Benutzeranleitung / Produktwartung HC7000 des Produzenten Mitsubishi Electronics
Zur Seite of 47
LCD PROJECTOR This User Manual is important to you. Please r ead it befor e using your pr ojector . MODEL HC7000 User Manual HC7000.
EN-2 The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literatur e accompanying the appliance.
EN-3 Note: This symbol mark is for EU countries only . This symbol mark is according to the dir ective 2002/96/EC Article 10 Information for users and Annex IV , and/or to the directive 2006/66/EC Article 20 Information for end-users and Annex II.
EN-4 Please read all these instructions r egar ding your projector and r etain them for futur e refer ence. Follow all warnings and instructions marked on the projector . Read instructions All the safety and operating instructions should be read befor e the appliance is operated.
EN-5 WARNING: Unplug immediately if there is something wr ong with your projector . Do not operate if smoke, strange noise or odor comes out of your projector . It might cause fi re or electric shock. In this case, unplug immediately and contact your dealer .
EN-6 2 3 Checking accessories The following accessories are pr ovided with this pr ojector . Check to be sure that all of the accessories ar e packed in the package. Cables Mini D-SUB 15-pin Mini D-SUB 15-pin D-SUB 9-pin D-SUB 9-pin RGB cable for PC (246C521-10) RS-232C cable (246C548-10) Used for projector contr ol by computer .
EN-7 Overview VIDEO IN and S-VIDEO IN terminals COMPONENT VIDEO IN terminals COMPUTER IN/COMPONENT VIDEO IN terminal (mini D-SUB 15-pin) HDMI IN-1 terminal (HDMI 19-pin) HDMI IN-2 terminal (HDMI 19-pin) SERIAL terminal (D-SUB 9-pin) Used for projector contr ol by computer .
EN-8 Remote contr ol ON ( I ) button HDMI2 button HDMI1 button COMPONENT button A V MEMOR Y buttons ENTER button MENU button CONTRAST button* BRIGHTNESS button* GAMMA button* ZOOM/FOCUS button LENS SHIFT button NOISE REDUCTION button* COLOR button* SHARPNESS button* COLOR TEMP .
EN-9 30° 30° 30° 30° Operational range of the r emote contr ol V ertical directions (ceiling mount) Reception angle V ertical directions When operating the remote contr ol, keep the distance from the r emote contr ol to the projector via the scr een within about 5 m (15 feet).
EN-10 Setting up your pr ojector Setting up the scr een Install the screen perpendicularly to the pr ojector . If the screen can not be installed in such a way , adjust the projection angle of the pr ojector .
EN-11 Setting up your pr ojector (continued) Scr een size and pr ojection distance (continued) Screen width (SW) Down side Up side 50% 50% Screen Screen height (SH) H1 H1 L Right side Left side W1 W1 .
EN-12 Adjusting the position of the pr ojected image T o adjust the position of the projected image on the screen, use the LENS SHIFT button. Press the LENS SHIFT button. The LENS SHIFT menu appears at the center of the screen. Press the S , T , W or X button to move the image position.
EN-13 Fr ont pr ojection, ceiling mounting For ceiling mounting, you need the ceiling mount kit designed for this projector . Ask a specialist for installation.
EN-14 DVD player A. Connecting the pr ojector to video equipment When the projector and the connected devices ar e located too close to each other , the projected image may be affected by their interfer ence. See the owner’ s guide of each device for details about its connections.
EN-15 1 2 1 2 Connect one end of the optional video cable to the VIDEO IN terminal of the projector . Connect the other end of the video cable to the video output terminal of the video equipment. 1. 2. Also read the instruction manual of the equipment to be connected.
EN-16 Connecting to video equipment having a HDMI terminal Y ou can project high-quality images by connecting the HDMI IN terminal of this projector to video equipment having a HDMI output terminal. In addition, this projector supports HDCP and is able to r eceive encrypted digital video data that are output fr om DVD players.
EN-17 B. Plugging in the power cor d In order to ensur e the safety in case of trouble with the projector , use an electrical outlet having an earth leakage breaker to supply the power to the pr ojector . If you do not have such outlet, ask your dealer to install it.
EN-18 Confi rm the POWER indicator lights-up r ed. If the projector was turned off befor e the lamp had cooled down suffi ciently , the fan may start rotating and the POWER button may not work after the power cord is plugged. (The ST A TUS indicator blinks green.
EN-19 Press the POWER button on the pr ojector or the OFF ( ) button on the remote contr ol. A confi rmation message is displayed. T o cancel the procedure, leave the pr ojector for a while or press the MENU button. Press the POWER button on the pr ojector or the OFF ( ) button on the remote contr ol again.
EN-20 Viewing video images (continued) Setting the aspect ratio Y ou can change the aspect ratio of the input video signal (or the ratio of width to height of the image).
EN-21 How to change the settings: With the remote contr ol: Press the ASPECT button. Every time the ASPECT button is pressed, the aspect mode changes fr om AUTO to 4:3, 16:9, to ZOOM1, to ZOOM2, to STRETCH, to ANAMORPHIC1, to ANAMORPHIC2, and back to AUTO.
EN-22 2 1 A. Connecting the pr ojector to a computer Preparation: Make sure that the power of the pr ojector and that of the computer are turned off. When connecting the projector to a desktop computer , disconnect the RGB cables that are connected to the monitor .
EN-23 Confi rm the POWER indicator lights-up r ed. If the projector was turned off befor e the lamp had cooled down suffi ciently , the fan may start rotating and the POWER button may not work after the power cord is plugged. (The ST A TUS indicator blinks green.
EN-24 Viewing computer images (continued) Press the LENS SHIFT button. The LENS SHIFT menu appears at the center of the scr een. Press the S or T button to adjust the vertical position and W or X button to adjust the horizontal position of the displayed image.
EN-25 Menu operation Menus are not displayed when no signal is supplied to the pr ojector . IMAGE GAMMA MODE AUTO, SPORTS, VIDEO, CINEMA USER1 REFERENCE SPORTS, VIDEO, CINEMA USER2 ADJUST MODE ALL, RED, GREEN, BLUE CONTRAST ±30 HIGH ±10(R) ±10(G) ±10(B) BRIGHTNESS ±30 MID ±10(R) ±10(G) ±10(B) COLOR TEMP .
EN-26 How to set the menus: The following describes how to set AUTO POWER OFF time as an example. Press the MENU button. IMAGE opt. A V MEMORY 1 Press the W or X button to select a menu to use. INS T ALL A TION opt. A V MEMO R Y 1 Press the ENTER button (or T button).
EN-27 2. INST ALLA TION menu ITEM SETTING FUNCTION KEYSTONE ±15 Use to corr ect vertical keystone distortion. LAMP MODE ST ANDARD Select this option when you want to view images in a well-lit room. LOW Select to moderate the intensity of the lamp. The fan operating sound is reduced and the lamp lifetime becomes longer .
EN-28 3. FEA TURE menu FE A TURE AUTO AUTO AUTO opt. MENU POSITION CINEMA MODE VIDEO SIGNAL ? ASPECT RESET ALL English LANGUAGE A Ë OFF AUTO OK DISPLA Y INPUT P ASSWORD FUNCTION 1. MENU DIMMER A V MEMO R Y 1 SETUP SCART INPUT OFF Menu operation (continued) 3.
EN-29 4. SIGNAL menu 5. USER menu R G B R G B SIGNAL HORIZ. POSITION 0 VERT . POSITION 0 TRACKING 0 COMPUTER INPUT AUTO FINE SYNC. 0 USER opt. OK ON HOLD 100% OVER SCAN A V MEMO R Y 1 CLAMP POSITION USER 1 CLAMP WIDTH 1 LPF OFF SHUTTER(U) 0 SHUTTER(L) 0 VERT .
EN-30 6. INFORMA TION menu Menu operation (continued) INFORMA TION opt. LAMP TIME(LOW) INPUT RESOLUTION VERTICAL FREQUENCY HORIZONT AL FREQUENCY SYNC. TYPE 5wir e 60.
EN-31 T o adjust the brightness (CONTRAST and BRIGHTNESS): Y ou can make adjustments for the brightness of the projected image using the menu. (See page 26 for menu setting.) Display the IMAGE menu. Select CONTRAST or BRIGHTNESS by pressing the S or T button.
EN-32 T o adjust the tone of white (COLOR TEMP .): Y ou can select a preset color temperature (white tone) using the menu. (See page 26 for menu setting.) Display the IMAGE menu. Select COLOR TEMP . by pressing the S or T button. Select your desired color temperatur e by pressing the W or X button.
EN-33 Adjusting pr ojected images (continued) T o adjust the ratio of change in brightness (GAMMA MODE): Y ou can select a preset gamma mode using the menu. (See page 26 for menu setting.) Display the IMAGE menu. Select GAMMA MODE by pressing the S or T button.
EN-34 This projector automatically and pr operly projects video signals supplied from the computer . However , some video signals may not be projected, depending on the type of the computer . In such a case, press the AUTO POSITION button. (See page 24.
EN-35 Password function This projector is equipped with the passwor d function that is designed for prevention of theft and wr ong operation by children and r estriction on operation by other than specifi ed users. The passwor d function has two modes as follows.
EN-36 This projector is equipped with a lamp to pr oject images. This lamp is a consumable. It may bur n out or its brightness may decrease during use. In such cases, r eplace the lamp with a new one as soon as possible. Be sure to replace the lamp with a new lamp sold separately that is exclusive to this projector .
EN-37 Replacing the lamp (continued) T o replace the lamp: Unplug the power cord. Loosen two screws (a) using a Phillips scr ewdriver (+) and remove the left side panel fr om the projector . (a) Loosen the screw (b) using a Phillips scr ewdriver (+), and remove the lamp cover (c).
EN-38 When removing the lamp fr om the ceiling-mounted projector When removing the lamp fr om the ceiling-mounted projector , use the lamp replacement tray packed with the projector or option lamp to pr event glass fragments from scattering. Assemble the lamp replacement tray accor ding to the procedure shown on it.
EN-39 W ar ning: Never use fl ammable air duster or other materials when cleaning the air -fi lter . Flammable substances may ignite causing fi r e or breakdown when the lamp is illuminated. Do not use fl ammable solvents (benzene, thinner , etc.) and fl ammable aerosols when cleaning the pr ojector body and lens.
EN-40 Before asking for r epair of the projector , check the following. If the symptom persists, stop using the projector , be sure to unplug the power plug, and then contact your dealer . No image appears on the screen. Problem Solution Power can not be turned on.
EN-41 No image appears on the screen. (continued) Problem Solution The screen for entering the password appears. P ASSWORD FUNCTION in the FEA TURE menu has been set to DISPLA Y INPUT to enable the password lock. Enter the password or contact the person in char ge of management of the projector .
EN-42 Others Problem Solution The exhaust vents emit warm air . This air comes out after cooling the inside of the projector . Y ou may feel hot, but this is not a malfunction. • The menu can’t be used. The microcomputers inside the pr ojector may be wrongly operating because of noise.
EN-43 Normal condition POWER ST A TUS CONDITION NOTE Steady red Off Stand-by Steady green Blinking green Lamp stand-by (about 1 minute) The POWER button cannot be used to switch between on and off.
EN-44 The specifi cations and outside appearance of the pr ojector are subject to change without prior notice. T ype LCD pr ojector Model HC7000 Display technology 0.74-inch LCD panel: 3 pieces (for R, G, B) (aspect ratio 16:9) Pixel: 1920 x 1080 = 2073600 pixels T otal 6220800 pixels Projection lens F 2.
EN-45 *1: When ASPECT in the FEA TURE menu is set to AUTO. *2: Available for the signal fr om the HDMI IN terminal. Important: Some computers aren’ t compatible with the projector . The projector’ s maximum resolution is 1920 x 1080 pixels. It may not display images of higher resolutions than 1920 x 1080 correctly .
EN-46 Specifi cations (continued) Connectors SERIAL (D-SUB 9-pin) 1 5 6 9 Pin No. Name I/O 1– – 2 TXD IN 3 RXD OUT 4– – 5 GND – 6– – 7– – 8– – 9– – COMPUTER IN/COMPONENT VIDEO IN (Mini D-SUB 15-pin) Pin No.
1 Zusho Baba, Nagaokakyo-City , Kyoto Japan M I T SUBIS HI ELECTRIC CORPORA T I O N A Mitsubishi Pr ojector W arranty , Sales Support and Service Information North America MDEA (Mitsubishi Digital Electronics America, Inc.) Presentation Products Division 9351 Jeronimo Road Irvine CA 92618, USA For Warranty Registration, visit: http://www .
Ein wichtiger Punkt beim Kauf des Geräts Mitsubishi Electronics HC7000 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Mitsubishi Electronics HC7000 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Mitsubishi Electronics HC7000 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Mitsubishi Electronics HC7000 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Mitsubishi Electronics HC7000 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Mitsubishi Electronics HC7000 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Mitsubishi Electronics HC7000 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Mitsubishi Electronics HC7000. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Mitsubishi Electronics HC7000 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
