Benutzeranleitung / Produktwartung MD213MC des Produzenten NEC
Zur Seite of 32
MD2 1 2 M C MD2 13MC MD2 13MG INST ALL A TION & MAINTENANCE GUIDE.
Index W arning, Caution ............................................................................................................... ......... English-1 Registration Information ......................................................................
English-1 English W ARNING CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM W ALL SOCKET . TO FULL Y DISENGAGE THE POWER T O THE UNIT , PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET . DO NOT REMOVE COVER (OR BACK).
English-2 Registration Information Declaration of the Manufacturer Means of Conformity Device Classification: Class I, non-measuring function Applicable Rules: Annex IX, Rules 1.4 (Section 1) and 1.1 (Section 3) Product Name: MD212MC/MD213MC 21.3" Diagnostic Imaging Color LCD Monitor MD213MG 21.
English-3 English Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOR MONIT OR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks.
English-4 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONIT OR CAN REDUCE EYE, SHOULDER AND NECK F A TIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level.
English-5 English Contents Y our new NEC monitor box* should contain the following: • MD212MC/MD213MC/MD213MG monitor with tilt/swivel/pivot/height adjust stand • Power Cord •V ideo Signal Cable.
English-6 Figure C.1 Quick Start To attach the LCD monitor to your system, follow these instructions: NOTE: Make sure to read “Recommended Use” before installation.
English-7 English Figure C.3 Figure D.1 Figure D.2 Figure C.4 8. Hold all cables firmly and place the cable cover onto the stand ( Figure D.1 ). T o remove the cable cover , lift the cover off as shown in Figure D.2 . 9. Connect one end of the power cord to the AC inlet on the back of the monitor and the other end to the power outlet.
English-8 T ilt Grasp both sides of the monitor screen with your hands and adjust the tilt as desired ( Figure TS.1 ). Figure TS.1 Swivel Grasp both sides of the monitor screen with your hands and adjust the swivel as desired ( Figure TS.2 ). NOTE: Handle with care when tilting the monitor screen.
English-9 English Mount Flexible arm 1. Change the 4 screws that were removed from the stand removal to attach the flexible arm to the monitor ( Figure F .1 ). Caution: • When mounting, use ONL Y the screws (4 pcs) that were removed from the stand to avoid damage to the monitor or stand.
English-10 Controls The OSD (On-Screen Display) control buttons are located on the back of the monitor: To access OSD menu, press the EXIT button. T o change signal input, press the SELECT button. NOTE: OSD must be closed in order to change signal input.
English-11 English Luminance/Contrast Controls LUMINANCE Adjusts the overall image and background screen luminance. When LUMINANCE is adjusting the numerical values blinks. AUTO CONTRAST (Analog input only) Adjusts the image displayed for non-standard video inputs.
English-12 EXP ANSION Sets the zoom method. FULL: The image is expanded to 1200 x 1600 (in portrait mode) or 1600 x 1200 (in landscape mode) for MD212MC and 1536 x 2048 (in portrait mode) or 2048 x 1536 (in landscape mode) for MD213MC/MD213MG, regardless of the resolution.
English-13 English OFF MODE This function allows the monitor to enter into a power saving mode after a period of inactivity . The OFF MODE has two settings. OFF: Monitor does not go into power save mode when the input signal is lost. ST ANDARD: Monitor enters power save mode automatically when the input signal is lost.
English-14 F ACTOR Y PRESET Selecting Factory Preset allows you to reset all OSD control settings (LUMINANCE, BLACK LEVEL, IMAGE CONTROL, COLOR CONTROL SYSTEM, SHARPNESS, OFF MODE, OSD LEFT/RIGHT , OSD UP/DOWN, OSD TURN OFF) back to the factory settings.
English-15 English T ag1 Luminance Adjusts the overall image and screen background luminance. Press “Left” or “Right” to adjust. When LUMINANCE is adjusting, a numerical value blinks. Auto Contrast Adjusts the image displayed for non-standard video inputs.
English-16 T ag3 Auto Adjust Automatically adjusts the Image Position and V .Size (H.Size) settings and Fine settings. (Analog input only) Press “SELECT” to activate Auto Adjustment. Signal Adjust Determines when the auto adjustment is activated automatically .
English-17 English H.ZOOM The image is expanded from 1 to 3 times in the horizontal (H. EXP ANSION) direction by (Available in Custom 0.01 increments. Expansion mode only) V .ZOOM The image is expanded from 1 to 3 times in the vertical (V . EXP ANSION) direction by (Available in Custom 0.
English-18 T ag7 Sharpness This is a digital capability for keeping a crisp image at all signal timings. It continuously adjusts to maintain as distinct or as soft an image as you prefer and is set independently according to different timings. Press “Left” or “Right” to adjust.
English-19 English OSD Lock Out This control completely locks out access to all OSD control functions. When attempting to activate OSD controls while in the Lock Out mode, a screen will appear indicating the OSD controls are locked out.
English-20 Input Setting Video Band Width: Reduce the visual “noise” level of the input signal. (Analog input only) The video band width settings range from 0-7, with 0 having no correction and 7 having the most noise correction. Press “Left” or “Right” to select.
English-21 English Calibration Before proper calibration can be performed, display should warm-up for a minimum of 30 minutes. If trying to start calibration before the monitor is warmed-up, a warning will appear on the screen (Figure 1) . Figure A 2.
English-22 6. Press SELECT to start the calibration. Front sensor calibration may take several minutes depending on user setting. 7. After the CALIBRA TION SUCCEEDED message appears ( Figure 6 ), press SELECT . T o end the calibration mode, press “EXIT”.
English-23 English 5. Press SELECT on Display B to start reading the white point* and luminance information of Display A. 6. After copying the Display A information, the target luminance and target chromaticity coordinates will be stored and displayed in the OSD of Display B.
English-24 DICOM Measurement 1. T o show the CALIBRA TION menu, select the CALIBRA TION in the advanced menu (page 20). 2. Select DICOM MEASURE in the Mode selection ( Figure 17 ). 3. Select the Color setting in COLOR* 2 selection and Gamma setting in GAMMA selection.
English-25 English Specifications - MD212MC Monitor Specifications MD212MC Monitor Notes LCD Module Diagonal: 54.0 cm/21.3 inches Active matrix; thin film transistor (TFT) V iewable Image Size: 54.0 cm/21.3 inches liquid crystal display (LCD); UA - SFT (IPS); Native Resolution (Pixel Count): 1200 x 1600 (Portrait) 0.
English-26 Specifications - MD213MC Monitor Specifications MD213MC Monitor Notes LCD Module Diagonal: 54.0 cm/21.3 inches Active matrix; thin film transistor (TFT) V iewable Image Size: 54.0 cm/21.3 inches liquid crystal display (LCD); UA - SFT (IPS); Native Resolution (Pixel Count): 1536 x 2048 (Portrait) 0.
English-27 English Specifications - MD213MG Monitor Specifications MD213MG Monitor Notes LCD Module Diagonal: 54.0 cm/21.3 inches Active matrix; thin film transistor (TFT) V iewable Image Size: 54.0 cm/21.3 inches liquid crystal display (LCD); SA - SFT (IPS); Native Resolution (Pixel Count): 1536 x 2048 (Portrait) 0.
English-28 Features DVI-I: The integrated interface ratified by the Digital Display W orking Group (DDWG) that allows both digital and analog connectors off of one port. The “I” stands for integration for both digital and analog, The digital portion is DVI-based.
English-29 English T roubleshooting No picture • The signal cable should be completely connected to the display card/computer . • The display card should be completely seated in its slot. • Power Switch and computer power switch should be in the ON position.
English-30 NEC DISPLA Y SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’ s top priorities in trying to minimize the burden placed on the environment.
Ein wichtiger Punkt beim Kauf des Geräts NEC MD213MC (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie NEC MD213MC noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für NEC MD213MC - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von NEC MD213MC reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über NEC MD213MC erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon NEC MD213MC besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von NEC MD213MC verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit NEC MD213MC. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei NEC MD213MC gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
