Benutzeranleitung / Produktwartung WD2000 des Produzenten Mitsubishi Electronics
Zur Seite of 40
WD2000 DLP™ PROJECTOR MODEL WD2000 User Manual This User Manual is important to you. Please r ead it befor e using your pr ojector . ENGLISH.
EN-2 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE P ARTS INSIDE REFER SERVICING TO QUALIFIED SER VICE PERSONNEL.
EN-3 ENGLISH Contents Important safeguards ........................................................................................................................ 4 Preparing your pr ojector ...........................................................
EN-4 Important safeguar ds Please read all these instructions r egar ding your projector and r etain them for futur e refer ence. Follow all warnings and instructions marked on the projector . 1. Read instructions All the safety and operating instructions should be read befor e the appliance is operated.
EN-5 ENGLISH WARNING: Unplug immediately if there is something wrong with your pr ojector . Do not operate if smoke, strange noise or odor comes out of your projector . It might cause fi re or electric shock. In this case, unplug immediately and contact your dealer .
EN-6 Pr eparing your pr ojector 1 2 3 Checking accessories The following accessories are pr ovided with this pr ojector . Check to be sure that all of the accessories ar e packed in the package. Important: • The attached power cords ar e to be used exclusively for this pr oduct.
EN-7 ENGLISH Overview Control panel T erminal boar d 1 2 6 7 8 4 5 3 POWER MENU ENTER ST A TUS AUTO POSITION COMPUTER ZOOM/FOCUS LENS SHIFT KEYSTONE VIDEO VOLUME 1 5 6 2 3 4 7 8 9 11 10 1 Speaker 2 Co.
EN-8 1 2 Preparating your projector (continued) Bottom side 1 Lamp cover 2 Adjustment feet Caution: Do not replace the lamp immediately after using the projector because the lamp would be extremely hot and it may cause burns.
EN-9 ENGLISH Using the r emote contr ol Operational range of the r emote contr ol • Keep the remote contr ol photo-sensor out of dir ect sunlight or fl uor escent lamp light. • Keep the remote control photo-sensor at least 2 m away from fl uorescent lamps.
EN-10 W A A=B B Setting up your pr ojector Setting up the screen Install the screen perpendicularly to the pr ojector . If the screen can not be installed in such a way , adjust the projection angle of the pr ojector .
EN-11 ENGLISH Caution: • Placing the pr ojector directly on a carpet impairs ventilation by the fans, causing damage or failure. Put a hard boar d under the pr ojector to facilitate ventilation.
EN-12 40 102 24 61 32 81 19 49 32 81 2 6 2.6 7 54 1.4 74 1.9 12 30 2 6 3 8 60 152 36 91 48 122 29 73 48 122 4 9 3.8 10 82 2.1 112 2.8 18 46 3 9 5 12 80 203 48 122 64 163 38 98 64 163 5 12 5.1 13 110 2.8 150 3.8 24 61 4 11 6 16 100 254 60 152 80 203 48 122 80 203 6 15 6.
EN-13 ENGLISH 2 1 AUDIO OUT AUDIO IN 2 1 2 1 Viewing computer images A. Connecting the projector to a computer Preparation: • Make sure that the power of the pr ojector and that of the computer ar e turned off. • When connecting the projector to a desktop computer , disconnect the RGB cable that is connected to the monitor .
EN-14 2 1 1. Plug the attached power cord into the power cord inlet of this projector . 2. Plug the other end of the power cord into a power outlet. • The power cords for use in the U.S. and Eur ope ar e included with this projector . Use the appropriate one for your country .
EN-15 ENGLISH POWER MENU ENTER ST A TUS AUTO POSITION COMPUTER ZOOM/FOCUS LENS SHIFT KEYSTONE VIDEO VOLUME C. Projecting images Preparation: • Remove the lens cap. 1. Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up r ed.
EN-16 POWER MENU ENTER ST A TUS AUTO POSITION COMPUTER ZOOM/FOCUS LENS SHIFT KEYSTONE VIDEO VOLUME Viewing computer images (continued) T o stop pr ojecting: 13. Press the POWER button. • A confi rmation message is displayed. • T o cancel the procedure, leave the pr ojector for a while or pr ess any button except the POWER button.
EN-17 ENGLISH Connecting to a video player , etc. 1. Connect one end (yellow) of the supplied audio/video cable to the VIDEO IN terminal of the projector . 2. Connect one end (white and red) of the supplied audio/ video cable to the audio input terminals (L/MONO, R) of the projector .
EN-18 C B (P B ) Y C R (P R ) B G R AUDIO IN-2 BNC cable (option) DVD player or HDTV decoder BNC-RCA connector (option) COMPUTER/COMPONENT VIDEO IN-2 Connecting to video equipment having a DVI-D terminal Y ou can project high-quality images by connecting the DVI-D terminal of this projector to video equipment having a DVI-D output terminal.
EN-19 ENGLISH C. Pr ojecting images Preparation: • Remove the lens cap. 1. Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up r ed.
EN-20 T o stop pr ojecting: 13. Press the POWER button. • A confi rmation message is displayed. • T o cancel the procedure, leave the pr ojector for a while or pr ess any button except the POWER button. 14. Press the POWER button again. • The lamp goes out and the projector goes into a standby mode.
EN-21 ENGLISH Setting the aspect ratio Y ou can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Change the setting according to the type of the input video signal. How to change the settings: With the remote contr ol: 1.
EN-22 Menu operation • Menus are not displayed when no signal is supplied to the pr ojector . * 1: Not available when COLOR ENHANCER is set to sRGB. * 2: Not available with certain signals. * 3: Available only when the input signal is TV50, TV60, 480i or 576i.
EN-23 ENGLISH IMAGE opt. CONTRAST BRIGHTNESS 0 0 ST ANDARD 0 0 0 COLOR TINT SHARPNESS COLOR TEMP . AUTO COLOR ENHANCER XGA60 INST ALLATION opt. ON SPLASH SCREEN AUTO POWER OFF BACK COLOR LAMP MODE OFF.
EN-24 3. FEA TURE menu ITEM SETTING FUNCTION ASPECT AUTO Select to change the aspect ratio automatically depending on the input signal. (Select this option for normal use.) 16:9 This option allows you to select the display position of squeezed (or horizontally compressed) images stor ed on DVD discs.
EN-25 ENGLISH Adjusting pr ojected images T o adjust the brightness (CONTRAST and BRIGHTNESS): Y ou can make adjustments for the brightness of the projected image using the menu. (See page 22 for menu setting.) 1. Display the IMAGE menu. 2. Select CONTRAST or BRIGHTNESS by pressing the or button.
EN-26 T o adjust the tone of white (COLOR TEMP .): Y ou can select a preset color temperature (white tone) using the menu. (See page 22 for menu setting.) 1. Display the IMAGE menu. 2. Select COLOR TEMP . by pressing the or button. 3. Select your desired color temperature by pr essing the or button.
EN-27 ENGLISH This projector automatically and pr operly projects video signals supplied from the computer . However , some video signals may not be projected, depending on the type of the computer . In such a case, press the AUTO POSITION button. (See page 16.
EN-28 MENU ACCESS FEA TURE XGA60 opt. LOCK UNLOCK OK OK P ASSWORD CONFIRM O K CANCEL MENU ACCESS FEA TURE XGA60 opt. LOCK UNLOCK OK OK P ASSWORD O K CANCEL Password function This projector is equipped.
EN-29 ENGLISH Mouse r emote contr ol By connecting to personal computer through the USB port, you can operate your computer with the pr ojector remote control. Projector + computer with USB connector Operation • Y ou can use the mouse remote contr ol function with a computer supporting USB only .
EN-30 Supervising and contr olling by computer Y ou can supervise and control the projector’ s operation using a personal computer via a LAN network. • T o supervise and control the pr ojector , install the software “Mitsubishi Pr ojector Control Device Installer *” con- tained in the attached CD-ROM.
EN-31 ENGLISH Indicators POWER Steady green or Steady red Steady red Steady green Steady red Steady red Blinking green/red Blinking green/red ST A TUS Blinking orange Blinking green Blinking green/red Blinking red Steady red Off Steady or Blinking CONDITION Abnormal temperature • The ventilation grilles are clogged with dust or dirt.
EN-32 Replacing the lamp This projector is equipped with a lamp to pr oject images. This lamp is a consumable. It may bur n out or its brightness may decrease during use. In such cases, r eplace the lamp with a new one as soon as possible. Be sure to replace the lamp with a new lamp separately sold that is exclusive to this projector .
EN-33 ENGLISH T o r eplace the lamp: 1. Reverse the projector gently . 2. Loosen the screw (a) using a Phillips screwdriver (+), and remove the lamp cover (b). 3. Loosen the screws (c) using a Phillips screwdriver (+). 4. Pull up the handle. 5. Pull out the lamp box by the handle while holding the projector .
EN-34 POWER Off Steady red Blinking red / green ST A TUS Off Off Blinking orange Blinking green Steady red Off Steady or Blinking Solution • Connect the power cord to the projector . • Plug the power cord into a wall outlet. • If any objects are blocking the air inlet or outlet grille, remove them and carry out the following.
EN-35 ENGLISH Images are not displayed corr ectly . Problem Projected images ar e shaking. Projected images ar e displaced. Projected images ar e distorted. Projected images ar e dark. Projected images ar e blurred. White dots are seen on projected images.
EN-36 Problem The exhaust vents emit warm air . No audio is output. The menu can’t be used. “TEMPERA TURE!!” is displayed. The mark appears. The remote contr ol doesn’t function easily or at all. The buttons on the control panel (except for the POWER button) don’t function.
EN-37 ENGLISH Specifi cations The specifi cations and outside appearance of the pr ojector are subject to change without prior notice. *1 : Wireless LAN unit isn’ t packaged together with the projector .
EN-38 Signal mode Resolution Horizontal V ertical Normal mode Real mode (H x V) frequency (kHz) frequency (Hz) (H x V) (H x V) TV60, 480i (525i) - 15.73 59.94 1024 x 768 - *1 TV50, 576i (625i) - 15.63 50.00 1024 x 768 - *1 1080i 60 (1125i 60) - 33.75 60.
EN-39 ENGLISH 1 R(RED)/C R 2 G(GREEN)/Y 3 B(BLUE)/C B 4 GND 5 GND 6 GND 7 GND 8 GND 9 DDC 5V 10 GND 11 GND 12 DDC Data 13 HD/CS 14 VD 15 DDC Clock 1 - - 2 TXD IN 3 RXD OUT 4 - - 5 GND - 6 - - 7 - - 8 - - 9 - - 1 5 11 6 10 15 SERIAL (D-SUB 9-pin) Pin No.
MITSUBISHI Pr ojector Contact Information Manufactur ed by Mitsubishi Electric Corporation 1 Zusho Baba, Nagaokakyo-City , Kyoto Japan M I T SUBIS HI ELECTRIC CORPORA T I O N North America MESCA (Mitsubishi Electric Sales Canada Inc.) http://www .mitsubishielectric.
Ein wichtiger Punkt beim Kauf des Geräts Mitsubishi Electronics WD2000 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Mitsubishi Electronics WD2000 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Mitsubishi Electronics WD2000 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Mitsubishi Electronics WD2000 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Mitsubishi Electronics WD2000 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Mitsubishi Electronics WD2000 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Mitsubishi Electronics WD2000 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Mitsubishi Electronics WD2000. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Mitsubishi Electronics WD2000 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
