Benutzeranleitung / Produktwartung 2001 des Produzenten Mercury
Zur Seite of 280
Before driving Introduction 2 Instrumentation 6 Controls and features 21 Seating and safety restraints 1 13 Starting and driving Starting 143 Driving 148 Roadside emergencies 176 Servicing Maintenance and care 198 Capacities and specifications 246 Customer assistance 255 Reporting safety defects 267 Index 268 All rights reserved.
The following warning may be required by California law: CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
BREAKING-IN YOUR VEHICLE There are no particular breaking-in rules for your vehicle. During the first 1 600 km (1 000 miles) of driving, vary speeds frequently . This is necessary to give the moving parts a chance to break in. INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing.
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation W.
V ehicle Symbol Glossary Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void.
RSM SET ACC COAST OFF ON C 0 1 2 3 4 5 6 RPMx1000 ABS ! CHECK ENGINE FUEL RESET E F H H H SPEED CONT 4WD HIGH 4WD LOW O/D OFF L L 10 MPH 20 50 60 70 30 40 80 90 km/h 0 0 0 10 1 00 1 20 1 0 0 0 0 0 0 40 60 80 100 120 140 160 180 20 DOOR AJAR CHECK GAGE CHECK SUSP OFF OFF Headlamp control (pg.
PUSH OD ON/OFF OFF HI R. WIPE OFF A/C MAX A/C SCAN BASS TREB BAL FADE SIDE EJ REW FF 1 - 2 TAPE AMS VOL - PUSH ON SEEK TUNE AM FM CLK 12 3 456 FM1 ST HIGH 4x4 LOW AUTO Gearshift (includes overdrive button) (pg. 156) Electronic sound system (pg. 36) Rear wiper/washer control (pg.
W ARNING LIGHTS AND CHIMES Check engine Y our vehicle is equipped with a computer that monitors the engine’ s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II). This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards.
These temporary malfunctions can be corrected by filling the fuel tank with high quality fuel of the recommended octane and/or properly installing and securely tightening the gas cap. After three driving cycles without these or any other temporary malfunctions present, the Check Engine light should turn off.
Air bag readiness Momentarily illuminates when the ignition is turned ON. If the light fails to illuminate, continues to flash or remains on, have the system serviced immediately . Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts.
T urn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster , check for a burned-out turn signal bulb. Refer to Bulbs in the Maintenance and care chapter .
Four wheel drive low (if equipped) Momentarily illuminates when the ignition is turned to the ON/ST ART position. Illuminates when four -wheel drive low is engaged. If the light continues to flash have the system serviced. Four wheel drive high (if equipped) Momentarily illuminates when the ignition is turned to the ST ART position.
Speed control This light comes on when either the SET/ACCEL or RESUME controls are pressed. It turns off when the speed control OFF control is pressed, the brake or clutch (if equipped) is applied or the ignition is turned to the OFF position. Safety belt warning chime Sounds to remind you to fasten your safety belts.
GAUGES Speedometer Indicates the current vehicle speed. Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”).
Never remove the coolant reservoir cap while the engine is running or hot. This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate. Odometer Registers the total kilometers (miles) of the vehicle.
Battery voltage gauge This shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated by arrows), have the vehicle’ s electrical system checked as soon as possible.
The FUEL DOOR icon and arrow indicates which side of the vehicle the fuel filler door is located. MESSAGE CENTER (IF EQUIPPED) W ith the ignition in the ON position, the message center displays important vehicle information through a constant monitor of vehicle systems.
Fuel status Press once to display the approximate amount of fuel remaining in the fuel tank. Press again to display the approximate amount of fuel used since the system was last reset. Fuel economy Press to display your vehicle’ s average fuel economy in liters/100 km or (miles/gallons).
System check Press the system check control to display the status of the following systems: • engine oil life left • engine oil level • voltage level • engine coolant temperature • washer fluid level • fuel level The engine oil life left has two phases.
Oil change reset Press the OIL CHANGE RESET control to reset the oil life feature to 100% (or your personalized oil reset percentage) (at optimal driving conditions, 100% oil life is equivalent to a maximum of 12 000 kilometers [7 500 miles]). After you have the oil changed, you must press and hold the OIL CHANGE RESET control for five seconds.
HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. Foglamp control (if equipped) T urn on the low-beam headlamps or parking lamps and press the foglamp control to activate the foglamps.
Flash to pass Pull toward you to activate and release to deactivate. P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. • Rotate up to brighten. • Rotate down to dim. • Rotate to full up position (past detent) to turn on interior lamps.
Mode selector control Controls the direction of the airflow to the inside of the vehicle. The air conditioning compressor will operate in all modes except and . However , the air conditioning will only function if the outside temperature is about 6°C (43°F) or higher .
• (Floor and defrost)-Distributes outside air through the windshield defroster ducts and the floor ducts. Heating and air conditioning capabilities are provided in this mode.
windows open. This will force most of the hot, stale air out of the vehicle. Once the vehicle has been “aired out”, operate the climate control system as desired. • Do not put objects under the front seat that will interfere with the airflow to the back seats (if equipped).
Electronic Automatic T emperature Control (EA TC) system (if equipped) The EA TC system will maintain a selected temperature and automatically control airflow . Y ou can override automatic operation with any of the override controls, the fan speed control or the steering wheel controls.
When in AUTOMA TIC and weather conditions require heat, air will be sent to the floor . However , if the engine is not warm enough to provide heat, the fan will be at a low speed and the air will be directed to the windshield. In 3 1 ⁄ 2 minutes or less, the fan speed will start to increase and the airflow location will change to the floor area.
T emperature conversion Press MAX A/C and DEF at the same time (for one second) to switch between Fahrenheit and Celsius. If your vehicle has an English/Metric (E/M) control, this control will also change the temperature display . Fan speed ( ) When AUTOMA TIC is pressed, fan speed is adjusted automatically for existing conditions.
The air conditioning compressor will operate in all modes except FLOOR and VENT . It will also operate only when required when AUTOMA TIC has been selected. However , the air conditioning will only function if the outside temperature is about 6°C (43°F) or higher .
• OFF-Outside air is shut out and the fan will not operate. For short periods of time only , use this mode to reduce undesirable odors from entering the vehicle. Rear fan off Press REAR F AN OFF to turn off the rear console fan. This overrides the rear console fan speed control.
• Remove any snow , ice or leaves from the air intake area at the base of the windshield. • If your vehicle has been parked with the windows closed during hot weather , the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open.
T urn the fan speed control to the desired position. Select for air to flow through these vents: Select for air to flow through these vents: - VOLUME + MODE SEEK MEMORY SEEK – VOLUME + BAND MEMORY S.
REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog. • A small LED will illuminate when the rear defroster is activated. The ignition must be in the ON position to operate the rear window defroster .
T o help avoid personal injury , always use caution when in reverse and when using the reverse sensing system. This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle.
The reverse sensing system is automatically enabled when the gear selector is placed in R (Reverse) and the ignition is ON. A reverse sensing control allows the driver to disable the reverse sensing system only when the ignition is ON, and the gear selector is in R (Reverse).
USING YOUR AUDIO SYSTEM AM/FM stereo cassette V olume/power control Press the control to turn the audio system on or off. T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
AM/FM select The AM/FM select control works in radio and tape modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the AM control to select from AM selections, and press the FM control to select from FM1 or FM2 memory preset stations.
Scan function The scan function works in radio mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode. Radio station memory preset The radio is equipped with six station memory preset controls.
Treble adjust The treble adjust control allows you to increase or decrease the audio system’ s treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
Automatic Music Search The Automatic Music Search feature allows you to quickly locate the beginning of the tape selection being played or to skip to the next selection. T o activate the feature, momentarily depress the T APE AMS button. Then, press either REW (for the beginning of the current selection) or FF (to advance to the next selection).
Dolby T noise reduction Dolby t noise reduction operates only in tape mode. Dolby t noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) Dolby t noise reduction. Dolby t noise reduction is manufactured under license from Dolby t Laboratories Licensing Corporation.
T o set the minute, press and hold the CLK control and press the TUNE control: • to decrease minutes and • to increase minutes. The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time).
Premium AM/FM Stereo/Cassette/Single CD V olume/power control Press the control to turn the audio system on or off. Audio power can also be turned on by pressing the AM/FM select control or the tape/CD select control. Audio power is turned off by using the volume/power control.
If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio, tape and CD modes.
Tune adjust for CD changer (if equipped) • Press to select the previous disc in the CD changer . (Play will begin on the first track of the disc unless the CD changer is in shuffle mode. Refer to Shuffle feature for more information. Hold the control to continue reversing through the remaining discs.
Seek function for CD or CD changer (if equipped) • Press to seek to the previous track of the current disc. If a selection has been playing for three seconds or more and you press , the CD changer will replay that selection from the beginning. • Press to seek forward to the next track of the current disc.
Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to T une adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
T o deactivate autoset and return to your audio system’ s manually set memory stations, press the AUTO control again. Bass adjust The bass adjust control allows you to increase or decrease the audio system’ s bass output. Press the BASS control then press: • to decrease the bass output and • to increase the bass output.
Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control then press: • to shift sound to the left and • to shift sound to the right. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
W ith the dual media audio system, press the CD control to toggle between single CD and CD changer play (if equipped). Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur . Rewind The rewind control works in tape and CD modes.
Dolby T noise reduction Dolby t noise reduction operates in tape mode. Dolby t noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) the Dolby t noise reduction. Dolby t noise reduction is manufactured under license from Dolby t Laboratories Licensing Corporation.
Setting the clock T o set the hour , press and hold the CLK control and press SEEK: • to decrease hours and • to increase hours. T o set the minute, press and hold the CLK control and press TUNE: • to decrease minutes and • to increase minutes.
The CLK button will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for 10 seconds, when the radio is turned on, and then revert to clock information.
T o turn on the rear seat controls, press the memory preset controls 3 and 5 at the same time. The will appear in the display . Pressing 3 and 5 at the same time again will turn the rear seat controls off.
Turning the speakers on and of f Press to turn all speakers on or off. Using headphones Plug a 3.5 mm headphone (not included) into the jack. Press the speaker on/off control to operate the headphones. The rear speakers will cut out once the speaker on/off control is pressed.
Memory preset control Push the MEMORY control successively to allow rear seat passengers to scroll through the 6 memory presets in AM, FM1 or FM2. Push the MEMORY control in CD changer mode (if equipped) to advance to the next disc. Seek function • In radio mode, press to find the next listenable station down the frequency band.
MACH T Audio System with AM/FM Stereo/Cassette/Single CD V olume/power control Press the control to turn the audio system on or off. T urn control to raise or lower volume.
AM/FM select The AM/FM select control works in radio, tape and CD modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in tape mode Press this control to stop tape play and begin radio play .
Tune adjust for CD changer (if equipped) • Press to select the previous disc in the CD changer . (Play will begin on the first track of the disc unless the CD changer is in shuffle mode. Refer to Shuffle feature for more information. Hold the control to continue reversing through the disc.
Seek function for CD changer (if equipped) • Press to seek to the previous track of the current disc. If a selection has been playing for three seconds or more and you press , the CD changer will replay that selection from the beginning. • Press to seek forward to the next track of the current disc.
Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to T une adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
Bass adjust The bass adjust control allows you to increase or decrease the audio system’ s bass output. Press the BASS control then press: • to decrease bass output and • to increase bass output. Treble adjust The treble adjust control allows you to increase or decrease the audio system’ s treble output.
Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the F ADE control then press: • to shift sound to the front and • to shift sound to the rear .
Rewind The rewind control works in tape and CD modes. • In tape mode, radio play will continue until rewind is stopped (with the T APE control) or the beginning of the tape is reached. • In CD mode, pressing the REW control for less than three seconds results in slow rewind.
Dolby T noise reduction Dolby t noise reduction operates only in tape mode. Dolby t noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) Dolby t noise reduction. The Dolby t noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation.
Setting the clock Press the clock/RDS control until SELECT HOUR is displayed and press: • to decrease hours and • to increase hours. T o set the minute, press the clock/RDS control until SELECT MIN is displayed and press: • to decrease minutes and • to increase minutes.
Radio Data System (RDS) feature This feature allows your audio system to receive text information from RDS-equipped FM radio stations. Press and hold the control for three seconds to turn the feature on or off.
RDS select program type • Press the RDS control until FIND program type is displayed. • Use the SEL control to select the program type. W ith the feature on, use the SEEK or AUTOSET or SCAN contro.
• Use the SEL control to select TYPE, NAME, TEXT or NONE. When your radio is turned to a RDS station, RDS station TYPE, station NAME, or TEXT message will be displayed along with the frequency . Press SEL in order to scroll through the text messages.
If there is a discrepancy between the rear seat and the front audio controls, (such as both trying to listen to the same playing media), the front audio system will receive the desired selection. T o activate the Personal Audio System, press the speaker/headphone control.
Turning the speakers on and of f Press to turn all speakers on or off. Using headphones Plug a 3.5 mm headphone (not included) into the jack. Press the speaker on/off control to operate the headphones. The rear speakers will cut out once the speaker on/off control is pressed.
Memory preset control Push the MEMORY control successively to allow rear seat passengers to scroll through the 6 memory presets in AM, FM1 or FM2. Push the MEMORY control in CD changer mode (if equipped) to advance to the next disc. Seek function • In radio mode, press to find the next listenable station down the frequency band.
CD changer (if equipped) The CD changer is located in one of the following locations: • in the trunk • in the center console • under the driver’ s seat 1. Slide the door to access the CD changer magazine. 2. Press to eject the magazine. 3. T urn the magazine (A) over .
If you pull too hard on the disc holder , the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine while pressing on the lever (A). 5. Line up the CD with the groove of the disc holder .
The CD magazine may be inserted or ejected with the radio power off. ONL Y use the magazine supplied with the CD changer , other types will damage the unit. Keep the CD changer door closed. Coins and foreign objects will damage the CD player and void your audio system warranty .
• Do not insert more than one disc into each slot of the CD changer magazine. Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur .
• T errain. Hills, mountains and tall buildings between your vehicle’ s antenna and the radio station signal can cause FM reception problems. Static can be caused on AM stations by power lines, electric fences, traffic lights and thunderstorms. Moving away from an interfering structure (out of its “shadow”) returns your reception to normal.
3. OFF , shuts off the engine and all accessories without locking the steering wheel. 4. ON, all electrical circuits operational. W arning lights illuminated. Key position when driving. 5. ST ART , cranks the engine. Release the key as soon as the engine starts.
Once speed control is switched off, the previously programmed set speed will be erased. T o set a speed • Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph).
• Accelerate with your accelerator pedal. When the desired vehicle speed is reached, press and release SET/SET ACC/SET ACCEL. Y ou can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed.
Pressing OFF will erase the previously programmed set speed. T o return to a previously set speed • Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light This light comes on when either the SET ACCEL or RES controls are pressed.
TIL T STEERING WHEEL Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control to lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving.
Push (tap) the end of the stalk briefly for a single swipe (no wash). Push and hold for three swipes with wash. Push and hold for a longer wash (up to ten seconds). Speed dependent wipers When the windshield wiper control is set on the intermittent settings, speed-sensitive front wipers automatically adjust as the vehicle’ s speed changes.
STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allow you to operate some radio and climate control features. Radio control features • Press BAND/MODE to select AM, FM1, FM2, T APE or CD (if equipped). In Radio mode: • Press MEM/NEXT to select a preset station from memory .
OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’ s overhead console will vary according to your option package. Storage compartment (if equipped) Press the OPEN control to open the storage compartment. The door will open slightly and can be moved to full open.
• Place the provided height adaptors onto the back of the GARAGE control as needed. • Press the GARAGE control to activate the transmitter . Moon roof (if equipped) Y ou can move the moon roof back to open the glass panel or tilt up to ventilate the vehicle.
Do not let children play with the moon roof. They may seriously hurt themselves. Electronic compass/temperature display (if equipped) Outside air temperature The outside temperature display is contained in the overhead console. The temperature display can be turned off and on by pressing the MODE control on the overhead console.
Compass zone adjustment 1. Determine which magnetic zone you are in by referring to the zone map. 2. T urn ignition to the ON position. 3. Press and hold the MODE control until V AR appears in the display , then release. The display should show the current zone number .
Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines: • Press and hold the MODE control until CAL appears in the display (approximately eight seconds) and release.
Programming 1. Prepare for programming the HomeLink t Universal T ransceiver by erasing the three factory default codes by holding down the two outside buttons until the red light begins to flash after 20 seconds.
T o program your hand-held transmitters: • continue to hold the button on the HomeLink t Universal T ransceiver . • press and re-press the hand-held transmitter button every two seconds until the red light changes from a slow to a fast flash.
3. Press and release the programmed HomeLink t button. Press and release the HomeLink t button a second time to complete the training process. (Some garage door openers may require this procedure to be done a third time to complete the training). The 2nd or 3rd press from step 3 will activate the door .
Operating T ravelNote T T ravelNote t records and stores messages for up to three minutes in total length with simple controls. When you get an idea or remember something important while you’re driving, you don’t have to try to scribble it down or pull off the side of the road.
T o delete a message: 1. Press and release the DEL button while listening to a message or shortly after . The indicator light will flash green twice. 2. T o delete all recorded messages, simultaneously press and release the PLA Y and REC buttons at the same time.
4. The autolamp automatically turns the lamps on and off. The indicator light will illuminate when the headlamps turn on. AUTOMATIC DIMMING REAR VIEW MIRROR The autolamp/automatic dimming mirror is equipped with an automatic dimming feature.
One touch down • Press AUTO completely down and release quickly . The driver’ s window will open fully . Depress again to stop window operation. One touch down can be deactivated during operation by pushing down on the top part of the driver power window control.
CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door .
Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place.
Use only soft cups in the cupholder . Hard objects can injure you in a collision. Auxiliary power point The power point is an additional power source for electrical accessories.
CENTER ARMREST/REAR CUPHOLDER (IF EQUIPPED) Do not attempt to raise the console armrest when the rear cupholder is in use. If you find resistance when raising the armrest, make sure the cupholder is fully closed or else damage may occur to the armrest.
The liftgate door and window should be closed before driving your vehicle. If not, possible damage may occur to the liftgate door lift cylinders and attaching hardware. Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle.
1. Remove the shade from the vehicle and extend it with the smooth grain facing you. 2. W rap the vinyl around the roller tube twice. T uck the edges of the vinyl inside the end cap with each wrap. 3. Fold the edges of the vinyl towards the center , making sure that the edges clear the end cap slots.
Unlocking the doors Press this control to unlock the driver’ s door . The interior lamps will illuminate. Press the control a second time within five seconds to unlock all doors. Locking the doors Press this control to lock all doors. T o confirm all doors are closed and locked, press the control a second time within five seconds.
Memory seat feature (if equipped) The remote entry system can also control the memory seat feature. Press the control once to unlock the driver’ s door and move the memory seat feature to the corresponding memory position, just as if you had pressed the memory control in the vehicle.
Replacing the battery The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. T ypical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle.
Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure.
The battery saver will shut off the interior lamps 45 minutes after the ignition has been turned to the OFF position. Keyless entry system (if equipped) W ith the keyless entry keypad, you can: • lo.
If you wish to erase your personal code, use the following instructions: Erasing personal code 1. Enter the factory-set code. 2. Press 1/2 within five seconds of step 1. 3. Press the 7/8 and 9/0 controls at the same time within five seconds of step 2.
The autolock feature repeats when: • any door , except the drivers door , is opened then closed while the engine is running and • you put the vehicle in motion Deactivating autolock Before following the activation or deactivation procedures, make sure that the ignition is OFF and all vehicle doors and liftgate window are closed.
SECURILOCK Y PASSIVE ANTI-THEFT SYSTEM SecuriLock y passive anti-theft system is an engine immobilization system. This system prevents the engine from being started unless a coded key is used. The SecuriLock y passive anti-theft system is not compatible with non-Ford aftermarket remote start systems.
The SecuriLock y passive anti-theft system is not compatible with non-Ford (aftermarket) remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection.
Programming spare keys A maximum of eight keys can be coded to your vehicle. Only SecuriLock y keys can be used. T o program a coded key yourself, you will need two previously programmed coded keys (k.
SEA TING Adjustable head restraints (if equipped) Y our vehicle’ s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision.
Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’ s safety belt in the event of a collision. Lift handle to move seat forward or backward.
Reclining the seatback can reduce the effectiveness of the seat’ s safety belt in the event of a collision. The control is located on the outboard side of the seat cushion. Press front to raise or lower the front portion of the seat cushion. Press rear to raise or lower the rear portion of the seat cushion.
Using the manual lumbar support (if equipped) T urn the lumbar support control toward the front of vehicle to move the lumbar support forward for more direct support. T urn the lumbar support control toward the rear of vehicle to move the lumbar support back for less direct support.
T o return the seat to the upright position: • Press downward on the upper corner of the seatback and hold. • Pull the release handle upward to unlatch the seat. • Rotate the seatback upward until the seatback latches in the upright position. The seatback will click when it is locked into position.
All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an air bag SRS is provided. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
After any vehicle collision, the safety belt system at all outboard seating positions (except driver , which has no “automatic locking retractor” feature) must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is still functioning properly .
The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described b.
• Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Front safety belt height adjustment Y our vehicle has safety belt height adjustments for the driver and front passenger . Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o lower the shoulder belt height, push the button and slide the height adjuster down.
Safety belt warning light and indicator chime The seat belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position.
The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... Consider ... 9 Crashes are rare events 9 36 700 crashes occur every day . The more we drive, the more we are exposed to 9 rare 9 events, even for good drivers.
Reasons given... Consider ... 9 I have an air bag 9 Air bags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. 9 I’d rather be thrown clear 9 Not a good idea. People who are ejected are 40 times more likely to DIE.
1. T urn the ignition switch to the RUN (or ON) position. (DO NOT ST ART THE ENGINE) 2. W ait until the safety belt warning light turns off. (Approximately 1–2 minutes) • Steps 3–5 must be completed within 60 seconds or the procedure will have to be repeated.
recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However , if the collision was minor and a qualified technician finds that the belts do not show damage and continue to operate properly , they do not need to be replaced.
Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.
Do not put anything on or over the air bag module. Placing objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury . Do not attempt to service, repair , or modify the Air Bag Supplemental Restraint System or its fuses.
How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation.
Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately . If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
If any of these things happen, even intermittently , have the SRS serviced at your dealership or by a qualified technician immediately . Unless serviced, the system may not function properly in the event of a collision.
How does the side air bag system work? The side air bag system consists of the following: • An inflatable nylon bag (air bag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks. • A special seat cover designed to allow airbag deployment.
Several air bag system components get hot after inflation. Do not touch them after inflation. If the side air bag has deployed, the air bag will not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified technician in accordance with the vehicle service manual.
Disposal of air bags and air bag equipped vehicles (including pretensioners) For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician.
If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child’ s face or neck, the child should wear the lap and shoulder belt. Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit.
When installing a child safety seat: • Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter . • Use the correct safety belt buckle for that seating position (the buckle closest to the direction the tongue is coming from).
Installing child safety seats in combination lap and shoulder belt seating positions Air bags can kill or injure a child in a child seat. NEVER place a rear -facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat.
The rear seats of your vehicle are equipped with built-in tether strap anchors located behind the seats as described below . The tether anchors in your vehicle are located in the rear cargo area.
4. Clip the tether strap to the anchor . If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. 5. Refer to the Installing child safety seats in combination lap and shoulder belt seating positions section of this chapter for further instructions to secure the child safety seat.
PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
Important safety precautions A computer system controls the engine’ s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically , have the vehicle checked.
• steering wheel is turned when getting in or out of the vehicle Make sure the corresponding lights illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver’ s safety belt is fastened, the light may not illuminate.
Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater -defroster system to respond quickly . Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below .
Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air . Improve vehicle ventilation by keeping all air inlet vents clear of snow , leaves and other debris.
BRAKES Y our service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’ s brake system.
ABS warning lamp ABS The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced.
Parking brake Apply the parking brake whenever the vehicle is parked. T o set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released.
STEERING Y our vehicle is equipped with power steering. Power steering uses energy from the engine to help steer the vehicle. T o prevent damage to the power steering pump: • Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running.
The air suspension shut-off switch is located in the cargo area behind the left rear quarter trim panel. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Normal vehicle operation does not require any action by the driver .
Y our vehicle has the capability to haul more cargo and people than most passenger cars. Depending upon the type and placement of the load, hauling people and cargo may raise the center of gravity of the vehicle. Use extra caution while becoming familiar with your vehicle.
Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn off the ignition whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly .
N (Neutral) W ith the gearshift in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear . (Overdrive) The normal driving position for the best fuel economy . T ransmission operates in gears one through four .
2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. T ransmission operates only in Second gear . 1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive).
Understanding gearshift positions Hold the brake pedal down while you move the gearshift lever from P (Park) to another position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone.
(Overdrive) can be deactivated by pressing the transmission control switch on the end of the gearshift lever . The transmission control indicator light (TCIL) will illuminate on the instrument cluster .
Forced Downshifts T o gain acceleration in (Overdrive) or Drive (O/D OFF) when passing another vehicle, push the accelerator to the floor . The transmission will downshift to the appropriate gear: fourth, third, second or first gear .
Positions of the Control-T rac system The Control-T rac system functions in three modes: • The 4WD AUTO mode provides four -wheel drive with full power delivered to the rear axle, and to the front axle as required for increased traction.
If your vehicle is equipped with 4WDor A WD, a spare tire of a different size than the road tires should never be used. Such a tire could result in damage to driveline components and make the vehicle difficult to control.
Shifting from 4WD LOW to 4WD AUTO or 4WD HIGH 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral). 4. Move the 4WD control to the 4WD AUTO or 4WD HIGH position.
Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Do not reduce the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels.
When speed control is on and you are driving uphill, your vehicle speed may drop considerably , especially if you are carrying a heavy load. If vehicle speed drops more than 16 km/h (10 mph), the speed control will cancel automatically . Resume speed with accelerator pedal.
Driving off-road with A WD Y our vehicle is specially equipped for driving on sand, snow , mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles, both on and off the road. Maintain steering wheel control at all times, especially in rough terrain.
When driving through water , determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly . If the ignition system gets wet, the vehicle may stall. Once through water , always try the brakes. W et brakes do not stop the vehicle as effectively as dry brakes.
Automatic transmissions may shift frequently while driving up steep grades. Eliminate frequent shifting by shifting out of (Overdrive) into D (Drive). Driving on snow and ice An A WD vehicle has advantages over 2WD vehicles in snow and ice but can skid like any other vehicle.
• GVWR (Gross V ehicle W eight Rating): Maximum total weight of the base vehicle, passengers, optional equipment and cargo. The GVWR is specific to each vehicle and is listed on the Safety Certification Label on the driver’ s door pillar . • GA WR (Gross Axle W eight Rating): Carrying capacity for each axle system.
to the front of your vehicle, (potentially including weight added to the cab), the weight added should not exceed the front axle reserve capacity (F ARC). Additional frontal weight may be added to the front axle reserve capacity provided you limit your payload in other ways (i.
DRIVING THROUGH WATER Do not drive quickly through standing water , especially if the depth is unknown. T raction or brake capability may be limited and if the ignition system gets wet, your engine may stall. W ater may also enter your engine’ s air intake and severely damage your engine.
Do not exceed the maximum loads listed on the Safety Compliance Certification label. For load specification terms found on the label, refer to V ehicle loading in this chapter . Remember to figure in the tongue load of your loaded vehicle when figuring the total weight.
T owing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of control, and personal injury . Preparing to tow Use the proper equipment for towing a trailer , and make sure it is properly attached to your vehicle.
Trailer lamps T railer lamps are required on most towed vehicles. Make sure your trailer lamps conform to local and Federal regulations. See your dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps.
T railer towing tips • Practice turning, stopping and backing up before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached.
LUGGAGE RACK Maximum load is 75 kg (165 lbs), evenly distributed. If it is not possible to distribute the load, position it as far rearward as possible. Adjustable tie down loops (not equipped) must be used to secure the load. T o adjust cross-bar position: 1.
GETTING ROADSIDE ASSIST ANCE T o fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty .
Roadside coverage beyond basic warranty In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer .
RESETTING THE FUEL PUMP SHUT-OFF SWITCH FUEL RESET The fuel pump shut-off switch is a device intended to stop the electric fuel pump when your vehicle has been involved in a substantial jolt. After a collision, if the engine cranks but does not start, the fuel pump shut-off switch may have been activated.
FUSES AND RELA YS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Always replace a fuse with one that has the specified amperage rating.
Passenger compartment fuse panel The fuse panel is located on the left hand side of the instrument panel facing the driver’ s side door . Pull the panel cover outward to access the fuses. T o remove a fuse use the fuse puller tool provided on the fuse panel cover .
The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 7.5A Power Mirror Switch, Power Antenna, Memory Seat 2 7.5A Blower Motor Relay , Air Bag Diagnostic Monitor 3 7.5A Left Stop/T urn T railer T ow Connector 4 10A Left Headlamp 5 10A Data Link Connector (DLC) 6 7.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 11 7.5A Instrument Cluster 12 7.5A W asher Pump Relay , Rear W asher Pump Relay 13 20A Brake Pedal Position Switch, Brake Pressure Switch 14 10A 4 Wheel Anti-Lock Brake System (4W ABS) Module, 4W ABS Main Relay 15 7.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 32 10A Heated Mirror 33 15A Headlamps, Daytime Running Lamps (DRL) Module, Instrument Cluster 34 7.5A Rear Integrated Control Panel, CD 35 7.5A Rear Blower Motor (With EA TC) 36 7.
The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 60A** I/P Fuse Panel fuses 1, 9, and 13 2 40A** Blower Motor Relay 3 50A** 4 Wheel.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 4 15A* Fog Lamps and Daytime Running Lamps 5 — Not Used 6 10A* Powertrain Control Module 7 30A* 4 Wheel Anti-Lock System (4W AB.
CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily . Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Spare tire information Y our vehicle is equipped with a spare tire that must be used for emergencies only .
Stowing the spare tire 1. Lay the tire on the ground with the valve stem facing up. 2. Slide the wheel under the vehicle and install the retainer through the wheel center . 3. T urn the jack handle clockwise until the tire is raised to its original position underneath the vehicle.
3. Block the diagonally opposite wheel. 4. Use the tip of the lug wrench to remove any wheel trim. 5. Loosen each wheel lug nut, but do not remove them until the wheel is raised off the ground. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle.
• Front • Rear T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. • Never use the front or rear differential as a jacking point.
10. Lower the wheel by turning the jack handle counterclockwise. 11. Remove the jack and fully tighten the lug nuts in the order shown. 12. Stow the flat tire, jack and lug wrench. Make sure the jack is fastened so it does not rattle when you drive. 13.
Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its adaptive strategy . As a result of this, the transmission may shift firmly . This operation is considered normal and will not effect function or durability of the transmission.
2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery .
• Engines except 4.0L SOHC • 4.0L SOHC 5. Ensure that the cables are clear of fan blades, belts, moving parts of both engines, or any fuel delivery system parts.
Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.
• 4.0L SOHC 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’ s battery . + – + – + – + – Roadside emergencies 195.
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery .
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member , your roadside assistance center . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt.
SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a scheduled maintenance guide which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide the necessary parts and service.
Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the steering column on the instrument panel.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L SOHC V6 engine 1. W indshield washer fluid reservoir 2. Automatic transmission fluid dipstick 3. Engine oil filler cap 4. Engine oil dipstick 5. Brake fluid reservoir 6. Power distribution box 7. Battery 8.
5.0L V8 engine 1. Engine coolant reservoir 2. W indshield washer fluid reservoir 3. Engine oil filler cap 4. Automatic transmission fluid dipstick 5. Brake fluid reservoir 6. Power distribution box 7. Battery 8. Power steering fluid reservoir 9. Engine oil dipstick 10.
3. Set the parking brake and ensure the gearshift is securely latched in P (Park). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick).
6. W ipe the indicator clean. Insert the indicator fully , then remove it again. • If the oil level is between the MIN and MAX marks, or between teh MIN and FULL marks the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range or the MIN-FULL range.
Engine Oil Recommendations 5.0L Engine Look for this certification trademark. SAE 5W -20 engine oil is recommended. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). Use Motorcraft (Part: XO–5W20–QSP in U.
SAE 5W -30 engine oil is recommended. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). Use Motorcraft (Part: XO–5W30–QSP in U.S.) or an equivalent oil meeting Ford Specification WSS-M2C153–G. Do not use supplemental engine oil additives, oil treatments or engine treatments.
2. Visually inspect the fluid level. 3. If necessary , add brake fluid from a clean un-opened container until the level reaches MAX. Do not fill above this line. 4. Use only a DOT 3 brake fluid certified to meet Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter .
Only use a washer fluid that meets Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter . State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive.
When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “cold fill level” or within the “cold fill range” as listed on the engine coolant reservoir (depending upon application).
Adding engine coolant Use only Ford Premium Engine Coolant E2FZ-19549-AA (in Canada, Motorcraft CXC-10) or a premium engine coolant that meets Ford specification ESE-M97B44-A. Use only Ford G05 Engine Coolant WSS—M97B51–A1 (in Canada, Motorcraft CXC-10) or a premium engine coolant that meets Ford specification ESE-M97B44-A.
Plain water may be added in an emergency , but you must replace it with a 50/50 mixture of engine coolant and distilled water as soon as possible. Check the coolant level in the reservoir before you drive your vehicle the next few times (with the engine cool).
Coolant refill capacity T o find out how much fluid your vehicle’ s cooling system can hold, refer to Refill capacities in the Capacities and specifications chapter . Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter .
CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenance guide for the service interval schedules. If adding fluid is necessary , use only MERCON t AT F . • 4.0L SOHC V6 engine • 5.0L V8 engine 1.
6. If the fluid is low , add fluid in small amounts, continuously checking the level until it reaches the correct operating range. Be sure to put the cap back on the reservoir . T RANSMISSION FLUID Checking automatic transmission fluid (if equipped) Refer to your scheduled maintenance guide for scheduled intervals for fluid checks and changes.
Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the ambient temperature is above 10°C (50°F). Correct fluid level The transmission fluid should be checked at normal operating temperature 66°C-77°C (150°F-170°F) on a level surface.
High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition.
CHECKING AND ADDING TRANSFER CASE FLUID (IF EQUIPPED) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications.
BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However , for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the scheduled maintenance guide for the service interval schedules.
Batteries normally produce explosive gases which can cause personal injury . Therefore, do not allow flames, sparks or lighted substances to come near the battery . When working near the battery , always shield your face and protect your eyes. Always provide proper ventilation.
• The vehicle may need to be driven 16 km (10 miles) or more to relearn the idle and fuel trim strategy . • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.
Changing the wiper blades T o replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. T urn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm.
T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles). • Adjust tire pressure to recommended specifications found on the Certification Label or the T ire Label.
Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity .
SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all weather treads to provide traction in rain and snow . However , in some climates, you may need to use snow tires and chains.
If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury . Automotive fuels can cause serious injury or death if misused or mishandled.
• Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors, or skin contact could cause an adverse reaction. In sensitive individuals, serious personal injury or sickness may result.
Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. W e do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas.
Running out of fuel A void running out of fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: • Y ou may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine.
If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury . Fuel Filter For fuel filter replacement, see your dealer or a qualified service technician.
For consistent results when filling the fuel tank: • T urn the engine/ignition switch to the off position prior to refueling, an error in the reading will result if the engine is left running. • Use the same filling rate setting (low — medium — high) each time the tank is filled.
Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy . Habits • Smooth, moderate operation can yield up to 10% savings in fuel.
Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. • Carrying unnecessary weight may reduce fuel economy (approximately 0.
• Do not turn off the ignition while your vehicle is moving, especially at high speeds. • Have the items listed in your scheduled maintenance guide performed according to the specified schedule.
Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostics system. If your “Check Engine/Service Engine Soon” light is on, refer to the description in the W arning Lights and Chimes section of the Instrumentation chapter .
Replacing headlamp bulbs T o remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position, then lift hood and open the hinged headlamp cover .
If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used. 1. W ith the flat side of the new bulb’ s plastic base facing upward, insert the glass end of the bulb into the lamp assembly . Y ou may need to turn the bulb left or right to align the grooves in the plastic base with the tabs in the lamp assembly .
4. Rotate bulb socket counterclockwise about 1 ⁄ 4 turn and remove from lamp assembly . 5. Carefully pull bulb straight out of socket and push in the new bulb. 6. Install bulb socket in lamp assembly by turning clockwise. 7. Align the parking lamp assembly and push to snap in place.
Replacing license plate lamp bulbs 1. Remove two screws and the license plate lamp assembly from the liftgate. 2. Remove bulb socket from lamp assembly by turning counterclockwise. 3. Pull the bulb out from socket and push in the new bulb. 4. Install the bulb socket in lamp assembly turning it clockwise, 5.
4. Pull the bulb straight out of the socket and push in the new bulb. T o complete installation, follow the removal procedure in reverse order . USING THE RIGHT BULBS Replacement bulbs are specified in the chart below . Headlamp bulbs must be marked with an authorized “D.
AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician.
W axing your vehicle W axing your vehicle on a regular basis will reduce minor scratches and paint damage. W ax when water stops beading on the surface. This could be every three or four months, depending on operating conditions. Use only carnauba or synthetic-based waxes.
• Cover the highlighted areas to prevent water damage when cleaning the engine. • 5.0L • 4.0L SOHC • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning the wheels W ash with the same detergent as the body of your vehicle.
The brushes used in some automatic car washes may damage the finish on your wheels. Before going to a car wash, find out if the brushes are abrasive. Underbody Flush the complete underside of vehicle frequently . Keep body drain holes unplugged. Inspect for road damage.
Do not use chemical solvents or strong detergents when cleaning the seat mounted side air bag. Such products could contaminate the side air bag system and affect performance of the side air bag in a collision. Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth.
Cleaning leather seats (if equipped) T o clean, simply use a soft cloth dampened with water and a mild soap. W ipe the leather again with a damp cloth to remove soap residue. Dry with a soft cloth. For tougher soiling concerns, Ford recommends using the Deluxe Leather Care Kit F8AZ-19G253–AA, which is available from your Ford Dealer .
MOTORCRAFT PART NUMBERS Component 4.0L SOHC V6 engine 5.0L V8 engine Air filter element F A-1658 F A-1658 Fuel filter FG-986B FG-986B Battery BXT -65-650 BXT -65-650 Oil filter FL-1A FL-820S PCV valve EV -225 EV -152 Spark plugs* AGSF-22PP A WSF-32EE** * Refer to V ehicle Emissions Control Information (VECI) decal for spark plug gap information.
REFILL CAPACITIES Fluid Ford Part Name Application Capacity Brake fluid High Performance DOT 3 Motor V ehicle Brake Fluid All Fill to the MAX line on reservoir Engine oil (including filter change) Motorcraft SAE 5W -30 Super Premium Motor Oil 4.0L 4.7L (5.
Fluid Ford Part Name Application Capacity Front axle lubricant Motorcraft SAE 80W -90 Premium Rear Axle Lubricant 4x4 vehicles 1.7L (1.8 quarts) Rear axle lubricant 4 Motorcraft SAE 80W -90 Premium Rear Axle Lubricant Refer to Footnote 5 2.9-3.1L (5.5-5.
lubricants are not to be checked or changed unless a leak is suspected or service is required. The axle lubricant should be changed any time the axle has been submerged in water . Add 118 ml (4 oz.) of Additive Friction Modifier C8AZ-19B546-A or equivalent meeting Ford specification EST -M2C118–A for complete refill of T raction-Lok axles.
Item Ford part name or equivalent Ford part number Ford specification Automatic transmission 2 Motorcraft MERCON t VA T F XT -5-QM MERCON t V Power steering fluid Motorcraft MERCON t AT F XT -2-QDX ME.
4.0L vehicles with limited slip differentials and all 5.0L applications use rear axles that are filled with Motorcraft SAE 75W -140 High Performance Synthetic Rear Axle Lubricant, part number F1TZ-19780-B, Ford specification WSL-M2C192-A. 4.0L vehicles with limited slip differentials and all 5.
VEHICLE DIMENSIONS V ehicle dimensions mm (in) (1) Overall length 4 845 (190.7) (2) Overall width 1 832 (72.1) (3) Maximum height* 1 817 (71.5) (4) Wheelbase 2 889 (113.
4 1 3 5 2 Capacities and specifications 253.
IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’ s side.
Ford Extended Service Plan Y ou can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.
If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing dealership. 2. If your inquiry or concern remains unresolved, contact the Sales Manager or Service Manager at the dealership.
If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss W arranty Act or state replacement or repurchase laws.
Concerns are ineligible for review if the New V ehicle Limited W arranty has expired at receipt of your application and, in certain states eligibility is dependent upon the customer’ s possession of the vehicle. Eligibility may differ according to state law .
• a brief summary of the action taken by the dealer(s) and Ford Motor Company • the names (if known) of all the people you contacted at the dealership(s) • a description of the action you expect to resolve your concern Y ou will receive a letter of explanation if your application does not qualify for Board review .
Y ou may also contact the North American Customer Relationship Center at 1-800-392-3673 (Ford), TDD for the hearing impaired: 1-800-232-5952 or by writing to the Center at the following address: Ford Motor Company Customer Relationship Center 16800 Executive Plaza Drive P .
The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel.
Ford Deluxe Leather and Vinyl Cleaner (not available in Canada) Motorcraft Vinyl Cleaner (Canada only) Ford Extra Strength T ar and Road Oil Remover* (not available in Canada) Ford Extra Strength Upho.
Comfort and convenience Cargo net Cargo organizer Cargo shade Cargo tray Engine block heaters Home link visor T ire step T ravel equipment Auto headlamps with daytime running lamps (DRL) Cellular phon.
Protection and appearance equipment Air bag anti-theft locks Cargo liners, interior Carpet floor mats Cleaners, waxes and polishes Door edge guards Front end covers (full and sport) Hood deflectors In.
• Mobile communications systems may harm the operation of your vehicle, particularly if they are not properly designed for automotive use or are not properly installed. When operated, such systems may cause the engine to stumble or stall or cause the transmission to be damaged or operate improperly .
REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company .
A Air bag supplemental restraint system ........................ 127–128, 132 and child safety seats ............ 129 description ......................128, 132 disposal .................................... 135 driver air bag ..................130, 133 indicator light .
Certification Label ....................254 Child safety restraints ..............135 child safety belts .................... 135 Child safety seats ......................136 attaching with tether straps .. 140 in front seat ..........................
Driveline universal joint and slip yoke ....................................216 Driving under special conditions .......................... 163, 166 mud .......................... 162–163, 165 sand ................................. 163, 165 snow and ice .
engine coolant temperature gauge ......................................... 14 engine oil pressure gauge ........ 16 fuel gauge .................................. 16 odometer ................................... 15 speedometer ..........................
L Lamps bulb replacement specifications chart ................ 239 cargo lamps ............................... 22 daytime running light ...............21 fog lamps ................................... 21 headlamps ................................. 21 headlamps, flash to pass .
fluid, checking and adding .... 212 fluid, refill capacity ................247 fluid, specifications .........249, 251 Preparing to drive your vehicle ........................................ 152 R Radio ............................................ 36 Relays .
T raction-lok rear axle ............... 167 T ransfer case fluid checking ......................... 216 T ransmission ............................. 153 fluid, checking and adding (automatic) ............................. 213 fluid, refill capacities .
275.
276.
277.
278.
Item Information Required fuel Unleaded fuel only - 87 octane Fuel tank capacity 75.5L (21.0 gallons) 4.0L Engine oil capacity (includes filter change) 4.7L (5.0 quarts). Use Motorcraft SAE 5W -30 Super Premium Motor Oil, Ford specification WSS-M2C153-G.
handle. MERCON t and MERCON t V are not interchangeable. DO NOT mix MERCON t and MERCON t V . Refer to your scheduled maintenance guide to determine the correct service interval. 3 Indicates only approximate dry-fill capacity . Some applications may vary based on cooler size and if equipped with in-tank cooler .
Ein wichtiger Punkt beim Kauf des Geräts Mercury 2001 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Mercury 2001 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Mercury 2001 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Mercury 2001 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Mercury 2001 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Mercury 2001 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Mercury 2001 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Mercury 2001. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Mercury 2001 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
