Benutzeranleitung / Produktwartung SR1522Z des Produzenten Mackie
Zur Seite of 19
1 SR1522z REPAIR MANUAL.
2 These instructions are intended to help restore any ailing SR1522z Active Loudspeaker back to factory working conditions. They show how to remove and replace the drivers and the ampli fi er assembly. Please contact Mackie Tech Support (1-800-898-3211) to receive a Service Request Number and Order Number for parts needed for this restoration.
3 Led PCB replacement: 3 Carefully begin to remove the grill. The grill has a tendency to want to “pop out,” so please be sure to hold the grill in place with your free hand while removing the screws with the other hand. Do not fully remove the grill as the cable is still fi rmly attached to the led PCB assembly.
4 Led PCB replacement continued: 6 Carefully remove the led PCB assembly from the back side of the grill. 7 The hard part is done, the rest is easy! Place the new led PCB assembly (part #0007334) where the old one was. Follow the same steps as above, but backwards 6 to 1.
5 Bottom woofer replacement: 1 Follow steps 1-4 of the led PCB replacement instructions, as the grill will need to be removed in order to access the bottom woofer. 2 Eight screws and fl at washers need to be removed from the woofer using the phillips head screwdriver.
6 Bottom woofer replacement continued: 6 The picture to the right shows what the SR1522z looks like with the grill and bottom woofer removed. Place the new woofer (part #0013913) where the old one was. Follow the same steps as above, but backwards 5 to 1, making sure to keep the led PCB assembly cable in front of the woofer.
7 Top woofer replacement: 1 Follow steps 1-4 of the led PCB replacement instructions, as the grill will need to be removed in order to access the top woofer. 2* Eight screws and fl at washers need to be removed from the woofer using the phillips head screwdriver.
8 Top woofer replacement continued: 5 The positive (solid blue) and negative (solid black) cables are still attached to the woofer terminals. Remove the cables from their terminals simply by pushing down on the terminal and pulling out the cable. Push down + - 6 This is what the SR1522z looks like with the grill and top woofer removed.
9 * The grill support (located just above screws 7 and 8 and outlined below) does not need to be taken off in order to remove and replace the top woofer.
10 High Frequency Driver replacement: 1 Follow steps 1-4 of the led PCB replacement instructions, as the grill will need to be removed in order to access the high frequency driver. 2 Four screws and fl at washers need to be removed from the horn using the 5mm allen wrench.
11 High Frequency Driver replacement continued: 6 This is what it looks like with the grill and horn removed. See the next page for further instructions and additional pictures on how to remove and replace the high frequency driver.
12 High Frequency Driver replacement continued: 8 Keep the four nuts, four locking washers, and four fl at washers in a safe place. 7 Four nuts and eight washers may be removed from the driver using the 8mm open end wrench. Turn counter- clockwise to loosen and remove, clockwise to tighten.
13 10 Four headless screws need to be removed from the high frequency driver. Pliers could help if the screws are too tight. Turn counter-clockwise to loosen and remove, clockwise to tighten. Keep the four headless screws in a safe place. Place the new high frequency driver (part #0008093) where the old one was.
14 3 The horn assembly is shown above with the high frequency driver circled. Four screws need to be removed from the driver using the 3mm allen wrench. 4 Keep the four screws in a safe place. 5 The diaphragm and plate adapter are easily removed from the horn assembly.
15 7 This is what the diaphragm (left) and plate adapter (right) both look like. Place the new diaphragm (part # coming soon) where the old one was. Follow the same steps as above, but backwards 6 to 1. Power up the SR1522z and the new diaphragm should now be pumping out those highs again.
16 Ampli fi er Assembly replacement: 1 Fourteen screws need to be removed from the ampli fi er assembly using the phillips head screwdriver. The ampli fi er assembly is capped by two cover plates outlined above.
17 Ampli fi er assembly replacement continued: 4 Once the two cover plates are removed, two more screws need to be taken out in order to separate the ampli fi er assembly from the cabinet. Keep the two screws in a safe place. 1 2 5 The ampli fi er assembly is now ready to be separated from the cabinet.
18 Ampli fi er assembly replacement continued: 6 Closeups of the led PCB cable and connector are shown above. The black wire of the cable is closest to the edge of the ampli fi er assembly. The cable only fi ts in one way. 7 See the pictures to the right for the closeups of the woofer and high frequency driver terminals.
19 8 Place the new ampli fi er assembly (part #0014138-00) where the old one was. Follow the same steps as above, but backwards 7 to 1. Remove the serial number from the faulty ampli fi er assembly (as shown in picture above) and place on the new ampli fi er assembly.
Ein wichtiger Punkt beim Kauf des Geräts Mackie SR1522Z (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Mackie SR1522Z noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Mackie SR1522Z - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Mackie SR1522Z reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Mackie SR1522Z erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Mackie SR1522Z besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Mackie SR1522Z verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Mackie SR1522Z. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Mackie SR1522Z gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
