Benutzeranleitung / Produktwartung Q173CPU(N) des Produzenten Mitsubishi Electronics
Zur Seite of 234
IB(NA)-0300040-B(0205)MEE MOTION CONTROLLER Qseries (Q173CPU ( N ) /Q172CPU ( N )) User's Manual U Q MOTION CONTROLLERS Q173CPU ( N ) Q172CPU ( N ) User's Manual MODEL MODEL CODE Q173/Q172CP.
A - 1 SAFETY PRECAUTIONS (Read these precautions before using.) When using this equip ment, thoroughly read this manual and the associated manuals introduced in t his manual. Also pay careful a ttention t o safety and handle the module properly. These precautions apply only to this equipment .
A - 2 For Safe Oper ation s 1. Prevention of electric shocks ! DANGER Never open the front case or terminal covers while the pow er is ON or the unit is running, as this may lead to elect ric shocks. Never run the unit with the front case or term inal cover removed.
A - 3 3. For injury prev ention ! CAUTION Do not apply a volt age other than that specified in the instruction manual on any terminal. Doing so may lead t o destruction or damage. Do not mistake the terminal connections, as this may lead to destruction or damage.
A - 4 ! CAUTION In systems where perpendicular shaft dropping may be a problem during the forced stop, emergency stop, servo O FF or power supply OFF, use both dynamic brakes and electromagnetic bra kes. The dynamic brakes must be used only on errors that cause the forced stop, e mergency stop, or servo OFF.
A - 5 ! CAUTION Set the servomotor encoder type (increment, absolute position ty pe, etc.) param eter to a value that is compatible with t he system application. The protectiv e functions may not function if the settin g is i ncorrec t. Set the servomotor capacity and ty pe (standard, low-inertia, flat, etc.
A - 6 ! CAUTION Do not get on or place heavy objects on the product. Always observ e the installation direction. Keep the designated clear ance between the Motion controller or servo amplifier and cont rol panel inner surface or the Motion controller and servo amplifier, Motion controller or serv o amplifier and other devices.
A - 7 (4) W iring ! CAUTION Correctly and securely wire the wires. Reconfirm the connect ions for mistakes and the terminal screws for tightness after wiring. Failing to do so may lead t o run away of the servomotor. After wiring, install the protectiv e covers such as the terminal covers to the original positions.
A - 8 (6) Us age methods ! CAUTION Immediately turn OFF the power if smoke, abnor mal sounds or odors are emitted from the Motion controller, servo amplifier or servomotor. Always execut e a test operation before star ting actual operations after the program or parameters have been changed or after maintenance and inspection.
A - 9 ! CAUTION If an error occurs, remo ve the cause, secure the safety and then resume operation after alarm release. The unit may suddenly resume operation after a pow er failure is restored, so do not go near the machine. (Design t he machine so that personal safety can be ensured even if the machine restarts suddenly.
A - 10 (9) About processi ng of waste W hen you dis car d Moti on contr oller , ser vo am plif ier, a batter y (pr imar y batt ery) a nd o ther o ption articl es, pleas e foll ow the law of eac h coun try (ar ea).
A - 11 REVI SION S The manual number i s given on the bottom left of the b ack cov er. Pri nt D ate Manual Num ber Revision Nov., 20 01 IB(NA)-0300 040-A First edi tion May.
A - 12 INTRODUCT ION Thank you for choos ing the Q173CPU( N)/Q17 2CPU(N ) Motion C ontroller . Please r ead this m anual caref ully so tha t equi pment is used to its optim um . CONTENT S Safet y Precaut ions ..........................................
A - 13 4. IN STALL ATION AND W IRING 4- 1 t o 4-2 0 4.1 Mod ule Ins tallat ion ........................................................................................................ ........................... 4- 1 4.1.1 Ins truct ions f or ha ndlin g .
A - 14 APPE NDICES App- 1 to App- 37 APPENDIX 1 Ca bl es .............................................................................................................. ....................App- 1 APPEN DIX 1.1 SS CNET cables ...........................
A - 15 About Ma nuals This manual is only to exp lain hardwar e of the Mo tion controller . The f ollowing m anuals are relate d to th is prod uct. Referr ing to this lis t, pl ease reques t the nec essar y manua ls.
A - 16 (2) PLC Manual N ame Manual N umber (Model Code) QCPU User's Manual (Hardw are Design, Maintenance and Inspection) This manual expl ains the s pecifi cations of t he QCPU modules , power supply modul es, base m odules, extension c ables, m emory card batt ery and others .
1 - 1 1 OVERVIE W 1. OVERVIEW 1.1 Overv iew This User's Manua l desc rib es the hard ware s pecif icati ons a nd h andlin g meth ods of the Motion Contr oller's Mod el Q 173CPU( N)/Q17 2CPU( N) f or th e Q ser ies PLC M ultip le CP U sy st e m.
1 - 2 1 OVERVIE W Generic term/Abbreviation Description Dividing unit Dividing unit (Q173DV) Battery unit Battery unit (Q170BAT) A 0BD -PCF A10BD-PCF/A30BD-PCF SSC I/F board SSC I/F communication .
2 - 1 2 SYSTEM CONFIG URATION 2. SYSTEM CONFIGURATION This section d escri bes the Q17 3CPU(N) /Q1 72CPU( N) s ystem conf igur ation, preca utions on us e of s yste m and conf igure d equ ipm ents.
2 - 2 2 SYSTEM CONFIG URATION (a) W hen using the D ividing unit/exter nal battery It is poss ible t o select the best accor ding to t he system. Power supply module/ QCPU/ I/O module/ Intelligent fun.
2 - 3 2 SYSTEM CONFIG URATION (b) W hen using the Dividi ng cable MIT SUB ISHI Powe r supp ly mod ule/ QCPU/ I/O module/ Intelligent functi on module of the Q series Motion CP U module (Q173 CPU (N)) .
2 - 4 2 SYSTEM CONFIG URATION (2) Equipment configuration in Q172CPU(N) system Q172CPU(N) S ystem configurat ion Is this system continuously power off for 1000 hours or more running? YES NO (Note) Refer to equ ipment configu ration o f "(a) Wh en using the externa l battery" .
2 - 5 2 SYSTEM CONFIG URATION (a) W hen using the exter nal battery MITSUBIS HI LITHIU M BATTERY Battery unit (Q170BAT) (Note-1) MITSUBISH I LITHIUM BATT ERY BAT CPU Q17B AT DATE PASSED Pow er sup ply.
2 - 6 2 SYSTEM CONFIG URATION (b) W hen not using the ex ternal battery MITSUBISHI CPU base unit (Q33B, Q35B, Q38B, Q312B) It is possible t o select the best accordi ng to the system.
2 - 7 2 SYSTEM CONFIG URATION (3) Peri pheral device configur ation for the Q173C PU(N) / Q172CPU(N) The following (a) (b) (c) can be used. (a) RS-232 configu ration RS-232 cable (QC30R2) Personal com.
2 - 8 2 SYSTEM CONFIG URATION 2.1.1 Q173CPU(N ) System overal l configurati on M a n u a l p u l s e g e n e r a t o r i n t e r f a c e m o d u l e S y n c h r o n o u s e n c o d e r i n t e r f a c.
2 - 9 2 SYSTEM CONFIG URATION CAUTION Constr uct a safet y circ uit ex tern all y of the Motion contr oller or s ervo amplif ier if the abnor mal operat ion of the Motion con trol ler or s ervo am plifier diff er fr om the s afet y direc tive opera tion in th e sy st em.
2 - 10 2 SYSTEM CONFIG URATION 2.1.2 Q172CPU(N ) System overal l configurati on M a n u a l p u l s e g e n e r a t o r i n t e r f a c e m o d u l e S y n c h r o n o u s e n c o d e r i n t e r f a .
2 - 11 2 SYSTEM CONFIG URATION CAUTION Constr uct a safet y circ uit ex tern all y of the Motion contr oller or s ervo amplif ier if the abnor mal operat ion of the Motion con trol ler or s ervo am plifier diff er fr om the s afet y direc tive opera tion in th e sy st em.
2 - 12 2 SYSTEM CONFIG URATION 2.1.3 Function expl anation of the Q17 3CPU(N )/Q172CPU(N) Motion CPU modules (1) Up to 3 2 axes ser vo am plifier s per 4 s ystem s (up t o 8 ax es p er 1 s ystem ) can be used i n Q17 3CPU(N) . Up to 8 ax es s ervo am plif iers p er 1 s ystem can be use d in Q172CPU(N) .
2 - 13 2 SYSTEM CONFIG URATION 2.1.4 Restrictions on Moti on systems (1) It is not al lowed t o us e the Motion CPU as th e contr ol C PU of a modu le ins tall ed on the QA1 S6 B extens io n bas e unit .
2 - 14 2 SYSTEM CONFIG URATION (12) N um ber of M otion CPU m odules and t emper ature condit ions (Q1 73CP U/ Q172 CPU on ly ) (a) It is p ossibl e to rem ove the Cooli ng fan unit(Q 170F AN) i n ord.
2 - 15 2 SYSTEM CONFIG URATION 2.2 System Config uration Eq uipment (1) Table of Moti on controll er related module Part nam e Model nam e (Note-1) Descr iption Current consumpt ion 5VDC[A] Remark Q172CPUN Up to 8 axes cont rol 1.14 Q172CPUN-T Up to 8 axes cont rol, For teac hing unit 1.
2 - 16 2 SYSTEM CONFIG URATION Table of Moti on controller r elated module (conti nued) Part nam e Model nam e (Note-1) Descr iption Current consumpt ion 5VDC[A] Remark QC05B Length 0. 45m(1.48ft.) QC06B Length 0. 6m(1.97ft.) QC12B Length 1. 2m(3.94ft.
2 - 17 2 SYSTEM CONFIG URATION Table of Moti on controller r elated module (conti nued) Part nam e Model n ame (Note-1) Descr iption Current consumpt ion 5VDC[A] Remark MR-J 2CN S Q172EX(-S1) s ide co.
2 - 18 2 SYSTEM CONFIG URATION Table of Moti on controller r elated module (conti nued) Part nam e Model nam e (Note-1) Descr iption Current consumpt ion 5VDC[A] Remark Q172CPU(N) connect or set Q172C.
2 - 19 2 SYSTEM CONFIG URATION (2) Q seri es PLC module w hich can be control by Motion CPU Part nam e Model name Descr iption Remark AC QX10 100-120VAC, 7-8mA, 16 point s, Termi nal block QX40 24VDC/.
2 - 20 2 SYSTEM CONFIG URATION (3) Table o f servo amplifier The f ollowi ng ser vo am plif ier series can be use d. (a) MR-H BN Part nam e Model nam e Descript ion MR-H BN MR-H ser ies servo am plifier MR-H KBN Refer t o catalogue of the servo am plifi er.
2 - 21 2 SYSTEM CONFIG URATION (b) MR-J2 S- B/MR-J2M-B/MR-J2- B/MR- J2-03B5 Part nam e Model n ame Desc ription MR-J 2S- B MR-J2-Super s eries servo am plifier MR-J 2S- B1 Ref er to catal ogue of the se rvo amplif ier.
2 - 22 2 SYSTEM CONFIG URATION (c) FR-V5 0- Part nam e Model n ame Descript ion FR-V520- K FR-V500 series vector inverter FR-V540- K Refer to c atalogue of t he vector inv erter. Q172J2BCBL M • MR-J2 -B (Note-1) FR-V5NS (Note-2) 0.5m(1.6 4ft.), 1m(3.
2 - 23 2 SYSTEM CONFIG URATION (5) Operati ng environment o f personal computer Oper ating env iron ment is shown below . IBM PC/AT with which WindowsNT4.
2 - 24 2 SYSTEM CONFIG URATION 2.3 General Speci fications Gener al spec ificati ons o f Q173CP U(N)/Q 172CPU( N) modul e are show n below . Item Specification Operating ambient temperature 0 to 55°C.
2 - 25 2 SYSTEM CONFIG URATION ! CAUTION The Motion controller must be stored and used under the condit ions listed in the table of specifications ab ove. When not using the module for a long time, disconnect t he power line from the Motion controller or servo amplifier.
2 - 26 2 SYSTEM CONFIG URATION 2.4 Specifications of E quipment and Setti ngs 2.4.1 Name o f parts for CPU modul e This sect ion ex plains the nam es and s ettin g of the m odul e. (1) Q173CPU N(-T)/Q172CPUN (-T) Front f ace Q17 CPU N T RS-232 USB MODE RUN ERR.
2 - 27 2 SYSTEM CONFIG URATION (2) Q173CPU /Q172CPU Front f ace Q17 CPU RS-232 USB MODE RUN ERR. M.RUN BAT. BOOT 2) 8) 3) 4) 5) 6) 7) PULL Put your finger h ere to open the cover. FRONT SSCNET CN2 CN1 W ith front co ver o pen MODE RUN ERR. M. RUN BAT.
2 - 28 2 SYSTEM CONFIG URATION No. Nam e Applic ation 1) Module fi xing hook • Hook used to fi x the module to t he base unit.(Quic k release ins tallat ion) 2) MODE LED (Mode judgi ng) • Lit(gree.
2 - 29 2 SYSTEM CONFIG URATION (3) Appli cations of switches, connectors on Q 173CPU(N )/ Q172CPU(N ) No. Nam e Applicati on Dip switch 1 Must not be used.
2 - 30 2 SYSTEM CONFIG URATION (4) Basic speci fications of Q173CPU(N) /Q172CPU(N) (a) Modul e specifications Item Q173CP UN Q173CPUN-T Q173CPU Q172CPUN Q172CPUN-T Q172CPU Teaching unit —— Us able —— —— Usable —— Internal c urrent consumpt ion(5VDC) [A ] 1.
2 - 31 2 SYSTEM CONFIG URATION Motion control speci fications (continued) Item Q173C PUN(-T) Q173CPU Q172CPUN(-T) Q172CPU Synchronous encoder operation function Possible to connect 12 modules Possible.
2 - 32 2 SYSTEM CONFIG URATION (b) Moti on SFC performance specifications Item Q173CPU(N)/Q172CPU(N) Code total (Motion SFC chart+ Operation control+ Transition) 287k bytes Motion SFC program capacity Text total (Operation control+ Transition) 224k bytes Number of Motion SFC programs 256(No.
2 - 33 2 SYSTEM CONFIG URATION (6) SV43 Moti on control specificat ions/per formance specifications (a) Motion contr ol specifications Item Q173CPUN Q173CPU Q172CPUN Q172CPU N umber of control ax e s Up to 32 axes U pt o8a x e s Operation cycle (default) 0.
2 - 34 2 SYSTEM CONFIG URATION (b) Moti on program performance speci fications Item Q173CPU(N)/Q172CPU(N) Total of program files 248k bytes Program capacity Number of programs Up to 1024 (No.
2 - 35 2 SYSTEM CONFIG URATION (7) Selecti on of Q172EX, Q173PX Synchronous encoder Item Serial absolute Incremental Manual pulse generator Q173CPU(N) 12 modules Q172CPU(N) 8 modules 3 modules Module .
2 - 36 2 SYSTEM CONFIG URATION 2.4.2 Power supply module (1) Table o f the power supply module specificati ons This secti on describ es the power supply module s specificatio ns.
2 - 37 2 SYSTEM CONFIG URATION The po wer s upp ly mod ule s pecif icat ions (c ont inued) Perform ance spec ificati ons Item Q63P Q64P Base loadi ng position Power s upply module l oading slot Applicabl e base unit Q33B, Q35B, Q38B, Q312B, Q65B, Q68B, Q612B Input po wer supply 24VDC (+30%/-35% ) (15.
2 - 38 2 SYSTEM CONFIG URATION POINTS (Note- 1) : Overc urren t prote ction The ov ercur rent protec tion devi ce shu ts off t he 5V DC or 24VDC circui t and st ops th e s ystem if the curren t flow ing in the c ircui t excee ds t he specif ied valu e.
2 - 39 2 SYSTEM CONFIG URATION (2) Names of Parts and Setti ng This sect ion des cribes the nam es of the p arts of eac h power m odule. (a) Q61P-A1, Q61P- A2, Q62P, Q63P, Q64P Q61P-A1 POWE R 100 -12 0VAC INPUT 50/60Hz 105VA OUTPUT 5VDC 6A ERR. L +- 24VDC 0.
2 - 40 2 SYSTEM CONFIG URATION No. Name Application 1) POWER LED 5VDC power indicator LED 2) ERR terminals Turned OFF (opened) when a stop error occurs in the CPU module. Normally off w hen loaded in an extension base unit. 3) FG terminal Ground terminal connected to t he shield pattern of the printed circuit board.
2 - 41 2 SYSTEM CONFIG URATION (3) Selecti on of the pow er supply module The po wer s uppl y modu le is select ed ac cordi ng to the to tal of curr ent consum ption of t he I/O m od ules, s pec ial func tion m odule, an d per ipher al de vices suppl ied b y its p ower m odu le.
2 - 42 2 SYSTEM CONFIG URATION (4) Example of the po wer supply selection calculati on ( W hen using the Q173 CPUN-T.) (a) System c onfigur atio n Q38B Q173PX Q173 CPUN-T Q172LX Q172 EX QX 40 QX40 QY10 QY10 MR-HDP01 Q02H CPU Q61P-A 1 MR-HDP01 MR-H ENC A31TU-D3K13 (b) 5 VDC cur rent c onsum pti on of e ach m odule Q02HCP U : 0.
2 - 43 2 SYSTEM CONFIG URATION 2.4.3. Base unit and ex tension cable This sect ion des cri bes th e spec if icatio ns of the ex tens ion c ables for t he b ase u nits (CPU base unit or ex tens ion base unit) used in th e s ystem , and t he s pecif icat ion standar ds of the extens ion base u nit.
2 - 44 2 SYSTEM CONFIG URATION (2) Table of the extension cable speci fications The l ist be low des cribes th e spec ific ations of the ex tensi on cab les which can be us ed for the QCPU sy stem. Type Item QC05B QC06B QC12B Q C30B QC50B QC100B Cable length[m(ft.
2 - 45 2 SYSTEM CONFIG URATION (4) I/O allocations It i s po ssible to al locate uni que I /O No .s fo r ea ch Moti on CP U in depende ntly of the PL C’s I/O No. s. (I /O No.s a re uniq ue betw een th e Q seri es PLC CPU with in a given s ystem , but the I/O No.
2 - 46 2 SYSTEM CONFIG URATION 2.4.4 Q172LX Ser vo external si gnals interface module Q172LX rec eives exter nal s ign als (s ervo exter nal s ignal s) r equir ed for posit ion ing control. (1) Q172LX name of parts 5) 6) 2) 4) 3) 1) CTRL Q172LX Q1 72LX No.
2 - 47 2 SYSTEM CONFIG URATION (2) Performance speci fications (a) Modul e specifications Item Specifications Number of I/O occupying point s 32 points(I/O allocation: Intell igent, 32 points) Internal current consumption(5 VDC) [A] 0.05 Exterior dimensions [ mm(inch)] 98(H) 27.
2 - 48 2 SYSTEM CONFIG URATION (3) Connecti on of servo exter nal signal s interface module (a) Serv o external signals There are th e followi ng servo e xternal signal s. (Upper str oke l imit is lim it va lue of ad dress incr ease d irec tion/ lower s trok e lim it is lim it value of an addr ess decreas e dir ecti on.
2 - 49 2 SYSTEM CONFIG URATION (b) The pin lay out of the CTRL connector Use the CTRL c onnec tor at the Q 172LX modu le fro nt to connect the s ervo exte rnal si gnals. The f ollowi ng pin la yout of t he Q17 2LX CT RL co nnect or vie wed f rom the front.
2 - 50 2 SYSTEM CONFIG URATION (4) Interface betw een CTRL connector and s erv o external signal RLS Input or Output Signal name Interna l circuit FLS Stop signal input STOP DOG/CHANGE 12VDC to 24VDC .
2 - 51 2 SYSTEM CONFIG URATION 2.4.5 Q172EX Ser ial absolute synchr onous encoder interface modul e Q172EX rec eive extern al si gnals r equ ired f or ser ial abs olut e s ynchron ous e ncoder . (1) Q172EX /Q172EX-S1/Q172EX-S2/Q172E X- S3 name of parts 2 1 TREN SY.
2 - 52 2 SYSTEM CONFIG URATION (2) Performance speci fications (a) Modul e specifications Specifications Item Q172EX Q172EX -S1 Q172EX-S2 Q172EX-S3 Memory for data ex change None Provided None Provided Number of I/O occupying point s 32 points(I/O allocation: Intell igent, 32 points) Internal current consumption(5 VDC)[A] 0.
2 - 53 2 SYSTEM CONFIG URATION (c) Seri al absolute synchronous encoder inp ut Item Specifications Applicable signal types Differential- output type : (SN75C 1168 or equivalent) Transmission m ethod Serial communications Synchronous method Counter-clock-wise (v iewed from end of shaft) Communication spee d 2.
2 - 54 2 SYSTEM CONFIG URATION (3) Select to number of the sy nchronous encoder modules Syn chronou s encode rs are avai labl e in voltag e output ty pe(in crementa l), di ffere ntial ou tput type (incr ementa l) a nd seria l absol ute output type (MR-HE NC).
2 - 55 2 SYSTEM CONFIG URATION (4) Connecti on of synchronous encoder inter face module. (a) Connecti on with serial absolute sy nchronous encoder (MR- HENC/Q170EN C) Use the SY.E NC con nector at th e Q172 EX m odule f ront to c onnec t the seri al ab solute synchron ous en coder( MR-HE NC/Q17 0ENC).
2 - 56 2 SYSTEM CONFIG URATION (5) Interface betw een SY.EN C connector and ex ternal equipment Pin No. SY .ENC co nnec tor Serial abs olut e synchronous enco der Input or Output Signal nam e Wiring example 12VDC to 24V DC Input MR 7 MRR 17 P5 10 18 19 20 LG 1 2 3 1 1 12 BAT 9 TREN 4 TREN.
2 - 57 2 SYSTEM CONFIG URATION (6) Detail s of encoder cable connections (a) Q172EX (-S1) 1) W hen not us ing tr acking enab le sign al MR-JHSCBL10 M-H to MR-JHSCBL30M-H (10 t o 30 m (32 .81 to 98.4 3ft .)) P5 19 LG 11 P5 20 LG 12 MR 7 MRR 17 BT 9 LG 1 SD S R C F G N D P5 19 LG 11 P5 20 LG 12 P5 18 LG 3 BT 9 LG 1 SD S F G N R C D SY.
2 - 58 2 SYSTEM CONFIG URATION (b) Q172EX -S2/Q172EX-S3 1) W hen not us ing tr acking enab le sign al (Note-1) SDplate 20 12 18 2 S H J N R K L SY.ENC side connector 10120-3000 VE ( connector) 10320-5.
2 - 59 2 SYSTEM CONFIG URATION (7) Connecti on of the battery This secti on de scribes t he bat tery speci fication s, han dling precau tion s and insta llatio n of the Q1 72EX. (a) Specifications The spec ific ations of the bat ter y for mem or y back -up ar e shown in th e tabl e belo w.
2 - 60 2 SYSTEM CONFIG URATION (c) Battery service life time Battery service life time Guaranteed time(M IN) [ h ] Actual time(TYP) [ h ] MR-HENC 1 pcs. 10000 30000 MR-HENC 2 pcs. 5000 15000 Q170ENC 1 pcs. 8000 24000 Q170ENC 2 pcs. 4000 12000 CAUTION Do not short a battery.
2 - 61 2 SYSTEM CONFIG URATION 2.4.6 Q173PX M anual pulse gener ator interface module Q173P X receive e xterna l signal s requir ed for Ma nual pul se gene rator and Incre mental syn chronou s encode r (Volt age- output /Open coll ecto r type /Diffe rent ial-ou tput ty pe).
2 - 62 2 SYSTEM CONFIG URATION No. Name Application Detection setting of T REN1 signal SW 1 SW 2 Dip switch 1 OFF OFF ON ON ON OFF TREN is detected w hen TREN signal turns off to on. Dip switch 2 OFF ON TREN is detected when TREN signal turns on to off.
2 - 63 2 SYSTEM CONFIG URATION (2) Performance speci fications (a) Modul e specifications Specifications Item Q173PX Q173PX -S1 Memory for data ex change None Provided Number of I/O occupying point s 32 points(I/O allocation: Intell igent, 32 points) Internal current consumption(5 VDC)[A] 0.
2 - 64 2 SYSTEM CONFIG URATION (c) M anual pulse generator/Incr emental synchronous encoder input Item Specifications Number of modules 3/module High-voltage 3.0 to 5.25VDC Voltage-output/ Open collector type Low-voltage 0 to 1.0VDC High-voltage 2.0 to 5.
2 - 65 2 SYSTEM CONFIG URATION (3) Connecti on of manual pulse g enerator Manu al puls e ge nerator s ar e av ailab le in volt age ou tput /open coll ector type and di fferent ial ou tput ty pe. Sinc e the se type s differ in connect ion method , design accord ing to th e connec tion m ethod of sectio n 2.
2 - 66 2 SYSTEM CONFIG URATION (5) Connecti on of manual pulse g enerator i nterface module (a) The pin lay out of the PULSER connector Use the PUL SER con nec tor at the Q 173PX modul e fron t to co nnect t he manual puls e s ignals , incr em ental s ynchr onous enc ode r sign als.
2 - 67 2 SYSTEM CONFIG URATION (b) Interface betw een PULSER connector and manual pulse generator (Differential output ty pe)/Incremental synchronous encoder Interface betw een Manual pulse g enerator (Differential outp ut type)/ Incremental sy nchronous encoder Input or Outp ut Sig nal n ame Pin No.
2 - 68 2 SYSTEM CONFIG URATION (c) Inter face between PULSER connector an d manual pul se generator (Voltage output/Open collector ty pe)/ Incremental sy nchronous encoder.
2 - 69 2 SYSTEM CONFIG URATION (6) Connecti on examples of manual pulse g enerator Connection of manual puls e generator Connection of m anual pulse generator (Vo ltage-output /Open c ollect or type) .
2 - 70 2 SYSTEM CONFIG URATION 2.4.7 Manual pulse g enerator/Ser ial absolute sy nchronous encoder (1) Table of the Manu al pulse gener ator specifications Item Specifications Model name MR-HDP01 Ambi.
2 - 71 2 SYSTEM CONFIG URATION (2) Table o f the Serial absolut e sy nchronous encoder speci fications Specifications Item MR-HENC Q170ENC (Note-1) Ambient temperature -5 to 55°C(23 to 131°F) Resolu.
2 - 72 2 SYSTEM CONFIG URATION 2.4.8 A31TU-D3 /A31TU -DN Teaching uni t (Japanese versi on only) Teachi ng unit A3 1TU- D3 /A31TU-D N can be easi ly set t he t eachi ng of p ositi oning point, eac h param eter setti ngs, cr eatio n of servo progra m , servo m onitor , ser vo tes t, and so on wit hout the per iphera l devices .
2 - 73 2 SYSTEM CONFIG URATION REMARK Exter nal saf et y circu it Constr uct th e circ uit (po wer s uppl y OFF of ser vomotor , etc.) of parts which m a y occur m achi ne bre akdo wn and acci dents due t o abnor mal opera tions outs ide of the Motio n CP U in a fa il-sa fe view poin t, to avoi d abno rmal o pera tion s of w hole syste m.
2 - 74 2 SYSTEM CONFIG URATION (2) A31 TU-D3 /A31TU- DN Name of parts DISABLE EMG.STOP ENABLE 5) 1) 2) 3) 4) 6) 7) A31TU DATA MONITOR TEST STOP OVERR IDE STEP - STEP + RETURN 8 ITE M # 9 CLEAR 5 DELETE E 6 INDI RECT F 3 C 2 B 0 MDI - 7 INST RUCTIO N ; 4 WRITE D 1 STORE A .
2 - 75 2 SYSTEM CONFIG URATION (3) Teaching uni t specifications Specif ications Items A31TU-D3 A31T U-DN Language Japanes e Tact sw itch 28 key s for SV ENABLE/DI SABLE sw itch Oper ation ena ble/dis.
2 - 76 2 SYSTEM CONFIG URATION 4) W hen the t each ing un it (A3 1TU-D 3 ) is not us ed, c onnec t th e short- circuit c onnec tor f or teac hin g unit ( A31T UD3TM) t o th e contr ol pan el side connect or of the ca ble for teachin g unit ( Q170TUD3C BL3M).
2 - 77 2 SYSTEM CONFIG URATION (b) Connecti on between the teaching unit (A31TU-DN ) and Motion CPU (Q173CPUN-T/Q172CPU N-T) There ar e f ollo wing two co nnec ting m eth od. • W hen the c onnec tor is co nnect ed to the c ontr ol pa nel. • W hen the c onnec tor is co nnect ed d irect ly in t he c ontro l pane l.
2 - 78 2 SYSTEM CONFIG URATION Connec tion exam ple bet ween the ca ble for te aching un it (Q1 70TUDN CBL3M) is shown be low. MITSUBI SHI Q173C PUN-T SSCNET M.RUN MODE RUN ERR. BAT. BOOT FRONT CN2 CN1 PULL USB RS-232 TU QX40 0 1 2 3 4 5 6 7 8 9 A B C D E F SY.
2 - 79 2 SYSTEM CONFIG URATION 2) W hen the c onnec tor is co nnecte d dir ect ly in th e contr ol p anel. a) Co nnec t the ca ble for teachi ng uni t (Q17 0TUD NCBL03M -A) to th e TU c onnector of Mot ion CP U (Q1 73CPUN-T /Q17 2CPUN- T) af ter connec ting t o the t eac hing u nit ( A31TU- DN ).
2 - 80 2 SYSTEM CONFIG URATION ! CAUTION Do not c onnec t the A31T U-D3 to the ca ble for teach ing unit (Q 170T UDNCBL03 M-A ). The protect ive functi on sto ps wor king.
2 - 81 2 SYSTEM CONFIG URATION (c) W hen not using a teaching uni t (A31TU-D3 /A31TU-D N ) Connec t a sh ort-cir cuit c onn ector for teac hing unit (Q17 0TUT M) to a TU connec tor of Moti on CPU (Q17 3CPUN- T/Q1 72CPUN- T) . Connec tion ex ampl e wit hout te achi ng un it (A31T U-D 3 /A31TU-DN ) is shown be low.
2 - 82 2 SYSTEM CONFIG URATION 2.4.9 SSCNET cables, ter minal connector and connection method This sectio n des cribes how t o co nnect betwe en the Mot ion CP U modu le a nd ser vo am plifiers . Betw een th e Motion CPU mo dule and servo a mplifi ers is conn ecte d by SSC NET cable.
2 - 83 2 SYSTEM CONFIG URATION (b) W hen using the Dividi ng cable CN1 Q173CPU(N) Motion CPU mod ule Servo amplifier MITSUBISHI CN1A CN1B MITSUBISHI CN1A CN1B MITSUBISHI CN1A CN1B MITSUBISHI CN1A CN1B 3) 3) 2) 4) 4) Servo a mplifier Servo amplifier Servo amplifier SSCNET cable over all length per 1 syste m 2)+total of 3) 30m(98.
2 - 84 2 SYSTEM CONFIG URATION List of SSCNET cabl e model na me No. Part nam e Model n ame (Note-2) Cable length Descript ion 1) Motion CPU Dividing unit Q173DVCBL M 0.5 m(1.64ft.) , 1m(3.28 ft.) Q173CPU(N) Dividing u nit (Q173DV) Q173J2B CBL M (Note-3) 0.
2 - 85 2 SYSTEM CONFIG URATION (2) Connecti on between the Q172CPU (N) and serv o amplifiers (a) W hen using the exter nal battery Batte ry u nit (Note-1) (Q170BAT) CN1 Q172CPU(N) Motion CPU mod ule S.
2 - 86 2 SYSTEM CONFIG URATION List of SSCNET cabl e model na me No. P art name Model n ame (Note-1) Cable length Descript ion Q172J2BCBL M- B 0.5m(1.64 ft.), 1 m(3.28 ft.), 5m(16.4 0ft.) Q172CPU(N) Servo ampli fier (MR-J2 -B) Battery unit ( Q170BAT) 1) Motion CPU Servo amplifier Battery unit Q172HBCBL M-B 0.
2 - 87 2 SYSTEM CONFIG URATION (3) Cable speci fications (a) Q172J2BCBL M (-B) Model name Item Q172J2BCBL05M(-B) Q172J2BCBL1M(-B) Q172J2BCBL5M(-B) Cable length [m(ft.)] 0.5( 1.64) 1(3.28) 5(16.40) (b) Q172HBC BL M (-B ) Model name Item Q172HBCBL05M(-B) Q172HBCBL1M(-B) Q172HBCBL5M(-B) Cable length [m(ft.
2 - 88 2 SYSTEM CONFIG URATION (h) FR-V 5NSCBL Model name Item FR-V5NSCBL005 FR-V5NSCBL01 FR-V5NSCBL05 FR-V5N SCBL10 FR-V5NSCBL20 Cable length [m(ft.)] 0.
2 - 89 2 SYSTEM CONFIG URATION (a) MR-H- BN configuration Motio n CPU module Battery MR-BAT , A6BA T Termina l connecto r Q173CPU(N) /Q172CPU(N) Battery MR-BAT , A6BAT Battery MR-BAT , A6BA T Q172CPU(.
2 - 90 2 SYSTEM CONFIG URATION (d) FR-V 5 0- + FR-V5 0- configuration Motion CPU module Q172CPU(N) Terminal connector sett ing i s se t by connector in FR-V5NS.
2 - 91 2 SYSTEM CONFIG URATION (h) MR-H -BN + FR -V5 0- configur ation Q172CPU(N) configuration : Q172HBCBL M Q173CPU(N) configuration : Q17 3HB CBL M Moti on CPU module Q173CPU(N) /Q172CPU(N) Terminal connector sett ing is se t by connector in FR-V5NS.
2 - 92 2 SYSTEM CONFIG URATION • FR-V5 0- + MR-J2 -B c onfig urat ion Motio n CPU module Q173CPU(N) Battery Q173 DV MR-BAT, A6BAT Q173DVCBL M Terminal connector sett ing is se t by connector in FR-V 5NS.
2 - 93 2 SYSTEM CONFIG URATION 2) Ex ample of Q172CPU( N) • MR-H-BN + MR-J2 -B + MR-H-BN configuratio n Battery Q170BAT Motion CPU modul e MR-BAT , A6BAT Termi nal connector Q172CPU(N) Battery MR-BA.
2 - 94 2 SYSTEM CONFIG URATION (5) Setting of the axis No. and axi s select switch of servo ampl ifier Axis No. is used to set the axis num bers of ser vo am plifi ers con nec ted to SSCNE T connector(CN ) in the program . Axis No. of 1 to 32 can be s et for Q 173C PU(N), and ax is No.
2 - 95 2 SYSTEM CONFIG URATION Correspondences between dno.s a nd axi s select switches of servo ampl ifier dno. (Note) SSCNET SYSTEM Servo ampl ifier' s rotary sw itch dno.
2 - 96 2 SYSTEM CONFIG URATION 2.4.10 External battery This sectio n descri bes the b atter y specif ica tions used in the Motion C PU, hand ling preca utions an d equi pment s. (1) Exter nal battery specifications(F or Motion CPU modul e) Model name Item A6BAT/MR-BAT Classification Manganese diox ide lithium primary battery Initial voltage [V] 3.
2 - 97 2 SYSTEM CONFIG URATION CAUTION Do not short a battery. Do not charge a battery. Do not disassemble a battery. Do not burn a battery. Do not overheat a battery. Do not solder the battery terminal. When using the external battery , be sure to select "th e external battery use" in the syst em settings.
2 - 98 2 SYSTEM CONFIG URATION (b) Connecti on with Q172CPU(N) Connec tion pr oced ure of Q17 2CPU(N) and A6BAT /MR-BAT 1) Set the A6BAT /MR-B AT t o the B atter y un it (Q17 0BAT ). 2) Con nect th e A 6BAT/MR- BAT conn ector t o the BAT connect or of Q170BA T.
2 - 99 2 SYSTEM CONFIG URATION 2.4.11 Cooling fan unit (Q170FAN ) (Q173CPU/Q172C PU only) This sect ion ex plains the s pecif icati ons of the Cooli ng fa n unit (Q 17 0FAN) used f or t he Motion C PU modul e.
2 - 10 0 2 SYSTEM CONFIG URATION (3) In point of the l ayout desig n within the control panel Leave 50mm (1.9 7inch) or m ore clear anc e betwe en th e top of the m odul es and structur es or parts . Top of pane l or wiri ng duc t 50mm (1.9 7in ch) min.
3 - 1 3 DESIGN 3. DESIGN 3.1 System Desi gning Procedure Design the s ystem which us es the Multi ple C PU s ystem i n the follo wing pr oced ure. Refer to s ection 2.
3 - 2 3 DESIGN Refer to sect ion 3.2 Refer to section 3. 2.1 Refer to sect ion 3.2.2 Refer to sect ion 3.3 Design th e power su pply circuit w hich suppl ies power to such system componen ts as the Moti on controll er, I/O equi pment and servo amplifier s, etc.
3 - 3 3 DESIGN ! CAUTION Do not touc h the s ervo ampl ifier's h eat ra diatin g fins , reg enerat ive resis tor an d ser vom otor, e tc. while t he p ower is ON and f or a shor t t ime af ter th e po wer is tur ned O FF. In th is t iming, these parts bec om e very hot and m a y lead to burns.
3 - 4 3 DESIGN 3.2 External Circuit Design As to t he ways to d esign the externa l circ uits of the Motion s y stem , this sect ion expla ins the m ethod and ins truc tions for desi gning th e power suppl y circuits and safety circui ts, etc.
3 - 5 3 DESIGN POINT 1) (Note-1) : The fol lowing is the Mo tion SFC pro gram example . < Example> For control axis 1 and axis 2 [F 1] SET PYm [G 1] M2408 M242 8 Servo er ror detectio n [F 2] RST PYm END 4) (Note-4) : It recommends u sing one leakage breaker for one s ervo amplif ier.
3 - 6 3 DESIGN (2) Sample sy stem circuit desig n for motion contr ol 2 (For A31TU- DN ) CP1 R S T +24V 24G COM COM NFB FG LG Q61P- A2 Xn CP2 Q173CPUN- T/ FLS1 DOG8 / CHAN GE8 EMG EMG SG Q170TUDNCBL3M.
3 - 7 3 DESIGN POINT 1) (Note-1 ) : The follow ing is the Moti on SFC pro gram example. < Example> For control axis 1 and axis 2 [F 1] SET PYm [G 1] M2408 M242 8 Servo er ror detectio n [F 2] RST PYm END 4) (Note-4) : It reco mmends using o ne leakage break er for one serv o amplifier.
3 - 8 3 DESIGN (3) Sample sy stem circuit desig n for motion contr ol 3 (For A31TU- D3 ) DC24VD CP1 RST +24V 24G FLS1 COM COM NFB 200VAC 200VAC FG LG Q61P-A2 Xn CP2 Emergency stop FLS1 DOG8/ CHANGE 8 .
3 - 9 3 DESIGN POINT 1) (Note-1) : The following is the Motion SFC program example. < Example> For control axis 1 and axis 2 [F 1] SET PYm [G 1] M2408 M2428 Servo error detecti on [F 2] RST PYm END 4) (Note-4) : It recommends using o ne leakage b reaker for o ne servo amplif ier.
3 - 10 3 DESIGN (4) System desig n circuit ex ample of the PLC I/O (a) System desig n circuit ex ample(when not usi ng ERR contact of power supply module) Starting p ossible when the PLC RUN outp ut R.
3 - 11 3 DESIGN (b) System desi gn circuit ex ample(when using ERR contact of power supply module) Interlock circu its as necessary. Provide external inte rlock circ uits for c onfl icti ng operati ons, such as forward r otation and reve rse ro tat ion, and for p arts that could damage the machi ne or cause acciden t if no interlo ck were used.
3 - 12 3 DESIGN 3.2.1 Power supply circuit desig n This se ction de scribe s the prote ctive coo rdina tion and noise suppressi on techni ques o f the po wer su ppl y circuit.
3 - 13 3 DESIGN 3.2.2 Safety cir cuit design (1) Concept of safety cir cuits W hen the Mo tion c ontro ller i s powere d on- off , proper outpu ts m ay not b e prov ided tempora r ily due to the de la ys an d rise times o f the Mo tion con trolle r power s uppl y and exter nal I/ O con trol p ower s uppl ies (e speci all y DC).
3 - 14 3 DESIGN (b) It is also possi ble to use t he f orced s top s igna l of th e ser vo am plif ier. Refer t o m anual of the serv o am plifier abo ut ser vom otor ca pacit y. Operat ion sta tus of the em ergenc y stop a nd t he forc ed s top are as fo llows.
3 - 15 3 DESIGN 3.3 Layout Desi gn within The Contr ol Panel 3.3.1 Installation env ironment Instal l the M otio n contr oll er s ystem in the f ol lowing envir onm ent con ditions . (1) Ambie nt tem pera tur e is within t he r ange of fol lowin g co ndit ions.
3 - 16 3 DESIGN 3.3.2 Layout desig n of the base uni ts This sect ion d escri bes th e p recau tions r elat ed t o inst all a M otio n contr o ller in an enclos ure.
3 - 17 3 DESIGN 3.3.3 Calculati ng heat gener ation by Motion contr oller The am bie nt tem peratur e in side t he con tro l pane l stor ing t he M otion c ontr oller mus t be suppr essed to a M otio n con troller oper atin g am bient t em perature of 5 5°C(1 31°F).
3 - 18 3 DESIGN (6) Power consumption of the power supply section of the intelligent function module W S = I 5V 5 + I 24V 24 + I 100V 100 [W ] The to tal of the p ower cons um ption values calc ulate d f or eac h b lock bec om es the po wer co nsum ption of the over all Mo tion s ystem .
3 - 19 3 DESIGN (e) A tota l of 24 VDC aver age po wer c onsum ption of th e out put m odule W 24V = 192 [W ] (8A/com m on) (f) Averag e po wer co nsum ption d ue t o vo ltage drop in the outp ut sec tion of th e outpu t modu le W OUT = 0 [W ] (g) A verag e power cons um ption of the input s ecti on of the i nput m odule W IN = 0.
3 - 20 3 DESIGN 3.4 Design Checkli st At the work site, c opy t he fol lowin g tab le for us e as a che ck sheet. Item Sub Item Design confirmation Check Number of ax es ax es Number of I/O points points Motion CPU module selecti on CPU module selecti on PLC CPU module selection Manual pulse generator pcs.
4 - 1 4 INSTALLATION AND W IRING 4. INSTALLATION AND W IRING 4.1 Module Install ation 4.1.1 Instructions for h andling ! CAUTION Use th e Mot ion c ontro ller in an envir onm ent th at meets the gener al sp ecific at ions c onta ined in this manual .
4 - 2 4 INSTALLATION AND W IRING (5) W hen an extens io n cab le is used, do not bin d the c able to geth er wit h the m ain circui t (hi gh vo ltage, heav y cu rrent) line or la y them clos e to each o ther . (6) Ins tall the CP U base unit ( b y screwing) in t he f ollowing proc edure.
4 - 3 4 INSTALLATION AND W IRING 4.1.2 Instructions for instal lation of the base unit Instal l th e Motio n con tro ller m odule to a panel , etc. , co nsid ering enoug h abo ut operab ilit y, maintai nabil ity and en vironm enta l resistanc e.
4 - 4 4 INSTALLATION AND W IRING (3) Moti on controller installati on orientation (a) S ince t he M otion c ontr oller gener ates h eat, it sho uld be fitt ed on a well vent ilated loca tion i n th e orient atio n sho wn be low. (b) Do not use it in ei ther o f the or ienta tions s hown belo w.
4 - 5 4 INSTALLATION AND W IRING 4.1.3 Installation and r emoval of module This sectio n ex plains how t o ins tall a nd rem ove a po wer s uppl y modul e, PL C CPU module , Mot ion C PU m odule, Motion m odule, I/O m odule , int ellig ent f unction m odule or an other module t o and from the base uni t.
4 - 6 4 INSTALLATION AND W IRING (b) Removal from Q3 B and Q6 B Module fixing hole Module Base unit Module conn ect or Completion Hold the m odule with b oth hands, and push the h ook on the top of the module with a finger until it stops. While pushing the hook, and using the bottom of the module as a support, pu ll the module tow ard yo u.
4 - 7 4 INSTALLATION AND W IRING 4.2 Installation and R emoval of Cable 4.2.1 SSCNET cable (1) Precauti ons for handling the SSC NET cable • Do not stam p the SSCNE T c able. • W hen layin g the SSCNET cab le, be s ure t o sec ure t he m inimum cable bend radius of 30 mm (1.
4 - 8 4 INSTALLATION AND W IRING 4.2.2 SSC I/F communi cation cable (1) Precauti ons for handling the SSC I/F communication cable • Do not stam p the SSC I/F com munic ation ca ble. • W hen layin g the SSC I/F c omm unicat ion ca ble, b e sur e to sec ure th e m inimum cable bend r adius of 30 mm (1.
4 - 9 4 INSTALLATION AND W IRING 4.2.3 Battery cabl e (1) Precauti ons for handling the batter y cable • For i nstal lation or r em oval of the b atter y cab le, ho ld su rel y a cab le con nector .
4 - 10 4 INSTALLATION AND W IRING 4.2.4 Cable for teaching uni t (1) Precauti ons for handling the cable for teaching unit • Do no t stamp the cable fo r tea ching unit. • W hen layin g the c ab le for t each ing un it, be sure to s ecure the m inim um cable bend r adius of 30 m m (1.
4 - 11 4 INSTALLATION AND W IRING ! CAUTION W hen a teac hing unit is re moved, the emer genc y stop an d ser vom otor bec ome c oasti ng sta te. I n system s wher e coas ting of t he ser vom otor wi ll be a prob lem, use d ynam ic brak es.
4 - 12 4 INSTALLATION AND W IRING 4.3 Installation o f the Serial Absolute Sy nchronous Encoder This sect ion des cri bed ins truc tions for h andl ing th e Ser ial a bso lute s ynchr onous encoder (MR-HENC /Q170ENC).
4 - 13 4 INSTALLATION AND W IRING ! CAUTION The M R-HENC /Q1 70EN C cont ains a glas s disk and precis io n mec hanism . T ake car e when hand ling it. T he enco der p erf orm ance m ay deter iora te if it is dro pped or subj ected to s hock s or v ibrat ion excee ding t he prescr ibed l im its.
4 - 14 4 INSTALLATION AND W IRING 4.4 Replacement of the Cooli ng fan unit (Q170 FAN) (Q173CPU /Q172CPU only) (1) Remov al and installation of the cooling fan unit ( Q170FAN) (a) Rem oval of co oling f an unit fr om Q 173CPU/Q 172C PU The re mova l of the co oling fan unit are d escr ibed belo w.
4 - 15 4 INSTALLATION AND W IRING 4.5 W iring 4.5.1 Instructions for w i ring ! DANGER Comple tel y turn off th e al l lines of th e po wer supp l y externa ll y before wiri ng. N ot co mp letel y turnin g off all po wer c ould r esult in el ectr ic sh ock or dam age to the product.
4 - 16 4 INSTALLATION AND W IRING (b) Do not bunch or la y the m closel y the m ain c ircuit (hi gh vol tage, large curren t) cables of the 100 VAC and 24 VDC wit h the I/O sig nal cab les. If possib le, se parate them 100m m (3.94inch) or m ore awa y.
4 - 17 4 INSTALLATION AND W IRING (g) W iring of 200m (65 6.17f t.) or m ore d istanc e wi ll gi ve ris e to le akage curre nts due t o the wiring ca pacit y, res ultin g in a fa ult. Refe r to the troub lesho oting ch apter of th e I/O Modu le User 's Manua l.
4 - 18 4 INSTALLATION AND W IRING 4.5.2 Wiring to the power supply module The f ollowi ng d iagram sho ws the wiring exam ple of pow er li nes, gr ound ing lines , etc . to th e CPU a nd ex tens ion base units. AC 100/110VAC Fuse 24VDC AC DC Connect to 24VDC te rminals of I/O module that requires 24VDC internally.
4 - 19 4 INSTALLATION AND W IRING 4.6 Installation/ W iri ng Checkli st At the work site, c opy t he fol lowin g tab le for us e as a che ck sheet. Item Sub Item Installation/wiring confir mation Check Check for looseness, rattl ing or distorted inst allation.
4 - 20 4 INSTALLATION AND W IRING At the worksi te, copy the following table for u s e as a check sh eet . (Conti nued) Item Sub Item Installation/wiring confir mation Check When using Q173DV, check th at the Q173CPU(N) and Q173DV are connected to the SSCNE T cable.
5 - 1 5 TRIAL OPERATION AND ADJUSTMENT 5. TRIAL OPERATION AND ADJUSTMENT 5.1 Checklist before T rial Oper ation Table 5.1 Checkl ists before Trial Operation Model nam e Confirm ation It ems Reference (1) Check t hat the batt ery lead con nector is connected i nto the BAT connector of the Dividing u nit correc tly.
5 - 2 5 TRIAL OPERATION AND ADJUSTMENT 5.2 Trial Operati on and Adjustment Proced ure Be sure to ground the Motion con trollers, s ervo amp lifie rs and se rvomot ors. (Ground r esistance: 1 00 or les s) Do not g round comm only with other devices. Set the followi ng positioning parameters from the peripher al devise.
5 - 3 5 TRIAL OPERATION AND ADJUSTMENT 2) Motion CPU CAUTION [Servo data setting mod e] CAUTI ON Check external in puts to Q172LX Check the w iring of fol lowing exte rnal inputs b y monitori ng of the p eriphera l device.
5 - 4 5 TRIAL OPERATION AND ADJUSTMENT Turn ON again the po wer supply or reset of Multiple CPU system. Crea te Moti on pro grams Write PLC p rograms Motion CPU [Programming mode] Create the Mo tion prog rams by GSV P .
5 - 5 5 TRIAL OPERATION AND ADJUSTMENT Check servo a mplifier Chec k t hat the i nsta lle d s ervo ampl ifiers ope rat e corr ectly. CAUTION Motio n CPU 3) 4) [Test mode servo sta rt-up (Initial check.
5 - 6 5 TRIAL OPERATION AND ADJUSTMENT [Progr amming mo de] End PLC CP U Motion CPU Check by aut omatic oper ation Check the sequence oper ation by exe cuting the PLC pr ogram usi ng an actual exte rnal inp ut.
5 - 7 5 TRIAL OPERATION AND ADJUSTMENT 5.3 Operating Sy stem Sof twar e Installation Procedur e The op erati ng s ystem softwar e mus t be ins ta lled t o the Moti on CPU m odu le b y usin g the per ipher al de vice a nd pr ogram m ing soft ware pac ka ge.
5 - 8 5 TRIAL OPERATION AND ADJUSTMENT 5.4 Trial Operati on and Adjustment Checkli st At the work site, c opy t he fol lowin g tab le for us e as a che ck sheet. Work Step I tem Trial Operation and Adjus tm ent Confirmat ion Ch eck Check t hat the each m odule is installed c orrectly.
6 - 1 6 INSPECTION AND M AINTENANCE 6. INSPECTION AND MAINTENANCE ! DANGER Do not touc h the t erm inals while power is on. Doi ng so could c ause e lectr ic shoc k. Correctly connect the ba tter y. Als o, do not c harge, dis assem ble, h eat, place i n fire , short c ircu it, or solder th e batter y.
6 - 2 6 INSPECTION AND M AINTENANCE 6.1 Maintenance W orks 6.1.1 Instruction of inspecti on works In order that can us e the Moti on contr oller in safet y and norm al, th ose item s that m ust be inspec ted lis t belo w.
6 - 3 6 INSPECTION AND M AINTENANCE ! CAUTION Do not s hort circu it, ch arge, over heat, i nciner ate or disa ssem ble t he batt eries . The e lectro l ytic capac it or will gen erate gas dur ing a faul t, so d o not plac e your f ace near the M otio n contr oller or ser vo am plifi er.
6 - 4 6 INSPECTION AND M AINTENANCE 6.2 Daily Inspecti on The it em s that m ust be insp ecte d dail y ar e list ed b elow. Table 6.1 Daily Inspection Item Inspection item Inspection Criterion Action 1 Installation of the base unit Check that the fix ing screws are not loose and the cover is not dislocated.
6 - 5 6 INSPECTION AND M AINTENANCE Daily Inspecti on(continued) Item Inspection item Inspection Criterion Action Input LED Check that the LED is ON/OFF. The LED must be ON at input signal ON. The LED must be OFF at input signal O FF. (Abnormal if the LED does not turn ON or turn OFF as indicated abov e.
6 - 6 6 INSPECTION AND M AINTENANCE 6.3 Periodic Inspecti on The it em s that m ust be insp ected one or two t im es ever y 6 m onths to 1 year ar e list ed below. W hen the e quipm ent is mov ed or m od ified, or la yout of the wiri ng is c ha nged, also im plement t his insp ecti on.
6 - 7 6 INSPECTION AND M AINTENANCE 6.4 External Battery The s pecia l rela ys (M 9006, M900 7) tur n ON due t o the Motion CPU progr am or the decre ase in vo ltage of memor y back -up batt er y. Even if th ese spec ia l rela ys tur n ON, the progr am an d th e cont ents of m emor y back -up are not er ased im m ediatel y.
6 - 8 6 INSPECTION AND M AINTENANCE 6.4.1 Battery serv ice life time (1) Q173CPU (N)/Q172CPU( N), Q172EX module batter y service l if e time The batt ery ser vice l ife tim e corresp onding to the t ype is sho wn below.
6 - 9 6 INSPECTION AND M AINTENANCE 6.4.2 Battery r eplacement procedure (1) Q172EX module battery replacement pro cedure W hen the Q172EX module bat ter y has been ex hauste d, repl ace the bat ter y with a new one i n acc ordance wi th the pr oce dure sh own b elo w.
6 - 10 6 INSPECTION AND M AINTENANCE (2) Battery replacement procedur e of the Div iding unit, Battery unit W hen the ba tter y has b een ex haust ed, re place the ba tter y with a ne w one in accord ance with t he pr oced ure s hown belo w. POINTS Replac e the b atter y tak ing c are of the f ollo wing.
6 - 11 6 INSPECTION AND M AINTENANCE 6.5 Discard of internal rechargeabl e battery (1) Discard pr ocedure of internal recharg eable battery The rech argea ble lith ium batter y is built- in in the M otio n CPU m odule.
6 - 12 6 INSPECTION AND M AINTENANCE ! CAUTION Do not disassemble the modules except the t ime of discard. Do not short circuit, charge, overheat, incinerate or disassemble the batt eries.
6 - 13 6 INSPECTION AND M AINTENANCE 6.6 Troubleshooti ng This sect ion des cribes th e vari ous t ypes of trou ble t hat oc cur when th e s ystem is operat ed, an d ca uses an d cor rect ive act ions of thes e tro ubles.
6 - 14 6 INSPECTION AND M AINTENANCE 6.6.2 Troubleshooti ng of Motion CPU mo dule and I/O modules This sectio n des cribes the c ont ents of trou bles f or th e error codes and c orr ective actions of t he tro ubles .
6 - 15 6 INSPECTION AND M AINTENANCE (a) Flowchart for w hen "POW ER" LED is turned o ff. The fo llowin g shows the flow chart when the "PO W ER" LED is tur ned off a t the po wer su ppl y ON or duri ng oper ation . "POWER" LED is turned off Explain the error symptom and get advice from our sal es representative.
6 - 16 6 INSPECTION AND M AINTENANCE (b) Flowchart for w hen "MODE" LED is turned o ff. The fo llowin g shows the flow chart when the "MODE" LED is tu r ned o ff at the po wer su ppl y ON. "MODE" LED is turned off Che ck the w iri ng and t urn on t he all power supplies.
6 - 17 6 INSPECTION AND M AINTENANCE (c) Flowchar t for when "RUN" LED is turned off. The fo llowin g shows th e flow c har t when th e "RUN" LED i s turned off du ring operat ion. "RUN" LED is t urned off. Is "E RR.
6 - 18 6 INSPECTION AND M AINTENANCE (d) Flowchart for w hen "ERR." LED is turned on/ flickered. The fo llowin g shows the flow chart to be follow ed when the "ERR." LED is turned on/flick ered at th e power su ppl y ON or operat ion star t or durin g operat ion.
6 - 19 6 INSPECTION AND M AINTENANCE (e) Flowchart for when "M.RUN" LED is turned off. The fo llowin g shows the flow chart when the "M.R UN" LED i s turned off durin g op eratio n. "M.RUN" LED is turne d off. Completi on NO YES NO YES Set th e RESET/L.
6 - 20 6 INSPECTION AND M AINTENANCE (f) Flowchart for w hen "BAT." LED is turned o n. In the M otio n CPU, when th e exter nal b atter y capac ity o f the Di viding unit or Bat ter y unit is l owered , th e LED is tur ned on. After r eplac ing t he b atter y with a ne w one, "BAT .
6 - 21 6 INSPECTION AND M AINTENANCE (g) Flowchart for w h en output load of output module is not turne d on. The fo llowin g shows the flow chart when the outp ut load o f the ou tput module is not tur ned on dur ing opera tion. Voltage measurement among the modules input and COM terminals.
6 - 22 6 INSPECTION AND M AINTENANCE (h) Flowchart for w h en the peripheral dev ice cannot communicate to the Motion controll er. The fo llowin g shows the flow chart when the Moti on CPU cannot commun ica te with th e GSV P durin g the po wer su ppl y ON.
6 - 23 6 INSPECTION AND M AINTENANCE Is t he c ommun icati on setting correct? 1) NO YES YES NO Com plet ion NO Expl ain the erro r sympto m and ge t advice from our sale s repres entativ e. YES Explain the erro r sy mptom a nd get adv ice from our sales r eprese ntative.
6 - 24 6 INSPECTION AND M AINTENANCE (i) Flow chart for when the power supply of teaching unit is not turned on. The fo llowin g shows the flow chart when the powe r supply of teac hing uni t is not tur ned on dur ing the p ower sup pl y of Mot ion CPU O N.
6 - 25 6 INSPECTION AND M AINTENANCE 6.6.3 I/O modules tr oubleshooting This sect ion des cribes tro ubles hoot ing wit h I/O circ uits and their correc tiv e acti ons. (1) Input cir cuit troubleshooting and corrective action This sect ion des cri bes tro ubles hoot ing with input c ircui ts an d th eir c orrect ive actions .
6 - 26 6 INSPECTION AND M AINTENANCE Input Circ uit Troubleshooting and Correctiv e Action (Continued) Condition Cause Corrective action Example 5 Input signal does not turn OFF. • Sneak path due to the use of t wo power supplies. Input module E 1 E 2 > E 2 E 1 • Use only one pow er supply.
6 - 27 6 INSPECTION AND M AINTENANCE (2) Output cir cuit troubleshooting and cor rective acti on This se ction describ es troubl eshooting with ou tput cir cuits and their corre ctive actions .
6 - 28 6 INSPECTION AND M AINTENANCE 6.7 Confir m method of Er ror Code W hen an err or occ urs, the er ror cod e and error m ess age ca n be r ead b y the person al com puter(I BM PC/ AT) insta llati on of t he SW 6RN- GSV P. The proc ed ure f or re ading err or cod es b y the SW 6RN-GSV P is as f ollo ws.
App - 1 A PPENDICES APPENDICES APPENDIX 1 Cab les In this cabl e con nectio n dia gram , m aker nam es of conn ectors are om itte d. Ref er to "APPEND IX 2.7 Conn ector" for m aker nam es of connec tors. APPENDIX 1.1 SSCNET cables Gener ally use the SS CNET cable s avai lable as our optio ns.
App - 2 A PPENDICES Use th e followin g or equiv alent twi sted pair cables a s the SSCNE T cable s. Table 2 W ire models Type Length [m(ft.)] W ire model Q172J2BCBL M(-B) Q172HBCBL M(-B) 0.5(1.64), 1(3.28), 5(16.40) UL20276 AWG#28 7pair(CREAM) Q173DVCBL M 0.
App - 3 A PPENDICES (a) Q172J2BCBL M(-B) 1) Model ex planation Type: Q172J 2BCBL M- None Connect Battery u nit B No 05 Cable length [m(ft.)] 1 Symbol 5 0.5(1.64) 1(3.2 8) 5(16.40) Symbol Yes 2) Connection di agram W hen fabric ati ng a c able, use t he rec omm ended wire gi ven on APPENDIX 1.
App - 4 A PPENDICES (b) Q172HBC BL M(-B ) 1) Model ex planation None Connect Battery u nit B No 05 Cable length [m(ft.)] 1 Symbol 5 0.5(1.64) 1(3.28) 5(16.40) Type: Q172HBCBL M- Symbol Yes 2) Connection di agram W hen fabric ati ng a c able, use t he rec omm ended wire gi ven on APPEND IX 1.
App - 5 A PPENDICES (c) Q173DVC BL M 1) Model ex planation Type: Q173DVCBL M 05 Cable length [m(ft.)] 1 Symbol 0.5(1.64) 1(3.28) 2) Connection di agram W hen fabric ati ng a c able, use t he rec omm ended wire gi ven on APPEND IX 1.1 , and m ak e the cab le as s how in th e fo llowi ng connec tion diagr am .
App - 6 A PPENDICES (d) Q173J2B CBL M 1) Model ex planation none Symbol Number of SSCNET SYSTEM SSCNET SY STEM 1 SSC N ET SY STEM 2 2 3 4 05 Cable length [m(ft.
App - 7 A PPENDICES (e) Q173HB CBL M 1) Model ex planation none Symb ol Numb er of SSCNET SYST EM SSCN ET SYSTEM 1 SSCNET SY STEM 2 2 3 4 05 Cable length [m(ft.
App - 8 A PPENDICES (f) MR-J2 HBUS M 1) Model ex planation 05 Cable length [m(ft.)] 1 Symbol 5 0.5(1.64) 1(3.28) 5(16.40) Type: MR-J2HBUS M 2) Connection di agram W hen fabric ati ng a c able, use t he rec omm ended wire gi ven on APPENDIX 1.1 , and m ak e the cab le as s how in th e foll owi ng connec tion diagr am .
App - 9 A PPENDICES (g) MR-J2 HBUS M-A 1) Model ex planation 05 1 5 0.5(1.64) 1(3.28) 5(16.40) Symbol Type: MR-J2HBUS M-A Cable length [m(ft.)] 2) Connection di agram W hen fabric ati ng a c able , use t he rec omm ended wire gi ven on APPENDIX 1.1 , and m ak e the cab le as s how in th e foll owi ng connec tion diagr am .
App - 10 A PPENDICES (h) MR-HB US M 1) Model ex planation 05 1 Symbol 5 0.5(1.64) 1(3.28) 5( 16.4 0) Type: M R-HBU S M Cable length [m(ft.)] 2) Connection di agram W hen fabric ati ng a c able, use t he rec omm ended wire gi ven on APPENDIX 1.1 , and m ak e the cab le as s how in th e foll owi ng connec tion diagr am .
App - 11 A PPENDICES APPENDIX 1.2 Ser ial a bsolute synchr onous encoder cable Gener all y use t he ser ial a bsolu te s ynchron ous e ncod er cab les a vailab le as our options . If the r equir ed len gth is not f oun d in o ur opt ions , fabr icate the c abl e on th e custo mer side.
App - 12 A PPENDICES (2) MR-JHS CBL M-L/H Synchr onous encod er c able is t he s ame e ncoder cab les of the HC- SFS/HC- RFS/HC-U FS 2 000 r/m in s eries s ervom otors . (a) Model explanation Symbol L H 2 Cable length [m(ft.)] 5 Symbol 10 20 30 2(6.56) 5(16.
App - 13 A PPENDICES (3) Q170ENCCBL M (a) Model explanation Type: Q170ENCCBL M 2 Cable length [m(ft.)] 5 Symbol 10 20 30 2(6.56) 5(16.40) 10(32.81) 20(65.62) 30(98.43) 50 50(164.04) (b) Connecti on diagr am W hen fabric ati ng a c able, u se t he recom m ended wir e a nd c onnect or s et Q170 ENCCNS for encod er cabl e given on APPE NDIX 1.
App - 14 A PPENDICES APPENDIX 1.3 Cable for the teaching uni t Gener all y use t he cab les f or the t eachi ng u nit av ailab le as o ur opt ions. If th e req uire d length is not fou nd i n our options , fabr icat e the cabl e on the cust om er sid e.
App - 15 A PPENDICES Table 9 W ire speci f ications Characteristics of one core Wire model Core size [mm 2 ] Number of cores Structure [Number of wires/mm] Conductor resistance [ /km] Insulating sheath OD d[mm] (Note-1) Finished OD [mm] (Note-2) UL20276 A W G#28 13p air(CREAM) 0.
App - 16 A PPENDICES (2) Q170TUD3C BL3M (a) Connecti on diagram W hen fabric ating a c able, u se the r ecom m ended wir e a nd c onnect or give n on APPEN DIX 1.3, and m ake th e cabl e as show in th e foll owing connec tion diagr am. Mak e the c able wit hin 3m (9.
App - 17 A PPENDICES (3) Q170TUDNCBL3M (a) Connecti on diagram W hen fabric ating a c able, u se the r ecom m ended wir e a nd c onnect or give n on APPEN DIX 1.3, and m ake th e cabl e as show in th e foll owing connec tion diagr am. Mak e the c able wit hin 3m (9.
App - 18 A PPENDICES (4) Q170TUDNCBL03M-A (a) Connecti on diagram W hen fabric ating a c able, u se the r ecom m ended wir e a nd c onnect or give n on APPEN DIX 1.3, and m ake th e cabl e as show in th e foll owing connec tion diagr am. Mak e the c able wit hin 3m (9.
App - 19 A PPENDICES (5) A31 TU-D extended cabl e (a) Connecti on diagram W hen fabric ating a c able, u se the r ecom m ended wir e a nd c onnect or gi ven on AP PENDIX 1.3, an d m ake the cabl e as s how in the f ollo wing c onn ectio n diagr am. T he cab le over all distanc e bet ween the Mo tio n CPU a nd te aching unit is with in 3 0m ( 98.
App - 20 A PPENDICES APPENDIX 2 Ex terior Dimensions APPENDIX 2.1 CPU module (1) Q172CPU N Module [Unit: m m ( inch)] 114.3(4.50) 17.5 79.5(3.13) (0.69) SSCNET M.RU N Q172CPUN MODE RUN ERR . BAT. BOOT FRONT CN2 CN1 PULL USB RS-232 27.4(1.08) 98(3.86) (2) Q173CPU N Module [Unit: m m ( inch)] Q173CPUN SSCNET M.
App - 21 A PPENDICES (3) Q172CPU N-T Module [Unit: m m ( inch)] 114.3(4.50) 17.5(0.69) 79.5(3.13) 46(1.81) SSCNET M.RUN Q172CPUN-T MODE RUN ERR. BAT. BOOT FRONT CN2 CN1 PULL USB RS-232 27.4(1.08) 98(3.86) TU (4) Q173CPU N-T Module [Unit: m m ( inch)] Q173CPUN-T SSCNET M.
App - 22 A PPENDICES (5) Q172CPU Module [Unit: m m ( inch)] 48.5(1.91) 17.5 89.3(3.52) SSCNET M.RUN Q172C PU MODE RUN ERR . BAT. BOOT FRONT CN2 CN1 PULL USB RS-232 27.4(1.08) 98( 3.86 ) 20 26(1.02) (0.69) (0.79) Cooling fan uni t (6) Q173CPU Module [Unit: m m ( inch)] 89.
App - 23 A PPENDICES (7) Q173CPU N(-T)/Q172CPUN (-T) Modul e (with SSCNET cable) [Unit: m m ( inch)] 98(3. 86) 100(3.9 4) Q173C PUN SSCNET M.RU N MODE RUN ERR.
App - 24 A PPENDICES APPENDIX 2.2 Servo exter nal signals inter face module (Q172LX ) [Unit: m m ( inch)] Q172L X CTRL Q172LX 98(3.86) 27.4(1.08) 90(3.54) 45(1.77) APPENDIX 2.3 Serial absolute synchr onous encoder interface modul e (Q172EX/Q172EX -S1/ Q172EX- S2/Q172EX-S3) [Unit: m m ( inch)] 4.
App - 25 A PPENDICES APPENDIX 2.4 Manual pulse gener ator interface module (Q173PX /Q173PX-S1) (1) Q173PX [Unit: m m ( inch)] Q173PX PULSER Q173PX PLS.A 3 2 1 PLS. B 3 2 1 TREN 3 2 1 98( 3.86 ) 27.4 (1.08 ) 90(3.54) 45 (1. 77 ) (2) Q173PX -S1 [Unit: m m ( inch)] Q173P X PULSER Q173PX-S1 PLS.
App - 26 A PPENDICES APPENDIX 2.5 Power supply module ( Q61P-A1, Q61P-A2, Q62P, Q63P, Q64P) [Unit: m m ( inch)] (1) Q61P-A1, Q61P- A2, Q62P, Q63P Q61P -A1 POWER PULL 90(3.54) 55.2(2.17) 98(3.86) (2) Q64 P [Unit: m m ( inch)] Q64P POWER PUL L 115(4.53) 55.
App - 27 A PPENDICES APPENDIX 2.6 Dividing unit (Q173D V), Battery uni t (Q170BAT) (1) Dividing uni t (Q173DV) [Unit: m m ( inch)] BAT Q173CPU SSCNET CN2 SSCNET CN1 SSCNET CN4 SSCNET CN3 Q17 3D V DATE PASSED 125(4.92) 19.5 (0.77) 10 (0.39) 45(1.77) 60(2.
App - 28 A PPENDICES APPENDIX 2.7 Connector (1) Honda connectors make(HDR model) (Cable connector for the teaching uni t) Type Number of pins Connector Connector case 14 HDR-E14MG1 HDR-E14LPA5 HDR-E26MG1 26 HDR-E26 FG1 HDR-E26LPA5 Spec ified t ool: FHAT-00 29/FHP T -000 4C Make r: Ho nda conne cto rs Thes e tools are not so ld in Mitsub ishi.
App - 29 A PPENDICES (2) Sum itom o 3M m ake(MDR t ype) (Cable connector for the serial absol ute synchronous encoder) Type Number of pins Type Connector Connector case Solder connection type (Quick r.
App - 30 A PPENDICES (b) Solder connection type( Threaded type) Type Conne cto r : 10120- 3000VE /10126-30 00VE Connec tor c ase: 1 0320- 52A0- 008/10 326-5 2A0- 008 [Unit: m m ( inch)] 1 0 . 0 ( 0 . 3 9 ) 12.0 (0.4 7) A 3 9 . 0 ( 1 . 5 4 ) 2 3 . 8 ( 0 .
App - 31 A PPENDICES (4) Q170TUD3C BL(A31TU-D3 side connector) T ype Connect or : D B-25SF -N (Mak er : J apan Aviat ion Elec tron ics Industr y) Scre w lock : D2 0418- J3 (M aker : J apan Aviat i.
App - 32 A PPENDICES (6) A31 TUD3T M T y pe Connec tor : 1 7JE- 23250- 02(D8 A) (Mak er : DDK) [Unit: m m ( inch)] 35.0(1.38) 1 5 . 0 A31TUD3TM 1 9 . 0 1 9 . 0 6 . 1 54.0(2.13) Cabl e outsi de diam eter 9(0 .35) o r les s ( 0 . 5 9 ) ( 0 . 2 4 ) ( 0 .
App - 33 A PPENDICES APPENDIX 2.8 Manual pulse gener ator (MR-HD P01) [Unit: m m ( inch)] (0.63) Packing 27.0 20 8.89 0 . 2 7 2 ( 2 . 8 3 ) 3.6(0.14) t =2.0 3 Studs (M4 10) PCD72, M3 6 7.6 16 0. 70(2.76) 50(1.97) 60(2.36) 0.5 8 0(3.15) 1 NP 5 to 12V 0V A B equi-spaced 6 2 ( 2 .
App - 34 A PPENDICES APPENDIX 2.9 Serial absolute synchr onous encoder (MR-H ENC/Q170ENC) (1) MR-HE NC [Unit: m m ( inch)] 0 -0.11 -0.006 -0.017 0 -0.11 -0.009 -0.025 +0.1 4 -0.012 -0.042 +0.1 0 5(0.20) 3(0.12) Shaft cross-section B 50(1.97) 15(0.59) 14.
App - 35 A PPENDICES APPENDIX 2.10 Teaching unit ( A31TU-D3 /A31T U-DN ) [Unit: m m ( inch)] <Side fa ce> <Back face> <Front fac e> A31TU DISABLE EMG.
App - 36 A PPENDICES APPENDIX 2.11 Cooling fan unit (Q170FAN) (Q173CPU/Q172C PU only) [Unit: m m ( inch)] 25 25 0.5 10 0.5 8 2 3 6 1 18 (0.98) (0.98 0.
App - 37 A PPENDICES MEM O.
WA RRA NT Y Please confir m the following product w arranty details bef ore using th is product. 1. Gratis W arranty Term and Gratis W arranty Rang e If any faults or defects ( hereinafter "Failu.
IB(NA)-0300040-D(0603)MEE MOTION CONTROLLER Qseries (Q173CPU ( N ) /Q172CPU ( N )) User's Manual U Q MOTION CONTROLLERS Q173CPU ( N ) Q172CPU ( N ) User's Manual MODEL MODEL CODE Q173-U-E 1X.
Ein wichtiger Punkt beim Kauf des Geräts Mitsubishi Electronics Q173CPU(N) (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Mitsubishi Electronics Q173CPU(N) noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Mitsubishi Electronics Q173CPU(N) - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Mitsubishi Electronics Q173CPU(N) reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Mitsubishi Electronics Q173CPU(N) erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Mitsubishi Electronics Q173CPU(N) besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Mitsubishi Electronics Q173CPU(N) verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Mitsubishi Electronics Q173CPU(N). Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Mitsubishi Electronics Q173CPU(N) gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
