Benutzeranleitung / Produktwartung FR-S500 des Produzenten Mitsubishi Electronics
Zur Seite of 196
TRANSIST ORIZED INVERTER FR-S 500 INSTRUCTION MANU AL (D etailed) FUNCTIONS Chapter 2 HEAD OFFICE:MITSUBISHI DENKI BLDG MARUNOUCHI T OKY O 10 0-8310 WIRING Chapter 1 PR O TECTIVE FUNCTIO NS Chapter 3 SPECIFICA TIONS Chapter 4 FR-S 500E -NA TRANSIST ORIZED INVER TER INSTRUCTION MANU AL (Detailed) A SIMPLE INVER TER FR-S520E-0.
A-1 1. Elect ric Shock Preve ntion Thank you for choosing this Mitsubi shi T ransistorized inverter . This instruction manual (detailed) provides instructions for advanced use of the FR- S500 series inverters. Incorrect handling might cause an unexpected fault.
A-2 2. Fire Pre vention 3. Injury P reventio n 4. Additional Instructions Also note the following points to prevent an accidental failure, injury , elec tric shock, etc. (1) T ransp ortation and inst allation CAUTION Mount th e invert er on a n incombu stibl e surface .
A-3 (2) Wirin g (3) T rial run (4) Operation CAUTION Do not fit capacitive equipment such as power factor correction capacitor , radio noise filter (option FR-BIF(-H)) or surge suppressor to the output of the inverter . The connection orientation of the output cables U, V , W to the motor will affect the direction of rotation of the motor .
A-4 (5) Emergency stop (6) Maintenance, inspectio n and part s replacement (7) Disposing of t he inverter (8) General inst ructions CAUTION The electronic thermal relay function does not guarantee protection of the motor from overheating.
I CONTENTS CONTENTS 1. WIRING 1 1.1 Standard connecti on diagram and terminal speci fications ..2 1.1.1 Standard c onnec tion diag ram .............. ........... ............ ........... ........... ........... . 2 1.1.2 Explanat ion of m ain circui t termi nals .
II 1.5.4 Start self -holdin g select ion (STO P signal ): Pr. 60 to Pr. 6 3 sett ing "5" ....... 34 1.5.5 Output s hut-off (MRS signa l): Pr. 60 to Pr . 63 se tting "6" ...... ............ ......... 34 1.5.6 External thermal relay in put: Pr.
III CONTENTS 2.3.18 Biases a nd gai ns of the frequen cy se tting vol tage (c urrent) (Pr. 38 , Pr. 3 9 , C2 to C7 ). ............ ........... ........... ........... ............ ........... .... 82 2.3.19 Start-time ground faul t detectio n selec tion (Pr.
IV 2.12.1 Mainten ance outp ut func tion (H1, H2 ) ...... ........... ............ ........... ........... .. 122 2.12.2 Current averag e valu e monitor signa l (H3, H 4, H5) ...... .... ....... .. 123 2.1 3 Cal ibra tion par amete rs .... ....... ...
V CONTENTS 3.2.11 Motor prod uces an noyin g sound .......... ........... ............ ........... ........... ........ 168 4. SPECIFICATIONS 169 4.1 Speci fica tion li st ...... .... .... ....... .... ..... .... ....... .... ..... ...... ..... .... .
1 Chap t er 2 Chap t er 3 Chap t er 4 Chap t er 1 1. WIRING This chapter explains the basic "wiring" for use of this p roduct. Always read the instructions before use. For description of "inst allation", refer to the instruction manual (basic).
2 Standard connectio n diagr am and t erminal sp ecifica tions 1.1 S t andard connection diagram an d terminal specificat ions 1.1.1 S tandard connection di agram Three-phase 200V power input Three-phase 400V power input REMARKS *1. The N/- te rminal is not pro vided f or the FR- S520E-0.
3 Standard connect ion di agram and t erminal sp ecifi cations 1 WIRING Single-phase 100V power input 1.1.2 Explanation of m ain circuit termina ls (1) Main c ircu it REMARKS • T o ensure safety.
4 Standard connectio n diagr am and t erminal sp ecifica tions (2) Control circui t Symbol T erminal Name Definition Input signals Cont act input STF Forward rotation st art Turn on the STF signal to st art forw ard r ot ati on an d turn it o ff to stop.
5 Standard connect ion di agram and t erminal sp ecifi cations 1 WIRING *1. Do not co nnect te rminals SD and PC eac h other or to the groun d. For si nk l ogic (fa ct ory se tt in g), t erm inal SD ac ts a s th e comm on te rmi nal of con t act inp ut.
6 Main circuit terminals 1.2 Main c ircuit ter minals 1.2.1 T erminal block layout 1) Thr ee-phase 2 00V power input • FR-S520 E-0.1 K, 0.2K-NA • FR-S520E-1.5K, 2.2K, 3.7K-NA • FR-S520 E-0.4K , 0.75K-N A 2) Thr ee-phase 4 00V power input • FR-S540E-0.
7 Main circuit termi nals 1 WIRING 3) Si ngle-pha se 100V power input • FR-S510WE-0.1K, 0.2K, 0.4K-NA • FR-S510WE-0.75K-NA CAUTION • Make sure the po wer ca bles are conn ected to the R/L1, S/L 2, T/L3 of the inve rter . Never con nect the power cable to the U, V , W of the inv erter .
8 Main circuit terminals 1.2.2 Cables, wiring length, and crimping terminals The following t able indicates a selecti on example for the wiring length of 20m (65.62 feet). 1) Three-phase 200V power input 2) Three-phase 400V power input 3) Single-phase 100V power input Wiring length 100m (328.
9 Main circuit termi nals 1 WIRING 1.2. 3 Wir ing inst ru ction s 1) Use insulation-sleeved crimping terminal s for the power supply and motor cables. 2) Appli cation of power to the output terminal s (U, V , W) of the inverter will damage the inverter .
10 Main circuit terminals 1.2.4 Selecti on of peripheral devices Check the capacity of the m otor applicable to the inverter you purchased. Appropriate peripheral devices must be selected according to the cap acity .
11 1 WIRING Main circuit termi nals 3) Single-phase 100V power input *2. For inst allat ions in the United S tates or C anada, th e circ uit break er must b e inv erse time or in sta nta neous trip ty pe. *3. The powe r facto r ma y be s light ly lowe r .
12 Main circuit terminals 1.2.5 Leakage c urrent and install ation of ground leakage circuit breaker Due to stati c capacit ances existing in the inv erter I/O wiring and motor , leakage currents fl ow through them. Since th eir values depend on the stati c capac itances, carrier frequency , etc.
13 Main circuit termi nals 1 WIRING (2) Line-to-l ine leakage curre nt s Countermeasures • Use the electronic thermal relay function o f the inverter . • Decrease the carrier frequency . Note that motor noise increases. Selection of Soft-PWM (Pr .
14 Main circuit terminals (3) Selecting the rat ed sensitivit y current f or the earth leakage ci rcuit breaker When using the earth leakage circuit breaker with the inverter circuit, select its rated.
15 Main circuit termi nals 1 WIRING CAUTION • The ground leakage circuit breaker should be installed to the primary (power supply) side of the inverter . • In the connection neutral point grounded system, the sensitivity cu rrent becomes worse for ground faults on the inverter secondary side.
16 Main circuit terminals 1.2.6 Power-off and magnetic contactor (MC) (1) Inverter input side magnetic cont actor (MC) On the inverter's input side, it is recommended to provide an MC for the following purposes.
17 Main circuit termi nals 1 WIRING 1.2.7 Regarding the ins tallation of the power factor improving reactor When the inverter is install ed near a large-cap acity power transformer (500kV A or more with the wiring length of 10 m (32.
18 Main circuit terminals 1.2.8 Regarding noise and the installation of a noise filter Some noise enters the inverter cau sing it to malfunc tion and others are generated by the inverter causing the malfunction of peripheral devices.
19 Main circuit termi nals 1 WIRING 1.2.9 Grounding precautions Leakage currents flow in the inverter. T o prevent an electric shock, the inverter and motor must be grounded. Grounding must conform to the requirements of nati onal and local safety regulations an d electrical codes.
20 Main circuit terminals 1.2.10 Power suppl y harmonics The inverter may generate power supply harmoni cs from its converter circuit to affect the power generator , power capacitor etc. Power supply har monics are different from noise and leakage currents in source, frequenc y band and transmission path.
21 Main circuit termi nals 1 WIRING 1.2.1 1 Inverter- driven 4 00V clas s motor In the PWM type inverter , a surge voltage attribut able to wiring constants is generated at the motor terminals. Es pecially for a 400V cl ass motor , the surge voltage m ay deteriorate the insulation .
22 How to use the control c ircuit terminals 1.3 How to use the control circuit ter minals 1.3.1 T erminal block layout In the control circuit of the inverter , the terminals are arranged as shown below: 1.3.2 Wiri ng i nst ructi ons 1) T erminals, SE and 5 are common to the I/O signals isolated from each other .
23 How to use the control circuit terminals 1 WIRING 1.3.3 Changing the control logic The input signals are set to sink logic. T o c hange the control logic, the jumper connector under the setting dial must be moved to the other position. Change t he jum per c onnect or pos ition using tweez ers, a pair of long-no se pl iers et c.
24 How to use the control c ircuit terminals 2) Source logic type • In this logic, a signal switches on when a current flows into the corresponding signal input terminal. T erminal PC is common to the contact i nput signals. For the open collector output signals, terminal SE is a positive external power supply terminal.
25 Input terminals 1 WIRING 1.4 Input terminals 1.4.1 Run (start) and stop (STF , STR, STOP) T o s tart and stop the moto r , first switch on the input power supply of the inverter (switch on the magn.
26 Input t erminal s *1: Also stopped by the . Refer to page 105. (2) Three-wire type connection (STF , STR, STOP) A three-wire type connection is shown on the right. Assign the st art self-holding signal (STOP) to any of the input terminals. T o mak e a reverse rotation s tart, set Pr .
27 Input terminals 1 WIRING St art/Stop Timing Chart (for two -wire type) Forward-Reverse Rotation Switch-Over Timing Chart REMARKS *1. The "starting fr equen cy" in Pr .
28 Input t erminal s 1.4.2 Connection of frequency setting potentiome ter and output frequency meter ( 10, 2, 5, 4, AU) The analog frequency setting input s ignals that may be entered are voltage and current signals.
29 Input terminals 1 WIRING (2) Current input (4, 5, AU) T o automatically perform operation under cons t ant pressure or temperature control using a fan, pump etc., enter the controller output signal of 4 to 20mADC across terminals 4-5. T er minals AU-SD must be shorted to use the 4 to 20mADC signal for operation.
30 Input t erminal s *When using the REX signal, an ex ternal command cannot be us ed to make a reverse rotation start. Multi-Speed Operatio n Connection Example Multi-Speed Setting Spe ed T erminal I nput Parameter Set Freque ncy Range Remarks REX- SD* RH- SD RM- SD RL- SD* Spe e d 1 (high speed) OFF OFF OF F Pr .
31 Input terminals 1 WIRING 1.4.4 Indicator connection and adjustme nt (AM) A full-scale 5VDC analog s ignal can be output from across terminals AM- 5. The analog output level can be calibrated by the operation panel or parameter unit (FR-PU04). T erminal AM function selection can be set in Pr .
32 Input t erminal s 1.4.5 Control circuit common termina ls (S D, 5, SE) T er minals SD, 5, and SE are all common terminals (0V) for I/O signals and are isolated from each other . T er minal SD is a common terminal for the cont act input terminals (STF , STR, RH, RM, RL).
33 How t o use t he inpu t sign als (a ssigned ter minals RL, RM, RH, STR) 1 WIRING 1.5 How to use the input signals (assigned ter minals RL, RM, RH, STR) 1.5.1 Multi-speed se tting (RL, RM, RH, REX signals ): Pr . 60 to Pr . 63 setting "0, 1, 2, 8" Remote setting (RL, RM, RH sign als): Pr .
34 How to use the in put s ignal s (assign ed ter minals RL, RM, RH, STR) 1.5.4 S tart self-holding selection (STO P signal): Pr . 60 to Pr . 63 setting "5" 1.
35 How t o use t he inpu t sign als (a ssigned ter minals RL, RM, RH, STR) 1 WIRING 1.5.6 External thermal relay input: Pr . 60 to Pr. 63 setting "7 " 1.
36 How to use the inpu t signals (as signe d termin als RL, RM, RH, STR) 1.5.8 Res et signal: Pr . 60 to Pr . 63 setting "10" Used to reset the alarm stop st ate establ ished when the inverter's protective function is activated. The reset si gnal immediately se t s the control circuit to the initial (cold) status, e.
37 How t o use t he inpu t sign als (a ssigned ter minals RL, RM, RH, STR) 1 WIRING 1.5.9 PID contr ol valid te rminal: Pr . 60 t o Pr . 63 setting "14" T o exercise PID control, turn on the X14 signal. When this signal is off, ordinary inverter operation is performed.
38 Connection to the Stand-Alone Option 1.6 Connection to the St and-Alone Option The inverter accepts a varie ty of stand-alone option unit s as required. Incorrect connection wil l cause inverter damage or accident. Connect and operate the option unit carefully in accordance with the corresponding option unit manual.
39 Connec tion to the S ta nd-Alone Option 1 WIRING 1.6.2 Connec tion of the high power factor converter (FR-HC) When connecting the high power fac tor conv erter (FR-HC) to suppres s power supply harmonics, perform wiring securely as s hown below . Incorrect connection will damage the high power factor converter and inverter .
40 Connection to the Stand-Alone Option 1.6.3 Connection of the power regeneration c ommon converter ( FR-CV) When connecting the FR-CV type power regener ation common converter , connect the inverter terminals (P, N) and FR-CV type power regeneration common converter terminals as shown below so that their signals match with each other .
41 Handling of the RS-485 connector 1 WIRING 1.7 Handling of the RS-485 connector 1.7.1 Connection of the parameter unit (FR-PU04) When connecting the parameter unit to the RS-485 connector , use the optional parameter unit connection cable (FR-CB2 ) .
42 Handling of th e RS-485 connecto r 1.7.2 Wiring of RS-485 c ommunication Use the RS-485 connector to perform communication operation from a personal computer etc.
43 Handling of the RS-485 connector 1 WIRING (2) Combination of computer and mult iple inverters ( 1:n conne ction) REMARKS Refer t o the fol lowing wh en fab ricatin g the ca ble on the user side .
44 Handling of th e RS-485 connecto r <Wiring met hods> 1) Wi ring of one RS-485 computer and one inverter 2) Wi ring of one RS-485 computer and "n" inverters (several inverters) REMARKS *1. Make connect ion in a ccordan ce with t he inst ructi on manu al of t he compu ter to be used with.
45 Design information 1 WIRING 1.8 Design i nformation 1) Provid e electrical and mechanic al interlocks for MC1 and MC2 which are used for commercial power supply-inverter switchover .
46 MEMO.
47 Chap t er 2 Chap t er 3 Chap t er 4 Chap t er 1 2. FUNCTIONS This chapter explains the "functions" for use of this product. For simple variable-speed operation of the inverter , the factory settings of the parameters may be used as they are.
48 Function (Parame ter) list Paramete r List 2.1 Function (Parameter) li st *1. The fac tory setti ng var ies with t he inv erter c apacity: 5% for FR-S540 E-1.5K a nd 2.2 K, 4% for FR -S540 E-3.7 K. CAUTION indicates that the setting can be changed during operation i f Pr .
49 Function (Parameter) list 2 FUNCTIONS Paramet er Li st The extended function parameters are made v alid by setting "1" i n Pr . 30 "extended function display sele ction". (For more det ailed information on the way to set Pr . 30, refer to the instruction manual (basic).
50 Function (Parame ter) list Paramete r List S tandard operat ion fun ctions 24 Multi-sp eed setting (speed 4) 0 to 120Hz, - - - 0.1Hz - - - 66 25 Multi-sp eed setting (speed 5) 0 to 120Hz, - - - 0.1Hz - - - 66 26 Multi-sp eed setting (speed 6) 0 to 120Hz, - - - 0.
51 Function (Parameter) list 2 FUNCTIONS Paramet er Li st Output termi nal func tions 41 Up-to- frequen cy sensi tiv ity 0 to 100% 1% 10% 86 42 Output frequen cy detect ion 0 to 120Hz 0.1Hz 6Hz 87 43 Output frequen cy detect ion fo r revers e rotation 0 to 120Hz , - - - 0.
52 Function (Parame ter) list Paramete r List Display fu nctions 52 Oper ation panel d isplay data se lecti on 0: Outpu t freque ncy , 1: Ou tput c urre nt, 100:Set fr eque ncy duri ng stop /out put f.
53 Function (Parameter) list 2 FUNCTIONS Paramet er Li st T ermin al func ti on s el ect ion 60 RL termin al functi on selec tion 0: RL, 1: RM, 2: RH, 3: RT , 4: AU, 5: STO P , 6: MRS, 7: OH, 8: REX, 9: JOG , 10: RE S, 14: X14, 16: X16, - - -: S TR ( The S TR signal can be assign ed to the ST R term inal onl y .
54 Function (Parame ter) list Paramete r List Oper at ion s el ecti on functions 70 Soft- PWM setting Presence /absence of Soft-PW M control c an be selected . When Soft-PWM is valid, the met allic tone of motor no ise can b e changed in to unoffe nding com posite tone.
55 Function (Parameter) list 2 FUNCTIONS Paramet er Li st Operation selec tion function s 75 Reset select ion/PU stop sel ection 0: Res et normal ly enable d/PU stop key disa bled 1: En abled a t a la.
56 Function (Parame ter) list Paramete r List Multi-sp eed ope ration funct ion 84 Multi-sp eed setting (speed 12 ) 0 to 120Hz, - - - 0.1Hz - - - 66 85 Multi-sp eed setting (speed 13 ) 0 to 120Hz, - - - 0.1Hz - - - 66 86 Multi-sp eed setting (speed 14 ) 0 to 120Hz, - - - 0.
57 Function (Parameter) list 2 FUNCTIONS Paramet er Li st Maintenance parameters Additional p arameters Parameter for manufacturer setting Func- tion Parame- ters Indi- cation Na me Setting Range Mini.
58 Function (Parame ter) list Paramete r List Calibration parameters * Factory settings may dif fer because of calibration p arameters. Func- tion Parame- ters Indi- cation Name S etting Range Minimum.
59 Function (Parameter) list 2 FUNCTIONS Paramet er Li st Communication Parameters Func tion Parame- ter Indica - tion Name Set ting Rang e Minimum Setting Incre- ments Factory Setting Refer To : Cus- tomer Setting Communication Parameters n1 (3 31) Communication statio n number 0 to 31: S pecify the s tation number of th e inverter.
60 Function (Parame ter) list Paramete r List PU parameters When the parameter un it (FR-PU04) is used, operation from the ope ration panel i s not accepted.
61 List of parame ters classi fied by purpose o f use 2 FUNCTIONS 2.2 List of p arameters classified by purpose of use Set the parameters according to the operating c onditions. The foll owing list indic ates purpose of use and corresponding parameters.
62 List of parameters classified by pu rpose of use Related to monitor ing Freque ncy met er cali bratio n Pr . 54 , Pr . 55, P r . 56, cali brat io n pa ram eter C1 Dis play o f mon ito r on operat ion panel o r parame ter unit (F R-PU 04) Pr . 52, Commun ication paramet er n16 Displa y of spe ed, etc.
63 Explanation of functions ( parameters) 2 FUNCTIONS 2.3 Explanation of functions (p arameters) 2.3.1 T orque boost (Pr . 0 , Pr . 46 ) <Setting> • Assuming that the base frequency volt age is 100%, set the 0Hz voltage in %. Use the R T signal to s witch between two di fferent to rque boosts.
64 Explanation of functions (p arameters) 2.3.2 Maximum a nd minimum fr equency (Pr . 1 , Pr . 2 ) <Setti ng> • Use Pr . 1 to set the upper limit of the output frequency . If the frequency of the frequency command entered is higher than the setting, the output frequency is clamped at the maximum frequency .
65 Explanation of functions ( parameters) 2 FUNCTIONS 2.3.3 Base f requency , base freque ncy voltage (Pr .3 , Pr .19 , Pr .47 ) *1. 1.9 ti mes gre ater th an the power su pply vol tage for th e FR-S510W E-0.1K to 0.75 K. *2. T wic e gr eater than t he p ower supply vol ta ge for the FR -S51 0WE-0.
66 Explanation of functions (p arameters) 2.3.4 Multi-speed operation (Pr . 4 , Pr . 5 , Pr . 6 , Pr . 24 to Pr . 27 , Pr . 80 to Pr . 87 ) <Setti ng> • Set the running frequencies in the corresponding p arameters. Each speed (frequency) can be set as desired between 0 and 120Hz during inverter operation.
67 Explanation of functions ( parameters) 2 FUNCTIONS 2 . 3 . 5 Accelerat ion/decelera tion tim e (Pr . 7 , Pr . 8 , Pr . 20 , Pr . 44 , Pr . 45 ) CAUTION 1. The mult i-speed setting s override the main speeds (across terminals 2-5, 4- 5, setting dial).
68 Explanation of functions (p arameters) <Setti ng> • Use Pr . 7 and Pr . 44 to set the accelerati on time required to reach the frequency set in Pr . 20 from 0Hz. • Use Pr . 8 and Pr . 45 to set the decelerati on time required to reach 0Hz from the frequency set in Pr .
69 Explanation of functions ( parameters) 2 FUNCTIONS 2.3. 6 Selection and prot ection of a motor (Pr . 9 , Pr . 71 , H7 ) • The parameter nu mber in parenth eses is th e one for use with t he parameter uni t (FR-PU04 ). <Setting> • Refer to the follow ing list an d se t Pr .
70 Explanation of functions (p arameters) REMARKS • When run ning two mot ors wit h one in vert er , you can set the electr onic th ermal rela y funct ion of each in verter. CAUTION Set this para meter correctly according to the motor used. Incorrect setting may cause th e motor to overheat and burn.
71 Explanation of functions ( parameters) 2 FUNCTIONS 2.3.7 DC injection brake (P r . 10 , Pr . 1 1 , Pr . 12 ) * The factor y setting va ries accord ing to the inverter capaci ty . (Refer to the follo wing table for detai ls.) <Setting> • Use Pr .
72 Explanation of functions (p arameters) 2.3.8 S tarting frequency (P r . 13 ) The starting frequency at which the st art signal is turned on can be set in the range 0 to 60Hz. Parameter Na me Factory Settin g Setti ng Range Remarks 13 S tarting fr eque ncy 0.
73 Explanation of functions ( parameters) 2 FUNCTIONS 2.3.9 Load patter n selectio n (Pr . 14 ) Y ou can select the optimum output characteristic (V/F characteristic) for the application and load characteristic s.
74 Explanation of functions (p arameters) 2.3.10 Jog operation (Pr .15 , Pr .16 ) Set the frequency and acceleration/deceleration time for jog operation.
75 Explanation of functions ( parameters) 2 FUNCTIONS 2 . 3. 12 S t all prevention function and current limit function (Pr . 21 ) Y ou can make setting to prevent stall caused by overc urrent and/ or .
76 Explanation of functions (p arameters) CAUTION • If the load is heavy , th e lif t is pred etermined, or the acceleration/deceleration time is short, the stall prevention may be activated and t he motor not sto pped in the preset acceleration/deceleration time.
77 Explanation of functions ( parameters) 2 FUNCTIONS 2.3.13 S tall pre ven tion (P r . 22 , Pr . 23 , Pr . 28 ) <Setting> • Generally , set 150% (factory setting) in Pr . 22 "stall prevention operatio n level". Setting "0" in Pr .
78 Explanation of functions (p arameters) to Refer to to (p age 66 ) REMARKS When t he hi gh re spon se c urr ent limi t is set i n Pr . 21 "st all prev ent ion func ti on se lect ion " (factor y setting ), do not set any value abo ve 170% i n Pr .
79 Explanation of functions ( parameters) 2 FUNCTIONS 2.3.14 Acceleration/deceleration pattern (Pr . 29 ) <Setting> Set the acceleration/deceleration pattern. Para mete r N a m e Fact ory Setti ng Setti ng Range Remarks 29 Accelerat ion/ decelerat ion pattern 0 0 , 1 , 2 Setting is enabled wh en Pr .
80 Explanation of functions (p arameters) 2.3.15 Extended function display selection (Pr . 30 ) 2.3.16 Frequency jump ( Pr . 31 to Pr . 36 ) <Setti ng> Used to display the extended function p arameters. Refer to page 48 for the extended function p arameter list.
81 Explanation of functions ( parameters) 2 FUNCTIONS 2.3. 17 Speed di spla y (Pr . 3 7 ) <Setting> • T o display the machine speed, set in Pr . 37 the machine speed for 60Hz operation. Y ou can change the output frequency indication or set frequency of the operation panel and param eter unit (FR-PU04) to the motor speed or machine speed.
82 Explanation of functions (p arameters) 2.3.18 Biases and ga ins of t he fr equency set ting voltage (current) (Pr . 38 , Pr . 39 , C2 to C7 ) *1.F acto ry set tings m ay differ becaus e of cali brati on paramet ers. *2.T he param eter num ber in par enthe ses is th e one for use with the parame ter un it (FR-P U04).
83 Explanation of functions ( parameters) 2 FUNCTIONS <Setting> (1) How to change the highest frequency (2) Adjusting the deviation of the hi ghest frequency from the Pr .
84 Explanation of functions (p arameters) (2) Adjusting a deviat ion of the highest fr equency from the Pr . 38 (Pr . 39) setting. (2)-1 Making a djustment with a volt age applied dire ctly ac ross te.
85 Explanation of functions ( parameters) 2 FUNCTIONS (2)-2 Making ad just ment at an y poin t wit h a vol t age not applie d acros s term inals 2- 5 (wit hout a curren t flowi ng acros s terminal s 4.
86 Output terminal function param eters 2.3.19 Start-time ground faul t detection selection (Pr . 40 ) 2.4 Output termin al function p ara meters 2.4.1 Up-to-frequency (Pr . 41 ) Use Pr . 64 or Pr . 65 (output terminal function selection) to assign the terminal used for SU signal output.
87 Output terminal function parameters 2 FUNCTIONS 2.4.2 Output frequency detection (Pr . 42 , Pr . 43 ) <Setting> Refer to the above chart and set the corresponding parameters. • When Pr . 43 "output frequency detection for revers e rotation" ≠ "- - -", the Pr .
88 Curre nt dete ctio n func tion pa ramet ers 2.5 Current detection function p arameters 2.5.1 Output current detection f unctions (Pr . 48 , Pr . 49 ) <Setti ng> Use Pr . 64 or Pr . 65 (output terminal function selection) to assign the terminal used for Y12 signal output.
89 Curre nt dete ctio n func tion pa ramet ers 2 FUNCTIONS 2.5.2 Zero current detection (Pr . 50 , Pr . 51 ) <Setting> Use Pr . 64 or Pr . 65 (output terminal function selection) to assign the terminal used for Y13 signal output. When the inverter's output current falls to "0[A]", torque will not be generated.
90 Display function parameters 2.6 Display function p arameters 2.6.1 Monitor display (P r . 52 , Pr . 54 ) <Setti ng> When "100" is set in Pr . 52, the monitored values during stop and during operation differ as indicated below . Y ou can choose the display of the operation panel "monitor/frequency setti ng screen".
91 Displa y func tion pa ramet ers 2 FUNCTIONS 2.6.2 Setting dial function selection (Pr . 53 ) Using the setting d ial like a poten tiometer to perform o peration Refer to (p age 90 ).
92 Restart operation parameters 2.6.3 Monitoring refer ence (Pr . 55 , Pr . 56 ) <Setti ng> Refer to th e abo ve diag rams a nd s et the freq uency mo nit oring r efer ence va lue i n Pr . 55 and the current monitori ng reference value in Pr . 56.
93 Restart operation parameters 2 FUNCTIONS <Setting> Refer to the following table and set the p arameters: Param eter Set ting Descript ion 57 0 0.1K to 1.5K Co asting ti me of 0.5s Gener ally , this settin g will pose no prob lems. 2.2K, 3.7K Coas ting time of 1.
94 Restart operation parameters REMARKS • When the start sign al is tur ned off du ring powe r fail ure and power is re stor ed With out sp eed sea rch (H6 =1): Deceler ates to stop aft er run ning in the sa me dire ctio n befo re power f ailure. Note that th e motor will co ast if t he st art signal is tur ned off duri ng res tart opera tion.
95 Addition al fu nction param eters 2 FUNCTIONS 2.8 Additional fun ction pa rameters 2.8.1 Remote setting function sele ction (Pr . 59 ) * External running frequency (other than multi-speed) or PU ru.
96 Additio nal func tion pa rameter s <Setti ng> • Use Pr . 59 to select whether the remote setting function is used or not and whether the frequency setting storage function* in the remote setting mode is used or not.
97 Addition al fu nction param eters 2 FUNCTIONS <Frequency set ting stor age condit ions> • The frequency at which the start signal (STF or STR) turns off is stored. • The remotely-set frequency is stored every one minute a fter one mi nute has elap sed since turn off (on) of both the RH (acceleration) and RM (deceleration) signals.
98 T ermin al fu nction sel ection param eters 2.9 T erminal function se lection p arameters 2.9.1 Input terminal function s election (Pr . 6 0 , Pr . 61 , Pr . 62 , Pr . 63 ) CAUTION • The frequency can be varied by RH (acceleration) and RM (deceleration) between 0 and the m aximum frequency (Pr .
99 Terminal function selection parameters 2 FUNCTIONS <Setting> Refer to the following table and set the p arameters: *1.When Pr . 59 = "1 or 2", the functions of the RL, RM and RH signals change as listed above. *2.Actuated when the relay contac t "opens".
100 T ermin al fu nction sel ection param eters 2. 9 .2 Out put terminal functio n selection (Pr . 64 , Pr . 65 ) <Setti ng> Y ou can change the functions of the open collector output terminal and contact output terminal.
101 Opera tion selec tion fu nction paramete rs 2 FUNCTIONS 2.10 Operation sel ection function p aramet ers 2 . 1 0 . 1 Retry function (Pr . 66 , Pr . 67 , Pr . 68 , Pr . 69 ) <Setting> • Use Pr . 66 to select the protec tive functions (major faults) to be activated for retries.
102 Operation selection function parameters CAUTION • The cumulative n umber in Pr . 69 is incremented by "1" when retry op eration is regarded as successful, i.e. when normal op eration is contin ued without the protective function (major fault) acti vated during a period four times lon ger than the time set in Pr .
103 Opera tion selec tion fu nction paramete rs 2 FUNCTIONS 2.10.2 PWM ca rrier frequenc y (Pr . 70 , Pr . 72 ) <Setting> • By parameter setting, you can set whether to exercise Sof t-PWM control that changes the motor tone.
104 Operation selection function parameters 2.10.3 V oltage input selection (P r . 73 ) Y ou can change the i nput (termi nal 2) speci fications ac cording to the frequenc y setting vo ltage signal. When ent ering 0 to 10VDC, alway s make thi s setting.
105 Opera tion selec tion fu nction paramete rs 2 FUNCTIONS 2.10.4 Input filter time constant (Pr . 74 ) <Setting> Increase the filter time constant if steady operati on cannot be perfor med due to noise. A larger setting results i n slower response.
106 Operation selection function parameters (1) How to make a rest art af ter a stop by the input fr om the operation p anel (Rest artin g method wit h shown) (2) How to make a rest art when a stop is.
107 Opera tion selec tion fu nction paramete rs 2 FUNCTIONS 2.10.6 Cooling fan operation selection (Pr . 76 ) <Setting> CAUTION Do not reset the inverter with t he st art signal on. Otherwise, the motor will start inst antly af ter resetting, leading to potentially hazardous con ditions.
108 Operation selection function parameters 2.10.7 Paramet er write dis able sele ction (Pr . 77 ) <Setti ng> Y ou can select between write-enable and disable for parameters. This function is used to prevent parameter values from being rewritten by incorrect operation.
109 Opera tion selec tion fu nction paramete rs 2 FUNCTIONS 2.10.8 Reverse rotation preventi on selection (P r . 78 ) <Setting> 2.10.9 Operation mode selec tion (Pr . 79 ) This function can prevent reverse rotation faults resulting from the incorrect input of the start signal.
11 0 Operation selection function parameters <Setti ng> In the following t able, operation using the op eration panel or p arameter unit is abbreviated to PU operation. Pr . 79 Setting Function LED Indi cation * RUN PU EXT 0 At power on , the inv erte r is put in the ex tern al operat ion mod e.
111 Opera tion selec tion fu nction paramete rs 2 FUNCTIONS (1) PU operation interlock PU operation interlock forces the operation mode to be changed to the ex ternal operation mode when the MRS signal switches off.
11 2 Operation selection function parameters (2) Operation mode switching by external signal 1) Preparation Set "8" (switching to other than external operation mode) in Pr . 79. Use any of Pr . 60 to Pr . 63 (input terminal function selection) to set the terminal used for X16 signal input.
11 3 Opera tion selec tion fu nction paramete rs 2 FUNCTIONS 2.10.10 PID control ( Pr . 88 to Pr . 94 ) <Setting> (1) Basic PID control confi guration (2) PID action overview The inverter can be used to exercise process control, e.g. fl ow rate, air volume or pressure.
11 4 Operation selection function parameters 2) PD action A combination of proportional control action (P) and di fferential control action (D) for providing a manipulated variable in response to deviation s peed to improve the transient characteristic.
11 5 Opera tion selec tion fu nction paramete rs 2 FUNCTIONS Relationships between deviation and ma nipu lated variable (output frequency) (3) Wiring example 5) Forw ard action Increases the manipulat.
11 6 Operation selection function parameters (4) I/O s ignals • Enter the set point acr oss inverter terminals 2-5 or in Pr . 93 and enter the measured value signal across inverter terminals 4-5. • T o exercise PID control, turn on the X14 signal.
11 7 Opera tion selec tion fu nction paramete rs 2 FUNCTIONS (6) Adjustment procedure 91 PID upper limi t 0 to 100% Set the up per lim it. If t he feedba ck val ue exce eds the setti ng, th e FUP signa l is ou tput. ( Measur ed val ue of 4mA is eq uivale nt to 0% a nd 20mA to 100%.
11 8 Operation selection function parameters (7) Calibrati on example (A detector of 4mA at 0°C (32°F) and 20mA at 50°C (122°F) is used to adjust the room temperature to 25°C (77°F) under PID control. The set point is given to across inver ter terminals 2-5 (0-5V).
11 9 Opera tion selec tion fu nction paramete rs 2 FUNCTIONS <Set point input calibration> 1. Apply the input voltage of 0% set point setting (e.g. 0V) across terminals 2-5. 2. Make calibration using the calibration parameters C2, C3. At this time, enter in C2 the frequency which should be output by the inverter at the deviation of 0% (e.
120 Auxiliary parameters 2.1 1 Auxiliar y p a rameters 2.1 1.1 Slip compe nsation (P r . 95 , Pr . 96 , Pr . 97 ) <Setti ng> *When this value is made smaller , response will be faster . However , as load inertia is greater , a regenerative overvoltage (OVT) error is more liable to occur .
121 Auxiliary parameters 2 FUNCTIONS 2.1 1.2 Automatic torque boost selec tion (Pr . 98 ) <Operating condi tions> • The number of motor poles should be any of 2, 4 and 6 poles. • Single-motor operation (One motor for one inverter) • The wiring length from inverter to motor should be within 30m (98.
122 Maintenance parameters 2.1 1.3 Motor primary resis tance (Pr . 99 ) 2.12 Maintenance p arameters 2.12.1 Maintenance output function (H1 , H2 ) The parameter numbers in parentheses are those for use with the parameter unit (FR - PU04). <Setti ng> Generally this parameter need not be set.
123 Maintenance parameters 2 FUNCTIONS 1) H1 (Pr . 503) "maintenance timer" • The cumulative energization time of the inverter is stored into the E 2 PROM every hour and indicated in 1000h increments. (Cannot be written.) • The maintenance timer is clamped at 999 (999000h).
124 Maintenance parameters <Pulse operation> The output pulse of the Y93 signal is shown below . <Setting> Perform setting according to the following steps.
125 Maintenance parameters 2 FUNCTIONS 4) Output of maintenance timer value (maintenance parameter H1) After the output current average value is output as low pulse shape, the maintenance timer value is output as high pul se shape. The output time of the maintenance timer value is obtained from the following calculation.
126 Calibr ati on paramet ers 2.13 Calibration p arameters 2.13.1 Meter (frequency meter) calibration (C1 ) The parameter number in parentheses is the one for use with the parameter unit (FR- PU04). The AM terminal is factory-set to provide 5VDC output in the full-scale status of each monitor item.
127 Calibration parameters 2 FUNCTIONS Changing example Deflecting the meter (analog indicator) to full-scale (5V) at the preset frequency of 60Hz (for frequency setting, refer to the instruction manual (basic).
128 Calibr ati on paramet ers to Refer to , ( page 82). POINT By setting the Pr . 54 "AM terminal function selection" value, preset Pr . 55 "frequency monitoring reference" or Pr . 56 "current monitoring reference" to the running frequency or current value at which the output signal is 5V .
129 Clear parameters 2 FUNCTIONS 2.14 Clear p arameters 2.14.1 Parameter c lear (CLr ) *1.Parameters are not cleared by setting "1" i n Pr . 77 "parameter write disable select ion". Pr . 75, Pr . 38, Pr . 39, Pr . 53, Pr . 60 to Pr .
130 Communication parameters 2.15 Communicatio n p aramet ers (1) Operational funct ions 1) Operation mode switching [Operation mode switching method] *1.
131 2 FUNCTIONS Communication parameters 2) Operation mode-based functions *1. As set in the co mmun ication para meter s n8 "operat ion com mand sou rce" and n9 "sp eed comman d sourc e". (ref er to page 147) *2. At occurrence of RS-48 5 commun ication er ror , the inverter cann ot be res et from the co mputer .
132 Communication parameters 2.15.1 Communication settings (n1 t o n7 , n1 1 ) Communication-related parameters • The parameter numbers within p arentheses are those for use of the parameter unit (FR-PU04). • Refer to page 180 for the instruction codes.
133 Communication parameters 2 FUNCTIONS <Setting> T o make communication between the personal computer and inverter , initialization of the communication specifications must be made to the inverter . If initial setting is not made or there is a setting fault, data transfer cannot be made.
134 Communication parameters <Computer programming> (1) Communication protocol Data communication between the computer and inverter is performed using the following procedure: (2) Communication .
135 Communication parameters 2 FUNCTIONS (3) Data f ormat Data used is hexadecimal. Data is automatically transferred in ASCII between the c omputer and inverter .
136 Communication parameters 4) Send dat a from computer to inverter durin g data read (4) Dat a definitio ns 1) Control codes 2) Inverter st at ion number S pec ify the station number of the inverter which communicates with the computer . 3) Instruction code S pec ify the processing request, e.
137 Communication parameters 2 FUNCTIONS 5) W aiting time S pec ify the waiting time between the receipt of data at the inverter from the computer and the transmission of reply data. Set the waiting time in accordance with the response time of the computer between 0 and 150ms in 10ms increments (e.
138 Communication parameters 7) Open cable detection (Communication parameter n6 "communication check time interval") · If disconnection (communication stop) is detected between the inverter and computer as a result of disconnection check, a communication error (OPT) occurs and the inverter output is shut off.
139 Communication parameters 2 FUNCTIONS 8) Sum check code The sum check code is 2-digit ASCII (hex adecimal) representing the lower 1 byte (8 bits) of the sum (binary) derived from the checked ASCII .
140 Communication parameters CAUTION Always set the communicatio n check time interval bef ore st arting operation to prevent hazardous conditions. Dat a communication is not star ted automatically but is made only once when the computer pro vides a comm unication requ est.
141 Communication parameters 2 FUNCTIONS <Setting items and set dat a> Aft er compl etion of p arame ter sett ings, s et the i nstruc tion c odes a nd dat a then st art communicati on from th e computer to allow vario us types of operation control and monit oring.
142 Communication parameters 3 Run command HF A * Fun ction ch ange ca n be made us ing Pr . 60 to Pr . 63 (inp ut term inal func tio n select ion). 2 digi ts 4 Inver ter st atus monitor H7A * Fun ction c hange ca n be ma de usi ng Pr . 64 an d Pr . 65 (out put te rmina l funct ion sele ction) .
143 Communication parameters 2 FUNCTIONS 5 Set fr eque ncy read (RAM) H6D • When Pr . 37 = "0" (fa ctory s etti ng) The set fr equen cy (RAM or E 2 P ROM) is r ead. H0000 to H2E E0: 0. 01Hz incr ements • When Pr . 37 = " 0.1 to 99 9", ex pansio n link parame ter (HFF ) = 0 The se t spee d is rea d.
144 Communication parameters 8 All param eter clear HF C All p aramet ers return to th e fact ory sett ings. Any of fo ur differ ent all clear ope ratio ns are pe rform ed acco rding t o the da ta. When al l paramete r clear i s execut ed for H969 6 or H9966, comm unicat ion-r elated parameter se ttings also retur n to the fa ctor y setti ngs.
145 Communication parameters 2 FUNCTIONS <Error Code List> The corresponding error code in the following list is displayed if an error is detected in any communication request data from the computer: (5) Operation at al arm occurre nce *3: C an be selected using the corresponding parameter (factory-set to stop).
146 Communication parameters (7) Program example Program General flowchart T o change the operation mode to computer link operation 1000 *REC 1010 IF LO C(1)=0 THEN R ETURN 1020 PRINT "RECEIV E D.
147 2 FUNCTIONS Communication parameters 2.15.2 Operation and spee d command s ource (n8 , n9 ) The parameter numbers within parentheses are those for use of the parameter unit (FR-PU04). <Setting> In the computer operation mode, commands from the external ter minals and computer are as listed below .
148 Communication parameters [Explanation o f t able] External : O peration is valid only from external terminal signal. Computer : Operation is valid only from computer . Combined : O peration is valid from either of external terminal and computer . : Operation is invalid from either of external terminal and computer .
149 2 FUNCTIONS Communication parameters <Setting> • n10 can be changed independently of the operation mode of the operation panel. • Setting of n10 = "1" is made valid when "0" or "2" is set in Pr . 79 "operation mode select ion" .
150 Communication parameters 2.15. 4 E 2 PROM write selection ( n12 ) The param eter number i n parenth eses is th e one for use wi th t he paramet er un it (FR- PU04). Y ou can choose whether the parameters are stored into the E 2 PROM or not at the parameter setting for computer communication.
151 Parameter un it (FR-PU04) setting 2 FUNCTIONS 2.16 Parameter unit (FR-PU04) s etting 2.16.1 PU display la nguage select ion (n13 ) The parameter number in parentheses is the one for use wi th the parameter unit (FR- PU04).
152 Parameter unit (FR-PU04) set ting 2.16.3 PU contra st adjust ment (n15 ) The parameter number in parentheses is the one for use with the parameter unit (FR- PU04). 2.16.4 PU main disp lay scree n data se lecti on (n16 ) The parameter number in parentheses is the one for use with the parameter unit (FR- PU04).
153 Parameter un it (FR-PU04) setting 2 FUNCTIONS 2.16.5 Disconnected PU detection/PU s etting lock selection (n17 ) The parameter number in parentheses is the one for use wi th the parameter unit (FR- PU04). <Setting> * The monitor display and the are valid.
154 MEMO.
155 Cha pt e r 2 Cha pt e r 3 Cha pt e r 4 Cha pt e r 1 3. PROTECTIVE FUNCTIONS This chapte r explains the "p rotectiv e functions" of this product. Always read the i nstructio ns b efore using the e quipment. 3.1 Erro rs (A larm s) ... ....
156 Errors (Alarms) 3.1 Errors (Alarms) If any fault has occurred in the inverter , the corresponding protective function is activated to bring the inverter to an alarm stop and automatically give the corresponding error (alarm) indication on the PU display .
157 Errors (Alarms) 3 PROTECTIVE FUNCTIONS 3.1.1 Error (alarm) definitions (1) Maj or fai lure s When the prot ective function is activated, the inverter output is s hut of f and the alarm is output.
158 Errors (Alarms) Operati on Panel I ndic ation OV1 F R-PU04 OV During Acc Name Regen erativ e overvol tage shut- off durin g acceler ation Descripti on When the main circ uit DC volt age in the inv.
159 Errors (Alarms) 3 PROTECTIVE FUNCTIONS *1. Resetting the inverter initializes the internal thermal integratied data of the electronic thermal relay function.
160 Errors (Alarms) *2. Functions only when any of Pr . 60 to Pr . 63 (input terminal function selection) is set to OH. Operati on Panel I ndic ation GF FR-PU04 Ground Fault Name S tart-tim e output s.
161 Errors (Alarms) 3 PROTECTIVE FUNCTIONS (2) Minor fail ures When the protective function is acti vated, the output is not shut of f. Y ou can make parameter setting to output the minor fault signal. (Set "98" in any of Pr . 64, Pr . 65 (output terminal function selection).
162 Errors (Alarms) (3) W arnings *3. The stall prevention operation current can be set as desired. It is factory-set to 150%. Operati on Panel I ndic ation OL FR-PU04 OL Name S tall preventi on (over.
163 Errors (Alarms) 3 PROTECTIVE FUNCTIONS Operati on Panel Indicat ion PS FR-PU04 PS Name PU stop Description Pr . 75 "res et sele ction/ PU stop sel ection " had b een s et and a sto p was m ade b y pres sing the of the ope ration panel or paramet er unit (FR-PU0 4) durin g oper ation in th e exte rnal operat ion mod e.
164 Errors (Alarms) (4) Write e rrors Operati on Panel I ndic ation Er1 FR-PU0 4 Control Mode Name Write disab le erro r Descripti on • Wri te wa s pe rfor med wi th "1" ( writ e disa ble) set in P r . 77 "parameter write di sable se lecti on".
165 3 PROTECTIVE FUNCTIONS Errors (Alarms) 3.1.2 T o know the operating status at the occurre nce of alarm (only when FR -PU04 is used) When any alar m has occur red, the dis play automati cally swit ches to the i ndication of the correspond ing prot ective functi on (error) .
166 Troubl esh ooti ng 3.2 T roubleshooting POINTS If the cause is still unk nown after every check, it is rec ommended to initialize the parameters (return to factory setting) then re-set the required p arameter values and check again.
167 Tr oublesho otin g 3 PROTECTIVE FUNCTIONS 3.2.2 Motor rot ates in oppo site d irection Check that the phase sequence of output terminals U, V and W is correct. Check that the start signals (forward rotation, reverse rotation) are connected properly .
168 Troubl esh ooti ng ................ Check the Pr . 79 setting. When the Pr . 79 "operation mode selection" setting is "0", switching input power on places the inverter in the external operation mode. Press the to switch to the PU operation mode.
169 Chap t er 2 Chap t er 3 Chap t er 4 Chap t er 1 4. SPECIFICA TIONS This ch apter provi des t he "specif ications" of this produc t. Always read the i nstructio ns b efore using the e quipment 4.1 Specific atio n lis t ... ..... .... ....
170 Specification list 4.1 Specificat ion lis t 4.1.1 Ratings (1) Three-phase 200V power supply *1. The a pplied motor capacity indica ted i s the m aximum capacity applic able for use o f the Mitsu bishi 4-po le stand ard moto r . *2. The rat ed out put capacit y indic ated a ssumes that the outpu t voltage is 23 0V .
171 Spec ifica tion li st 4 SPECIFICATIONS (2) Three-phase 400V power supply *1. The applied motor capaci ty indi cate d is the max imum ca pacity applic able for u se of th e Mitsu bishi 4- pole stand ard mot or . *2. The r ated ou tput ca pacity indicat ed ass umes th at the out put v oltage is 44 0V .
172 Specification list (3) Single-phase 100V power supply *1. T he appl ied mo tor ca pacity indi cat ed is the maximum capacity appl icable when a Mitsu bishi 4-pole standar d mo tor i s used . *2. The rat ed out put capacit y indic ated a ssumes that the outpu t voltage is 23 0V .
173 Spec ifica tion li st 4 SPECIFICATIONS 4.1. 2 Common specifications Control specifications Contro l syst em Selectabl e bet ween Soft-P WM cont rol and high ca rrie r freque ncy PWM control, V/F contr ol or aut omati c torque boost co ntro l are sel ectable.
174 Specification list *1. When un dervolt age or inst ant aneous powe r failure occurs , no a larm o utput is provide d but the output is shut o ff. A fter pow er restor ation, the i nverter may b e run a s it is. D epending o n the runnin g stat us (e.
175 Outline d rawin gs 4 SPECIFICATIONS 4.2 Out line dr awi ngs • FR-S520E-0.1K, 0.2K, 0.4K, 0.75K-NA • FR-S510WE-0.1K, 0.2K, 0.4K-NA • Three-phase 200V power supply • Single-phase 100V power supply (Unit: mm (inches)) Capacity D D1 D2 0.1K ,0.
176 Outlin e dr awings • FR-S520E-1.5K, 2.2K, 3.7K-NA • FR-S540E-0.4K, 0.75K, 1.5K, 2.2K, 3.7K-NA • FR-S510WE-0.75K-NA • Three-phase 200V power supply • Three-phase 400V power supply • Single-phase 100V power supply (Unit: mm (inches)) Cap ac ity W W1 D D1 D2 D3 1.
177 Outline d rawin gs 4 SPECIFICATIONS • Parameter unit (FR-PU04) <Outline drawing> < Panel cut dimension drawing> Choose the mounting screws whose length will not exceed the effective depth of the mounting threads. 125 ( 4. 92) 5-M3 ho l e 5- 4 hol e Effective depth 4.
178 MEMO.
179 APPENDIX APPENDIX 1 Parameter In struction Code List ....... 180.
180 Parameter Instruction Code L ist APPEND IX 1 Parame ter Instru ction Code List The extended function p arameters are made valid by setti ng "1" in Pr .
181 Parameter Instruction Code List S tandard operatio n function s 23 S tall pr even tion ope ratio n level co mpensa tion factor at doubl e speed 17 97 0.1% 0 24 Multi -spee d setti ng (speed 4) 18 98 0.01Hz 0 25 Multi -spee d setti ng (speed 5) 19 99 0.
182 Parameter Instruction Code L ist Disp lay fu nct ion s 52 Oper atio n p anel d isp lay dat a sele ction 34 B4 1 0 53 Frequen cy setti ng operat ion sele ction 35 B5 1 0 54 AM term inal func tion sele ction 36 B6 1 0 55 Frequen cy mo nitori ng refe rence 37 B7 0.
183 Parameter Instruction Code List Multi-s peed o peration 80 Multi -spee d setti ng (speed 8) 50 D0 0.01Hz 0 81 Multi -spee d setti ng (speed 9) 51 D1 0.01Hz 0 82 Multi -spee d setti ng (speed 10) 52 D2 0. 01Hz 0 83 Multi -spee d setti ng (speed 1 1 ) 53 D3 0.
184 Parameter Instruction Code L ist Additional function H6 (162) Automa tic rest art afte r instantane ous powe r failur e sele ction 3E BE 1 1 H7 (559) Second elec tron ic therma l O/L re lay 3B BB 0.01A 5 – b1 (5 60) Par ame ter for manufa ctur er sett ing.
185 Parameter Instruction Code List The parameter numbers in parentheses are those for use with the parameter unit (FR- PU04). * Though parameter setting by RS-485 communication can be made in the setting increments indicated in the table, note that the valid setting increment s are as indicated in the parameter list (p age 48).
REVI SION S *The manual number is given on the bott om left of t he back cover . Print Dat e * Manua l Number Revisi on Dec., 20 04 IB(N A)-0600 209ENG- A F irst edi tion.
Ein wichtiger Punkt beim Kauf des Geräts Mitsubishi Electronics FR-S500 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Mitsubishi Electronics FR-S500 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Mitsubishi Electronics FR-S500 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Mitsubishi Electronics FR-S500 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Mitsubishi Electronics FR-S500 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Mitsubishi Electronics FR-S500 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Mitsubishi Electronics FR-S500 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Mitsubishi Electronics FR-S500. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Mitsubishi Electronics FR-S500 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
