Benutzeranleitung / Produktwartung DA 420 V des Produzenten Miele
Zur Seite of 36
Operating and installation instructions Cook er hoods D A 420 V , D A 420 V EXT D A 424 V , D A 424 V EXT T o avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed or used for the first time.
Caring for the en vir onment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 W arning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Modes of operation . . . . .
Disposal of the packing material The transport and protective packing has been selected from materials which are envir onmentally friendly for disposal, and can normally be recycled. Packaging e.g. cling film, polystyrene and plastic wrappings must be kept out of the reach of babies and young children.
This appliance complies with all relevant local and national safety requir ements. Inappropriate use can, however , lead to personal injury and damage to property . T o avoid the risk of accidents and damage to the appliance, please read these instructions car efully before using it for the first time.
The appliance is only completely isolated from the electricity supply when: – it is switched off at the isolator , – it is switched off at the wall socket and the plug withdrawn, – the fuse from.
Safety with children The appliance is only intended for use by adults who have read these instructions. Keep children well away from the appliance at all times and supervise them when you are using it.
Using at the same time as other heating appliances that depend on the air from the r oom W ar ning - danger of toxic fumes Great car e should be taken when using the cooker hood at the same time and in the same room or ar ea of the house as another heating appliance which depends on the air in the room.
One of the following technical measures may be necessary to ensure safe operation. – If the only way of ensuring adequate ventilation is via an open window , a window contact switch should be fitted to ensure that the cooker hood can only operate when the window is opened sufficiently .
The cooker hood works with . . . air extraction: The air is drawn in, cleaned by the grease filters and dir ected outside. The cooker hood is fitted with a non-return flap , which is closed when the cooker hood is switched off. No exchange of room air and outside air can take place.
Guide to the appliance 10.
a Cover plate b T elescopic tower c Canopy The canopy is not designed to be used as a shelf. d Grease filters e Charcoal filter Available as an optional accessory for recir culation mode (DA 420 V onl.
T o switc h the fan on ^ Press the On/Of f touch control. The fan runs at power level "II". The indicator lamp will come on. If the cooker hood has been connected to a window contact switch via the DSM 400 control module, then the fan cannot be switched on if the window is shut.
The indicator lamps for fan power levels I and IV will flash if the automatic switch-off of the Intensive setting is not activated. ^ Press the + touch contr ol to activate automatic switch-off. The indicator lamps for fan power levels I and IV will now light up constantly .
T o switc h the lighting on The hob lighting can be switched on and off independently of the fan. ^ Briefly press the lighting touch contr ol to switch on the hob lighting. The indicator lamp will come on. The lighting will switch on at maximum brightness.
Filter operating hours counter The number of hours the appliance has been in operation is stored in memory . The indicator lamp for the grease filter touch control will come on after 30 hours of operation. The grease filters must then be cleaned. Afterwards, the filter operating hours counter must be reset.
Filter operating hours counter Y ou can set the operating hours counter to suit the type of cooking you do. – Select a short time if you roast or fry a lot.
Setting and altering the char coal filter operating hours counter (with recir culation mode) The charcoal filter is needed for recir culation mode. The cooker hood is set at the factory for extraction mode. On delivery , the operating hours counter for the charcoal filter is set to unlimited .
Adjusting the height of the canopy The height adjustment feature on the canopy can be used to – – adapt the height of the hood to suit the installation conditions. – adjust the working area underneath the hood to the height of the user . – maximise vapour extraction by lowering the canopy during particularly intensive cooking.
Before carrying out any cleaning or maintenance work, disconnect the cooker hood from the mains supply . Ensure that: – it is switched off at the isolator , or – it is switched off at the wall soc.
Controls The controls may suf fer discolouration or damage if soiling is left on them for too long. Remove soiling straight away . Observe the General notes on cleaning earlier in this section. Do not use stainless steel cleaning agents on the controls.
^ After cleaning, leave the filters to dry on an absorbent surface before replacing them. ^ When removing the filters for cleaning, also clean off any r esidues of oil or fat from the now accessible housing to prevent the risk of these catching fire.
Always replace the char coal filter imme - diately if – the indicator lamp for the charcoal filter touch control lights up, or – if it is no longer effective in absorbing kitchen odours. It should, however , be replaced at least every 6 months. Used charcoal filters can be disposed of with the normal household waste.
Changing a halogen lamp Before any cleaning or maintenance work, the cooker hood must be disconnected from the mains supply . Ensure that, depending on connection: – it is switched of f at the isola.
DA 420 V (Ceiling fixing viewed from above) DA 424 V (Ceiling fixing viewed from above) 1) Alternative positions for feeding through the mains cable 2) For EXT appliances: Cut-out for feeding the connection cable through to an external motor , min.
Safety distance between hob and cooker hood (S) The minimum safety distances between the top of a cooker or hob and the bottom of the cooker hood are as follows, unless a gr eater distance is specifie.
Assembl y par ts 4 screws 8 x 60 mm with 4 washers and 4 plugs S 10 to secure the cover plate to the ceiling The screws and plugs ar e designed for use in concrete ceilings. For other types of construction, alternative suitable fixings will be requir ed.
All electrical work should be undertaken by a suitably qualified and competent person in strict accordance with curr ent national and local safety regulations (BS 7671 in the UK). Installation, repairs and other work by unqualified persons could be dangerous, for which the manufacturer cannot be held liable.
The Miele DSM 400 Control module can be used to combine the cooker hood with other components. It enables the following: Connection to a window contact switc h If adequate ventilation to the room can .
Connection to a light switc h The control module can be used to switch on the cooker hood lighting and also to dim it via a light switch in the house. Installation The control module is fitted in the tower after the cover plate has been unscrewed fr om the ceiling.
Important: T o avoid the danger of toxic fumes, please observe the W ar ning and Safety instructions. This is especially crucial when using the cooker hood at the same time as another heating appliance which relies on air fr om the same room. The cooker hood should be installed according to local and national building regulations.
Important: If the exhaust ducting is to run through rooms, ceiling space etc. wher e there may be great variations in temperatur e between the differ ent areas, the problem of condensation will need to be addressed. The exhaust ducting will need to be suitably insulated.
In the event of a fault which you cannot correct yourself, or if the appliance is under guarantee, please contact: – Y our Miele Dealer or – The Miele Service Department (see back cover for address). When contacting your Dealer or the Service Department, please quote the model and serial number of your appliance.
T otal connected load* . . . . . . . . . 280 W Fan motor* . . . . . . . . . . . . . . . . 200 W Hob lighting . . . . . . . . . . . . . 4 x 20 W V oltage . . . . . . . . . . . . . . . . . . AC 230 V Frequency . . . . . . . . . . . . . . . . . . 50 Hz Fuse rating (UK) .
34.
35.
Alteration rights reserved / 1006 M.-Nr . 06 740 240 / 01 e n-G B.
Ein wichtiger Punkt beim Kauf des Geräts Miele DA 420 V (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Miele DA 420 V noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Miele DA 420 V - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Miele DA 420 V reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Miele DA 420 V erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Miele DA 420 V besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Miele DA 420 V verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Miele DA 420 V. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Miele DA 420 V gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
