Benutzeranleitung / Produktwartung K1811VI des Produzenten Miele
Zur Seite of 64
Operating and Installation Instructions Refrigerator K 1801 Vi K 1811 Vi K 1901 Vi K 1911 Vi To prevent accidents and appliance damage read these instructions before installation or use.
IMPORTANT SAFETY INSTRUCTIONS .................................4 Guide to the refrigerator ............................................7 Before use .......................................................9 Turning the appliance On/Off .................
Installation ......................................................3 5 Installation site ....................................................3 5 Custom door panels ...............................................3 7 Installation options ...............
When using the appliance, follow basic safety precautions, including the following: Read all instructions before installation and use to prevent accidents and machine damage. This appliance is intended for residential use only. Use only as described in this Operating manual.
Installation This appliance is top-heavy and must be secured to prevent the possibility of tipping forward. Keep the door closed until the appliance is completely installed and secured per the installation instructions. ~ This appliance must be installed and connected in compliance with the installation instructions.
Disposal of your old appliance ~ Before disposing of an old appliance, first make the door latch or lock unusable. ~ Take off the door. ~ Leave the shelves in place so that children may not easily climb inside. ~ Consult with your municipal policy on recycling.
a Hinged door shelf b Shelves (height adjustable) c Door shelves (height adjustable) d Deli drawer e Control panel f Main switch g Humidity filters h SmartFresh drawers Guide to the refrigerator 7.
Control panel a Access button " p " activates the control panel b Refrigerator c Upper SmartFresh drawer d Lower SmartFresh drawer e Temperature display X colder; Y warmer Allows you to set .
Before using for the first time ^ Clean the inside of the appliance and the accessories with a mild solution of warm water and liquid dish soap. Dry with a soft cloth. After installing the appliance, wait at least 30 minutes before switching on the appliance.
Using the settings When a sensor button has been selected with a finger touch, it will appear yellow. A de-selected button will appear white. ^ Touch the access button " p "s oi t turns yellow. On the control panel you will now see the sensor buttons for the three appliance zones.
Custom settings In the custom settings mode you can select and change functions. The function possibilities are described in the respective chapters of this manual.
^ By touching the X button, you can choose between: = 0 : Button sound is off = 1 : Button sound is on = – : Return to menu. ^ Touch the access button " p "t o confirm the setting. ^ Tap the X button until you see ; in the display. ^ Touch the access button " p ".
The appliance is equipped with an alarm system, to ensure that the temperature does not rise unnoticed because of energy loss or an open door. The alarm system is always operational, it does not need to be switched on. Temperature alarm If the temperature becomes too warm, an alarm sounds, the "alarm" indicator turns red and flashes.
Setting the temperature in the refrigerator ^ Touch the access button " p "s oi t turns yellow. ^ Touch the sensor button for the refrigerator so it turns yellow. ^ Use the X and Y buttons next to the temperature display to set the temperature warmer or colder.
Temperature unit (Fahrenheit/Celsius) The temperature can be displayed in degrees Fahrenheit (°F) or Celsius (°C). ^ Touch the access button " p "s oi t turns yellow. ^ Touch the sensor button for the refrigerator section so it turns yellow.
The SmartFresh drawers provide the right combination of temperature and humidity. The result is freshness up to three times longer than in the other zones of the refrigerator. Storage temperatures For fresh foods that are not adversely affected by cold, the best range is 32° - 37°F (0° - 3°C).
For optimal storage conditions, it is always best to store similar foods together in one drawer. The upper SmartFresh drawer is the best place to store moisture sensitive foods. Foods that are best stored under dry conditions – fresh fish and shellfish, meats, poultry, sausage, dairy products and deli salads.
Different storage zones Due to the natural circulation of air in the appliance, there are different temperature zones in the refrigerator. Cold, heavy air sinks to the lowest section of the appliance. Make use of these different zones when placing food in the appliance.
When the SuperCool function is activated, the appliance is cooled as cold and quickly as possible (to a factory-preset temperature). The SuperCool function is ideal for the rapid cooling of drinks and for refrigerating large quantities of foods. Switching on SuperCool ^ Touch the sensor button for the refrigerator so it turns yellow.
Refrigerator and SmartFresh drawers The refrigerator and SmartFresh drawers defrost automatically. During normal operation, condensate and frost can form on the rear wall of the refrigerator and drawers. You do not need to remove this build-up, it will defrost and evaporate automatically with the heat generated by the appliance.
Moving the shelves The shelves can be adjusted according to the height of the food. ^ Using both hands, grasp the shelf from underneath and lift slightly so that the rear of the shelf is slightly above the mountings. ^ Pull the shelf forward. ^ Move the shelf to the desired height, then insert the (rear) hooks into place.
SmartFresh drawer These drawers are set on telescopic tracks. They can be pulled in and out for loading and unloading, or removed for cleaning. ^ Open the drawer. On the hinged side of the door is a safety lock, which must be turned to a horizontal position before the drawer can be removed.
Adjusting the door shelves For easier loading, unloading, and cleaning, the door shelves can be shifted or completely removed. ^ Using both hands, grasp the door shelf by the frame and tip it slightly forward. ^ Slide the tipped shelf up or down along the slide-rails, and click it into place with the lower hooks.
To reduce the risk of electrical shock, disconnect the appliance from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before maintenance. Never use cleaning agents containing abrasive substances such as sand, soda, acids, chlorides or chemical solvents.
Aluminum frames The shelf frames are made of aluminum. ^ Clean the frames with a mild solution of warm water and liquid dish soap. Aluminum is susceptible to scratches and nicks, treat with care. The aluminum frames may become discolored or otherwise altered if soiling is not cleaned away promptly.
Ventilation slits ^ Check the ventilation slits in the base panel regularly. Remove any dirt/dust with a vacuum cleaner or brush. Clean as needed. Door seals Do not use oil or grease on the door seals. This may cause the seals to deteriorate and become porous over time.
Changing the light bulb The lighting automatically switches off after the door has been open for approx. 5 minutes. This is not a fault. After the bulb has cooled for a short time it will turn on again. If the light does not come on when the door is opened briefly, the light bulb should be changed.
Side lighting ^ Turn the light cover counterclockwise and pull out. Never touch a halogen bulb with bare fingers. When inserting a glass halogen bulb, always hold with a soft cloth. ^ Pull the defective light bulb from the socket. ^ Place the new bulb in the socket.
With the aid of the following guide minor problems can be corrected without a ser - vice call. Repairs should only be carried out by a qualified and trained person in strict accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage and may void the warranty.
Issue Possible fault Solution The compressor kicks on very frequently and for too long. The ventilation slits are covered or dusty. Clean with a vacuum or brush. The door has been opened too frequently, or a large amount of fresh food has been put in at once.
The appliance is making noises. Issue Possible fault Solution Brrrrr... Humming noise made by the compressor. This noise can get louder for brief periods when the motor is switching on. These noises are not a fault. The noise of the compressor and the coolant circulating in the system is unavoidable.
In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting the Technical Service Department, please quote the model and serial number of your appliance given on the data plate inside the appliance.
Installation instructions To prevent accidents and machine damage read these instructions before installation or use..
Disposal of packing materials The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags, etc.
Have the appliance installed by a qualified technician, according to the enclosed installation instructions. , WARNING This appliance is top-heavy and must be secured to prevent it from tipping forward. Keep the door closed until the appliance is completely installed and secured as per the installation instructions.
Base A fully loaded appliance is very heavy. The load-bearing capacity of your floor must meet the following requirements: K 18X1 Vi ..........9 9 6l b s (452 kg) K 19X1 Vi ........ 1,191 lbs (540 kg) To ensure that the appliance is installed securely and functions properly, the base must be flat, level and made of a hard, rigid material.
Custom door panels This appliance is compatible with all styles and designs of kitchen cabinetry. The total weight of the decorative panel must not exceed the following: K 18X1 Vi ...........1 1 9l b s( 5 4k g ) K 19X1 Vi ............8 1l b s( 3 7k g ) Installation options There are many different installation options.
Installation with partition using the "Merging Kit" The minimum thickness of the partition is 5 / 8 " (16 mm). If there is a partition with a thickness from 5 / 8 " (16 mm) to 6 5 .
Adjusting the door opening angle (optional accessory) Depending on the installation site, it may be necessary to adjust the door opening angle to 90°.
Niche dimensions Niche width (A) K 18X1 Vi 30" (762 mm) K 19X1 Vi 36" (915 mm) Dimensions 40.
Power supply 1. Power supply A K 18X1 Vi 15" (381 mm) K 19X1 Vi 18" (458 mm) Door dimensions (open min. 90°) A K 18X1 Vi 32 5 / 8 " (829 mm) K 19X1 Vi 38 11 / 16 " (982 mm) Dimens.
Before you begin Read these instructions completely and carefully. Have the appliance installed by a qualified technician, according to the enclosed installation instructions. To reduce the risk of injury or damage to the product, two people should be used for installation.
Check the installation niche To ensure a safe, trouble-free installation and the best possible cosmetic result, check to be sure that the installation space complies with the installation requirements. ^ Check the base (see "Installation"). ^ Check the dimensions of the cavity.
^ Loosen the bracket that holds the appliance to the pallet. , Caution! The appliance is no longer secured and may be unstable. ^ From the rear of the appliance carefully lift it from the pallet. Once the appliance is on the ground it can be wheeled around.
If the indicator light does not come on, installation of the module was unsuccessful. In that case, repeat the process. If that does not correct the problem, contact Miele. ^ Pull the antenna d straight out. ^ Guide the cover b over the antenna d and screw on the cover.
Anti-tip brackets The anti-tip brackets help keep the appliance safely attached to the installation space, which helps prevent tipping. Two anti-tip brackets are recommended for each appliance or appliance combination (side-by-side). The distance " D " between the anti-tip brackets b is the width of the appliance.
Securing an alternative anti-tip device If the anti-tip brackets cannot be attached securely, an alternative anti-tip device can be used. Ensure that there is no "give" between the appliance and the anti-tip device. If possible, always screw the wooden beam to existing studs.
Sliding the appliance into the installation space ^ Unscrew the plinth. ^ To protect the corners of the installation space, attach the supplied edge protector a on both sides with adhesive tape. ^ Plug the appliance into the power outlet b . The plug of the appliance should be easily accessible after installation.
Aligning the appliance ^ Align the appliance with the custom front. The installation aids e have been designed for the following total thicknesses of custom doors: – 3 / 4 " (19 mm) –1 1 / 2 " (38 mm). Be sure to take into account the possible differing thicknesses of the custom door that is to be fitted subsequently.
Note: – Do not twist or jam the appliance inside the niche. When unscrewing the height-adjustable feet, proceed gradually, alternating between left and right. – The adjustment of the rear feet is aided if the appliance is lifted at the rear (tipped forward slightly).
If there is a fairly large gap above the appliance, cut a wooden beam to fit exactly and place it in the gap. ^ If necessary, shorten the filler strip j to the required height. ^ Place the 2 strips on top of each other k . ^ Insert the filler strip until you hear it click into place l .
Preparing the custom door ^ Open the appliance door. ^ Unscrew the installation supports n from the appliance door. ^ Loosen the remaining screws from the strips o on each side of the door , then remove. ^ Set aside the screws and side strips o - you will need them again later.
^ Mark the distance X on the back-side of the custom door. ^ Also calculate and mark the center of the custom door Y . ^ Remove the mounting frame from the appliance door and position it according to the markings on the custom door. ^ Pre-drill the holes.
Attaching and aligning the custom door front ^ Fit the door handle to the custom door. Note that the screws are applied from the reverse side. ^ Open the door and hang the custom door with the adjusting rail over the double-threaded bolts p . ^ Screw the nuts q a few turns onto the double-threaded bolts.
Attaching the lower bracket (Only for appliances using the "Front panel gap kit".) ^ Open the appliance door. ^ Screw on the lower brackets. Pre-drill holes in the custom door. The lower bracket corrects the side position of the door: ^ Loosen the screw.
Attaching the covers ^ To mount the cover strips on both sides of the door, click them into place from bottom to top, into the gap between the appliance door and the custom door. ^ Screw the brackets onto both sides of the appliance, to hold the cover strip.
Attaching the toe-kick cover The maximum height of the toe-kick cover is 4" (101 mm) from the top of the floor. Do not cover the ventilation slits in the plinth. Risk of damage to the appliance. ^ If required, cut the toe-kick cover to the required length and height.
Mounting the air separator The air separator keeps the supply and exhaust air separate. This prevents warm exhaust air from flowing into the machine, optimizing the energy performance of the unit. ^ If necessary, shorten the three parts of the air separator.
, Avoid the risk of electrical shock - Plug into a grounded 3-prong outlet. - Do not move the ground plug. - Do not use an adapter. - Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Improper connection of the equipment grounding conductor may result in electric shock.
Miele's RemoteVision Wi-Fi technology creates a 'virtual link' between your appliance and our monitoring center. If a fault occurs, Miele's client service center will be notified and contact you, or another trusted individual identified on your call roster, in order to gain access to your appliance to fix the problem.
Accessing the RemoteVision control panel ^ Touch the access button " p "s oi t turns yellow. ^ Touch the sensor button for the refrigerator section so it turns yellow. ^ Note the position of the X button, but do not touch. ^ Touch the access button " p " again so it turns white.
MasterCool control panel options for RemoteVision Status indicators Description of function Flashing ; ~ Module booting phase Flashing ; ‡ Not connected to network Flashing ; | Connection to network.
63.
Alteration rights reserved / 4209 K 1801 Vi, K 1811 Vi, K 1901 Vi, K 1911 Vi For the most updated manual see the Miele web site. M.-Nr. 07 682 410 / 02.
Ein wichtiger Punkt beim Kauf des Geräts Miele K1811VI (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Miele K1811VI noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Miele K1811VI - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Miele K1811VI reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Miele K1811VI erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Miele K1811VI besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Miele K1811VI verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Miele K1811VI. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Miele K1811VI gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
