Benutzeranleitung / Produktwartung DJ Mixer des Produzenten Mackie
Zur Seite of 32
OWNER’S MANUAL 2-Channel DJ Pr oduction Console with F ireW ire L R MAIN B A OL 0 2 4 7 10 20 30 OL 0 2 4 7 10 20 30 OL 0 2 4 7 10 20 30 PGM 2 REVER SE cont act- free cross-fader in fini u m PGM 1 L.
d. Pro DJ Pr oduction Console d.2 Pr o DJ Pr oduction C onsole 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with a dry cloth. 7.
Part No. SW0502 Rev . C 07/07 ©2007 LOUD T echnologies Inc. All Rights Reserved. (Loosely based on a dream sequence in which the d.2 Pro wins the big stock car competition, and takes his girl to the senior prom.) Owner’ s Manual Owner’ s Manual Contents SAFETY INSTRUCTIONS .
d. Pro DJ Pr oduction Console d.2 Pr o DJ Production C onsole Introduction Thank you for choosing a Mackie d.2 Pro DJ produc- tion console for scratch and club DJs. It contains all your favorite features in a scratch mixer , along with significant extras that you will come to appreciate.
5 Owner’ s Manual Owner’ s Manual Getting Started READ THIS P AGE!! Even if you never read manuals, please read and digest the safety instructions on page 2, and this page before you begin using the d.2 Pro mixer . Zero the Controls 1. T urn the rear panel power switch off.
d. Pro DJ Pr oduction Console d.2 Pr o DJ Production C onsole Hookup Diagrams Mobile DJ System: Rental, or W edding LINE MIC R R PGM 2 MAIN OUT MIC L L L L L R PHONO CD SEND R BOOTH FX GND LINE.
7 Owner’ s Manual Owner’ s Manual Radio Show Recor ding/Podcasting/having a good old time LINE MIC R R PGM 2 MAIN OUT MIC L L L L L R PHONO CD SEND R BOOTH FX GND LINE PHONO RETURN L(MONO) R R L R.
8 d. Pro DJ Pr oduction Console d.2 Pr o DJ Production C onsole T w o-T ur nta ble P or table System LINE MIC R R PGM 2 MAIN OUT MIC L L L L L R PHONO CD SEND R BOOTH FX GND LINE PHONO RETURN L(MON.
9 Owner’ s Manual Owner’ s Manual Club System LINE MIC R R PGM 2 MAIN OUT MIC L L L L L R PHONO CD SEND R BOOTH FX GND LINE PHONO RETURN L(MONO) R R L R LIVE RECORD ~ 100-240 VAC 50-60Hz 20W PGM 1.
10 d. Pro DJ Pr oduction Console d.2 Pr o DJ Production C onsole Rear Panel Features 1 . MI C I np u t This is a Neutrik “combo” input connector that ac- cepts either a balanced male XLR connector or a 1/4" balanced or unbalanced connector .
11 Owner’ s Manual Owner’ s Manual 9 . XL R M AI N O UT s These male XLR connectors provide a balanced mic- or line-level signal from the main level control [32].
1 d. Pro DJ Pr oduction Console d.2 Pr o DJ Production C onsole T op Panel Features MIC Input Section 1 . M I C LE V EL This knob adjusts the gain of the mic preamp for any micro- phone plugged into the mic input jack [1]. It ranges from +3 dB to +50 dB, with a fixed gain of +10 dB, giving an effective gain range of +13 dB to +60 dB.
1 Owner’ s Manual Owner’ s Manual Program Input Section 5. L E VE L This knob adjusts the gain of the program input signals selected by the position of the source select switch [26].
1 d. Pro DJ Pr oduction Console d.2 Pr o DJ Production C onsole Control Section . M A IN L E VE L This knob adjusts the main output level at the main out XLRs [9] (and to the RCA main outs [11] when the live/re- cord switch [12] is out).
15 Owner’ s Manual Owner’ s Manual Program Output Section 1. T R AN SF O RM The transform switch has three positions: latch- ing, center , and momen- tary . When the switch is latched, this program’s signal is on, and passes through to the outputs.
1 d. Pro DJ Pr oduction Console d.2 Pr o DJ Production C onsole . R E VE RS E L ED This LED lights when the reverse switch [49] has been activated for the crossfader . For more details, see the discussion of the reverse switches on the next page.
17 Owner’ s Manual Owner’ s Manual Front Panel Features 8. C O NT O U R Use the contour controls to adjust how fast or slow each fader responds to movement. In the slow position, the faders respond in a linear fashion, incr easing from minimum to maximum at the same rate.
18 d. Pro DJ Pr oduction Console d.2 Pr o DJ Production C onsole Appendix A: Ser vice Information W arranty Ser vice Details concerning W arranty Service are spelled out in the W arranty section on page 31. If you think your d.2 Pro has a problem, please do ev- erything you can to confirm it before calling for service.
19 Owner’ s Manual Owner’ s Manual Repair Service for Mackie products is available at a factory- authorized service center . Service for Mackie products living outside the United States can be obtained through local dealers or distributors. If your d.
0 d. Pro DJ Pr oduction Console d.2 Pr o DJ Production C onsole Appendix B: Connections XLR Connectors The d.2 Pro mic combo input accepts 3-pin male XLR connectors; the main outs accept 3-pin female XLR con- nectors. These are wir ed as follows, according to stan- dards specified by the AES (Audio Engineering Society).
1 Owner’ s Manual Owner’ s Manual Appendix C: T echnical Info continued Specifications Frequenc y Response (0 Hz to 0 kHz) : Mic input to any output: +0/–0.
d. Pro DJ Pr oduction Console d.2 Pr o DJ Production C onsole LOUD T echnologies Inc. is always striving to improve our prod- ucts by incorporating new and improved materials, components, and manufacturing methods. Therefore, we reserve the right to change these specifications at any time without notice.
Owner’ s Manual Owner’ s Manual Block Diagram PGM2 F ADER CURVE LOGIC CROSSF ADER CURVE LOGIC L R MAIN MAIN LEVEL P AN FW OUT 9 (MIC) L BOOTH OUTPUT L SUM R SUM LO MID HI R L MAIN MIX METER.
d. Pro DJ Pr oduction Console d.2 Pr o DJ Production C onsole Appendix D: T ransform Switch Rotation and Fader Replacement T ransform Switch Rotation From the factory , the transform switches operate vertically , that is (to get all technical for a moment) fore and aft.
5 Owner’ s Manual Owner’ s Manual Replacing Faders If the faders ever need to be replaced, this can be done with the help of your trusty screwdriver . 10. Follow steps 1 to 5 and remove the top panel. 11. T ake care to only remove the two outer scr ews of each fader you are r eplacing, as shown below.
d. Pro DJ Pr oduction Console d.2 Pr o DJ Production C onsole Appendix E: FireWire S y st e m R e q u i r e me n t s These are the minimum r equirements for your com- puter system to use the d.
7 Owner’ s Manual Owner’ s Manual From T o Computer output 1 Input to PGM 1 L Computer output 2 Input to PGM 1 R Computer output 3 Input to PGM 2 L Computer output 4 Input to PGM 2 R Computer output 5 Input to FX L Computer output 6 Input to FX R play through the same channel.
8 d. Pro DJ Pr oduction Console d.2 Pr o DJ Production C onsole Y ou can also select FireW ire as the FX r eturn input in- stead of the FX return TRS jacks [7]. Pr ess the FireWir e FX Return switch [37] in the FX section (see page 14). Beware of a possible feedback loop, if you ar e feeding the d.
9 Owner’ s Manual Owner’ s Manual 6. The next window reminds you to make sur e the d.2 Pro is NOT connected to your computer yet. Read the instructions and click “Continue.” 7. Y ou may get a warning about running the installer because it hasn’t passed Windows Logo testing.
0 d. Pro DJ Pr oduction Console d.2 Pr o DJ Production C onsole C o ns ol e ( P C on l y ) Y ou can use the console to change the sample rate and latency . The sample rate and latency value (also known as buffer size) may also be set in your DJ performance software application’ s “settings” window.
1 Owner’ s Manual Owner’ s Manual A. LOUD T echnologies Inc. warrants all materials, workmanship and proper operation of this product for a period of three years from the original date of purchase.
16220 W ood-Red Road NE • Woodinville, W A 98072 • USA United States and Canada: 800.898.3211 Europe, Asia, Central and S outh America: 425.487 .4333 Middle East and Africa: 31.20.654.4000 F ax: 425.487 .4337 • www .mackie.com E -mail: sales@mackie.
Ein wichtiger Punkt beim Kauf des Geräts Mackie DJ Mixer (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Mackie DJ Mixer noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Mackie DJ Mixer - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Mackie DJ Mixer reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Mackie DJ Mixer erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Mackie DJ Mixer besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Mackie DJ Mixer verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Mackie DJ Mixer. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Mackie DJ Mixer gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
