Benutzeranleitung / Produktwartung SD2100v2 des Produzenten Minelab
Zur Seite of 33
The Minelab SD2100v2 I N S T R U C T I O N M A N U A L MINELA B.
W ARNING THIS DOCUMENT CONT AINS MINELAB ELECTRONICS LIMITED RIGHTS TECHNICAL DA T A, OR RESTRICTED RIGHTS DA T A, OR BOTH. © Minelab Electronics Pty Limited This work is copyright.
The Minelab SD2100v2 Instruction Manual T able of Contents 1. Introduction ................................................................................................ 3 2. List of Parts ............................................................
Page 4 The Minelab SD2100v2 1. Introduction Thank you for purchasing the Minelab SD2100v2 . Y ou will find this detector to be one of the finest available for the detection of metallic objects in highly mineralised environments.
Instruction Manual Page 5 Figure 1 - SD2100v2 List of Parts.
Page 6 The Minelab SD2100v2 2 . List of Part s The SD2100v2 is packed in a single box containing the detector and an 1 1” Double ‘D’ coil . The following p art s are included (see Figure 1): Par t Item Number 1. 1 1” Double D Coil with Skidplate 2021-001 1 2.
Instruction Manual Page 7 3 . Unp acking and Assembly a) Place the two armrest halves (7) on either side of the shaft assembly (6) and ensure that the bolt holes line up. b) Slide two nylon bolts (8) through the holes and screw nylon wing nuts (9) onto the bolts with a couple of turns.
Page 8 The Minelab SD2100v2 j) Fit the battery (12) into the battery bag (13). k) Plug the headphones (17) into the socket in the cap of the battery . l) Put on the battery bag. Ensure that the Power switch on the control box is set to “Off”. Plug the connector on the battery cable into the power connector on the control box .
Instruction Manual Page 1 4. Control Box 4.1 Rear Panel Controls Power Switch The Power switch controls the power supply from the battery to the control box. Always switch the control box “Of f” before connecting or disconnecting the coil or battery , and when not in use.
Page 2 The Minelab SD2100v2 4.2 Front Panel Controls Search Switch Ground Balance mode ( Balance 1 and Balance 2 ) T o get the best results from your SD2100v2 it is import ant to know how different ground conditions affect the detecting process. The ground is made up of many different chemicals, minerals, salts, etc.
Instruction Manual Page 1 5. Operation The SD2100v2 does not have an external speaker . All sound is heard through the headphones , which plug into the headphone socket in the top of the battery pack. 5.1 Quick Start Instructions These instructions can be followed by operators who are familiar with the workings and general terminology of detectors.
Page 2 The Minelab SD2100v2 5.2 Operating Instructions 5.2.1 De tector Sounds Threshold: This is the background sound produced by the detector . The loudness of the background sound is set with the Threshold control. Set this so that you can just hear it.
Instruction Manual Page 3 Figure 5 - Ground Balancing 5.2.5 Set the T une Control With the SD2100v2 switched On and the Threshold control and T one control both set: a) Hold the coil vertical to the ground and at waist height, then move the coil slowly through a half circle.
Page 4 The Minelab SD2100v2 b) Adjust the Balance 1 control so that no variation in volume or pitch is heard as the coil is moved up and down. The greater the change in the volume or pitch of the threshold tone as the coil is moved above the ground, the further out of adjustment the balance controls are.
Instruction Manual Page 5 CAUTION Only use 6 volt batteries as recommended by Minelab. Never use a 12 volt battery as this will damage the detector . This damage is not covered by warranty .
Page 6 The Minelab SD2100v2 b) Plug the battery lead into the charger , then plug the mains charger into a mains outlet. Switch the mains outlet on. Check the charger nameplate; it will be rated at 1000 mAh or 500 mAh.
Instruction Manual Page 7 7. Detecting T echniques 7.1 Searching The SD2100v2 is a ‘motion’ detector , which means that it must be moving in relation to a target in order to detect it. DO NOT set your shaft length too short. If the coil is too close to your body it may detect your pick, the battery , or any other metal that you may be carrying.
Page 8 The Minelab SD2100v2 Each sweep should overlap the area covered by the previous sweep. This will ensure a full coverage of the searched area. Be aware of the search pattern of the coil and overlap your sweeps to take this into account.
Instruction Manual Page 9 7.3 Hints for Maximum Gold Recovery a) Keep the coil as close to the ground as possible. b) Listen very carefully . This is more import ant than concentrating on looking.
Page 10 The Minelab SD2100v2 7.5 Pinpointing In order to save time in the recovery of an object and to reduce the size of the hole required to extract it from the ground, it is necessary to pinpoint the exact location of the object.
Instruction Manual Page 11 7.6 Digging the T arget Once you have established the location of the target it is necessary to dig a small hole to recover it. In order to preserve the environment, it is essential to make the hole as small as possible and always replace any soil and grass that you have removed.
Page 12 The Minelab SD2100v2 NOTE: Always refill the hole you have dug, and leave the area as you found it. 7.6.1 Digging Deep T argets The SD2100v2 has unparalleled depth capabilities which will surprise experienced and new prospectors alike.
Instruction Manual Page 13 8. Maintenance The SD2100v2 is a high quality electronic instrument which is finely engineered and housed in a durable container . T aking care of it is common sense. · It is vitally important to keep all the connectors dry and clean.
Page 14 The Minelab SD2100v2 9. T roubleshooting Use the following table to check for problems which you can diagnose: If you need to return your detector to Minelab for service, please supply as many details as possible about the fault. This will enable our service engineers to rectify the fault quickly and efficiently .
Instruction Manual Page 15 10 . Specification NOTE: In the interest of product improvement, Minelab reserves the right to make changes to this specification without notice.
Page 16 The Minelab SD2100v2 1 1 . W arranty There is a two-year parts and labour warranty on the SD2100v2 control box. Refer to your Product W arranty card for details. Search coils are warranted for one year against malfunction. In all instances, refer to your supplier or Minelab for service, either in or out of warranty .
Instruction Manual Page 17 12. Accessories Figure 9 - Coil Search Patterns 12.1 Search Coils The SD2100v2 is supplied with the 1 1” Double ‘D’ as its st andard coil. Three other coils are available as accessories for use on the SD2100v2 — the 18”, 1 1”, and 8” Monoloop coils.
Page 18 The Minelab SD2100v2 Each Monoloop coil consists of only one coil of wire and gives a detection pattern similar to a concentric coil. Each Double ‘D’ coil contains two D-shaped coils of wire, which overlap and produce a ‘blade’ like detection pattern (see Figure 9).
Instruction Manual Page 19.
Page 20 The Minelab SD2100v2.
Instruction Manual Page 21.
Page 22 The Minelab SD2100v2.
Instruction Manual Page 23 Minelab Service Rep air Form T oday’ s Date: .................................................... Detector Model: ....................................... Serial No.: .............................. Purchased From: .........
Ein wichtiger Punkt beim Kauf des Geräts Minelab SD2100v2 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Minelab SD2100v2 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Minelab SD2100v2 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Minelab SD2100v2 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Minelab SD2100v2 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Minelab SD2100v2 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Minelab SD2100v2 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Minelab SD2100v2. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Minelab SD2100v2 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
