Benutzeranleitung / Produktwartung MARK 5X des Produzenten Lowrance electronic
Zur Seite of 28
Installation & Operation manual Elite 5X, Mark 5X, Mark 5X Pr o & Elite 4X Operation manual.
Cop yright © 2011 Navico All rights reserved. Lowranc e ® and Navic o ® ar e registered trademarks of Navico . Navico ma y nd it necessary to change or end our policies, regulations and special oers at an y time. W e reserve the right to do so without notice .
1 T able of Contents Introduction ...................................... 2 Basic Operation ............................... 3 Setup wizard ............................................ 3 Working with menus ................................ 4 Fishing Mode .
2 Introduction Getting Started T urn unit on/off T o turn on/of f the unit, press and hold the LIGHT/ POWER key for three seconds. Adjusting the backlight This unit has 10 backlight levels. Press the LIGHT/ POWER key to switch backlight levels. Muting Audio Select Mute Audio from the System menu and press ENTER .
3 Basic Operation Setup wizard The Setup wizard will appear when the unit is turned on for the rst time. T o choose your own settings, do not run the setup wizard .
4 Basic Operation On/Off features Select an on/o menu item and press ENTER to turn it on/o . Dropdown menus After accessing the dropdo wn menu, press the keypad up/ down to select the desired item and press ENTER . Accessing menu items The keypad and ENTER key are used to select menu items and open submenus.
5 Basic Operation T o input text: 1. Use the keypad to select the desired character and press ENTER . 2. Repeat Step 1 for each character . 3. When entry is completed, highlight OK and press ENTER .
6 Basic Operation Advanced Mode Enables advanced fea tures and settings. The follo wing features are enabled when A dvanced mode is turned on: • Colorline (manual control) • Surface Clarity (manua.
7 Basic Operation Standby mode Low ers power consumption by turning o sonar and the display . Pr ess the PWR/LIGHT key to ac- cess the Backlight menu. Select Standby and press ENTER . Pr ess any key to resume normal op- eration. Restore defaults Resets unit options and settings to defaults.
8 Pages Sonar Page Displays the wat er column moving from right to left on your unit’ s screen. On the right side of the screen, the Amplitude Scope bar preview s echoes about to appear on the display .
9 Pages Overlay Data Displays selected overla y data on the sonar page. Show Enables/disables the display of overla y data, allow- ing you to r emove overlay data fr om the screen without deleting the selected overlay data con- guration. Congure Used to select overlay data t o be displayed on the screen.
10 Pages T o select overlay data: 1. From the sonar page, press MENU . 2. Select Overlay data and press ENTER . 3. Select Congure and press ENTER . 4. Press Menu and select Add . Press ENTER . 5. Select the desired data from the Con- gure Items to show screen.
11 Sonar Move the blue sonar history bar all the way to the right to resume normal sonar scrolling . Pr ess MENU and select Exit cursor mode to re - move the cursor fr om the screen. Sonar Menu The sonar menu has options and settings that aect the appearance of the display .
12 Sonar Pr ess MENU from any sonar page to access the So- nar menu. Adjust (Advanced Mode only) Used to make adjustments to Sensitivity, C olorline and Grayline. Sonar Menu (Advanced Mode) Sensitivity Controls the level of detail shown on the display .
13 Sonar Mark series units have a monochrome display , so wide bands of gray indicat e a hard sonar return, while softer returns are shown as dark, narrow areas . Auto Sensitivity Keeps sensitivity at a level that works w ell under most conditions, r educing the needs for adjust- ments.
14 Sonar Split Flasher Split Zoom Frequency Contr ols the transducer frequency used by the unit. This unit supports t w o frequencies: 200kHz and 83kHz. 200 kHz has the highest sensitivity and best tar- get discrimination in shallow water . 83 kH z o ers a wider cone angle for mor e water cover age.
15 Sonar Fish ID Displays sh echoes as sh sym- bols instead of sh arches . Fish ID is not the most accurate method of sh detection since structure and suspended debris may be shown as a sh symbol on the display .
16 Sonar Overlay Data Allows y ou to selec t data (w a- ter temperatur e, depth, etc) to be displayed on t op of the Sonar screen. Overlay data setup is cov ered in the P ages sec tion.
17 Settings Settings Menu Accesses t o installation and conguration settings for your unit . System Adjusts unit settings like language, mut e audio and advanced mode.
18 Settings Set Language Selects the language used on menus and text box es. Mute Audio T urns on/o unit audio, like key beeps , alarm sounds, etc . Advanced Mode Enables featur es and settings only available with unit in Advanced Mode . Restore Defaults Switches the unit back to default settings.
19 Settings Sonar Used to make adjustments t o Sonar options and display settings like Noise Rejection, Sur face and F ishing Mode. Noise Rejection Uses advanced signal processing to monitor the ef- fects noise (boat pumps, wat er conditions, engine ignition systems , etc.
20 Settings Installation Pr ovides access to Keel Oset and T emp Calibration settings. Keel Offset All transducers measure w ater depth from the transducer to the bottom. A s a result, water depth readings do not accoun t for the distance from the transducer to the keel or fr om the transducer to the water surface.
21 Settings Before setting keel o set, measure the distance from the transducer t o the lowest part of the keel. If, f or example, the keel is 3.5 feet belo w the trans- ducer , it will be input as –3.
22 Index A About 18 Advanced Mode 6 Alarms 21 F ish 21 Shallow 21 Amplitude Scope 15 Auto Sensitivity 13 C Color 15 Colorline 12 Cursor 6 Custom Range 13 D Depth Range 13 Dialogs 5 Dropdown menus 4 F .
Specications Elite 5x, Mark 5x & Mark 5x Pro General Case size 5.4” H (134mm) x 6.8” W (174mm); 6” H (152mm) with bracket Display Mark : (5” diagonal) High-contrast lm Supertwist LCD.
Specications Elite 4x General Case size 5.6” H (144mm) x 3.7” W (94.3mm); 6.4” H (164mm) with bracket Display (3.5” diagonal) 320x240 (256 color) TFT L CD Backlight White LED (10 levels) Power T ransmit power 2100W PTP; 262W RMS Power requirement 12V V oltage input 10 to 17V Current drain at 13.
How to Obtain Service… …in the USA: Contact the F actor y Cust omer Ser vice Department. Call toll-free: 800-324-1356 8 a.m. to 5 p .m. Central Standard Time, M-F Navico may nd it necessary to change or end shipping policies, regulations and special oers at any time .
© Copyright 2011 All Rights Reser ved Navico Holding AS *988-10157-001* Visit our w ebsite: w w w .lo wranc e.c om.
Ein wichtiger Punkt beim Kauf des Geräts Lowrance electronic MARK 5X (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Lowrance electronic MARK 5X noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Lowrance electronic MARK 5X - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Lowrance electronic MARK 5X reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Lowrance electronic MARK 5X erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Lowrance electronic MARK 5X besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Lowrance electronic MARK 5X verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Lowrance electronic MARK 5X. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Lowrance electronic MARK 5X gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
