Benutzeranleitung / Produktwartung EX 1000 des Produzenten MGE UPS Systems
Zur Seite of 28
51031604EN/AA - Page 1 Installation and user manual Pulsar EX 700 / 1000 / 1500.
Page 2 - 51031604EN/AA Introduction Thank you for selecting an MGE UPS SYSTEMS product to protect your electrical equipment. The Pulsar EX range has been designed with the utmost care. We recommend that you take the time to read this manual to take full advantage of the many features of your UPS.
51031604EN/AA - Page 3 Safety Safety of persons Safety rules A UPS has its own internal power source (the battery). Consequently, the power outlets may be energised even if the UPS is disconnected from the AC-power source. Dangerous voltage levels are present within the UPS.
Page 4 - 51031604EN/AA Foreword Using this document Important instructions that must always be followed. Information, advice, help. Visual indication. Action. Audio indication. In the illustrations on the following pages, the symbols below are used: LED off.
51031604EN/AA - Page 5 Contents 1. Presentation 1.1 Pulsar EX range ............................................................................................................. ............. 7 T ower model ............................................
Page 6 - 51031604EN/AA Contents 3.4 Personalisation (optional) ........................................................................................................... 19 Function ....................................................................
51031604EN/AA - Page 7 1. Presentation 1.1 Pulsar EX range Tower model Rack model EX 700 / EX 1000 EX 1500 EX 700 EX 1000 EX 1500 Dimensions in mm (H x W x D) 235.5 x 145 x 400 235.5 x 145 x 505 Weight in kg 10 12 15 EX 700 Rack EX 1000 Rack EX 1500 Rack EX 700 Rack EX 1000 Rack EX 1500 Rack Dimensions in mm (H x W x D) 88 (2U) x 482.
Page 8 - 51031604EN/AA 1 2 RS232 USB 1 2 RS232 USB 5 1. Presentation 1.2 Back Pulsar EX 1500 Pulsar EX 700 / Pulsar EX 1000 slot for communications-card option. RS232 communications port. USB communications port. four outlets for direct connection of protected equipment.
51031604EN/AA - Page 9 1 2 RS232 USB 1. Presentation Pulsar EX 700 Rack / Pulsar EX 1000 Rack / Pulsar EX 1500 Rack 7 6 1 4 11 8 3 9 10 Rack model slot for communications-card option. RS232 communications port. USB communications port. four outlets for direct connection of protected equipment.
Page 10 - 51031604EN/AA 100% 80% 50% 20% test % % 1 2 by-pass 1.3 Control panel Alarms UPS overload. electronics fault. battery fault. hold down to display percent load: - lamp test or buzzer OFF. - forced transfer to bypass and back by pressing button 3 times in less than 5 seconds.
51031604EN/AA - Page 11 2. Installation 2.1 Unpacking and checks two cords for connection of the protected equipment. RS 232 communications cable. USB communications cable. "UPS Driver" diskette for UPS personalisation. "Solution Pac" CD ROM.
Page 12 - 51031604EN/AA 2. Installation 27 28 30 24 Rack model 24 29 EX1000 Rack ␣ 24 two cords for connection of the protected equipment. ␣ 25 RS 232 communications cable. ␣ 26 USB communications cable. ␣ 27 "UPS Driver" diskette for UPS personalisation.
51031604EN/AA - Page 13 2.2 Installation of the rack version 2. Installation Rack mounting diagram with rails. The rails and the necessary mounting hardware are supplied by MGE UPS SYSTEMS.
Page 14 - 51031604EN/AA 2. Installation 2.3 Connection to the RS 232 or USB communications port (optional) 1 - Connect the RS 232 25 or USB 26 communications cable to the serial port or the USB port on the computer. 2 - Connect the other end of the communications cable 25 or 26 to the RS 232 2 or USB 3 communications port on the UPS.
51031604EN/AA - Page 15 1 2 U-Talk USB 2.4 Installation of the communications-card option It is not necessary to shut down the UPS to install the communications card: 1 - Remove the slot 1 cover secured by two screws. 2 - Insert the card in the slot. 3 - Secure the card with the two screws.
Page 16 - 51031604EN/AA 1 2 ? p r e s s r e s e t 24 7 4 11 2. Installation 2.5 Connections Check that the indications on the rating plate on the back of the UPS correspond to your AC-power system and to the actual electrical consumption of all the equipment to be connected to the UPS.
51031604EN/AB - Page 17 3. Operation 3.1 Start-up 100% 80% 50% 20% test % % 1 2 bypass The protected equipment connected to the UPS can be energised, whether AC input power is available or not. 12 13 14 23 Caution: the AC input power source must be present when energising for the first time.
Page 18 - 51031604EN/AB 3. Operation 3.3 Operation on battery power (following failur e of AC input power) 1 2 bypass 1 2 bypass test % 1 2 bypass 22 Transfer to battery power The AC-power source is outside tolerances, LED 23 is ON, the buzzer beeps three times.
51031604EN/AB - Page 19 3. Operation 3.4 Personalisation (optional) Function Personalisable function Automatic start Cold start (battery power) Forced shutdown Sleep mode UPS ON / OFF via software Def.
Page 20 - 51031604EN/AB 3. Operation bypass Personalisable function Rated UPS voltage Rated UPS frequency UPS tolerance for AC-power source frequency Overload alarm threshold UPS restart following sho.
51031604EN/AB - Page 21 4. Maintenance 4.1 T roubleshooting Indication LED 12 flashes and the buzzer beeps. LED 14 flashes. The yellow LED ␣ 15 flashes, the red indicator light 10 behind the UPS comes on and the buzzer sounds continuously . Signification UPS overload.
Page 22 - 51031604EN/AB Troubleshooting requiring MGE UPS SYSTEMS after-sales support Indication LED 13 flashes and the buzzer sounds continuously. Signification UPS electronics have detected a UPS fault. Depending on the UPS personalisation parameters (see section 3.
51031604EN/AB - Page 23 A B A F G C D E 4.2 Replacement of the battery module 4. Maintenance Removal of battery module A - Press to open door. B - Slide the door open and remove it. C D E - Procedure to remove the protective cover. F - Disconnect the battery module.
Page 24 - 51031604EN/AB E F 4. Maintenance B A Rack model Removal of battery module A - Remove the two screws securing the door. B - Slide the door open and remove it. C - Unscrew the bar that holds the battery module in place. D - Remove the bar. E - Disconnect the battery module.
51031604EN/AB - Page 25 5. Environment This product has been designed to respect the environment: It does not contain CFCs or HCFCs. UPS recycling at the end of service life: MGE UPS SYSTEMS undertake.
Page 26 - 51031604EN/AB 6. Appendices 6.1 T echnical characteristics Operating conditions Relative humidity: 20 to 90% without condensation. Temperature: 0 to 40 ° C.
51031604EN/AB - Page 27 6. Appendices 6.2 Glossary Authorised voltage range for Upper and lower voltage thresholds within which the UPS can operate on the automatic transfer to bypass if fault or bypass in the event of a UPS fault or overload.
Page 28 - 51031604EN/AB 6. Appendices 6.3 Index A AC power Failure .................................................................... 18 Frequency tolerance ............................................... 20 Return ..................................
Ein wichtiger Punkt beim Kauf des Geräts MGE UPS Systems EX 1000 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie MGE UPS Systems EX 1000 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für MGE UPS Systems EX 1000 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von MGE UPS Systems EX 1000 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über MGE UPS Systems EX 1000 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon MGE UPS Systems EX 1000 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von MGE UPS Systems EX 1000 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit MGE UPS Systems EX 1000. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei MGE UPS Systems EX 1000 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
