Benutzeranleitung / Produktwartung S-74D des Produzenten Miller Electric
Zur Seite of 36
S-74S, S-74D Processes Description MIG (GMA W) W elding Flux Cored (FCA W ) Welding (Gas- And Self-Shielded) Wire Feeder OM-1500-10 207 748K 2006 − 01 Visit our website at www.
Miller Electric manufactures a full line of welders and welding related equipment. For information on other quality Miller products, contact your local Miller distributor to receive the latest full line catalog or individual specification sheets. T o locate your nearest distributor or service agency call 1-800-4-A-Miller , or visit us at www .
T ABLE OF CONTENTS SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
dec_wire_6/05 Declaration of Conformity for European Community (CE) Products This information is provided for units with CE certification (see rating label on unit). NOTE Manufacturer : European Contact: Miller Electric Mg. Co. Mr . Danilo Fedolfi, 1635 W .
OM-1500-10 Page 1 SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING som _3/05 Y W arning: Protect yourself and others from injury — read and follow these precautions. 1-1. Symbol Usage Means W arning! W atch Out! There are possible hazards with this procedure! The possible hazards are shown in the adjoining symbols.
OM-1500-10 Page 2 Arc rays from the w elding process produce intense visible and invisible (ultraviolet and infrared) rays that can burn eyes and skin.
OM-1500-10 Page 3 1-3. Additional Symbols For Installation, Operation, And Maintenance FIRE OR EXPLOSION hazard. D Do not install or place unit on, over , or near combustible surfaces. D Do not install unit near flammables. D Do not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit.
OM-1500-10 Page 4 1-5. Principal Safety Standards Safety i n W elding, Cutting, and Allied Processes, ANSI Standard Z49.1, from Global Engineering Documents (phone: 1-877-413-5184, website: www .
OM-1500-10 Page 5 SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE A V ANT UTILISA TION som _3/05 Y A vertissement : se protéger et protéger les autres contre le risque de blessure — lire et respecter ces consignes.
OM-1500-10 Page 6 Le rayonnement de l’arc du procédé de soudage génère des rayons visibles et invisibles intenses (ultraviolets et infrarouges) susceptibles de provo- quer des brûlures dans les yeux et sur la peau. Des étincelles sont projetées pendant le soudage.
OM-1500-10 Page 7 2-3 . Dange rs suppléme ntaire s en r e lation avec l’installa tion, le f onctionne ment et l a maintena nce Risque D’INCENDIE OU D’EXPLO- SION. D Ne pas placer l’appareil sur , au-dessus ou à proximité de surfaces inflammables.
OM-1500-10 Page 8 2-5. Princi pales no rmes de sécurit é Safety in W elding, Cutting, and Allied Processes, ANSI Standard Z49.1, de Global Engineering Documents (téléphone : 1-877-413-5184, site In- ternet : www .
OM-1500-10 Page 9 SECTION 3 − DEFINITIONS 1 1.1 1.2 1.3 3 3.1 3.2 3.3 4 4.1 + 2 2.1 2.2 + + 56 + 2.3 S-178 936 A. W arning! Watch Out! There are possible hazards as shown by the symbols. B. Drive rolls can injure fingers. C. W elding wire and drive parts are at welding voltage during operation − keep hands and metal objects clear .
OM-1500-10 Page 10 ST-178 794-A 50/60 S/N: 24 10.0 Hz 50/60 IP 21 V 100 A 750 X 100 % V U 1 = A I 1 = 1 U 2 = I 2 = 3-2. Rating Label For CE Products For label location see Section 5-2. 3-3. Symbols And Definitions Some symbols are found only on CE products.
OM-1500-10 Page 1 1 SECTION 4 − INTRODUCTION 4-1. Specifications T ype of Input Power W elding Power Source T ype Wire Feed Speed Range Wire Diameter Range W elding Circuit Rating IP Rating Overall .
OM-1500-10 Page 12 5-2. Rear Panel Connections And Rotating Drive Assembly 802 824-A / 802 825-A 2 3 4 1 14-Pin Control Cable - 10 ft (3.0 m) 2 Shielding Gas V alve Fitting Connect customer-supplied gas hose with 5/8-18 right-hand threads. . Shielding gas pressure not to exceed 90 PSI (620 kPa).
OM-1500-10 Page 13 5-3. 14-Pin Plug PLG12 Information Pin* Pin Information A 24 volts ac with respect to socket G. A J K B Contact closure to A completes 24 volts ac contactor control circuit. A J B K I L G Circuit common for 24 volts ac circuit. C L N H D M G C +10 volts dc input from power source to wire feeder with respect to socket D.
OM-1500-10 Page 14 5-6. Installing And Threading W elding Wire Ref. 156 929-A / Ref. 150 922 / Ref. 156 930 / S-0627-A T ools Needed: . Be sure that outlet cable has proper size liner for the welding wire size. When installing gun, position liner (extending from outlet wire guide) as close a s possible to drive rolls without touching.
OM-1500-10 Page 15 5-7. Setting Internal DIP Switches Position Settings And Results For DIP Switch S1 On PC1 On = Current detect over- ride. For welding power sources that don’t provide current feedback through the 14-pin receptacle. Run- in is inactive.
OM-1500-10 Page 16 T ools Needed: 1/4 in 5-8. Equipment DIP Switch Settings (For Models With Meters Only) 12 3 45 Or Or High Speed Motor Meters/Minute High Speed Motor Inches/Minute Standard Motor Meters/Minute Standard Motor Inches/Minute Digital Meter Functions 12 3 45 12 3 45 12 3 45 Ref.
OM-1500-10 Page 17 SECTION 6 − OPERA TION 6-1. Power Switch 1 Power Switch 1 802 827-A 6-2. Jog/Purge 1 802 828-A 2 1 Jog/Purge Push Button 2 Wire Speed Control 3 Gun Trigger Receptacle Pressing the Jog/Purge switch al- lows the operator to jog wire without energizing the weld power or gas valve circuit.
OM-1500-10 Page 18 6-3. T rigger Hold Switch 1 T rigger Hold Switch Trigger hold allows the operator to weld with- out holding the gun trigger . • T o use the trigger hold function, place the trigger hold switch in the On position.
OM-1500-10 Page 19 SECTION 7 − MAINTENANCE 7-1. Routine Maintenance Y Disconnect power before maintaining. 3 Months Replace unreadable labels. Clean and tighten weld terminals. Repair or replace cracked weld cable. Check 14-pin cord. Check gas hose and fittings.
OM-1500-10 Page 20 7-2. Diagnostics • Error Indications Error conditions are indicated by LED3 on PC 1 or on display (on models with meters). T o view LED3, turn Off unit, remove wrapper , an d turn unit On. LED3 is most easily observed from the left side of the unit.
OM-1500-10 Page 21 7-3. T roubleshooting Y Disconnect power before troubleshooting T rouble Remedy Wire feeds, shielding gas flows, but electrode wire is not energized. Check cable connections. Check cables for continuity , and repair or replace cables if necessary (see Section 5-2).
OM-1500-10 Page 22 SECTION 8 − ELECTRICAL DIAGRAM Figure 8-1. Circuit Diagram 202 246-C.
OM-1500-10 Page 23 Notes.
OM-1500-10 Page 24 SECTION 9 − P ARTS LIST 802 943 . Hardware is common and not available unless listed. Fig 9-2 21 Fig 9-3 4 1 2 6 14 15 16 17 18 19 20 5 7 8 9 10 11 12 11 10 13 3 Figure 9-1.
OM-1500-10 Page 25 Item No. Item No. Part No. Description Quantity Figure 9-1. Main Assembly Part No. Description Quantity 1 159 647 Insulator , Motor Clamp 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-1500-10 Page 26 802 945-D . Hardware is common and not available unless listed. 2 5 6 7 8 9 8 7 10 11 12 13 14 15 16 17 18 19 20 23 24 25 26 27 22 28 4 21 3 1 29 Figure 9-2. Control Box Item No. S-74S S-74D Figure 9-2. Control Box (Figure 9-1 Item 21) Diagram marking Part No.
OM-1500-10 Page 27 Item No. Diagram marking Part No. Description Quantity Model S-74S S-74D Figure 9-2. Control Box (Figure 9-1 Item 21) 21 213 134 Knob, Encoder 1.670 Dia X .250 Id Push On W/Spring 0 1 . . . . . . . . . . . . . . . . . . . . . . . . .
OM-1500-10 Page 28 See T able 9-1 For Drive Roll & Wire Guide Kits . Hardware is common and not available unless listed. 803 790-A 20 11 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 1 2 3 4 5 6 22 21 19 18 17 16 15 14 19 13 12 11 9 10 8 7 6 5 4 3 2 1 Figure 9-3.
OM-1500-10 Page 29 Item No. Diagram marking Part No. Description Quantity Model S-74S S-74D Figure 9-3. Drive Assembly , Wire (Continued) 203 631 Pressure Arm, S/L & V ert S/R 4 Roll (Consisting Of) 1 1 . . . . . . . . . . . . . . . . . . . . . . .
OM-1500-10 Page 30 UC-GROOVE T able 9-1. Drive Roll And Wire Guide Kits .023-.025 in. 0.6 mm 151 024 087 130 .030 in. 0.8 mm 151 025 053 695 .035 in. 0.9 mm 151 026 053 700 151 036 072 000 151 052 132 958 .045 in. 1.1/1.2 mm 151 027 053 697 151 037 053 701 151 053 132 957 151 070 083 489 .
Warranty Questions? Call 1-800-4-A-MILLER for your local Miller distributor. miller_warr 2006 − 01 Y our distributor also gives you ... Service Y ou always get the fast, reliable response you need. Most replacement parts can be in your hands in 24 hours.
PRINTED IN USA © 2006 Miller Electric Mfg. Co. 2006 − 01 Miller Elect ric Mfg. Co. An Illinois T ool W orks Compa ny 1635 West S pencer S treet Applet on, WI 5 4914 US A International He adquarters.
Ein wichtiger Punkt beim Kauf des Geräts Miller Electric S-74D (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Miller Electric S-74D noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Miller Electric S-74D - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Miller Electric S-74D reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Miller Electric S-74D erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Miller Electric S-74D besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Miller Electric S-74D verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Miller Electric S-74D. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Miller Electric S-74D gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
