pair Cable Patch Panels and Cables If you are using patch panels, make sure th at they meet the 100BASE- TX requirements.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Cabling Guidelines B-5 202-10009-01 _060204 Note: Flat “silver satin” telephone cable ma y have the same RJ-45 plug. However , using telephone cable results in excessive collisions, cau sing the attached port to be partitioned or disconnected from the ne twork.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software B-6 Cabling Guidelines 202-10009-01_060204 Unlike 10BASE-T and 100BASE-TX, which use only two of the four pairs of wires wit hin the Category 5, 1000BASE-T u ses all four pairs of th e twisted pair .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Cabling Guidelines B-7 202-10009-01 _060204 Figure 13-4 shows the RJ-45 plug and RJ-45 connector . Figure 13-4: RJ-45 Plug and RJ-4 5 Connector with Built-in LEDs Ta b l e 1 3 - 1 lists the pin assignments for th e 10/100 Mbps RJ-45 plug an d the RJ-45 connector .
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software B-8 Cabling Guidelines 202-10009-01_060204 T able 13-2. 100/1000 Mbp s RJ-45 Plug and RJ-45 Connector Pin Assig nment s Conclusi.
Glossary C-1 202-10009-01 _060204 Appendix C Glossary Use the list below to find definitions for technical terms used in this manual. Numeric 802.1D The IEEE designator for Spanning Tree Protocol (STP). STP , a link managem ent proto col, is part of the 802.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software C-2 Glossary 202-10009-01_060204 100BASE-TX The IEEE specification for 100 Mbps Fast Ethernet over Category 5 twisted-pair cabl e . 1000BASE-SX The IEEE specification for 1000 Mbps Gigabit Ethernet over fib er-optic cable.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Glossary C-3 202-10009-01 _060204 ASBR See “Autonomous System Boundary Router” o n page 3. Autonomous System Boundary Router ABR located between an OSPF autonom ou s system an d a n on-OSPF network.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software C-4 Glossary 202-10009-01_060204 Boot strap Protocol An Internet protocol that enables a diskless workstation to discover its own IP address, the IP address of a BootP server on the network, and a file to be loaded int o memory to boot the machine.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Glossary C-5 202-10009-01 _060204 Class of Service A term to describe treating different types of traffic wi th different levels of service priority .
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software C-6 Glossary 202-10009-01_060204 to travel services, in which a person can choose among different modes of travel - train, bus, airplane - degree of comfort, the number of stops on the route, stan dby statu s, the time of day or period of year for the trip, and so forth.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Glossary C-7 202-10009-01 _060204 identity , which the AP gets from the user and th en send s back to the server to complete the authentication. EAP is defined by RFC 2284. Endsta tion A computer , printer , or server that is connected to a network.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software C-8 Glossary 202-10009-01_060204 Full-duple x A system that allows packets to be transmitted and received at the same time and, in effect, doubles the potential throughput of a link.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Glossary C-9 202-10009-01 _060204 GMRP See “GARP Multicast Registrati on Prot ocol” on page 8. GVD GARP VLAN Database. GVRP See “GARP VLAN Registration Protocol” on page 8.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software C-10 Glossary 202-10009-01_060204 Internet Control Mess age Protocol ICMP is an extension to the Internet Protocol (IP) that supp orts pack ets containing error , control, and informational messages.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Glossary C-11 202-10009-01 _060204 L LAN See “Local Area Network” on page 1 1. LDAP See “Lightweight Directory Access Protocol” on page 11. Lightweight Directory Access Protocol A set of protocols for accessing inform ation directories.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software C-12 Glossary 202-10009-01_060204 M MAC (1) Medium Access Control. In LANs, the sublayer of the data link control layer that supp orts medium-dependent functions and us es the services of the physical layer to provide services to the logical link control (LLC) sublayer .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Glossary C-13 202-10009-01 _060204 MPLS See “Multi-Protocol Label Switching ” on page 13.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software C-14 Glossary 202-10009-01_060204 Routers (LSRs) place outgoing labels on the packets. W ith these LSPs, network operators can divert and route traffic based on data-stream type and Internet-a ccess customer .
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Glossary C-15 202-10009-01 _060204 protocol. This protocol's algorithm determines the shortest path from its router to all th e ot her routers in the network. This protocol is rapidly replacing RIP on the Intern et.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software C-16 Glossary 202-10009-01_060204 if necessary . Port mirroring can be managed locally or remotely . An administrato r configures port mirroring by assigning a port from which to copy all packets and another port where those packets will be sent.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Glossary C-17 202-10009-01 _060204 R RADIUS Short for Remote Auth ent ication Dial-In User Service, RADIUS is an authentication s ystem. Using RADIUS, you must enter your user name and password before gaining access to a network.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software C-18 Glossary 202-10009-01_060204 RSVP See “Resource Reservation Setup Protocol” on pa ge 1 7.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Glossary C-19 202-10009-01 _060204 SNMP See “Simple Network Management Protocol” on page 18. Sp anning T ree A technique that detect s loops in a netw ork and logically b locks the redundant p aths, ensuring that only on e route exists between any two LANs.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software C-20 Glossary 202-10009-01_060204 TFTP See “TLS” on page 20. TLS Short for Transport Layer Security , TLS is a protocol that guarantees privacy an d data integri ty betw een client/server applications co mmunicating over the Internet.
User Manual for the NETGEAR 7300 Series Laye r 3 Managed Switch Software Glossary C-21 202-10009-01 _060204 an 802.1Q-co mpliant switch or rout er . Devices recognizing 802.1Q-tagged frames maintain appropri ate tables to track VLANs. The firs t three bits of the 802.
User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software C-22 Glossary 202-10009-01_060204 WINS WINS. W indows Internet Naming Servi ce is a server process for reso lving W indows-based computer names to IP addresses. X XModem One of the most popular file transfer protocols (FTPs).
Ein wichtiger Punkt beim Kauf des Geräts NETGEAR 7300 Series (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie NETGEAR 7300 Series noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für NETGEAR 7300 Series - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von NETGEAR 7300 Series reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über NETGEAR 7300 Series erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon NETGEAR 7300 Series besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von NETGEAR 7300 Series verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit NETGEAR 7300 Series. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei NETGEAR 7300 Series gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
