Benutzeranleitung / Produktwartung BLS820 des Produzenten Makita
Zur Seite of 36
INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. Cor dless Compound Miter Sa w Equipped with Electric Bla.
2 SPECIFICATIONS Blade diameter ........................................................................................... 216 mm (8-1/2”) Hole (arbor) diameter ................................................................................. 15.88 mm (5/8”) Max.
3 For Y our Own Safety Read Instruction Manual Bef ore Operating T ool Save it f or future reference GENERAL SAFETY PRECA UTIONS USA005-1 (F or All T OOIS ) 1. KNO W Y OUR PO WER TOOL. Read the owner’ s manual carefully . Learn the tool’ s applications and limitations, as well as the specific potential hazards peculiar to it.
4 18. NEVER ST AND ON T OOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted. 19. CHECK D AMAGED P AR TS.
5 14. Make sure that the turn base is properl y secured so it will not move during opera- tion. Use the holes in the base to fasten the saw to a stable w ork platform or bench. NEVER use tool where operator positioning would be a wkward. 15. For your saf ety , remove the c hips, small pieces, etc.
6 IMPOR T ANT SAFETY INSTR UCTIONS FOR CHARGER & B A TTER Y CARTRIDGE USC002-3 1. SA VE THESE INSTRUCTIONS- This man- ual contains important safety and operat- ing instructions for battery charger .
7 ADDITIONAL SAFETY R ULES FOR CHARGER & B A TTER Y CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELO W 10°C (50°F) or ABO VE 40°C (104°F). 2. Do not attempt to use a step-up trans- former , an engine g enerator or DC power receptacle.
8 INST ALLA TION Installing auxiliary plate Installing the auxiliar y plate using the notch in the tool ’ s base and secure it by tightening the he x bolt. Bench mounting When the tool is shipped, the handle is lock ed in the lowered position by the stopper pin.
9 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and the batter y cartr idge is remov ed bef ore adjusting or checking function on the tool. Installing or removing battery cartridge • Alwa ys switch off the tool bef ore inser tion or remov al of the batter y cartr idge.
10 5. If you lea ve the battery car tridge in the charger after the charging cycle is complete, the charger will s witch into its “ trickle charge (maintenance charge) ” mode which will last appro ximately 24 hours. 6. After charging, unplug the charger from the power source.
11 • Check the sound of cooling f an, vent on the charger and batter y , which can be sometime clogged with dust. • The cooling system is in order although no sound of cooling fa n comes out, if the yellow w ar ning light will not flash. • Alwa ys keep clean the v ent on charger and batter y f or cooling.
12 Blade guard When lowering the handle, the b lade guard rises automati- cally . The guard is spring loaded so it retur ns to its original position when the cut is completed and the handle is raised. NEVER DEFEA T OR REMOVE THE BLADE GU ARD OR THE SPRING WHICH A TT A CHES T O THE GUARD .
13 P ositioning kerf board This tool is provided with the k erf boards in the tur n base to minimize tearing on the e xit side of a cut. The kerf boards are f actor y adjusted so that the saw b lade does not contact the kerf boards . Before use , adjust the kerf boards as fo llows: First, remov e the batter y car tridge.
14 Adjusting the miter angle Loosen the grip by turning counterclockwise. T ur n the turn base while pressing down the loc k lev er . When you hav e mov ed the grip to the position where the pointer points to the desired angle on the miter scale, securely tighten the grip clockwise .
15 • Do not pull the s witch tr igger hard without pressing in the lock-off b utton. This can cause switch breakage . T o prev ent the switch trigger from being accidentally pulled, a lock-off b utton is provided. T o star t the tool, press in the lock- off button and pull the s witch trigger .
16 Socket wrenc h storage The sock et wrench is stored as shown in the figure. When using the sock et wrench, pull it out of the wrench holder . After using the sock et wrench, retur n it to the wrench holder .
17 Press the shaft lock to loc k the spindle and use the socket wrench to loosen the he x bolt clockwise. Then remo ve the he x bolt, outer flange and blade. T o install the blade, mount it carefully onto the spindle , mak- ing sure that the direction of the arrow on the surf ace of the blade matches the direction of the arro w on the blade case.
18 Dust bag The use of the dust bag makes cutting operations clean and dust collection easy . T o attach the dust bag, fit it onto the dust nozzle. When the dust bag is about half full, remov e the dust bag from the tool and pull the f astener out.
19 V ertical vise The vertical vise can be installed in two positions on either the left or right side of the guide fence or the holder assemb ly (optional accessor y). Insert the vise rod into the hole in the guide f ence or the holder assembly and tighten the screw to secure the vise rod.
20 CA UTION: • Grip the workpiece only when the projection is at the topmost position. F ailure to do so may result in insufficient securing of the workpiece. This could cause the workpiece to be thrown, cause damage to the b lade or cause the loss of control, which can result in PERSONAL INJUR Y .
21 • Gently press down the handle to perf or m the cut. If the handle is pressed down with f orce or if lateral fo rce is applied, the blade will vibr ate and leave a mark (saw mark) in the workpiece and the precision of the cut will be impaired. 1.
22 • When pressing the handle down, apply pressure parallel to the blade . If the pressure is not parallel to the blade during a cut, the angle of the blade might be shifted and the precision of the cut will be impaired.
23 There are crown and co ve molding joints which are made to fit “ Inside ” 90 ° corners ((1) and (2) in Fig. A) and “ Outside ” 90 ° corners ((3) and (4) in Fig. A). Measuring Measure the wall length and adjust workpiece on tab le to cut wall contact edge to desired length.
24 Example: In the case of cutting 52/38 ° type crown molding f or position (1) in Fig. A: • Tilt and secure be vel angle setting to 33.9 ° LEFT . • Adjust and secure miter angle setting to 31.
25 EN0002-1 Compound Miter Saw Miter and Bevel Angle Settings 000031 52 ˚ 38 ˚ Ceiling W all W all to Crown Molding Angle: 52/38 degrees W all Angle (deg.) Bevel Angle (deg.) Miter Angle (deg.) W all Angle (deg.) Bevel An gle (deg.) Miter Angle (deg.
26 EN0003-1 Compound Miter Saw Miter and Bevel Angle Settings 000032 45 ˚ 45 ˚ Ceiling W all W all to Crown Molding Angle: 45 degrees W all Angle (deg.) Bevel Angle (deg.) Miter Angle (deg.) W all Angle (deg.) Bevel An gle (deg.) Miter Angle (deg.) W all Angle (deg.
27 6. Cutting repetitive lengths When cutting se veral pieces of stoc k to the same length, ranging from 220 mm (8-5/8 ” ) to 365 mm (14-3/8 ” ), use of the set plate (optional accessor y) will f acilitate more efficient operation. Install the set plate on the holder (optional accessor y) as sho wn in the figure.
28 W ARNING: • Alwa ys be sure that the blade is sharp and clean for the best and saf est performance. Adjusting the cutting angle This tool is carefully adjusted and aligned at the fa ctor y , but rough handling ma y have aff ected the alignment. If your tool is not aligned properly , perform the follo wing: 1.
29 2. Bevel angle (1) 0 ° be vel angle Lower the handle fully and loc k it in the lowered position by pushing in the stopper pin. Loosen the le ver at the rear of the tool. Tu r n t h e 0 ° bev el angle adjusting bolt (lower bolt) on the right side of the ar m two or three re volutions counterclockwise to tilt the b lade to the ri ght.
30 Replacing carbon brushes Remov e and check the carbon brushes regularly . Replace when they we ar down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only iden- tical carbon brushes.
31 AC C E S S O R I E S CA UTION: • These accessories or attachments are recommended for use with your Makita tool specified in this man ual. The use of any other accessories or attachments might present a risk of injur y to persons. Only use accessory or attachment f or its stated pur pose.
Memo 32.
33 Fold Cut Stamp Timbre Makita Canada Inc. 1950 Forbes Street, Whitb y , Ontario L1N 7B7.
34 Y our answer s to the following questions are appreciated. Date Purchased Model No . Serial No. Initial Last Name Street Address City Province AGE: Male Female Married Single Month Day Y ear 20 Und.
35 F actory Ser vice Centres For the authorized service centre nearest you please refer to the local yellow pages directory under “ tools ” or con- tact our customer service department (Tel) 1-800-263-3734 When you need service.
Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
Ein wichtiger Punkt beim Kauf des Geräts Makita BLS820 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Makita BLS820 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Makita BLS820 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Makita BLS820 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Makita BLS820 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Makita BLS820 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Makita BLS820 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Makita BLS820. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Makita BLS820 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
