Benutzeranleitung / Produktwartung Prodigy des Produzenten MartinLogan
Zur Seite of 28
P RODIGY TM user ’s manual c l s e l e c t r o s t a t i c M ART I N L OGA N.
2 Contents C ONTENTS Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Installation in Brief . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation in Brief 3 I NST ALLA TION IN B RIEF W e know you are eager to hear your new Prodigy loud- speakers, so this section is provided to allow fast and easy set up. Once you have them operational, please take the time to read, in depth, the rest of the information in this manual.
4 Assembly NOTE: Assembly of the Prodigy requires 2 people. 1: Electrostatic P anel Assembly 1.1 Remove the top two screws and washers from the Prodigy woofer body . Back out the two screws and washers immediately beneath the two screws that were just removed until they protrude approximately 3 / 4 ” from the woofer body .
Assembly 5.
6 Introduction I NTRODUCTION Congratulations! Y ou have invested in one of the world’s premier loudspeak er systems. The MartinLogan Prodigy represents the culmination of an intensive, dedicated gro.
O PERA TION Operation 7 Because your MartinLogan Prodigys use an internal power supply to energize their electrostatic cells with high-voltage DC, they must be connected to an AC power source. F or this reason they are provided with the proper IEC standard power cords.
P RODIGY TM Please take note of the jumper clips installed under the binding posts. These clips attach the high and low frequency sections of the crossover together . Leaving these in place, connect the (+) wire from your amplifier to either red binding post and the (-) wire from your amplifier to either black binding post (See F igure 1).
With horizontal bi-amping , one amplifier drives the high pass (ESL) section while the second amplifier drives the low pass (WOOFER) section. T o horizontally bi-amp your Prodigys you must loosen the binding posts and remove the jumper clips. Connect the low frequency amplifier to the lower set of binding posts of both speakers.
10 Placement P LACEMENT By now your speakers should be placed approximately two to three feet from the front wall, the wall in front of the listening position, and at least one to two feet from the side walls. Y our sitting distance should be further than the distance between the speakers themselves.
Placement 11 Imaging In their final location, your Prodigys should have a stage width somewhat wider than the speakers themselves. On well recorded music, the instruments should extend beyond the edges of each speaker to the left and to the right, yet a vocalist should appear directly in the middle.
12 Room Acoustics This is one of those areas that requires both a little back- ground to understand and some time and experimentation to attain the best performance from your system. Y our room is actually a component and an important part of your system.
on the floor or solid surface, it can shake as it produces sound and, consequently , the sound can be compro- mised. If your speaker is sitting on the carpet and only foot gliders are used, the bass can be ill defined and even boomy . The use of spikes is recommended to insure secured footing for your speakers.
Y our Prodigys launch a 30 degree dispersion pattern when viewed from above. This horizontal dispersion field gives a choice of good seats for the performance while minimizing interactions with side walls (See F igure 6). Make sure both speakers stand exactly at the same vertical angle, otherwise the image can be skewed or poorly defined.
Dispersion Interactions 15 Figure 8 – 9. As can be seen here, point source concepts invite a great deal of room interaction. While delivering good frequency response to a large listening audience, imaging is consequently confused and blurred. Figure 10– 11.
It had long been the practice of stereo buffs to connect their television to the stereo system. The advantage was the use of the larger speakers and more powerful amplifier of the stereo system. Even though the sound was greatly improved, i t was still mono and limited by the broadcast signal.
How can sound be reproduced by something that you are able to see through? Electrostatic energy makes this possible. Where the world of traditional loudspeaker technology deals with cones, domes, diap.
ESL P anel Critical Zone: 250Hz–20kHz The most significant advantage of MartinLogan ’s exclusive transducer technology reveals itself when you look at examples of other loudspeaker products on the market today . The Prodigy uses no crossover networks above 250 Hz because they are not needed.
Since the beginning of audio, achieving smooth dispersion has been a problem for all loudspeaker designers. Large panel transducers present even more of a challenge because the larger the panel, the more directional the dispersion pattern becomes.
20 Electrostatic Loudspeaker History In the late 1800s, any loudspeaker was considered exotic. T oday , most of us take the wonders of sound reproduction for granted. It was 1880 before Thomas Edison had invented the first phonograph. This was a horn-loaded diaphragm that was excited by a playback stylus.
Electrostatic Loudspeaker History 21 In 1947, Arthur Janszen, a young Naval engineer , took part in a research project for the Navy . The Navy was interested in developing a better instrument for testing microphone arrays.
22 Frequently Asked Questions F REQUENTL Y A SKED Q UESTIONS How do I clean my speak ers? Just use a dust free cloth or a soft brush to remove the dust from your speakers. W e recommend a specialty cloth (available through the XStatic shop at www .martinlogan.
Frequently Asked Questions 23 Will excessive smok e or dust cause any problems with my electrostatic speak ers? Exposure to excessive contaminants such as smoke or dust may potentially affect the performance of the electrostatic membrane, and may cause discoloration of the diaphragm membrane.
24 Troubleshooting T ROUBLESHOOTING No Output •Check that all your system components are turned on. •Check your speaker wires and connections. •Check all interconnecting cables. W eak Output, Loss of Highs • Check the power cord. Is it properly connected to the speaker? Exaggerated Highs, Brightness •Check the toe-in of the speakers.
The Prodigy hybrid speaker system consists of a broad-range single element electrostatic transducer integrated with a quick- response woofer . This approach takes advantage of the benefits that both technologies have to offer . Dispersion is a controlled 30 degrees.
AC. Abbreviation for alternating current. Active crossover . Uses active devices (transistors, ICs, tubes) and some form of power supply to operate. Amplitude. The extreme range of a signal. Usually measured from the average to the extreme. Arc. The visible sparks generated by an electrical discharge.
Inductance. The property of an electrical circuit by which a varying current in it produces a varying magnetic field that introduces voltages in the same circuit or in a nearby circuit. It i s measured in henrys. Inductor . A device designed primarily to introduce inductance into an electrical circuit.
2101 Delaware Street, Lawrence, Kansas 66046, USA tel 785.749.0133 fax 785.749.5320 www.martinlogan.com c l s e l e c t r o s t a t i c M ART I N L OGA N ©2000 MartinLogan, All rights reserved Rev.
Ein wichtiger Punkt beim Kauf des Geräts MartinLogan Prodigy (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie MartinLogan Prodigy noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für MartinLogan Prodigy - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von MartinLogan Prodigy reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über MartinLogan Prodigy erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon MartinLogan Prodigy besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von MartinLogan Prodigy verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit MartinLogan Prodigy. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei MartinLogan Prodigy gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
