Benutzeranleitung / Produktwartung W2888WPS des Produzenten Miele
Zur Seite of 76
Operating instructions f or W ashing machine W 2888 WPS T o avoid the risk of accidents or damage to the machine it is essential to read these instructions before it is installed and used for the first time.
Disposal of the packing material The transport and protective packing has been selected from materials which are envir onmentally friendly for disposal and can normally be recycled. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children.
Caring for our en vironment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Disposal of the packing material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Disposal of your old appliance or machine .
Changing the programme sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 T o cancel a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 T o interrupt a programme . . . . .
Installation and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Rear view . . .
T o avoid the risk of accidents and damage to the machine please read these instructions carefully befor e using it for the first time. They contain important infor mation on its safety , use and maintenance. Keep these operating instructions in a safe place and ensure that new users are familiar with the content.
The Miele "W ater protection system" protects fr om water damage provided the following conditions have been met: – the machine is correctly plumbed in and connected to the electricity supply . – if a fault has been identified, the machine must be examined by a competent person before further use, and repair ed if necessary .
If the correct amount of detergent is dispensed, the machine should not need to be descaled. If, however , you do wish to descale the machine only use proprietary non-corrosive descaling agents and strictly observe the instructions on the packaging. If in doubt, contact the Miele Customer Ser - vice Dept.
Control panel a Display See the following pages for more information. b Short cut buttons For selecting an individual washing programme quickly . These buttons can be programmed to select your own favourite wash programmes.
Displays Entry menu 1 COTTONS UNI. 60°C PROG. SELECTION ... 2 MINIMUM IRON 40°C SETTINGS F ... 3 DELICATES 40°C 4 WOOLLENS H 40°C 15:00 When the machine is switched on, the entry menu (with factory default settings) appears and Prog. Selection is highlighted.
Programme Selection men u PROGRAMME Back A SELECTION COTTONS HYG. COTTONS UNI. MINIMUM IRON H Y ou can use the multi-function selector to select any programme. The highlighting will move up or down depending on the direction the multi-function selector is turned in.
Before using the machine for the first time ensur e that it is correctly installed and connected. See "Installation and connection". Also check that the drain filter is securely tightened to prevent the risk of water leaks during use. The washing machine has a sensor which measures the amount of laundry in the drum.
Running your fir st programme 1 COTTONS UNI. 60°C PROG. SELECTION ... 2 MINIMUM IRON 40°C SETTINGS F ... 3 DELICATES 40°C 4 WOOLLENS H 40°C 15:00 ^ Press short cut button 1 . The main menu f or Cottons Universal appear s COTTONS UNI. 60°C 1800 rpm Duration: 1:06 h Extras H Timer Y H Detergent H Back A H ^ Press the flashing Start button.
Energy and water consumption – W ater consumption and energy usage are determined by the size of the load. T o make the most out of your machine load the maximum dry load for the programme you ar e using. – Use the Automatic and Quick wash programmes for small loads.
Brief instructions The headings numbered A , B , C , . . . show the operating sequence and can be used as brief instructions. A Sort the laundr y ^ Empty all pockets. , Foreign objects (e.g. nails, coins, paper clips, etc.) can cause damage to garments and components in the machine.
B Switch on the washing machine The interior drum lighting will come on. C Select a programme Y ou can select a programme either by: – using the appropriate short cut button to select one of the four frequently used pr ogrammes, or – by going into the Prog.
E Add deter gent The percentage amounts in the display will help you to add the correct percentage amount of detergent recommended by the manufactur er . 40% Add slightly less than half the amount recommende d... 50% Add half the amount recommende d..
F Start the programme ^ Press the flashing Start button. The estimated programme duration will appear in the display . This will count down in one minute steps. During the first 10 minutes the washing machine measures how much water is being absorbed by the laundry .
Y ou can programme the short cut buttons to call up the four wash programmes you use most fr equently . Y ou can do this at the same time as star ting a wash programme. Selecting/changing a fa v ourite ^ Switch the machine on. Entry menu 1 COTTONS UNI.
Important: If you do not make a selection in the sub-menu within approx. 20 seconds, the display will revert to the main menu. – T emperature selection COTTONS UNI. 60 °C 1800 rpm Temperature from Cold - 60°C a ^ Use the multi-function selector to select the temperature you want and confirm your selection.
Saving a fa v ourite programme All the settings you have selected are now shown in the main menu. COTTONS UNI. 40°C 1800 rpm Water plus Duration: 1:06 h Extras H Timer Y H Detergent H Back A H ^ Start the programme by pressing the Start button. In a few seconds the option Save will appear in the display above short cut button 3 .
Y ou can use the Extras to augment the basic wash programmes. T o open the Extras sub-men u COTTONS UNI. 60°C 1800 rpm Duration: 1:06 h Extras H Timer Y H Detergent H Back A H ^ Press short cut button 1 .
Rinse hold The laundry is not spun after the last rinse and remains suspended in the final rinse water . This reduces creasing if the laundry is not going to be removed from the drum imme - diately after the end of the programme. Soak For heavily soiled and stained items with protein stains (e.
The washing machine has a sensor which measures the amount of laundry placed in the drum. The Detergent sub-menu shows the percentage of the maximum load which has been placed in the drum. The maximum load will depend on the programme chosen. In addition to the load size percentage, the amount of detergent requir ed is also displayed as a % figure.
Y ou can use the timer to set the end time of a programme. Y ou can also delay the star t of a programme fr om 30 minutes up to a maximum of 24 hours, allowing you to make use of night-time economy electricity rates, for example. T o open the Timer sub-men u COTTONS UNI.
Final spin speed Programm U/min Cottons Hygiene 1800 Cottons Universal 1800 Minimum Iron 900 Delicates 600 Automatic 900 Quick wash 1600 Woollens 1200 Silks 400 Starch 1500 Separate rinse 1200 Spin 1800 Denim 900 Shirts 600 Outer wear 800 Y ou can reduce the final spin speed.
Cottons Hygiene 70°C to 95°C öF9 Fabric Cottons and linen fabrics, e.g. bed linen, table linen, nappies, underwear. Notes – Suitable for heavily soiled laundry. – For heavy soiling or where staining is visible, select Intensive . – For laundry with stubborn soiling and/or soiling which has been left unwashed for some time, select Soak .
Minimum iron cold to 60°C 67E81234 Fabric For garments made of synthetic fibres, mixed fibres and for easy care cotton shirts and blouses. Notes – For heavy soiling or where staining is visible, select Intensive .
Quick wash cold to 40°C 67 Fabric Small loads of lightly soiled laundry which can be washed in a Cottons Universal programme. Extras Water plus, Rinse hold Detergent Powder detergent, detergent for coloured fabrics, liquid detergent Max. load 2.5 kg Woollens / cold to 40°C ca Fabric Machine-washable or hand-washable wool or wool blend fabrics.
Spin For spinning fabrics. Please make sure you select the appropriate spin speed. Do not use for woollens. Denim cold to 40°C Fabric Denim fabrics, e.g. jeans, skirts, shirts. Notes – Wash dark garments inside out. – Denim often contains excess dye and will run during the first few washes.
Important - other care symbols / Hand wash (If no temperature is specified use the lowest temperature or cold) h Do not wash apf Dry clean D Do not dry clean y Suitable for chlorine bleaching z Do not.
Main wash Rinses Spinning Water level Wash rhythm Water level No of rinses Rinse and interim spin Final spin Cottons Hygiene d a ( 2-3 1) L 2) L Cottons Universal d a ( 2-3 1) L 2) Minimum iron d a e .
This washing machine has fully electronic contr ols with automatic load recognition. It takes in the right amount of water requir ed for the programme depending on the amount of laundry and its absorbency rate. This means that programme cycles and durations can vary .
T o cancel a programme COTTONS UNI. 60°C 1800 rpm WASHING 1:06 h Extras H Timer Y H Save H Cancel H Y ou can cancel a programme at any time after it has star ted by pressing short cut button 4 Cancel . The suds will be pumped away . ^ Open the drum door before starting a new programme.
Adding or remo ving laundry after a programme has started Laundry can be added or removed after the programme has started when using the following programmes: – Cottons Hygiene – Cottons Universal – Minimum iron – Quick wash – Automatic – Starch ^ Press the door button a to open the door .
Programme locking pr events the machine from being opened and/or the programme being cancelled during a wash programme. T o activ ate programme loc king ^ Once the programme has started, press the Sta.
All modern detergents produced for automatic washing machines are suitable, including liquid, compact (concentrated), tablets, liquid tablets and special application detergents. Use dispensing aids, e.g. balls, if these are supplied with the detergent.
Fabric conditioner s and liquid starc h Fabric conditioners make garments soft and fluffy to handle and help pr event static cling when tumble drying. Starch stif fens and gives body to items of laundry , e.g. shirts, tablecloths and bed linen. ^ Dispense according to the amount specified on the packaging.
, Disconnect the machine from the mains electricity supply and withdraw the plug from the socket prior to cleaning the machine. ^ Clean the casing with a mild non-abrasive detergent or soap and water . Wipe dr y with a soft cloth. ^ Clean the fascia panel with a damp cloth and wipe dry with a soft cloth.
Cleaning the detergent dispenser drawer Remove detergent residues r egularly . ^ Pull out the detergent dispenser drawer until a resistance is felt. Pr ess down the release catch and at the same time pull the drawer right out of the machine. ^ Clean the detergent drawer with warm water .
Cleaning the filter in the water inlet The washing machine has a filter to protect the water inlet valve. The accessible filter in the union in the open end of the inlet hose should be checked every six months, or more often if there ar e frequent interruptions to the external water supply .
What to do, if . . . With the help of the following notes, minor faults in the perfor mance of the appliance, some of which may result fr om incorrect operation, can be put right without contacting the Service Department.
Problems with the load size indicator Problem Possible cause Remedy The display indicates a load of < 25% even though the drum is full. There was already laundry in the drum when the washing machine was switched on. This has decalibrated the sensor from the zero setting.
General problems Problem Possible cause Remedy The machine shakes during the spin cycle. The machine feet are not level. Level the machine (see "Installation"). The pump makes strange noises. This is not a fault! These noises occur at the end of a pump sequence as a normal part of the operation.
An unsatisfactory wash result Problem Possible cause Remedy Liquid detergent does not give the required result. Liquid detergents usually contain no bleaching agents. They do not remove fruit, coffee and tea stains. – Use a general purpose detergent containing a bleaching agent.
The drum door cannot be opened by pressing the a button Possible cause Remedy The machine is not connected to the electricity supply and / or is not switched on. Insert the plug in the socket and switch on and / or switch the machine on with the s button.
Opening the drum door in the event of a b locked drain outlet and/or power failure ^ Switch the washing machine off. There is a lever behind the detergent drawer fascia panel. ^ Remove the lever . ^ Use it to open the access flap. Blocked drain outlet If the drain outlet is blocked, up to 25 litres of water will be r etained in the machine.
Once the flow of water ceases: ^ Remove the drain filter completely . ^ Clean it thoroughly . ^ Remove any foreign objects (e.g. buttons, coins, etc.) and fluff fr om the filter housing. T ur n the impeller by hand to check that it rotates fr eely . Any foreign object causing an obstruction should be removed.
Changing the lamp for the drum lighting The washing machine will still operate with no lamp in place or if the lighting is faulty . ^ Remove the yellow lever from behind the detergent drawer facia panel as described previously . ^ Switch the washing machine on and open the drum door .
In the event of any faults which you cannot remedy yourself, please contact: – your Miele dealer or – the Miele Service Department (see back cover for contact details).
Front vie w a Inlet hose with "W aterproof" system b Electricity supply cable c - f Flexible drain hose (with detachable swivel elbow) g Facia panel with controls h Detergent dispenser drawe.
Rear view a Protruding edge for holding when moving the machine b Electricity supply cable c Inlet hose with "W aterproof" system d Drainage hose e T ransit bar covers f Restraining clip for.
Installation surface A concrete floor is the most suitable installation surface for a washing machine, being far less prone to vibration during the spin cycle than wooden floorboards or a carpeted surface. Please note the following points: ^ The machine must be level and securely positioned.
^ Using the spanner supplied turn the left-hand transit bar 90°, then ^ withdraw the transit bar . ^ T ur n the right-hand transit bar 90°, then ^ withdraw the transit bar .
^ Fit the covers on to the two holes. Then plug the holes as shown with the caps. ^ Secure the transit bars to the back of the washing machine. Make sure that holes b are fitted over r etainers a . , The washing machine must not be moved without the transit bars in place.
Levelling the mac hine The machine must stand perfectly level on all four feet to ensure safe and proper operation. Incorrect installation may incr ease electricity and water consumption and may cause the machine to move about. False values may also show in the Load and Detergent display .
This washing machine is not suitable for building under a worktop. W asher and Dryer stack A Miele tumble dryer can be stacked with the washing machine. A stacking kit* is necessary and can be purchased from the Miele Spar e Parts Department. Please note: a Safety distance to wall: at least 2 cm b Height: Stacking kit with pull-out shelf: approx.
The Miele W aterproof system The Miele W aterproof system pr otects the washing machine from water damage. The system consists of three main components: 1) the inlet hose 2) the electr onic unit and t.
Connection to the water supply , The plastic casing of the safety valve contains electrical components. The W aterproof system must only be connected to its own stopcock. It must not be connected to mixer taps or similar and must not be fitted in areas wher e there is the risk of water or other liquids reaching it.
Maintenance and care If you intend to unscrew the Miele W aterproof system hose fr om the stopcock it is essential to disconnect the machine from the electricity supply first.
Connection to the drainage system The machine drains via a drain pump with a delivery head of 1 metre*. The drain hose must not be kinked as this restricts drainage. The swivel elbow at the end of the hose can be turned in either direction, or can be detached if requir ed, with a sharp twist and pull.
Electrical connection U .K. All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with national and local safety regulations. Ensure power is not supplied to the appliance until after installation work has been carried out.
Load Consumption data Energy Water Duration in kWh in litres Normal Intensive Cottons Hygiene 95°C 5.0 kg 1.70 42 1 h 51 mins 2 h 06 mins Cottons Universal 60°C 1) 5.0 kg 0.85 42 – 1 h 59 mins 60°C 5.0 kg 0.85 42 1 h 30 mins 1 h 59 mins 40°C 1) 5.
Height 85.0 cm Width 59.5 cm Depth 58.0 cm Depth with door open 97.5 cm Weight 94 kg Maximum floor load 1600 Newton (approx. 160 kg) Capacity 5 kg dry laundry Voltage see data plate Rated load see dat.
Settings menu J f or changing standard settings The Settings menu is used to alter the washing machine's electronics to suit changing requir ements.
T o open the Settings menu 1 COTTONS UNI. 60°C PROG. SELECTION ... 2 MINIMUM IRON 40°C SETTINGS F ... 3 DELICATES 40°C 4 WOOLLENS H 40°C 15:00 ^ Select Settings J from the entry menu and confirm your selection with the multi-function selector . Select Settings SETTINGS Back A LANGUAGE F .
Time of day First select either a 24 hour or 12 hour clock. Then set the current time of day . T o select a 24 hour or 12 hour c lock. SETTINGS Back A TIME OF DAY 24 h clock.. 12 h clock... ^ Select the clock option you want and confirm your selection.
W ater plus This setting is used to select the water intake setting for the W ater plus Extra option. There ar e three dif ferent options: W ater + The water intake is increased in the wash and rinse stages of the programmes (the washing machine is deliver ed with this setting programmed as standar d).
^ The washing machine is delivered with the Gentle action setting deactivated. A tick will appear beside the option to show that it has been set. SETTINGS Back A GENTLE ACTION Off B On ^ Select the option you want and confirm your selection.
Lock The system lock prevents your machine being used without your knowledge. When the system lock has been activated, you have to enter a code after switching the washing machine on. Otherwise the washing machine cannot be operated. T o activ ate the lock SETTINGS Back A LOCK Activate .
After the last number has been entered, you must confirm the code with OK. 125 Confirm lock code. OK H Back A H ^ Confirm lock code by pressing short cut button 1 . X Entry OK. Lock active when machine is switched off. ^ Switch the washing machine off.
T emperature Y ou can chose for the temperature to be displayed as °C/Celsius or °F/Fahrenheit . A tick will appear beside the option to show that it has been set. SETTINGS Back A TEMPERATURE °C / Celsius B °F / Fahrenheit ^ Select the option you want and confirm your selection.
Ke ypad tones An audible tone sounds when the Start button, a short cut button or the multi-function selector is pressed. The washing machine is delivered with the keypad tone switched off. A tick will appear beside the option to show that it has been set.
Stand-by T o save energy , the display goes out after 10 minutes and the Start button flashes slowly . There ar e two options: On Stand-by comes on: – if a programme is not selected after the machine has been switched on. – after a programme has started.
Memory If an Extra has been selected for a programme, or the recommended temperatur e or spin speed has been altered, the machine will stor e the changes in memory at the start of a programme. The next time this programme is selected these settings will appear in the Programme selection menu.
Alteration rights reserved/1405/W 2888 M.-Nr . 06 559 470 / 00 e n-G B.
Ein wichtiger Punkt beim Kauf des Geräts Miele W2888WPS (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Miele W2888WPS noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Miele W2888WPS - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Miele W2888WPS reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Miele W2888WPS erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Miele W2888WPS besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Miele W2888WPS verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Miele W2888WPS. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Miele W2888WPS gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
