Benutzeranleitung / Produktwartung D-2 des Produzenten Mackie
Zur Seite of 28
OWNER’S MANUAL 2-Channel DJ Mixer with F ireWire Option LR MAIN B A OL 10 7 4 2 0 2 4 7 10 20 30 OL 10 7 4 2 0 2 4 7 10 20 30 OL 10 7 4 2 0 2 4 7 10 20 30 TRANSFORM PGM 2 TRANSFORM REVERSE contact-f.
2 d.2 DJ Mixer d.2 2-channel DJ Mix er 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings.
Part No. 0014096 Rev . A 7/05 ©2005 LOUD T echnologies Inc. All Rights Reserved. Printed in China. 3 Owner’ s Manual Owner’ s Manual Don’t forget to visit our website at www .mackie.com for more information about this and other Mackie products.
4 d.2 DJ Mixer d.2 2-channel DJ Mix er Introduction Thank you for choosing a Mackie d.2 Premium VCA Mixer for scratch and club DJs. It contains all your fa- vorite features in a scratch mixer , along with signifi cant extras that you will come to appreciate.
5 Owner’ s Manual Owner’ s Manual Getting Started READ THIS P AGE!! Even if you never reads manuals, please read and digest the safety instructions on page 2, and this page before you begin using the d.2 mixer . Zero the Controls 1. T urn the rear panel POWER switch off.
6 d.2 DJ Mixer d.2 2-channel DJ Mix er Hookup Diagrams (The following hookup diagrams show the d.2 with the optional FireW ire card installed.) Mobile DJ System: Rental, W edding, or Funeral LINE MIC .
7 Owner’ s Manual Owner’ s Manual Radio Show Recor ding/Podcasting/having a good old time LINE MIC RR PGM 2 MAIN OUT MIC LL L L LR PHONO CD SEND R BOOTH FX GND LINE PHONO RETURN LR R L R DESIGNED .
8 d.2 DJ Mixer d.2 2-channel DJ Mix er Tw o-T ur ntable Portable System LINE MIC RR PGM 2 MAIN OUT MIC LL L L LR PHONO CD SEND R BOOTH FX GND LINE PHONO RETURN LR R L R DESIGNED BY MACKOIDS IN WOODINV.
9 Owner’ s Manual Owner’ s Manual Club System LINE MIC RR PGM 2 MAIN OUT MIC LL L L LR PHONO CD SEND R BOOTH FX GND LINE PHONO RETURN LR R L R DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA • MANUFACTURED IN CHINA FABRIQUE EN CHINE • COPYRIGHT ©2005 • "MACKIE", AND THE RUNNING MAN FIGURE ARE TRADEMARKS OF LOUD TECHNOLOGIES, INC.
10 d.2 DJ Mixer d.2 2-channel DJ Mix er Rear Panel Features 1. MIC Input This is a Neutrik “combo” input connector that ac- cepts either a balanced male XLR connector or a 1/4" balanced or unbalanced connector . Use an XLR connec- tor for low-impedance microphones and a 1/4" connec- tor for high-impedance microphones.
11 Owner’ s Manual Owner’ s Manual If you only have one monitor speaker , just use one of the BOOTH Outputs and push in the BOOTH STEREO/ MONO switch [34] in the CONTROL section on the top panel. 9. XLR MAIN OUT s These male XLR connectors provide a balanced mic- or line-level signal from the MAIN LEVEL control [32].
12 d.2 DJ Mixer d.2 2-channel DJ Mix er T op Panel Features MIC Input Section 16. MIC LEVEL Contr ol This knob adjusts the gain of the mic preamp for any microphone plugged into the MIC input jack [1].
13 Owner’ s Manual Owner’ s Manual Program Input Section 25. LEVEL Contr ol This knob adjusts the gain of the PGM input signals selected by the position of the SOURCE Select switch [26].
14 d.2 DJ Mixer d.2 2-channel DJ Mix er Control Section 32 . MAIN LEVEL C ontrol This knob adjusts the main output level at the MAIN OUT XLRs [9] (and to the RCA Main Outs [11] when the LIVE/RECORD switch [12] is out). (Remem- ber , when the LIVE RE- CORD switch is pushed in, the RCA Main Outs are not affected by the MAIN LEVEL control.
15 Owner’ s Manual Owner’ s Manual Program Output Section 40. TRANSFORM Switch The transform switch has three positions: Latch- ing, Center , and Momen- tary . When the switch is Latched, this program’s signal is on, and passes through to the outputs.
16 d.2 DJ Mixer d.2 2-channel DJ Mix er 45. REVERSE LED This LED lights when the REVERSE switch [48] has been activated for the Crossfader . For more details, see the dis- cussion of the REVERSE switches [48] on the next page. 46. CR OSSF ADER The crossfader is used to fade between the two PGM signals in the MAIN outputs.
17 Owner’ s Manual Owner’ s Manual Front Panel Features 47 . CONT OUR Contr ols Use the CONTOUR controls to adjust how fast or slow each fader responds to movement. In the SLOW position, the faders respond in a linear fashion, incr eas- ing from minimum to maximum at the same rate.
18 d.2 DJ Mixer d.2 2-channel DJ Mix er Appendix A: Ser vice Information W arranty Ser vice Details concerning W arranty Service are spelled out in the W arranty section on page 27. If you think your d.2 has a problem, please do everything you can to confi rm it before calling for service.
19 Owner’ s Manual Owner’ s Manual Repair Service for Mackie products is available at a factory- authorized service center . Service for Mackie products living outside the United States can be obtained through local dealers or distributors. If your d.
20 d.2 DJ Mixer d.2 2-channel DJ Mix er Appendix B: Connections XLR Connectors The d.2 MIC combo input accepts 3-pin male XLR connectors; the MAIN OUT s accept 3-pin female XLR connectors. These are wir ed as follows, according to standards specifi ed by the AES (Audio Engineering Society).
21 Owner’ s Manual Owner’ s Manual Specifi cations Frequency Response : Mic Input to any Output: (T rim at 0 dB):+0, –1 dB 2 0 Hz to 20 kHz Line/CD Input to any Output: ±0.5 dB 2 0 Hz to 20 kHz Phono input to any Output: ±1 dB of RIAA EQ curve Distortion (THD and IMD): THD @ Main Output, 20 Hz to 20 kHz Mic Input @ 30 dB Gain: Less than 0.
22 d.2 DJ Mixer d.2 2-channel DJ Mix er AC P ower Requir ements: Power Consumption: 20 watts Universal AC Power Supply: 100 V AC – 240 V AC, 50-60 Hz Physical Dimensions and W eight: Height: 15.49”/393.4 mm (including knobs and connectors) W idth: 10"/254 mm Depth: 4.
23 Owner’ s Manual Owner’ s Manual Block Diagram PGM2 Fader Curve Logic Crossfader Curve Logic L R MAIN MAIN LEVEL PAN L BOOTH OUTPUT L Sum R Sum LO MID HI R L MAIN MIX METERS Bal R L R 3-BAND EQ BOOTH LEVEL MONO FireWire I/O FireWire Output (option) ON Assign NO NOTE: Switches are shown in the default (out) position.
24 d.2 DJ Mixer d.2 2-channel DJ Mix er Gain Structure Diagram (+19 dBu max in) MIC CHANNEL EQ LOW XLR I (+13 dB) MI D HIGH TRS 1 +63 dB GAIN = CW +15 dB -15 dB +15 dB -15 dB -3 dB @ center -15 dB to .
25 Owner’ s Manual Owner’ s Manual Appendix D: T ransform Switch Rotation and Fader Replacement T ransform Switch Rotation From the factory , the transform switches operate vertically , that is (to get all technical for a moment) fore and aft.
26 d.2 DJ Mixer d.2 2-channel DJ Mix er Replacing Faders If the faders ever need to be replaced, this can be done with the help of your trusty screwdriver . 10. Follow steps 1 to 5 and remove the top panel. 11. T ake care to only r emove the two outer screws of each fader you are r eplacing, as shown below .
27 Owner’ s Manual Owner’ s Manual A. LOUD T echnologies Inc. warrants all materials, workmanship and proper operation of this product for a period of three years from the original date of purchase.
16220 W ood-Red Road NE • W oodinville, WA 98072 • USA United States and Canada: 800.898.3211 Eur ope, Asia, Central and South America: 425.487 .4333 Middle East and Africa: 31.20.654.4000 Fa x: 425.487 .4337 • www .mackie.com E -mail: sales@mackie.
Ein wichtiger Punkt beim Kauf des Geräts Mackie D-2 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Mackie D-2 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Mackie D-2 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Mackie D-2 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Mackie D-2 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Mackie D-2 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Mackie D-2 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Mackie D-2. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Mackie D-2 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
