Benutzeranleitung / Produktwartung CS 1012 G des Produzenten Miele
Zur Seite of 52
Operating and installation instructions Gas hobs CS 1012 CS 1034 To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time.
D Das Gerät ist auch für den Gebrauch in anderen als auf dem Gerät angegebenen Bestimmungsländer zugelassen. Die landesspezifische Ausführung und die Anschlussart des Gerätes haben wesentlichen Einfluss auf den einwandfreien und sicheren Betrieb.
Gas-heated appliances Safety precautions to take if you smell gas ß Turn off the gas emergency control valve immediately. This is usually located near the gas meter. ß Eliminate all sources of ignition in a safe manner. Do not smoke, light cigarette lighters or matches.
Guide to the appliance .............................................6 CS 1012 ..........................................................6 CS 1034 ..........................................................7 Warning and safety instructions .............
Preparing the worktop .............................................3 4 Installation of several appliances ....................................3 5 Fitting the spring clamps and spacer bars ............................3 7 Installing / removing the appliance(s) .
CS 1012 a Extra large burner b Normal burner c Pan support d Symbols to indicate which gas burner the control is for e Display Display l In-operation indicator m Residual heat indicator Controls: f re.
CS 1034 a Large burner b Normal burner c Extra large burner d Normal burner e Pan supports f Symbols to indicate which gas burner the control is for g Display Display l In-operation indicator m Residu.
Burner n Burner cap o Burner head p Ignition safety device q Ignitor r Burner base Guide to the appliance 8.
This appliance complies with all relevant local and national safety requirements. Improper use can, however, present a risk of both personal injury and material damage. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before installation and using it for the first time.
Safety with children ~ This appliance is only intended for use by adults who have read these instructions. This appliance is not a toy! To avoid the risk of injury, keep children well away and do not allow them to play with it or use the controls. They will not understand the potential dangers posed by it.
Technical safety ~ Before installation, check the appliance for visible signs of damage. Under no circumstances should you use a damaged appliance. It could be dangerous.
~ During installation, maintenance and repair work, the appliance must be connected from the gas supply and mains electricity supply. ~ While the appliance is under guarantee, repairs should only be undertaken by a service technician authorised by Miele.
Correct use ~ The appliance gets hot when in use and remains hot for quite a while after it has been switched off. Do not touch it whilst it could still be hot. ~ If a cooker hood is installed above the gas hob, ensure that the burners are always covered with a pan when in use.
~ Ensure that the flames from the burner do not spread out beyond the base and up the sides of the pan. ~ Unless the pan manufacturer states that you can do so, do not use pans with very thin bases on this hob, and never heat up empty pans as they could get damaged.
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal, and should be recycled. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of babies and young children.
Please stick the extra data plate for the appliance supplied with this documentation in the space provided in the "After sales service" section of this booklet.
Rapid ignition system The appliance is supplied with a rapid ignition system with the following features: – Rapid ignition without pressing und holding the control – Automatic re-ignition Should the flame be extinguished by a gust of air, the burner will re-ignite automatically.
Switching on ^ To ignite the burner press the control knob down and turn it anti-clockwise to the large flame symbol. The ignitor will make a clicking sound and ignite the gas. Operating a control will automatically create a spark on every burner. This is quite normal and does not indicate a fault.
In-operation indicator and Residual heat indicator When a gas burner is switched on, the relevant in-operation indicator lights up. Once it has reached a certain temperature, the residual heat indicator also lights up. The in-operation indicator goes out when the gas burner is switched off.
Burner Min. pan base diameter in cm Normal burner 10 Large burner 12 Extra large burner 14 Max. diameter at top of pan in cm Normal burner 22 Large burner 24 Extra large burner 24 – Select pans which are suitable for the burner they are to be used on.
Thermo-electric ignition This appliance has a thermo-electric ignition safety device. If the flame goes out, for example if food has boiled over or if there is a sudden draught, and automatic re-ignition has been unsuccessful, the supply of gas to the burner will be cut off.
General notes , Under no circumstances use a steam cleaning appliance to clean this appliance. The steam could reach the electrical components and cause a short circuit. The appliance should be cleaned after each use. Let it cool down to room temperature.
Stainless steel surfaces Clean stainless steel surfaces using an E-Cloth or with a solution of warm water and a little washing-up liquid applied with a soft sponge.
Burner Do not clean any parts of the burner in a dishwasher. The burner should be dismantled and then cleaned by hand using a solution of warm water and a little washing-up liquid applied with a soft sponge. Parts of the burner that cannot be removed should be wiped clean with a damp cloth only.
, Repairs to the gas and electrical components of this appliance must only be carried out by a suitably qualified and competent person to ensure safety (Gas Safe registered in the UK). Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work.
... the gas flame suddenly looks different. Check whether the burner components are assembled correctly. ... the gas flame goes out during operation. Check whether the burner components are assembled correctly. .... the ignitor on the burner does not spark.
Miele branded cleaning and conditioning products are available for your appliance. These can be ordered via the internet on www.miele-shop.com or from the Miele Spare Parts Department (see back cover) or from your Miele dealer.
This appliance must be installed and connected to services in accordance with local and national safety and building regulations. Fit wall units and extractor hood before fitting the hob to avoid damaging the surface.
Safety distance above the hob A minimum safety distance must be maintained between this appliance and the cooker hood above it. See the cooker hood manufacturer's operating and installation instructions for details.
Safety distances to the sides of the hob Ideally the hob should be installed with plenty of space on either side. There may be a wall at the rear and a tall unit or wall at one side. On the other side, however, no unit or divider should stand higher than the hob (see illustrations).
Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut-out and any niche cladding to protect it from heat damage. If the niche cladding is made from a combustible material (e.
CS 1012 a Spring clamps b Front c Building-in depth d Building-in depth for the mains connection box with mains connection cable, L = 2000 mm e Building-in depth for the gas connection R 1/2 - ISO 7-1.
CS 1034 a Spring clamps b Front c Building-in depth d Building-in depth for the mains connection box with mains connection cable, L = 2000 mm e Building-in depth for the gas connection R 1/2 - ISO 7-1.
^ Make the worktop cut-out for one or more appliances as applicable. Remember to maintain the minimum safety distance from the back wall , as well as from any tall unit or side wall to the right or left of the hob. See "Safety instructions for installation".
When installing two or more appliances next to each other a spacer bar b must be used between each one. See “Fixing the spring clamps and spacer bars”. Worktop cut-out - two appliances Worktop cut-out - three appliances To calculate the cut-out width (D) required: Add up the widths of each appliance (e.
a Spring clamps b Spacer bars c Gap between spacer bar and worktop d Sealing strip The illustration shows a worktop cut-out with spring clamps a and spacer bars b for 3 appliances.
Wooden worktops ^ Position the spring clamps supplied a and spacer bars b on the top edge of the cut-out in the positions marked. ^ Secure the spring clamps and spacer bars with the 3.5 x 25 mm screws supplied. Granite and marble worktops The screws are not required for granite or marble worktops.
^ Apply silicone to the side edges and the lower edges of the spring clamps a and the spacer bars b . ^ Then fill gap e between the spacer bars and the worktop with silicone from the tube supplied.
Installing the appliance(s) ^ Feed the connection cable down through the cut-out. ^ Starting at the front, position the appliance in the worktop cut-out. ^ Using both hands, press down evenly on the sides of the appliance until it clicks into position.
Do not use any sealant unless expressly instructed to do so. The sealing strip under the edge of the top part of the appliance provides a sufficient seal for the worktop. Do not use sealant between the frame of the top part of the appliance and the worktop.
All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with current local and national safety regulations (BS 7671 in the UK). Installation, repairs and other work by unqualified persons could be dangerous.
Important The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective earthing system, which complies with current local and national safety regulations.
, Connection to the gas supply, or conversion from one type of gas to another, should only be undertaken by an approved and registered gas installer in strict accordance with local and national safety and building regulations (e.g. Gas Safe registered in the UK).
Connection The gas connection must be installed so that connection can be made either from inside or outside the kitchen unit, and the isolating valve must be easily accessible and visible (by opening one of the kitchen doors, if necessary). After installing the appliance the gas burners have to be set for local conditions.
, Connection to the gas supply, or conversion from one type of gas to another, should only be undertaken by an approved and registered gas installer in strict accordance with local and national safety and building regulations (e.g. Gas Safe registered in the UK).
CS 1034 Nominal rating at high setting Gas type kW Normal burner Natural gas H Liquid gas 1.60 1.60 / 116 g/h Large burner Natural gas H Liquid gas 2.50 2.10 / 153 g/h Extra large burner Natural gas H Liquid gas 3.00 2.50 / 182 g/h Total output Natural gas H Liquid gas 8.
Changing the jets Disconnect the gas hob from the mains electricity supply. Turn off the gas supply. To change the main jets ^ Remove the pan support, burner cap n and burner head o . ^ Using an M7 socket spanner, unscrew main jet s . ^ Change the main jet.
Function test Check all gas fittings for leaks. ^ Reassemble the appliance. ^ Check the burner flame by operating the burner. The flame must not go out on the lowest setting, or when the control is turned quickly from a high to a low setting. On the highest setting, the flame must have a distinctive and visible core.
In the event of any faults which you cannot remedy yourself, or if the appliance is under guarantee, please contact: – Your Miele dealer, or – the Miele Customer Contact Centre (see back cover for address). Please note that telephone calls may be monitored and recorded to improve our service.
50.
51.
Alteration rights reserved/ 1610 M.-Nr. 07 172 910 / 11.
Ein wichtiger Punkt beim Kauf des Geräts Miele CS 1012 G (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Miele CS 1012 G noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Miele CS 1012 G - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Miele CS 1012 G reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Miele CS 1012 G erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Miele CS 1012 G besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Miele CS 1012 G verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Miele CS 1012 G. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Miele CS 1012 G gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
