Benutzeranleitung / Produktwartung W5748 des Produzenten Miele
Zur Seite of 68
Operating instructions for Washing machine W 5748 To avoid the risk of accidents or damage to the machine it is essential to read these instructions before it is installed and used for the first time.
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children.
Caring for our environment .........................................2 Warning and Safety instructions .....................................6 Operating the washing machine .....................................1 3 Control panel .........................
Detergent .......................................................3 2 The correct detergent ..............................................3 2 Water softener ....................................................3 4 Washing with several components .......
Removing the transit bars ...........................................5 0 Re-fitting the transit bars ............................................5 2 Levelling the machine ..............................................5 3 Screwing out and adjusting the feet .
This washing machine conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the washing machine, please read these instructions carefully before using it for the first time.
Safety with children ~ Children 8 years and older may use, clean or maintain the washing machine without supervision only if they have been shown how to do so in a safe way and understand the hazards involved. ~ Children under 8 years of age must be kept away from the machine unless they are constantly supervised.
Technical safety ~ Before setting up the washing machine, check it for any externally visible damage. Do not install or use a damaged washing machine. ~ Before connecting the washing machine, ensure that the connection data on the data plate (voltage and frequency) match the mains electricity supply.
~ Unauthorised repairs could result in unforeseen dangers for the user, for which Miele cannot accept liability. Repairs should only be undertaken by a Miele approved service technician. ~ If the connection cable is faulty it must only be replaced by a Miele approved service technician to protect the user from danger.
Correct use ~ Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen hoses may burst or split. The reliability of the electronic control unit may be impaired at temperatures below freezing point.
~ If the correct amount of detergent is dispensed, the machine should not need to be descaled. If, however, you do wish to descale the machine only use proprietary non-corrosive descaling agents and strictly observe the instructions on the packaging.
Accessories ~ Accessory parts may only be fitted when expressly approved by Miele. If other parts are used, guarantee, performance and product liability claims will be invalidated. Miele cannot be held liable for damage caused by non- compliance with these Warning and Safety instructions.
Control panel a Extra option buttons Various extra options can be added to the washing programmes. b Display See the following page for more information. c Temperature button For selecting a temperature. d Spin speed button For selecting the final spin speed or Rinse hold ( e ) or deselecting the spin ( No .
The following are selected via the display: – wash temperature – spin speed – programmable functions – cancellation of a programme – safety lock The display also shows: – the programme dur.
Before using the machine for the first time ensure that it is correctly installed and connected. See "Installation and connection". Also check that the drain filter is securely tightened to prevent the risk of water leaks during use.
Energy and water consumption – Water consumption and energy usage are determined by the size of the load. To make the most out of your machine, load the maximum dry load for the programme you are using. – When smaller amounts of laundry are washed, the automatic load recognition system will reduce the amount of water, time and energy used.
Brief instructions The headings numbered A , B , C ,... show the operating sequence and can be used as brief instructions. A Sort the laundry ^ Empty all pockets. , Foreign objects (e.g. nails, coins, paper clips, etc.) can cause damage to garments and components in the machine.
B Switch on the washing machine C Load the drum ^ Press the Door button to open the drum door. ^ Unfold the laundry and load loosely into the drum. Mixing both large and small items gives better wash results and also helps distribute the load evenly during spinning.
F Select an extra option(s) ^ Select an extra option by pressing the appropriate button. The relevant indicator light will come on to show which extra option has been selected. Not all the extra options are suitable for use with every programme. You can only select extra options which are compatible with the programme being used.
G Add detergent It is important to dispense the correct amount, becaus e... . . . too little detergent results in: – Laundry not getting properly clean and with time it may become grey and hard to the touch. – Greasy particles clinging to the laundry.
H Start the programme ^ Press the flashing Start/Stop button. The estimated programme duration will appear in the display once the programme has started. During the first 8 minutes the machine measures how much water is being absorbed by the laundry. The programme duration may be longer or shorter depending on this absorbency rate.
Final spin speed You can reduce the final spin speed. However, you cannot select a final spin speed higher than that shown in the chart above. Rinse and interim spin There is a spin after the main wash and between the rinses. A reduction in the final spin speed will also reduce the interim spin speed.
Programme chart 23 Cottons 9876 * cold to 90°C Max. load 7.0 kg Use for Cotton, linen or cotton mix fabrics, e.g. table linen, towelling, underwear, T-shirts etc.
Programme chart 24 Automatic plus 7621 * cold to 40°C Max. load 5.0 kg Use for Mixed loads of garments suitable for the Cottons and Minimum iron programmes.
Programme chart 25 Intensive plus cold to 90°C Max. load 7.0 kg Use for Mixed loads of heavily soiled garments suitable for the Cottons and Minimum iron programmes. Sort according to colour. Notes – The pre-wash additional function will be activated automatically.
The following extra options can be selected in addition to the programme: Short Water plus Pre-wash Pre-wash + Soak Extra quiet Cottons XXXXX Minimum iron XXXXX Delicates X X X X Woollens / X Proofing.
Washing The figure quoted in the bucket is the maximum temperature the garment can be washed at. The number of bars under the symbol indicates the level of agitation permitted.
Main wash Rinses Spinning Water level Wash rhythm Water level Rinses Interim spin Final spin Programme sequence 28 Cottons d a ( 2-4 1)2) LL Minimum iron ( c e 2-3 3) LL Delicates e d e 3 – L Woolle.
d = Low water level ( = Medium water level e = High water level a = Intensive rhythm b = Normal rhythm c = Gentle rhythm d = Sensitive rhythm e = Ultra sensitive rhythm f = Handwash rhythm This machine has fully electronic controls with automatic load recognition.
Cancelling a programme You can cancel a programme at any time after it has started. ^ Press the Start/Stop button. Cancel programme ^ Press the flashing Start/Stop button again. The suds will be pumped away. If you want to remove the laundry: ^ Press the Door button.
Adding or removing laundry after a programme has started ^ Press the Door button to open the drum door. ^ Add or remove items. ^ Close the drum door. The programme will continue automatically. Please note: Once a programme has started the machine cannot recognise any adjustment to the load.
The correct detergent All modern detergents produced for automatic washing machines are suitable. Use dispensing aids, e.g. balls, if these are supplied with the detergent. Tablets are suitable for full loads, but note that it may be impractical to reduce tablets for smaller loads.
Detergent 33 Universal detergent Detergent for coloureds Detergent for delicates Specialist detergent* Proofing agent** Fabric conditioner Cottons X X – – – X Delicates X X X – – X Woollens .
The right amount to dispense will depend on the following: – The quantity of laundry – The soiling level of the laundry Lightly soiled No visible dirt or stains. Possibly slight body odour. Normally soiled Visibly dirty and/or just a few slight stains.
Fabric conditioners and liquid starch Fabric conditioners make garments soft to handle and help prevent static cling when tumble drying. Starch stiffens and gives body to items of laundry, e.
A range of Miele branded cleaning and conditioning products is available to order from the Miele Spare Parts Department or via the internet at www.miele-shop.com Cleaning the drum (Hygiene info) Washing at low temperatures and/or using liquid detergent can cause bacteria and unpleasant smells to build up in the machine.
^ Clean the siphon. 1 . Remove the siphon from compartment § and rinse under hot running water. Clean the siphon tube in the same way. 2 . Replace the siphon. If starching frequently, thoroughly clean the siphon and siphon tube regularly. A build-up of starch will cause them to get clogged.
Cleaning the water inlet filters The washing machine has two filters to protect the inlet valves. These filters should be checked every six months or so, or more often if there are frequent interruptions to the water supply. To clean the filter in the union in the open end of the inlet hose: ^ First turn off the stopcock.
With the help of the following notes, minor faults in the performance of the machine, some of which may result from incorrect operation, can be put right without contacting the Service Department.
The following fault messages appear in the display and the programme stops Fault message Possible cause Remedy A ; Drain fault – The water outlet is blocked or restricted. – The drain hose has been fixed too high. – Clean the drain filter and the drain pump.
The following advice appears in the display Fault message Possible cause Remedy Chk detergent Excessive foam has built up during washing. Use less detergent next time and follow the manufacturer's instructions on dosage given on the packaging. Hygiene info A programme using a temperature above 60°C has not been run for a long time.
General problems Problem Possible cause Remedy The machine shakes during the spin cycle. The machine feet are not level. Level the machine (see "Installation and connection"). The laundry has not been spun properly and is still wet. The machine detected an imbalance during the final spin and reduced the spin speed automatically.
An unsatisfactory wash result Problem Possible cause Remedy Liquid detergent does not give the required result. Liquid detergents usually contain no bleaching agents. They do not remove fruit, coffee and tea stains. – Use a general purpose detergent containing a bleaching agent.
The drum door does not open when you press the Door button Possible cause Remedy The machine is not connected to the electricity supply and/or is not switched on. Insert the plug in the socket and switch on and/or switch the machine on with the K button.
Opening the drum door in the event of a blocked drain outlet and/or power failure ^ Switch the washing machine off. There is a lever behind the detergent drawer fascia panel. ^ Remove the lever. ^ Use it to open the access flap. Blocked drain outlet If the drain outlet is blocked, up to 25 litres of water will be retained in the machine.
Once the flow of water ceases: ^ Remove the drain filter completely. ^ Clean it thoroughly. ^ Remove any foreign objects (e.g. buttons, coins, etc.) and fluff from the filter housing. Turn the impeller by hand to check that it rotates freely. Any foreign object causing an obstruction should be removed.
In the event of any faults which you cannot remedy yourself, please contact: – your Miele Dealer or – Miele (see back cover for contact details). When contacting your Dealer or Miele, please quote the model and serial number of your machine, both of which are shown on the data plate visible above the porthole glass when the door is open.
Front view a Inlet hose (tested to withstand pressure of at least 7,000 kPa) b Electricity supply cable c - f Flexible drain hose (with detachable swivel elbow) g Control panel h Detergent dispenser d.
Rear view a Protruding lid for holding when moving the machine b Electricity supply cable c Inlet hose (tested to withstand pressure of at least 7,000 kPa) d Drain hose e Transport clip for inlet and drain hoses f Safety cap for transit bars g Transport clip for inlet and drain hoses and for storing transit bars when not in use.
Installation surface A concrete floor is the most suitable installation surface for a washing machine, being far less prone to vibration during the spin cycle than wooden floorboards or a carpeted surface. Please note: ^ The machine must be level and securely positioned.
^ Using the spanner supplied, turn the left-hand transit bar 90°, then ^ withdraw the transit bar. ^ Turn the right-hand transit bar 90°, then ^ withdraw the transit bar.
, To avoid the risk of injury the holes for the transit bars must be covered after the transit bars have been removed. ^ Plug the holes with the plastic caps as illustrated. ^ Secure the transit bars to the back of the washing machine. Make sure that the top catch is located above the holder.
Levelling the machine The machine must stand perfectly level on all four feet to ensure safe and proper operation. Incorrect installation may increase electricity and water consumption and may cause the machine to move about. Screwing out and adjusting the feet The four adjustable screw feet are used to level the machine.
The fitting of building-under kits* and stacking kits* must only be undertaken by qualified and competent persons, in accordance with the instructions supplied with the kit.
The Miele water protection system The Miele water protection system protects the washing machine from water damage. The system consists of three main components: 1) the inlet hose 2) the electronic unit and the washing machine housing 3) the drain hose 1) Inlet hose The inlet hose is tested to withstand pressure of more than 7,000 kPa.
Connection to the water supply The machine should be connected to a mains water supply in accordance with local and national safety regulations. The German authorities do not require it to have a non-return valve as the washing machine has been designed to comply with DIN regulations.
Connection to the drainage system The machine drains via a drain pump with a delivery head of 1 metre*. The drain hose must not be kinked as this restricts drainage. The swivel elbow at the end of the hose can be turned in either direction, or can be detached if required, with a sharp twist and pull.
Electrical connection U.K. All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with current national and local safety regulations (BS 7671 in the UK). Ensure power is not supplied to the appliance until after installation work has been carried out.
Consumption data 59 Load Consumption data Energy Water Duration Residual moisture in kWh in litres Cottons 90°C 7.0 kg 2.20 52 2 h 29 min 50% 60°C 7.0 kg 1.33 52 1 h 59 min 50% 60°C 3.5 kg 1.00 45 1 h 59 min 50% r * 7.0 kg 0.82 52 2h5 9m i n 50% r * 3.
Height 850 mm Width 595 mm Depth 615 mm Depth with door open 993 mm Height for building under 820 mm Width for building under 600 mm Depth for building under 600 mm Weight 98 kg Capacity 7 kg dry laun.
The programmable functions are used to alter the machine's electronics to suit changing requirements. Programmable functions can be altered at any time. To access programmable functions The programmable functions are accessed via the Start/Stop button and the programme selector.
Water plus This programmable function is used to select the water intake setting for the Water plus extra option. There are three different options: Water + (the machine is delivered with this option selected) The water level is increased in the wash and rinse stages.
Code A code can be used to lock the electronics on the washing machine to prevent it being used without your knowledge. When the code has been activated, you have to enter a code after switching the washing machine on. Otherwise the washing machine cannot be operated.
Temperature unit You can chose for the temperature to be displayed in °C/Celsius or °F/Fahrenheit . The machine is delivered with °C/Celsius as the default setting. Buzzer When the buzzer function has been activated, an audible tone sounds at the end of a programme or when Rinse hold is reached.
Standby display To save energy, the display goes out and the indicator light for the Start/ Stop button will start flashing slowly. The display will always go out, – if a programme is not selected within 10 minutes of the machine being switched on. – 10 minutes after the end of a programme.
Miele washing machines offer perfect care for your laundry and feature a wide range of special programmes designed to suit the fabric being washed. Miele have also developed a range of specialist CareCollection detergents and conditioning products to offer you a complete package for cleaning and caring for your laundry.
"UltraWhite" detergent This multi-purpose powder detergent has excellent stain removal properties and is suitable for white and light coloured laundry as well as heavily soiled coloured items. "UltraColor" detergent for coloured garments This liquid detergent is particularly suitable for cleaning coloured and dark garments.
Alteration rights reserved/4512/W 5748 M.-Nr. 09 493 480 / 00.
Ein wichtiger Punkt beim Kauf des Geräts Miele W5748 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Miele W5748 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Miele W5748 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Miele W5748 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Miele W5748 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Miele W5748 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Miele W5748 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Miele W5748. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Miele W5748 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
