Benutzeranleitung / Produktwartung 172 M-10 Gun des Produzenten Miller Electric
Zur Seite of 44
Millermatic Challen ger 172 And M-10 Gun Processes Description R MIG (GMA W) Flux Cored (FCAW) Wire Feeder OM-1318 187923F March 2000 Visit our website at www.
Miller Electric manufactures a full line of welders and welding related equipment. For information on other quality Miller products, contact your local Miller distributor to receive the latest full line catalog or individual catalog sheets. T o locate your nearest distributor or service agency call 1-800-4-A-Miller , or visit us at www .
The following terms are used interchangeably throughout this manual: MIG = GMAW T ABLE OF CONTENTS SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1 . . . . . . . . . . .
.
OM-1318 Page 1 SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING som _nd_4/98 1-1. Symbol Usage Means W arning! W atch Out! There are possible hazards with this procedure! The possible hazards are shown in the adjoining symbols. Y Marks a special safety message.
OM-1318 Page 2 Arc rays from the welding process produce intense visible and invisible (ultraviolet and infrared) rays that can burn eyes and skin. Sparks fly of f from the weld. ARC RA YS can burn eyes and skin. D Wear a welding helmet fitted with a proper shade of filter to protect your face and eyes when welding or watching (see ANSI Z49.
OM-1318 Page 3 1-3. Additional Symbols For Installation, Operation, And Maintenance FIRE OR EXPLOSION hazard. D Do not install or place unit on, over , or near combustible surfaces. D Do not install unit near flammables. D Do not overload building wiring – be sure power supply system is properly sized, rated, and protected to handle this unit.
OM-1318 Page 4 1-5. EMF Information Considerations About W elding And The Ef fects Of Low Frequency Electric A n d M a g netic Fields W elding current, as it flows through welding cables, will cause electro- magnetic fields. There has been and still is some concern about such fields.
OM-1318 Page 5 SECTION 1 – CONSIGNES DE SECURITE – LIRE A V ANT UTILISA TION som _nd_fre 4/98 1-1. Signification des symboles Signifie Mise en garde ! Soyez vigilant ! Cette proc é dure pr é sente des risques de danger ! Ceux-ci sont identifi é s par des symboles adjacents aux directives.
OM-1318 Page 6 Le rayonnement de l ’ arc du proc é d é de soudage g é n è re des rayons visibles et invisibles intenses (ultraviolets et infrarouges) susceptibles de provoquer des br û lures dans les yeux et sur la peau. Des é tincelles sont projet é es pendant le soudage.
OM-1318 Page 7 1-3. Dangers suppl é mentaires en relation avec l ’ installation, le fonctionnement et la maintenance Risque D ’ INCENDIE OU D ’ EXPLOSION. D Ne pas placer l ’ appareil sur , au-dessus ou à proxi- mit é de surfaces infllammables.
OM-1318 Page 8 1-4. Principales normes de s é curit é Safety in W elding and Cutting, norme ANSI Z49.1, de l ’ American W el- ding Society , 550 N.W . Lejeune Rd, Miami FL 33126 Safety and Health Sandards, OSHA 29 CFR 1910, du Superintendent of Documents, U.
OM-1318 Page 9 SECTION 2 – SPECIFICA TIONS 2-1. Specifications Rated W elding Output Amperage Range Maximum Open- Circuit V oltage DC Amperes Input at Rated Load Output 230 V , 60 Hz, Single-Phase KV A KW W eight W/ Gun Overall Dimensions 130 A @ 20 V olts DC, 30% Duty Cycle 40 – 170 30 19.
OM-1318 Page 10 2-3. W elding Power Source Duty Cycle And Overheating Duty Cycle is percentage of 10 m i n- utes that unit can weld at rated load without overheating. If unit overheats, thermostat(s) opens, output stops, and cooling fan runs. W ait fifteen minutes for unit to cool.
OM-1318 Page 1 1 SECTION 3 – INST ALLA TION 3-1. Installing Work Clamp 1 Insulator 2 Bolt 3 Smaller Hole 4 W ork Clamp T ab s Bend tabs around work cable. 5 W ork Cable From Unit 6 Nut 1 2 3 4 5 6 Ref. ST-025 190-D T ools Nee d e d : 3/8, 7/16 in 3-2.
OM-1318 Page 12 3-3. Installing Gas Supply Obtain gas cylinder and chain to running gear , wall, or other station- ary support so cylinder cannot fall and break of f valve. 1 Cap 2 Cylinder V alve Remove c ap, stand to side of valve, and open valve slightly .
OM-1318 Page 13 3-4. Electrical Service Guide Input V oltage 230 Input Amperes At Rated Output 20 Max Recommended Standard Fuse Or Circuit Breaker Rating In Amperes Circuit Breaker 1 , Time-Delay 2 20.
OM-1318 Page 14 3-6. Installing Wire Spool And Adjusting Hub T ension S-0499 15/16 in Standard Wire Spool 1 Lb Wire Spool When a slight force is needed to turn spool, tension is set.
OM-1318 Page 15 3-7. Installing Drive Roll, Wire Guide And Threading Welding Wire 1 Drive roll Choose correct drive roll for wire type, and align drive roll with flat spot on shaft.
OM-1318 Page 16 3-8. W eld Parameter Material Thickness Wire T ype, Shielding Gas, And Flow Rate Wire Diameter (inch) Operator Controls 1/4 in (6.4 mm) 3/16 in (4.8 mm) 1/8 in (3.2 mm) 14 ga 16 ga 18 ga 20 ga 22 ga V oltage T a p* –– –– 3 3 2 2 1 1 .
OM-1318 Page 17 SECTION 4 – OPERATION 4-1. Controls 1 Wire Speed Control Use control to select a wire feed speed. A s V oltage switch setting in- creases, wire speed range also in- creases (see weld setting label in welding power source). Ref. ST-187 921 2 4 1 3 2 V oltage Switch .
OM-1318 Page 18 SECTION 5 – MAINTENANCE &TROUBLESHOOTING 5-1. Routine Maintenance Y Disconnect power before maintaining. 3 Months Replace unreadable labels. Repair or replace cracked weld cable. Clean and tighten weld terminals. 6 Months Blow out or vacuum inside.
OM-1318 Page 19 5-4. Cleaning Or Repairing Drive Assembly Y T urn Off power before cleaning or repairing drive assembly . 1 Wire Spool 2 Nozzle Cut welding wire off at nozzle. Re- tract wire onto spool and secure. 3 Pressure Roll Arm 4 Cotter Pin 5 Pin 6 Screw 7 Bearing Remove bearing.
OM-1318 Page 20 5-6. Cleaning Or Replacing Gun Liner Ref. ST-802 399-A 3/8 i n Y Disconnect gun from unit. T ools Needed: T o Reassemble Gun: Insert new liner . Install wire outlet guide so that 1/8 in (3 mm) of liner sticks out. Hand tighten outlet guide, and then tight- en two full turns more.
OM-1318 Page 21 5-7. Replacing Switch And/Or Head T ube Ref. ST-800 795-C 1 Remove handle locking nut. 2 Remove switch housing. Note : If installing new switch, push switch lead connectors onto terminal of new switch (polarity is not important). Install switch back into handle, and secure with handle locking nut.
OM-1318 Page 22 5-8. T roubleshooting T able T rouble Remedy No weld output; wire does not feed; fan Secure power cord plug in receptacle (see Section 3-5). does not run. Replace building line fuse or reset circuit breaker if open (see Section 3-5). Secure gun trigger plug in receptacle (see Section 3-2).
OM-1316 Page 23 SECTION 6 – ELECTRICAL DIAGRAM SB-210 034 Figure 6-1. Circuit Diagram.
OM-1318 Page 24 SECTION 7 – MIG WELDING (GMA W) GUIDELINES 7-1. T ypical MIG Process Connections Y W eld current can damage electronic parts in vehicles. Disconnect both battery cables before welding on a vehicle. Pla c e w o r k c l a m p a s close to the weld as possible.
OM-1318 Page 25 7-2. T ypical MIG Process Control Settings These settings are guidelines only . Material and wire type, joint design, fitup, position, shielding gas, etc. affect settings. T est welds to be sure they comply to specifications. NOTE 1/8 or .
OM-1318 Page 26 7-3. Holding And Positioning Welding Gun Welding wire is energized when gun trigger is pressed. Before lowering helmet and pressing trigger , be sure wire is no more than 1/2 in (13 mm) past end of nozzle, and tip of wire is positioned correctly on seam.
OM-1318 Page 27 7-4. Conditions That Affect Weld Bead Shape Weld bead shape depends on gun angle, direction of travel, electrode extension (stickout), travel speed, thickness of base metal, wire feed speed (weld current), and voltage.
OM-1318 Page 28 7-5. Gun Movement During Welding Normally , a single stringer bead is satisfactory for most narrow groove weld joints; however , for wide groove weld joints or bridging across gaps, a weave bead or multiple stringer beads works better .
OM-1318 Page 29 7-8. T roubleshooting – Excessive Spatter Excessive Spatter – scattering of molten metal particles that cool t o solid form near weld bead. S-0636 Possible Causes Corrective Actions Wire feed speed too high. Select lower wire feed speed.
OM-1318 Page 30 7-1 1. T roubleshooting – Lack Of Penetration Lack Of Penetration – shallow fusion between weld metal and base metal. Lack of Penetration Good Penetration S-0638 Possible Causes Corrective Actions Improper joint preparation. Material too thick.
OM-1318 Page 31 7-14. T roubleshooting – W aviness Of Bead W aviness O f Bead – weld metal that is not parallel and does not cover joint formed by base metal. S-0641 Possible Causes Corrective Actions W elding wire extends too far out of nozzle. Be sure welding wire extends not more than 1/2 in (13 mm) beyond nozzle.
OM-1318 Page 32 7-16. Common MIG Shielding Gases This is a general chart for common gases and where they are used. Many different combinations (mixtures) of shielding gases have been developed over the years. The most commonly used shielding gases are listed in the following table.
OM-1318 Page 33 Notes.
OM-1318 Page 34 SECTION 8 – P ARTS LIST . Hardware is common and not available unless listed. Figure 8-1.Complete Assembly 2 3 4 5 6 Includes Items 7 – 12 1 13 14 7 8 9 10 11 12 15 17 16 18 19 20 .
OM-1318 Page 35 Description Part No. Dia. Mkgs. Item No. Figure 8-1. Complete Assembly Quantity 1 126 838 DRIVE ASSEMBL Y , wire (consisting of) 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 090 416 PIN, hinge 1 .
OM-1318 Page 36 Description Part No. Dia. Mkgs. Item No. Figure 8-1. Complete Assembly Quantity 56 026 843 INSULA T OR, vinyl 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-1318 Page 37 Quantity Description Part No. Item No. Figure Figure 8-2. M-10 Gun 1 169 715 NOZZLE, slip type .500 orf flush 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ♦ 087 299 TIP , contact scr .
.
Warranty Questions? Call 1-800-4-A-MILLER for your local Miller distributor. miller_warr 7/00 Y our distributor also gives you ... Service Y ou always get the fast, reliable response you need. Most replacement parts can be in your hands in 24 hours. Support Need fast answers to the tough welding questions? Contact your distributor .
PRINTED IN USA 2000 Miller Electric Mfg. Co. 6/00 Miller Elect ric Mfg. Co. An I l li noi s T ool W orks Company 1635 W est S pencer Street Applet on, W I 5 4914 USA International He adquarte rs .
Ein wichtiger Punkt beim Kauf des Geräts Miller Electric 172 M-10 Gun (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Miller Electric 172 M-10 Gun noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Miller Electric 172 M-10 Gun - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Miller Electric 172 M-10 Gun reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Miller Electric 172 M-10 Gun erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Miller Electric 172 M-10 Gun besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Miller Electric 172 M-10 Gun verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Miller Electric 172 M-10 Gun. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Miller Electric 172 M-10 Gun gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
