Benutzeranleitung / Produktwartung 2200C des Produzenten MGE UPS Systems
Zur Seite of 28
34007532EN/AA - Page 1 www .mgeups.com MGE UPS SYSTEMS Installation and user manual Pulsar EX treme 2200C / 3200C T H E U N I N T E R R U P T I B L E P O W E R P R O V I D E R.
Page 2 - 34007532EN/AA Introduction Thank you for selecting an MGE UPS SYSTEMS product to protect your electrical equipment. The Pulsar EX treme C range has been designed with the utmost care. We recommend that you take the time to read this manual to take full advantage of the many features of your UPS.
34007532EN/AA - Page 3 Important instructions that must always be followed. Information, advice, help. Visual indication. Action. Audio indication. In the illustrations on the following pages, the symbols below are used: LED off. LED on. LED flashing.
Page 4 - 34007532EN/AA.
34007532EN/AA - Page 5 Contents 1. Presentation 1.1 Standard positions ....................................................................................................................... 7 Rack position ............................................
Page 6 - 34007532EN/AA Contents 4. Maintenance 4.1 T roubleshooting .......................................................................................................................... 20 4.2 Replacement of the battery module ...................
34007532EN/AA - Page 7 1. Presentation 1.1 Standard positions Rack position Tower position Pulsar EX treme 2200C : 35.3 Kg Pulsar EX treme 3200C : 35.7 Kg 654 mm 438 mm (19") 86.5 mm (2U) w w w . m g e u p s .c o m P U L S A R EX trem e 1 0 0 % 8 0 % 5 0 % 2 0 % t e s t % 1 2 % B Y P A S S P U L S A R E X tre m e w w w .
Page 8 - 34007532EN/AA 1. Presentation 1.2 Back Slot for communications-card option. RS232 communications port. USB communications port. Four outlets for direct connection of protected equipment. Two programmable outlets (outlet 1 and 2). Output circuit breakers.
34007532EN/AA - Page 9 1.3 Control panel Alarms Hold down to display percent load: ◗ Lamp test or buzzer OFF. ◗ Forced transfer to bypass and back by pressing button 3 times in less than 5 seconds. ON / OFF. % battery remaining 100% 80% 50% 20% 1.
Page 10 - 34007532EN/AA 2. Installation 2.1 Unpacking and parts check Cord for connection to the AC-power source for Pulsar EX treme 3200C versions only (for the Pulsar EX treme 2200C version, use the power cord of the protected equipment). Two cords for connection of the protected equipment.
34007532EN/AA - Page 11 2.2 Installation in rack position 2. Installation Follow steps 1 to 6 for rack mounting of the UPS on the rails. The rails and the necessary mounting hardware are supplied by MGE UPS SYSTEMS. Note for step 3: It is possible to adjust the positions of the front brackets.
Page 12 - 34007532EN/AA 2.3 Installation in tower position 2. Installation Connect the two supports for the upright position. P U L S A R EXtrem e P U L S A R EX trem e www.
34007532EN/AA - Page 13 2. Installation 2.4 Connection to the RS232 or USB communications port (optional) 1 - Connect the RS232 30 or USB 31 communications cable to the serial port or the USB port on the computer. 2 - Connect the other end of the communications cable 30 or 31 to the RS232 2 or USB 3 communications port on the UPS.
Page 14 - 34007532EN/AA 2. Installation 2.6 Connections Check that the indications on the rating plate on the back of the UPS correspond to your AC-power system and to the actual electrical consumption of all the equipment to be connected to the UPS. 1 - Remove the power cord supplying the equipment to be protected.
34007532EN/AA - Page 15 The protected equipment connected to the UPS can be energised, whether AC input power is available or not. 3. Operation 3.1 Start-up Caution : the AC input power source must be present when energising for the first time. Press the ON / OFF button 16 .
Page 16 - 34007532EN/AA 3. Operation 3.3 Operation on battery power (following failur e of AC input power) Transfer to battery power The AC-power source is outside tolerances, LED 17 is ON, the buzzer beeps three times. The equipment connected to the UPS is supplied by the battery.
34007532EN/AA - Page 17 3. Operation 3.4 Personalisation (optional) Function Personalisable function Automatic start Cold start (battery power) Forced shutdown Sleep mode UPS ON / OFF via software Def.
Page 18 - 34007532EN/AA 3. Operation Personalisable function Rated UPS voltage Frequency mode Rated UPS frequency UPS tolerance for AC-power source frequency Overload alarm threshold UPS restart follo.
34007532EN/AA - Page 19 3. Operation 3.6 UPS remote power of f Pulsar EX treme C is equipped with a remote power off function (RPO) that can cut power to all the devices connected to the UPS using a remote user-operated contact. The function is implemented by opening a contact connected to the two terminals of connector 12 on the back of the UPS.
Page 20 - 34007532EN/AA 4. Maintenance 4.1 T roubleshooting If any of LEDs 25 , 26 or 27 flash, there is a operating anomaly or an alarm. If a LED flashes, the bargraph data is no longer displayed. Indication LED 27 flashes and the buzzer beeps. LED 25 flashes and the buzzer beeps.
34007532EN/AA - Page 21 4. Maintenance Indication The outlets are not supplied with power , even though button 16 is ON (version 3200C only). LED 26 flashes and the buzzer sounds continuously . Signification One of the protection circuit breakers 6 for the outlets on the back of the UPS is open.
Page 22 - 34007532EN/AA 4.2 Replacement of the battery module 4. Maintenance Safety rules: Batteries constitute a danger (electrical shock, burns). The short-circuit current may be very high. Precautions must be taken for all handling: ◗ remove all watches, rings, bracelets and any other metal objects; ◗ use tools with insulated handles.
34007532EN/AA - Page 23 4. Maintenance E - Remove the screws for the battery cover. F - Remove the cover. Reinstallation of the battery module Carry out the above operation in reverse order. ◗ To maintain an identical level of performance and safety, use a battery module identical to that previously mounted in the UPS.
Page 24 - 34007532EN/AA 5. Environment This product has been designed to respect the environment: It does not contain CFCs or HCFCs. UPS recycling at the end of service life: MGE UPS SYSTEMS undertake.
34007532EN/AA - Page 25 6. Appendices 6.1 T echnical characteristics Rating AC input ◗ V oltage ◗ Frequency ◗ Power factor Output ◗ V oltage ◗ Frequency ◗ Harmonic distortion ◗ Overload .
Page 26 - 34007532EN/AA 6. Appendices 6.2 Glossary Authorised voltage range for Upper and lower voltage thresholds within which the UPS can operate on the automatic transfer to bypass if fault or bypass in the event of a UPS fault or overload.
34007532EN/AA - Page 27 6. Appendices 6.3 Index A Remote power off ........................................................... 19 Automatic bypass ................................................... 9-18-20 Automatic start ............................
Page 28 - 34007532EN/AA.
Ein wichtiger Punkt beim Kauf des Geräts MGE UPS Systems 2200C (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie MGE UPS Systems 2200C noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für MGE UPS Systems 2200C - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von MGE UPS Systems 2200C reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über MGE UPS Systems 2200C erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon MGE UPS Systems 2200C besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von MGE UPS Systems 2200C verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit MGE UPS Systems 2200C. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei MGE UPS Systems 2200C gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
