Benutzeranleitung / Produktwartung NLT-32W des Produzenten NEC
Zur Seite of 32
32 inc h 32 " TFT LCD TV NL T -32W.
Wa r nings W ARNING : To prevent fire or shock hazard, do not expose the set to rain or moisture. Do not rub or strike the Active Matrix LCD with anything hard as this may scratch, mar, or damage the Active Matrix LCD permanently. The appliance is not intended for use by young children or infirm persons without supervision.
22 3 Wa r nings Service Never remove the back cover of the TV, this can expose you to high voltage and other hazards. If the TV does not operate properly, unplug it and call your nearest NEC Service Centre. Connect the antenna cable to the connection marked Ant.
Contents Warnings 2~3 Contents 4 Supplied Accessories 5 Controls 6~8 Controller of panel 6 Remote controller 7~8 Basic Operation 9 Turning the TV On and Off 9 Programme selection 9 Volume adjustment 9 Q.
22 5 Supplied Accessor ies L Make Sure the following accessories are provided with Product. 2. Remote controller 4. Owner’s manual 5. PC IN cable 6. PC Audio IN cable 3.
6 Controls 1. PC DIGITAL IN (DVI-I) 2. H/P (Headphone out) Connect a headphone to this socket. 3. PC AUDIO IN Connect the audio cable from the PC to the PC AUDIO IN of the set. 4. PC ANALOG IN (D-SUB) 5. COMPONENT IN 6. DTV IN 7. AV-IN 8. AV-OUT 9. S-VIDEO IN Connect the output of the S -VIDEO on the VCR to the S-VIDEO input.
22 7 Controls All the functions can be controlled with the remote controller. Some functions can also be adjusted with the buttons on the side panel of the set. Remote controller Before you use the remote controller, please install the batteries. 1. POWER Turns the TV on from standby or off to standby mode.
22 8 Controls →→ Battery installation u Inserting batteries 1. Remove the battery cover by pulling it upward in the direction shown by the arrow. 2. Insert the batteries with correct polarity ( "+" to "+", and "-" to "-" ).
22 9 Tu r ning the TV On and Off Standby Setup: The AC power cord must be set up and connected to have the TV in standby mode ready to be turned on. Press the ON/OFF button on the side panel of the TV to go into standby mode. 1. If the TV is in standby mode, press the POWER button on the remote controller or the TV itself to turn the TV on.
22 10 On Screen Menus and Displays 1. Press the MENU button to display main menu. 2. Press the PR x y button to select menus-Picture, Sound, Special, Setup. 3. Adjust each menu with the VOL Ïq button. 4. Press the MENU button to return to preceding menu.
22 11 Setting up TV Programme Once you have preset the programmes, you will be able to use the PR xy or NUMBER buttons to scan the programmes you programmed. Programmes can be tuned using automatic or manual modes. Auto Programme All programmes that can be received are stored by this method.
12 Setting up TV Programme Manual Programme Manual Programme lets you manually tune and arrange the programmes in whatever order you desire. Also you can assign a programme name with 5 characters to each programme number. 1. Press the MENU button. 2. Select the Setup menu, then press VOL Ïq .
22 13 Setting up TV Programme Deleting a programme 1. Select a programme to be deleted with the PR xy or VOL Ïq button. 2. Press the RED button once. The selected programme is deleted, all the following programme is shifted up one position. Naming a programme 1.
Note. In PC mode, PSM function isn’t available. 14 Picture Control You can adjust picture Contrast , Brightness , Colour , Sharpness and Tint (only in NTSC mode) to the levels you prefer. Auto Picture Contr ol *The Picture options - Dynamic, Standard, Mild and Game are programmed for good picture reproduction at the factory and cannot be changed.
22 15 Sound Control You can select your preferred sound setting; Flat , Music , Movie or Speech . You can also adjust the sound frequency of equalizer, balance. If you switch AVL to on, the set automatically keeps on an equal volume level even if you change programmes.
Sound Control 16 Auto Sound Control * The sound Flat , Music , Movie and Speech are programmed for good sound reproduction at the factory and cannot be changed. SSM (Sound Status Memory) 1. Press the SSM button. 2. Press the SSM button repeatedly to select.
22 17 Other functions You can control other functions; Clock , Blue Back , Auto Sleep , Childlock , Radio and ARC menu. Clock Setting the clock is necessary in order to use the various timer features of the TV. You can set automatic TV On or Off time.
Other functions Auto Sleep If you select Auto Sleep On the set will automatically switch itself to standby mode approximately ten minutes after a TV Channel stops broadcasting. 1. Press the MENU button. 2. Select the Special menu, then press VOL Ïq .
19 Radio Control This function is possible only when the set is in Radio mode.(Radio mode is displayed when the Setting for special menu is radio On.) 1. Use TV/AV button on remote controller to select Radio mode . 2. Press the MENU button to set Radio Setup menu.
20 Other functions Calling the programme list You can check the programmes stored in the memory by displaying the programme LIST. Displaying programme list 1. Press the LIST button to display the Programme list menu. The programme list appears on the screen.
22 21 TELETEXT TEXT On/Off Press the TEXT/MIX button to switch to TELETEXT. The initial page or last selected page appears on the screen. The first page number indicates your selection, while the second shows the current page displayed. 1. Press TEXT/MIX button once, displays the Teletext pages.
TELETEXT Special TELETEXT functions Changes Teletext mode Only Teletext mode, text mode superimposed on the TV picture, TV mode Selects double height text. Press this button to enlarge the top half of the page. Press this button again to enlarge the bottom half of the page.
23 Antenna connection 1. Connect RF out on the VCR to the Antenna input on the rear of the TV. 2. Connect the antenna cable to the antenna in jack on the VCR. 3. Use the TV/AV button to select TV mode. 4. Press the PLAY button on the VCR. COMPONENT INPUT 1.
22 Exter nal Equipment Connection A/V INPUT 1. Connect the A/V out jacks on of the VCR to A/V-In jacks on the TV. 2. Press the TV/AV button to select VIDEO mode. 3. Press the PLAY button on the VCR. The VCR playback picture appears on the screen. Note : If you have a mono VCR, connect the audio cable from the VCR to the L(MONO) socket of the set.
22 25 Connecting the PC as a monitor This function is possible only when the set is in PC mode. Use the TV/AV button on remote controller. Picture adjustment You can adjust picture Contrast , Brightness , Temperature , Clock , Phase and ARC as you prefer.
Connecting the PC as a monitor Sound adjustment 1. Press the MENU button. 2. Select the Sound menu, then press VOL Ïq . 3. Press the PR xy button to select the desired sound item; Equalizer, Balance, AVL, Surround or Sound Mode . 4. Press the VOL Ïq button to make desired adjustment.
27 Connecting the PC as a monitor Auto This function is for the automatic adjustment of the screen position, clock and clock phase. The displayed image will disappear for a few seconds while the Auto-configuration is in process. Note: Some signal from some graphics boards may not function properly.
Connecting the PC as a monitor DVI (Digital Visual Interface) INPUT 1. Connect the DVI of PC to the DVI input on the TV. 2. Select PC-Digital mode by pressing the TV/AV button repeatedly. (When DVI source is connected, TV/AV mode converts PC to DVI mode.
22 29 Product Specifications Model NLT-32W Main body Horizontal size 960(960) mm Thickness 109(222) mm (With stand) Height 513(565.5) mm Weight 17.6(19.
T roubleshooting No picture on screen and no sound from speakers No picture/No picture from AV terminal Picture is displayed, but no sound from the speakers. Picture is too light There are stripes on the screen or colors fade. Picture is too dark. Remote control does not work.
22 31 NEC Australia Pty. Ltd. ABN 86 001 217 527 Home Electronics Group NEC Service Centr es New South Wales Sydney 184 Milperra Rd, Revesby 2212 131-632 Newcastle 120 Parry Street, Newcastle West 230.
500-011H050729.
Ein wichtiger Punkt beim Kauf des Geräts NEC NLT-32W (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie NEC NLT-32W noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für NEC NLT-32W - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von NEC NLT-32W reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über NEC NLT-32W erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon NEC NLT-32W besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von NEC NLT-32W verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit NEC NLT-32W. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei NEC NLT-32W gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
