Benutzeranleitung / Produktwartung Tribute (2002) des Produzenten Mazda
Zur Seite of 277
Introduction 4 Congratulations 4 Safety and environment protection 5 Symbol glossary 8 Instrument Cluster 14 W arning and control lights 14 Gauges 20 Entertainment Systems 23 AM/FM stereo with CD 23 A.
Seating and Safety Restraints 109 Seating 109 Safety restraints 120 Air bags 131 Child restraints 140 Driving 150 Starting 150 Brakes 155 T ransmission operation 159 V ehicle loading 178 T railer towi.
Maintenance and Specifications 225 Hood 231 Engine compartment 233 Engine oil 235 Battery 239 Fuel information 246 Air filter(s) 261 Refill capacities 267 Engine data 269 V ehicle dimensions 269 Accessories 272 Cellular phone warning 272 Index 273 All rights reserved.
The following warning may be required by California law: CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
W ARNING: This Owner’ s Guide describes every option and model variant available and therefore some of the items covered may not apply to your particular vehicle. Furthermore, due to printing cycles it may describe options before they are generally available.
W arning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind. Protecting the environment W e must all play our part in protecting the environment.
SPECIAL NOTICES Special instructions For your added safety , your vehicle is fitted with sophisticated electronic controls. W ARNING: By operating other electronic equipment (e.g. mobile telephone without exterior aerial) electromagnetic fields can occur which can cause malfunctions of the vehicle electronics.
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Protecting the Environment Fasten Safety Belt Air Bag-Front Air Bag-Side Child Sea.
V ehicle Symbol Glossary Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm System Feature Engine Oil Engine Coolant Engine Coolant T emperatur.
INFORMATION ABOUT THIS GUIDE The information found in this guide was accurate at the time of printing. Mazda may change the contents without notice. Introduction 10.
Instrument Cluster 11.
Instrument cluster (pg. 14) W indshield wiper/washer control (pg. 82) Manual tilt steering wheel lever (pg. 85) Driver air bag (pg. 131) Speed controls* (pg. 90) Instrument panel dimmer control (pg. 74) Power mirror control* (pg. 89) Fog lamp control* (pg.
Audio system (pg. 23) 4WD control* (pg. 169) Climate controls (pg. 69) Auxiliary power point (pg. 87) Rear window defroster control (pg. 72) Hazard flasher control (pg.
W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
T emporary malfunctions may cause your light to illuminate. Examples are: 1. The vehicle has run out of fuel. (The engine may misfire or run poorly .) 2. Poor fuel quality or water in the fuel. 3. The fuel cap may not have been properly installed and securely tightened.
Air bag readiness Illuminates to confirm that the air bags (front or side) are operational. If the light fails to illuminate, continues to flash or remains on, have the system serviced immediately . Safety belt Illuminates to remind you to fasten your safety belts.
W ARNING: If the light remains on, continues to flash or fails to illuminate, have the system serviced immediately . With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with the parking brake released.
Engine oil pressure Illuminates when the oil pressure falls below the normal range. Check the oil level and add oil if needed. Refer to Engine oil in the Maintenance and specifications chapter . T o avoid engine damage, stop the vehicle as soon as safely possible and switch off the engine immediately .
Low coolant (if equipped) Illuminates when the coolant level in the coolant reservoir is low and more needs to be added. For more information on adding engine coolant, refer to Engine coolant in the Maintenance and specifications chapter .
Key-in-ignition warning chime Sounds when the key is left in the ignition and the door , liftgate or liftgate window is opened. Headlamps ON warning chime Sounds when the headlamps or parking lamps are on, the key is removed from the ignition and the driver’ s door is opened.
NOTE: This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate. T achometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.
Fuel gauge Displays approximately how much fuel is in the fuel tank. The fuel gauge may vary slightly when the vehicle is in motion or on a grade. When refueling the vehicle from empty indication, the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel.
AM/FM RADIO WITH COMPACT DISC PLAYER V olume/power control Ensure that the ignition switch is in the ACC or ON position. Press the control to turn the audio system on. T urn the control to raise or lower the volume. Press the control again to turn the audio system off.
T une adjust The tune control works in radio mode. Tune adjust in radio mode • Press to move up the frequency band in individual increments. • Press to move down the frequency band in individual increments. Seek function The seek function control works in radio mode.
Scan function The scan function works in radio mode. Scan function in radio mode Press the SCAN control to hear a sampling of strong stations on the frequency band. Each station will play for approximately 5 seconds. Press the SCAN control again to remain on a station and disable this mode.
Bass adjust The bass adjust control allows you to increase or decrease the audio system’ s bass output. Press the AUDIO control until BASS is illuminated in the display . T urn the volume control to adjust to the desired level of bass. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
Radio station memory preset The radio is equipped with five station memory preset controls. These controls can be used to select up to five preset AM stations and ten FM stations (five in FM1 and five in FM2). Setting memory preset stations 1. Select the frequency band with the AM/FM control.
Random play in CD mode Press the RDM control during play . RDM will illuminate in the display . The next selection will be randomly selected. T o disengage random play , press the RDM control again. Repeat play The repeat play feature works in CD mode and repeats the current CD selection.
automatically reverse one hour . For example, if the original setting is 3:24, the time will change to 3:00. If the clock’ s current time setting is within the latter part of the hour (from 30 to 59 minutes), the hour setting will automatically advance one hour .
Press the control to turn the audio system on or off. T urn the control to raise or lower the volume. NOTE: T o prevent the battery from being discharged, do not leave the audio system on for a long period when the engine is not running. NOTE: Once the system is turned off, press the VOL control again to listen to the frequency last tuned to.
Note: If the FM broadcast signal becomes weak, reception automatically changes form STEREO to MONO for reduced noise and the ST incdicator will go out. T une audio control The TUNE control is a multi-functional control which works in radio, tape and CD modes to adjust the levels of bass, treble, balance, fade and mid-range.
T urn the TUNE control to the left for a lower frequency . T urn the TUNE control to the right for a higher frequency . Scan function The scan function works in radio and CD mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band.
Seek function in radio mode Press and momentarily hold the SEEK control. • Press to find the next listenable station up the frequency band. • Press to find the next listenable station down the frequency band. NOTE: If you continue to press and hold the control, the frequency will continue changing without stopping.
Bass adjust The bass adjust control allows you to increase or decrease the audio system’ s bass output. Press the audio control until BASS appears. T urn the control to increase (right) or decrease (left) the amount of bass output. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
T urn the control (right or left) to adjust between the front and rear speakers. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the audio control until BAL appears. T urn the control (right or left) to adjust between the right and left speakers.
Mid-range adjust (if equipped) Y our vehicle may be equipped with a mid-range adjust. The TUNE control allows you to adjust the mid-range levels. Press the audio control until MID appears in the display . T urn the control to the right to increase the mid-range.
The preset control number will illuminate in the display . This indicates the station is held in memory on the control you selected. Repeat this procedure to store other stations in memory . T o tune one in the memory , select AM, FM1 or FM2 and then press its channel preset button.
NOTE: If the power supply is interrupted, (fuse blows or the battery is disconnected), the preset channels will be canceled. T ape select T o begin tape play , insert a cassette tape into the cassette slot, with the open edge facing the right. Once inserted, the cassette tape will automatically begin play and T APE will appear in the display .
Rewind The rewind control works in CD mode. In CD mode, press and hold the rewind control to reverse through a track at a high speed. Repeat play The repeat play feature works in CD mode and allows you to listen to a selection repeatedly . Repeat play in CD mode Press the RPT control during play .
Press the DISC down control to skip back to the beginning of the previous CD. Ejecting a CD The eject feature works in CD mode. 1. Press the control to stop and eject a CD. The disc number and OUT will appear in the display . 2. Remove the CD. NOTE: When a CD is ejected during play , the next CD will be played automatically .
2. Press on the hour set control to adjust the hours. 3. Press on the minute set control to adjust the minutes. 4. Press the CLOCK control again to start the clock. NOTE: If the power supply to the unit is interrupted (if the fuse blows or the vehicle’ s battery is disconnected), the clock will need to be reset.
AM/FM RADIO WITH CASSETTE AND 6 DISC CD CHANGER V olume/power control Press the control to turn the audio system on or off. T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
AM/FM select The AM/FM select control works in radio, tape and CD modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in tape mode Press this control to stop tape play and begin radio play .
Scan function The scan function works in radio, tape or CD mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode. Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape.
Bass adjust The bass adjust control allows you to increase or decrease the audio system’ s bass output. Press the AUDIO once to access the system’ s bass adjust mode. T urn the control to increase (right) or decrease (left) the amount of bass output.
Setting memory preset stations 1. Select the frequency band with the AM/FM control. 2. Select a station. 3. Press and momentarily hold the desired preset control until a beep is heard. The preset control number will illuminate in the display . This indicates the station is held in memory on the control you selected.
CD select T o begin CD play (if CD[s] are loaded), press the CD control. The first track of the disc will begin playing. After that, CD play will begin where it stopped last.
Repeat play in CD mode Press the RPT control during play . RPT will illuminate in the display . The current selection will be repeated. T o disengage repeat play , press the RPT control again. Load The load feature allows you to load up to six single CDs into the audio system.
Eject function Press the control to stop and eject a tape. Random play/Blank skip feature Random play in CD mode The random play feature (RDM) works in CD mode and plays the selections on the current CD in random order . Press the RDM control during play .
AM/FM RADIO WITH CASSETTE T APE AND COMPACT DISC PLAYER/CHANGER (IN-DASH CD CHANGER) V olume/power control Ensure that the ignition is either in the ACC or ON position for the audio system to function. Press the control to turn the audio system on or off.
T urn the control to raise or lower the volume. NOTE: T o prevent the battery from being discharged, do not leave the audio system on for a long period when the engine is not running. NOTE: Once the system is turned off, press the VOL control again to listen to the frequency last tuned to.
Press the TUNE control to select the desired function. T urn the TUNE control to adjust the desired levels. Refer to T reble adjust for specific instructions on level adjustments. The TUNE control will also work in radio mode to manually increase or decrease the frequency .
Scan function The scan function works in radio and CD mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to disable scan mode. Scan function in CD mode Press the SCAN control during CD play to hear the first ten seconds of each track.
Press the audio control until TREB is displayed. T urn the control to increase (right) or decrease (left) the amount of treble output. Bass adjust The bass adjust control allows you to increase or decrease the audio system’ s bass output. Press the audio control until BASS appears.
T urn the control to increase (right) or decrease (left) the amount of bass output. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the audio control until F ADE appears. T urn the control (right or left) to adjust between the front and rear speakers.
Press the audio control until BAL appears. T urn the control (right or left) to adjust between the right and left speakers. Mid-range adjust (if equipped) Y our vehicle may be equipped with a mid-range adjust. The TUNE control allows you to adjust the mid-range levels.
T urn the control to the right to increase the mid-range. T urn the control to the left to decrease the mid-range. The level will display . Release the TUNE control when the desired level is reached. NOTE: Approximately 5 seconds after selecting any mode, the volume function will be automatically selected.
Auto memory tuning Auto memory tuning allows you to set strong radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Starting autoset memory preset 1.
The cassette’ s top side is playing when is illuminated in the display . The cassette’ s bottom side is playing when is illuminated in the display . NOTE: When a metal tape is inserted, the player will automatically compensate and MTL will appear in the display .
Repeat play in tape mode Press the RPT control during play . RPT will illuminate in the display . The current selection will be repeated. T o disengage repeat play , press the RPT control again. NOTE: RPT may not operate properly if: • A tape was recorded at a low level.
Disc search Disc search works in CD mode. Press the DISC up control to skip forward to the beginning of the next CD. Press the DISC down control to skip back to the beginning of the previous CD. Dolby T noise reduction Dolby t noise reduction operates only in tape mode.
T o disengage APC, press the APC control again. If APC detects 15 seconds of blank space, it will automatically advance the tape to the next selection. NOTE: APC may not operate properly if: • A tape was recorded at a low level. • A tape has long, silent intervals.
Inserting CDs into desired tray number 1. Press and hold the LOAD control until a beep is heard. 2. Press the memory preset control for the deisred CD tray within 5 seconds after the beep is heard. 3. When IN is displayed, insert the CD. NOTE: The CD cannot be inserted to the desired tray number if the number is already occupied.
Multiple ejection 1. Press and hold the CD eject control for approximately 2 seconds until a beep is heard. 2. W ait approximately 5 seconds or press the CD eject control again within 5 seconds after the beep is heard. 3. Remove the CD. The next CD will then be ejected.
2. Press on the hour set control to adjust the hours. 3. Press on the minute set control to adjust the minutes. 4. Press the CLOCK control again to start the clock. NOTE: If the power supply to the unit is interrupted (if the fuse blows or the vehicle’ s battery is disconnected), the clock will need to be reset.
T ROUBLESHOOTING THE CD CHANGER (IF EQUIPPED) If sound skips: • Y ou may be traveling on a rough road, playing badly scratched discs or the disc may be dirty . Skipping will not scratch the discs or damage the player . If your changer does not work, it may be that: • A disc is already loaded where you want to insert a disc.
• When driving over rough or uneven surfaces, the audio sound may jump. • The CD player has been designed to play CDs bearing the identification logo as shown. No other discs can be played. • Do not stick paper or tape on the CD. A void scratching the reverse side of the CD (the side without a label).
Radio reception factors Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.
MANUAL HEATING AND AIR CONDITIONING SYSTEM Fan speed control Controls the volume of air circulated in the vehicle. T emperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
NOTE: In snowy or dirty conditions, leave the mode selector in the OFF position. • MAX A/C- Uses recirculated air to cool the vehicle. MAX A/C is noisier than A/C but more economical and will cool the inside of the vehicle faster . Airflow will be from the instrument panel registers.
• (Defrost)-Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield. If the temperature is about 6°C (43°F) or higher , the air conditioner will automatically dehumidify the air to reduce fogging.
• Do not place objects over the defroster outlets. These objects can block airflow and reduce visibility through your windshield. A void placing small objects on top of the instrument panel. These objects may fall down into the defroster outlets and block airflow , in addition to, damaging the climate control system.
HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to turn on the headlamps.
Flash to pass Pull toward you slightly to activate and release to deactivate. FOG LAMP CONTROL (IF EQUIPPED) The fog lamps can only be turned on when the headlamp control is in the low beams position. Press the foglamp control to activate the fog lamps.
AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by your authorized Mazda dealer . TURN SIGNAL CONTROL • Push down to activate the left turn signal.
The dome lamp will stay on if the control is moved to the passenger side position. When the control is in the middle position, the lamp will only come on when a door is opened. If the control is moved to the driver’ s side position, the lamp will not come on at all.
BULBS Replacing exterior bulbs Check the operation of the following lamps frequently: • Headlamps • Fog lamps (if equipped) • High-mount brake lamp • Brake lamps • T urn signals • License plate lamp • T ail lamps • Back-up lamps Do not remove lamp bulbs unless they can be replaced immediately with new ones.
Function Number of bulbs T rade number Park/turn lamps (front) 2 3157 AK (amber) Headlamps 2 9003 Rear stop/tail lamps 2 3157K Rear turn lamps 2 3156K Rear license plate lamps 2 3156K/168 Backup lamp .
Handle a halogen headlamp bulb carefully and keep out of children’ s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hands could cause the bulb to break the next time the headlamps are operated. NOTE : If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used.
5. Pull the bulb straight out of the socket and push in the new bulb. 6. T o complete installation, follow the removal procedure in reverse order . Replacing front parking/turn lamp bulbs 1. Make sure that the headlamp control is in the OFF position. 2.
Replacing fog lamp bulbs (if equipped) 1. Remove the bulb socket from the fog lamp by turning counterclockwise. 2. Disconnect the electrical connector from the fog lamp bulb. 3. Connect the electrical connector to the new fog lamp bulb. 4. Install the bulb socket in the fog lamp turning clockwise.
WINDSHIELD WIPER AND W ASHER For intermittent operation, move control down one position. Adjust the rotary control to the desired speed setting. For normal or low speed wiper operation, move control down two positions from OFF . For high speed wiper operation, move control down three positions from OFF .
T o activate the windshield washer , pull control toward you. Release control to stop washer fluid spray . MIST FUNCTION Move control up and release for one wipe. Windshield wiper blades Check the wiper blades at least twice a year or when they seem less effective.
Changing the wiper blades T o replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. T urn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm.
T o activate the rear washer , rotate the control to the position and release. Rear window wiper blades Refer to Windshield wiper blades in this section for more information on rear wiper blades. MANUAL TILT STEERING COLUMN Push the tilt steering wheel lever downward to move the steering wheel up or down.
OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’ s overhead console will vary according to your option package. Storage compartment (if equipped) Press the OPEN control to open the storage compartment. The door will open slightly and can be moved to full open.
AUXILIARY POWER POINT W ARNING: Power outlets are designed for accessory plugs only . Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty . The auxiliary power point is located on the instrument panel below the radio.
POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. • Press the bottom portion of the rocker switch to open. One touch down • Press AUTO completely down to the second detent.
NOTE: This feature will only operate the driver’ s side window . Window lock The window lock feature allows only the driver to operate the power windows. T o lock out all the window controls except for the driver’ s press the right side of the control.
Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash. SPEED CONTROLS (IF EQUIPPED) T o turn speed control on • Press ON. NOTE: V ehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph).
T o turn speed control off • Press OFF . NOTE: Once speed control is turned off or the ignition is switched off, the previously programmed set speed will be erased. T o set a speed • Press SET ACC. NOTE: For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph).
T o set a higher set speed • Press and hold SET ACC. Release the control when the desired vehicle speed is reached or • Press and release SET ACC to operate the T ap-Up function. Each press will increase the set speed by 1.6 km/h (1 mph) or • Accelerate with your accelerator pedal.
T o disengage speed control • Depress the brake pedal or • Depress the clutch pedal (if equipped). NOTE: Disengaging the speed control will not erase the previously programmed set speed. NOTE: Fully depressing the clutch pedal may cause a flare in engine RPM as the throttle is returned to idle.
T o return to a previously set speed • Press RSM. NOTE: For RSM to operate, the vehicle speed must be faster than 48 km/h (30 mph). MOON ROOF (IF EQUIPPED) T o operate the moon roof: • The moon roof is equipped with an automatic, one-touch, express opening feature.
CENTER CONSOLE Y our vehicle may be equipped with a variety of console features. These include: • Utility compartment • Cupholders • Ashcup W ARNING: Use only soft cups in the cupholder .
W ARNING: The cover may cause injury in a sudden stop or accident if it is not securely installed. LIFTGATE T o open the rear window , pull the right side of the liftgate handle. T o open the liftgate, pull the left side of the liftgate handle. • Do not open the liftgate or liftgate glass in a garage or other enclosed area with a low ceiling.
LUGGAGE RACK The maximum load for the roof rack is 44 kg (100 lbs), evenly distributed on the crossbars. If it is not possible to evenly distribute the load, position it in the center or as far forward on the crossbars as possible. Always use the adjustable tie down loops to secure the load.
KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer . Y ou should always carry a second key with you in a safe place in case you require it in an emergency . Refer to SecuriLock y Passive Anti-Theft System for more information.
Childproof door locks When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door .
Unlocking the doors Press this control to unlock the driver’ s door . The interior lamps will illuminate. The flashers will flash twice to confirm the vehicle is unlocked. Press the control a second time within three seconds to unlock all doors. Locking the doors Press this control to lock all doors.
Replacing the battery The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. T ypical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle.
Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure.
The inside lights will not turn off if: • they have been turned on in the dome lamp control or • any door is open NOTE: The battery saver will shut off the interior lamps 40 minutes after the ignition has been turned to the OFF position.
Key information Y our vehicle is supplied with two coded keys. Only a coded key will start your vehicle. Spare coded keys can be purchased from your authorized Mazda dealership. Y our dealership can program your key or you can “do it yourself”, refer to Programming spare keys.
If your keys are lost or stolen you will need to do the following: • Use your spare key to start the vehicle. or • Have your vehicle towed to an authorized Mazda dealership. . The key codes will need to be erased from your vehicle and new key codes will need to be re-coded.
1. Insert the first previously programmed coded key into the ignition and turn the ignition from 2 (ACC) to 3 (ON) (maintain ignition in 3 (ON) for at least one second). 2. T urn ignition to 1 (LOCK) and remove the first coded key from the ignition. 3.
PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will respond if unauthorized entry is attempted. If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to authorized Mazda dealership, to aid in troubleshooting.
Disarming the system Y ou can disarm the system by any of the following actions: • Unlock the doors by using your remote entry transmitter . • Unlock the doors with a key . • Press the panic control on the remote entry transmitter . This will disarm the system only if the alarm is sounding.
SEA TING Adjustable head restraints (if equipped) Y our vehicle’ s seats are equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision.
W ARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. W ARNING: Sitting in a reclined position while the vehicle is moving is dangerous because you don’ t get the full protection from seat belts.
Using the manual lumbar support (if equipped) The lumbar support control is located on the inboard side of the driver’ s seat. T urn the lumbar support control clockwise to increase firmness. T urn the lumbar support control counterclockwise to increase softness.
Move the rear of the control up or down to raise or lower the rear portion of the seat cushion. Move the control in the directions shown to move the seat forward, backward, up or down. REAR SEATS Head restraints (if equipped) Y our vehicle’ s seats may be equipped with head restraints which are vertically adjustable.
Push control to lower head restraint. Folding down rear seats 1. Raise the rear seat head restraint and remove. 2. Place the head restraints under the front passenger seat for storage.
4. Flip seat forward. 5. Pull the seatback release strap toward the front seat. Make sure the seat belt buckle heads are fully extended towards the front of the vehicle and are away from the seatback. NOTE: When the seatback release strap is pulled use your other hand to guide the seatback.
6. Rotate seatback down into load floor position. W ARNING: Make sure seat belt buckle heads are not trapped underneath the seatback and that the seat belt buckle heads are fully extended towards the front of the vehicle. Seat belt buckle heads may break if they are trapped underneath the seatback as the seatback is rotated down.
2. Rotate seat cushion down into the seating position making sure that the seat cushion is locked into place and that the seat belt buckles are exposed. 3. Remove the head restraints stored under the front passenger seat and return them to the original position on the seat backs.
T o install the rear cushion 1. Push the cushion to the inboard side of the vehicle. 2. Make sure that the hinges are locked into place. Folding down rear seats 1. Raise the rear seat head restraint and remove. 2. Place the head restraints under the front passenger seat for storage.
3. Pull the seat release control on each side of the seat to release the locks. 4. Flip seat forward. 5. Pull the seatback release strap toward the front seat. Make sure the seat belt buckle heads are fully extended towards the front of the vehicle and are away from the seatback.
Returning the rear seats to upright position 1. Pull seatback up and into upright position making sure seatback locks into place. 2. Rotate seat cushion down into the seating position making sure that the seat cushion is locked into place and that the seat belt buckles are exposed.
SAFETY RESTRAINTS Safety restraints precautions W ARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. W ARNING: T o reduce the risk of injury , make sure children sit where they can be properly restrained.
W ARNING: Placing a child, 12 years or younger , in the front seat is dangerous. The child could be hit by a deploying air bag and be seriously injured or even killed. A sleeping child is more likely to lean against the door and be hit by the side air bag in a moderate collision.
Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. T o unfasten, push the release button and remove the tongue from the buckle.
When to use the automatic locking mode • Any time a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible.
How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.
Front safety belt height adjustment Y our vehicle has safety belt height adjustments for the driver and front passenger . Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o lower the shoulder belt height, push the button and slide the height adjuster down.
W ARNING: Failure to replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision. The seat belt pretensioners will only function once. After they are deployed, they will not work again and must be replaced immediately , even if there was no front seat occupant seated at the time.
W ARNING: The lap belts should fit snugly and as low as possible around the hips, not around the waist. Failure to position the lap belt correctly may cause serious injury in an accident. Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from).
Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding.
Reasons given... Consider ... 9 I was in a hurry 9 Prime time for an accident. Belt Minder reminds us to take a few seconds to buckle up. 9 Seat belts don’t work 9 Safety belts, when used properly , reduce risk of death to front seat occupants by 45% in cars, and by 60% in light trucks.
Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. NOTE: If unsure about the proper procedures, bring your vehicle to an authorized Mazda dealership for inspection. Inspect the safety belts to make sure there are no nicks, tears or cuts, replacing if necessary .
AIR BAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.
W ARNING: National Highway T raffic Safety Administration (NHTSA) recommends a minimum distance of at least 25 cm (10 inches) between an occupant’ s chest and the driver air bag module. W ARNING: Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries.
Children and air bags For additional important safety information, read all information on safety restraints in this guide. W ARNING: Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.
• diagnostic module • and the electrical wiring which connects the components. The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors.
Side air bag system (if equipped) W ARNING: Do not place objects or mount equipment on or near the air bag cover on the side of the seatbacks of the front seats or in front seat areas that may come into contact with a deploying air bag. This is dangerous.
W ARNING: Seating Position with Side Air Bags Sitting too close to the side air bag storage compartments or placing hands on them is extremely dangerous. A side air bag inflates with great force and speed directly out of the outboard shoulder of the front seat and expands along the front door on the side the car is hit.
W ARNING: All occupants of the vehicle including the driver should always wear their safety belts even when an air bag SRS is provided. How does the side air bag system work? The side air bag system c.
near -frontal or opposite side collisions, unless the collision causes sufficient lateral deceleration. W ARNING: Several air bag system components get hot after inflation. Do not touch them after inflation. W ARNING: If the side air bag has deployed, the air bag will not function again.
Disposal of air bags and air bag equipped vehicles For disposal of air bags or air bag equipped vehicles, see your authorized Mazda dealership. Air bags MUST BE disposed of by qualified personnel. W ARNING: Disposing of an air bag can be dangerous. Unless all safety procedures are followed, injury can result.
Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle. If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child’ s face or neck, the child should wear the lap and shoulder belt.
SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’ s instructions with the safety seat you put in your vehicle.
• Put the safety belt in the automatic locking mode. Refer to Automatic locking mode (passenger side front seat). Mazda recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Check to make sure the child seat is properly secured before each use. Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point.
3. Locate the correct anchor for the selected seating position. NOTE: There are three tether anchors located on the headliner at the rear of the vehicle. W ARNING: If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision.
Attaching safety seats with LA TCH (Lower Anchors and T ethers for Children) attachments for child seat anchors Some child safety seats have two rigid or webbing mounted attachments that connect to two anchors at certain seating positions in your vehicle.
The lower anchors for child seat installation are located at the rear section of the rear seat between the cushion and seat back. Follow the child seat manufacturer’ s instructions to properly install a child seat with LA TCH attachments. W ARNING: Attach LA TCH lower attachments of the child seat only to the anchors shown.
STARTING Positions of the ignition 1. LOCK, locks the gearshift lever and allows key removal. 2. ACCESSORY , allows the electrical accessories such as the radio to operate while the engine is not running. 3. ON, all electrical circuits operational. W arning lights illuminated.
W ARNING: Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine.
If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Push the clutch pedal to the floor . 3. T urn the key to 3 (ON) without turning the key to 4 (ST ART). Note: If there is difficulty in turning the key , firmly rotate the steering wheel left and right until the key turns freely .
Starting the engine Note: Whenever you start your vehicle, release the key as soon as the engine starts. Excessive cranking could damage the starter . 1. T urn the key to 4 (ST ART) without pressing the accelerator pedal and release as soon as the engine starts.
Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. T ake precautions to avoid its dangerous effects. W ARNING: If you ever smell exhaust fumes of any kind inside your vehicle, have your authorized Mazda dealer inspect and fix your vehicle immediately .
BRAKES Y our service brakes are self-adjusting. Refer to the service maintenance section for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’ s brake system.
W ARNING: The Anti-Lock system does not decrease the time necessary to apply the brakes or always reduce stopping distance. Always leave enough room between your vehicle and the vehicle in front of you to stop.
Parking brake Apply the parking brake whenever the vehicle is parked. T o set the parking brake, apply the brake pedal and pull the parking brake handle up as far as possible. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released.
STEERING Y our vehicle is equipped with power steering. Power steering uses energy from the engine to help steer the vehicle. T o prevent damage to the power steering pump: • Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running.
W ARNING: V ehicles with a higher center of gravity such as utility and four -wheel drive vehicles handle differently than vehicles with a lower center of gravity . Utility and four -wheel drive vehicles are not designed for cornering at speeds as high as passenger cars.
2. Locate the access cover plate to the brake-shift interlock override. It is located on the top of the steering column. 3. Insert a tool (or a screwdriver) into the right-hand side of the brake-shift interlock access cover and remove the cover .
4. Insert a tool (or screw driver) into the access hole to override the brake-shift interlock. Apply the brake and shift into Neutral while holding down the override tab. If it is necessary to use the above procedure to move the gearshift lever , it is possible that a fuse has blown or the vehicle’ s brakelamps are not operating properly .
Driving with an automatic overdrive transaxle Y our automatic transaxle electronically controls the shift feel by using an adaptive learning strategy .
R (Reverse) W ith the gearshift lever in R (Reverse), the vehicle will move backward. Y ou should always come to a complete stop before shifting into and out of R (Reverse). W ARNING: Make sure the rearward path of the vehicle is unobstructed before moving the vehicle in reverse.
If the O/D OFF indicator light is flashing on and off repeatedly when the vehicle is started or does not come on when the O/D OFF control is pressed, there may be a transaxle electronic system malfunction. Y ou should contact your authorized Mazda dealer as soon as possible or damage to the transaxle could occur .
1 (First) Use 1 (First) for when added engine braking is desired when descending steep hills. The automatic transaxle will shift to the proper gear to ascend any grade without any need to shift to 1 (First). T o avoid damage to the engine and/or transaxle do not go faster than 56 km/h (35 mph) when in this gear .
2. Hold down the brake pedal. 3. Depress the clutch pedal. 4. W ithout depressing the accelerator pedal, turn the ignition to position 4 (ST ART), release the ignition as soon as the engine starts.
Reverse Make sure that your vehicle is at a complete stop before you shift into R (Reverse). Failure to do so may damage the transaxle. Put the gearshift lever into the neutral position and wait at least three seconds before shifting into R (Reverse).
2. Set the parking brake. 3. Shift into 1 (First). 4. T urn the ignition to position 1 (LOCK) to shut the engine off and remove the ignition key . W ARNING: Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully .
FOUR WHEEL DRIVE (4X4) SYSTEM (IF EQUIPPED) 4x4 system general information W ARNING: For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter . Y our vehicle is equipped with a 4x4 system.
increase tire wear and may damage driveline components. The 4x4 ON mode is intended for use only on consistently slippery or loose surfaces. • If your vehicle is equipped with this 4x4 system, a spare tire of a different diameter than the road tires should never be used.
The differences that make your vehicle so versatile also make it handle differently than an ordinary passenger car . Maintain steering wheel control at all times, especially in rough terrain. Since sudden changes in terrain can result in abrupt steering wheel motion, make sure you grip the steering wheel from the outside.
Do not rock the vehicle for more than a few minutes or damage to the transmission and tires may occur or the engine may overheat. Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transaxle may occur . W ARNING: Do not spin the wheels at over 56 km/h (35 mph).
Mud and water NOTE: • If you must drive through high water , drive slowly . T raction or brake capability may be limited. • When driving through water , determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly .
“T read Lightly” is an educational program designed to increase public awareness of land-use regulations and responsibilities in our nations wilderness areas. Mazda joins the U.S. Forest Service and the Bureau of Land Management in encouraging you to help preserve our national forest and other public and private lands by “treading lightly .
Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral, disengage overdrive or manually shift to a lower gear . When descending a steep hill, avoid sudden hard braking as you could lose control.
“pump” the brakes. Refer to the Brakes section of this chapter for additional information on the operation of the anti-lock brake system. • Never drive with chains on the front tires of 4x4 vehicles without also putting them on the rear tires. This could cause the rear to slide and swing around during braking.
Each day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires, and adjust if required. Check tire pressure with a tire gauge every few weeks (including spare). Safe operation requires tires that are neither underinflated nor overloaded.
and if the ignition system gets wet, your engine may stall. W ater may also enter your engine’ s air intake and severely damage your engine. If driving through deep or standing water is unavoidable, proceed very slowly . Never drive through water that is higher than the bottom of the hubs (for trucks) or the bottom of the wheel rims (for cars).
• Maximum T railer W eight Rating: Maximum weight of a trailer the vehicle is permitted to tow . The maximum trailer weight rating is determined by subtracting the vehicle curb weight for each engine/transmission combination, any required option weight for trailer towing and the weight of the driver from the GCWR for the towing vehicle.
W ARNING: Under no circumstance should these limitations be exceeded. Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury .
Follow these guidelines to ensure safe towing procedure: • Stay within your vehicle’ s load limits. • Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter . • Use extra caution when driving while trailer towing.
4x4 GCWR (Gross Combined W eight Rating)/T railer W eights Engine Maximum GCWR - kg (lbs.) T railer W eight Range - kg (lbs.) Maximum frontal area of trailer - m 2 (ft) 2 2.0L w/manual transmission 1,932 (4,260) 453 (1,000) 2.2 (24) 3.0L w/automatic transmission 2,477 (5,460) 907 (2,000) 2.
Hitches Do not use hitches that clamp onto the vehicle bumper . Use a load carrying hitch. Y ou must distribute the load in your trailer so that 10% of the total weight of the trailer is on the tongue. Safety chains Always connect the trailer’ s safety chains to the frame or hook retainers of the vehicle hitch.
• Use a lower gear when towing up or down steep hills. This will eliminate excessive downshifting and upshifting for optimum fuel economy and transmission cooling. • Anticipate stops and brake gradually . Exceeding the GCWR rating may cause internal transmission damage and void your warranty coverage.
Replace the rear axle lubricant any time the axle has been submerged in water . Rear axle lubricant quantities are not to be checked or changed unless a leak is suspected or repair required. Disconnect the wiring to the trailer before backing the trailer into the water .
CUSTOMER ASSISTANCE (EXCEPT PUERTO RICO) Y our complete and permanent satisfaction is our business. W e are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition.
CUSTOMER ASSISTANCE (PUERTO RICO) Y our complete and permanent satisfaction is our business. That is why all Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition.
HAZARD FLASHER CONTROL Use only in an emergency to warn traffic of vehicle breakdown, approaching danger , etc. The hazard flashers can be operated when the ignition is off. • The hazard lights control is located on the instrument panel by the radio.
1. T urn the ignition to the LOCK/OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. T urn the ignition to the ON position. Pause for a few seconds and return the key to the LOCK/OFF position.
Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.
The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 5A Canister V ent Control Solenoid 2 5A Blower Relay (coil), Rear Defrost Relay (coil.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 7 10A Passive Anti-theft T ransceiver (P A TS), Restraints Control Module 8 10A Cluster , Shift Lock Relay (coil), O/D .
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 24 15A Left/Right Stoplamps, High Mounted Stoplamp, Left/Right T railer Stoplamp, ABS Unit, ASC Unit (Brake Pedal Posit.
The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description Horn 15A Horn H/L LH 15A* Headlamp (High/Low Left, High Beams) H/L RH 15A* Headlamp .
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description DIODE — — H/L RELA Y MICRO — Headlamp (High/Low , Right/Left Relay) —— — INJ 30A** EEC (VPWR), EVR, MAF , IAC, Bulkhe.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description FUEL PUMP ISO — Fuel Pump Relay MAIN F AN ISO — Low Speed Fan Control Relay (2.0L Engine) High Speed Fan Control Relay 1 (3.0L Engine) ADD F AN ISO — High Speed Fan Control Relay 1 (2.
When driving with the temporary spare tire do not: • exceed 80 km/h (50 mph) under any circumstances • load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label •.
Tire change procedure W ARNING: When one of the front wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park) (automatic transaxle) or R (Reverse) (manual transaxle).
4. Lift the cargo cover and remove the tool bag with jack handle, lug nut wrench and long spare tire rod and spare tire from the wheel well. 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground.
• Rear jacking notches are located under the rear trailing arm. 6. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 25 mm (1 inch) off the ground. Never use the differentials as a jacking point.
8. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. 9. Lower the wheel by turning the jack handle counterclockwise.
NOTE: The cargo cover can not be reattached to the back seat clips when a full size tire is stowed. 13. Install cargo cover over the flat tire and secure with the plastic nut. 14. Unblock the wheels. JUMP STARTING YOUR VEHICLE W ARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes.
• Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure the vent caps are tight and level. • T urn the heater fan on in both vehicles to protect any electrical surges. T urn all other accessories off.
3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the disabled vehicle’ s engine, away from the battery and the fuel injection system.
2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they were connected.
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery .
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member , your roadside assistance center . It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt.
In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer , or flatbed transport vehicle) your vehicle (regardless of transmission powertrain configuration) can be flat towed (all wheels in the ground) under the following conditions: • Place the transmission in N (Neutral).
CUSTOMER ASSISTANCE (U.S.A.) Y our complete and permanent satisfaction is our business. W e are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition.
CUSTOMER ASSISTANCE (CANADA) Y our complete and permanent satisfaction is our business. W e are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition.
Please recognize that the resolution of service problems in most cases requires the use of your Mazda dealer’ s service facilities. personnel and equipment. W e urge you to follow the above three steps in sequence therefore for most effective results.
Provincial Administrators may be reached locally as listed below: Province/T erritory CAMV AP Number British Columbia & Y ukon T erritories (604) 681–0312 Alberta & Northwest T erritories (4.
CUSTOMER ASSISTANCE (PUERTO RICO) Y our complete and permanent satisfaction is our business. That is why all Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition.
MAZDA IMPORTERS/DISTRIBUTORS U.S.A (Importer/Distributor) Mazda North American Operations 7755 Irvine Center Drive Irvine, CA 92618–2922 P .O. Box 19734 Irvine, CA 92623–9734 TEL: 1 (800) 222–5500 (in U.S.A.) (949) 727–1990 (outside U.S.A.) (Distributor in each area) CANADA Mazda Canada Inc.
ADD-ON NON-GENUINE PARTS AND ACCESSORIES Non-genuine parts and accessories for Mazda vehicles can be found in stores. These may fit your vehicle, but they are not approved by the manufacturer for use with Mazda vehicles.
• Replacement Parts and Accessories Limited W arranty • T ire W arranty NOTE: Detailed warranty information is provided with your Mazda. OUTSIDE THE UNITED STATES AND CANADA Government regulations in the United States require that automobiles meet specific emission regulations and safety standards.
If you live in the U.S.A., all correspondence to Mazda Motor Corporation should be forwarded to: Mazda North American Operations 7755, Irvine Center Drive Irvine, California 92618–2922 P .O. Box 19734 Irvine, CA 92623–9734 Customer Assistance Center or toll free at 1 (800) 222–5500 If you live outside of the U.
IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’ s applicable e.
REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Mazda Corporation.
W ASHING YOUR VEHICLE W ash your vehicle regularly with cold or lukewarm water . Never use strong detergents or soap. If your vehicle is particularly dirty , use a quality car wash detergent. Always use a clean sponge, washing glove or similar device and plenty of water for best results.
REPAIRING PAINT CHIPS Minor scratches or paint damage from road debris may be repaired with Genuine Mazda T ouch-Up Paint. Observe the application instructions on the products. Remove particles such as bird droppings, tree sap, insect remains, tar spots, road salt and industrial fallout immediately .
• 3.0L DOHC V6 — Duratec Engine • Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. CLEANING NON-PAINTED PLASTIC EXTERIOR PARTS Use vinyl cleaner for routine cleaning.
CLEANING THE WIPER BLADES, WINDSHIELD AND REAR WINDOW If the wiper blades do not wipe properly , clean the wiper blade rubber element with undiluted windshield washer solution or a mild detergent. T o avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents.
CLEANING THE OVERHEAD CONSOLE Clean with a damp cloth, then wipe dry with a dry cloth. A void cleaner or polish that increases the gloss of the console.
INTRODUCTION Be extremely careful to prevent injury to yourself and others and damage to your vehicle when using this manual for inspection and maintenance. If you’re unsure about any procedure it describes, we strongly urge you to have a reliable and qualified service shop perform the work, preferably an Authorized Mazda Dealer .
SCHEDULE 1 I : Inspect and repair , clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air -blow method) R : Replace L : Lubricate Maintenance Item Maintenanc.
Maintenance Item Maintenance Interval (Number of months or km (miles), whichever comes first) Months 6 12 18 24 30 36 42 48 54 60 66 72 x 1000 Km 12 24 36 48 60 72 84 96 108 120 132 144 (x 1000 Miles) (7.5) (15) (22.5) (30) (37.5) (45) (52.5) (60) (67.
SCHEDULE 2 I : Inspect and repair , clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air -blow method) R : Replace L : Lubricate Maintenance Item Maintenanc.
Maintenance Item Maintenance Interval (Number of months or km (miles), whichever comes first) Months 4 8 12 16 20 24 28 32 36 40 44 48 x 1000 Km 8 16 24 32 40 48 56 64 72 80 88 96 (x 1000 Miles) (5) (.
*1 According to state and federal regulations, failure to perform maintenance on these items will not void your emissions warranties. However , Mazda recommends that all maintenance services be performed at the recommended time or mileage (kilometrage) period to ensure long-term reliability .
Working with the engine off • Automatic transmission: 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. T urn off the engine and remove the key . 3. Block the wheels to prevent the vehicle from moving unexpectedly .
2. At the front of the vehicle, lift up on the auxiliary latch handle located in the center between the hood and the grille. 3. Lift the hood open and secure it with the prop rod.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.0L DOHC I4 Zetec engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Brake fluid reservoir 4. Air filter assembly 5. Power distribution box 6. Battery 7. Engine oil filler cap 8. Engine oil dipstick 9.
3.0L DOHC V6 Duratec engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Automatic transmission fluid dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine oil dipstick 9. Engine oil filler cap 10.
WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low , add enough fluid to fill the reservoir . In very cold weather , do not fill the reservoir all the way .
3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmissions) or 1 (First) (manual transmissions). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick).
6. W ipe the indicator clean. Insert the indicator fully , then remove it again. • If the oil level is between the MIN-MAX or ADD-FULL marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN or ADD mark, add enough oil to raise the level within the MIN–MAX or ADD-FULL range.
4. Install the indicator and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise 1/4 of a turn until it is seated. T o avoid possible oil loss, DO NOT operate the vehicle with the engine oil level indicator and/or the engine oil filler cap removed.
BATTERY Y our vehicle is equipped with a Mazda maintenance-free battery which normally does not require additional water during its life of service. However , for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the service maintenance section for the service interval schedules.
W ARNING: When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners.
When the battery is disconnected or a new battery installed, the transmission must relearn its adaptive strategy . As a result of this, the transmission may shift firmly . This operation is considered normal and will not affect function or durability of the transmission.
• an accurate temperature readout from the engine coolant gauge. When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “cold fill level” or within the “cold fill range” as listed on the engine coolant reservoir (depending upon application).
W ARNING: Do not put engine coolant in the windshield washer fluid container . If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. The cooling system in your vehicle is filled with either green-colored or yellow-colored Mazda Premium Engine Coolant meeting Mazda Specifications.
reservoir when the engine is cool. Add the proper mixture of coolant and water to the “cold full” level. For all other vehicles, which have a coolant degas system with a pressurized cap, or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant.
If you have to add more than 1.0 liter (1.0 quart) of engine coolant per month, have your dealer check the engine cooling system. Y our cooling system may have a leak. Operating an engine with a low level of coolant can result in engine overheating and possible engine damage).
• Decreased engine coolant concentrations below 40% will decrease the corrosion protection characteristics of the engine coolant and may cause engine damage. • Decreased engine coolant concentrations below 40% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage.
Observe the following guidelines when handling automotive fuel: W ARNING: Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury . If fuel is swallowed, call a physician immediately , even if no symptoms are immediately apparent.
W ARNING: When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes.
Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. W e do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas.
Cleaner air Mazda endorses the use of reformulated “cleaner -burning” gasolines to improve air quality . Running out of fuel A void running out of fuel because this situation may have an adverse affect on powertrain components.
W ARNING: The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range. When refueling your vehicle after the fuel gauge indicates empty , you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank.
during summer and winter will show how temperature impacts fuel economy . In general, lower temperatures give lower fuel economy . Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy .
• Perform all regularly scheduled maintenance items. Follow the recommended maintenance schedule and owner maintenance checks found in your vehicle service maintenance section. Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed.
• A void running out of fuel. • Do not turn off the ignition while your vehicle is moving, especially at high speeds. • Have the items listed in your service maintenance section performed according to the specified schedule.
description in the W arning lights and chimes section of the Instrument Cluster chapter . Y our vehicle may not pass the I/M test with the indicator on. If the vehicle’ s powertrain system or its battery has just been serviced, the on-board diagnostics system is reset to a “not ready for I/M test” condition.
4. Check the fluid level in the reservoir . It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. 5. If the fluid is low , add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and MAX lines.
W ARNING: Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes. Seek medical attention if irritation persists.
5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary , refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. 6. Install the dipstick making sure it is fully seated in the filler tube.
If necessary , add fluid in 250 mL (1/2 pint) increments through the filler tube until the level is correct. If an overfill occurs, excess fluid should be removed by a qualified technician. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage.
W ARNING: Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes. Seek medical if irritation persists. If taken internally , drink water and induce vomiting.
Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be voided for any damage to the engine if the correct air filter element is not used. INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called T ire Quality Grades.
asphalt and concrete. A tire marked C may have poor traction performance. NOTE: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics.
Tire rotation Because your vehicle’ s tires perform different jobs, they often wear differently . T o make sure your tires wear evenly and last longer , rotate them as indicated in the service maintenance section. If you notice that the tires wear unevenly , have them checked.
Replacing the tires Replace the tires when the wear band is visible through the tire treads. W ARNING: When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label.
USING SNOW TIRES AND TRACTION DEVICES NOTE: Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all-weather treads to provide traction in rain and snow . However , in some climates, using snow tires and traction devices may be necessary .
REFILL CAPACITIES Fluid Classification Application Capacity Brake fluid High Performance DOT 3 Motor V ehicle Brake Fluid All Fill to line on reservoir Engine oil (including filter change) API service SJ, SAE 5W -20, 5W -30 Super Premium Motor Oil 2.0L I4 Zetec engine 4.
Fluid Classification Application Capacity Engine coolant 4 Mazda green-colored or yellow-colored Premium Engine Coolant 2.0L I4 Zetec engine with manual transaxle 5.0L (5.3 quarts) 3.0L V6 Duratec engine with automatic transaxle 10.0L (10.6 quarts) Rear axle lubricant SAE 80W -90 Premium Rear Axle Lubricant 4X4 1.
WHEEL AND TIRE SIZES V ehicle Grade Wheel T ire Spare Wheel Spare T ire DX/DX-V6 6.5JJx16 215/70R16 17x4T 135/90R17 LX-V6/ES-V6 7.0JJx16 235/70R16 17x4T 145/90R17 ENGINE SPECIFICA TIONS Engine 2.
3 2 1 5 4 Maintenance and Specifications 270.
IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’ s side.
CELL PHONES Use of cell phones and other devices by driver: W ARNING: Although not Mazda products, use of any electrical devices such as cell phones, computers, portable radios, vehicle navigation or other devices by the driver while the vehicle is moving is dangerous.
A ABS (see Brakes) ..................... 155 Air bag supplemental restraint system ................................ 131, 136 and child safety seats ............ 133 description ......................131, 136 disposal ............................ 135, 140 driver air bag .
in rear seat .............................. 143 Cleaning your vehicle engine compartment .............. 221 exterior ............................ 221, 224 exterior lamps .........................222 instrument panel ....................223 interior ..
refill capacities ........................ 267 specifications ..........................269 Exhaust fumes .......................... 154 F Fluid capacities ......................... 267 Foglamps ..................................... 74 Four -Wheel Drive vehicles description .
Hood .......................................... 231 I Ignition ............................... 150, 269 Infant seats (see Safety seats) .....................142 Inspection/maintenance (I/M) testing ........................................255 Instrument panel cleaning .
Mirrors cleaning ................................... 222 fold away ...................................90 side view mirrors (power) .......89 Moon roof .................................... 94 Motorcraft parts ........................251 O Octane rating .
Ein wichtiger Punkt beim Kauf des Geräts Mazda Tribute (2002) (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Mazda Tribute (2002) noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Mazda Tribute (2002) - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Mazda Tribute (2002) reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Mazda Tribute (2002) erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Mazda Tribute (2002) besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Mazda Tribute (2002) verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Mazda Tribute (2002). Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Mazda Tribute (2002) gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
