Benutzeranleitung / Produktwartung EtherFast FENSK05 v2 des Produzenten Linksys
Zur Seite of 39
EtherFast ® Series 10/100 Network In a Bo x Model No.: FENSK05 v2 User Guide.
COPYRIGHT & TRADEMARKS Copyright © 2000 Linksys, All Rights Reserved. EtherFast is a registered trademark of Linksys. Microsoft, Windows, and the Windows logo are r egistered trademarks of Microsoft Corporation. All other trademarks and brand names are the pr operty of their respective proprietors.
Linksys EtherFast ® Series 10/100 Network In a Box Introduction The Linksys EtherFast 10/100 Network In a Box The Linksys 10/100 Netw ork In a Box comes with e verything you need to get a net- w ork up and running in minutes.
10/100 Network In a Box Getting to Know the EtherFast 10/100 Network In a Box The EtherFast 10/100 LAN Card Y ou will install one EtherF ast 10/100 LAN Card into each computer you wish to netw ork.
The Hub’ s Ports 1-5 P orts 1-5 are where you will connect y our PCs to the hub . It is through these ports that network information is exchanged. Uplink Y ou can e xpand your netw ork by connecting your hub to another hub, switch, router or Broadband modem through the Uplink port.
10/100 Network In a Box 5. Once your EtherF ast EtherF ast 10/100 LAN Card is firmly in place , secure its fastening tab to your PC's chassis with a mounting scre w . 6. Replace your PC's co ver . 7. Connect one end of a twisted-pair cable to your PC at the EtherF ast 10/100 LAN Card's RJ-45 por t.
10/100 Network In a Box 9 Windows 98 Installation & Setup Overview After physicall y installing the EtherF ast 10/100 LAN Card in your computer , follo w these instructions to install the network dri ver .
10/100 Network In a Box Linksys EtherFast ® Series 4. Select "Search for the best driv er for your de vice (Recommended). ” Click Next. 5. Select "Floppy disk dri ves".
10/100 Network In a Box 13 Linksys EtherFast ® Series 12 Network Component Configuration 1. Once you are back at the W indo ws 98 desktop, click on your taskbar's Start button, then Settings , then Control P anel , and then doub le-click the Networ k icon.
10/100 Network In a Box 15 Linksys EtherFast ® Series 14 8. Click on the Identif ication tab . T ype the name of your computer in the Computer Name box. Choose a name that is unique from the other com- puter names on the netw ork. 9. T ype the name of your wor kgr oup in the W orkgr oup box.
10/100 Network In a Box 17 Linksys EtherFast ® Series 16 14. A Lo gon windo w will appear , requiring you to enter a User name and P assw ord . Make up a user name and pass w ord (if you ha ven’ t already) and click OK . Do not click the Cancel button or Escape key .
10/100 Network In a Box 19 Linksys EtherFast ® Series 18 Installing the Driver in Windows 95 V ersion B 1. While the Update Device Driver W izard windo w is visib le (previous page), put the EtherF ast Card 10/100 LAN Card Driv er Disk into your flopp y driv e and click Next .
10/100 Network In a Box 21 Linksys EtherFast ® Series 20 Network Component Configuration 1. Once you are back at the W indo ws 95 desktop, click on your taskbar's Start button, then Settings , then Control P anel , and then doub le-click the Networ k icon.
10/100 Network In a Box 23 Linksys EtherFast ® Series 22 8. Click on the Identif ication tab . T ype the name of your computer in the Computer Name box. Choose a name that is unique from the other com- puter names on the netw ork. 9. T ype the name of your w orkgroup in the W or kgr oup box.
10/100 Network In a Box 25 Linksys EtherFast ® Series 11. Optional : Choose the Access Control tab. Ensure that Shar ed-level access contr ol is selected. If the setting is on User-Le vel access control and you can’ t change it, skip to problem 5 in the T roubleshooting section on page 45.
10/100 Network In a Box 27 Linksys EtherFast ® Series 26 3. The Install Hardware Device Driv ers dialog bo x will appear . When Ethernet Contr oller is display ed , select “Search f or a suitab le driver f or your device (Recommended)” . Click Ne xt .
10/100 Network In a Box 7. The Completing the F ound New Hardwar e Wizard dialog box will appear .The follo wing adapter name will be sho wn: Linksys LNE100TX F ast Ethernet Adapter (LNE100TX v4). Click Finish . 8. Remo ve the dri ver disk from the floppy dri ve.
10/100 Network In a Box 31 Linksys EtherFast ® Series 30 3. Click on the Select from list... button to select a netw ork adapter . 4. Click on the Ha v e Disk button. Insert the EtherF ast 10/100 LAN Car d Driver Disk into driv e A. T ype a: into the box on y our screen and hit OK .
10/100 Network In a Box 33 Linksys EtherFast ® Series 32 8. A list of services will appear . Click Next to appro ve these services, fol- lo w ed by Ne xt again. 9. NT will probabl y ask you to suppl y your original Windo ws NT CD-R OM or setup disks.
10/100 Network In a Box 35 Linksys EtherFast ® Series 34 13. Click Finish . When ask ed if you w ant to restart your computer , remo ve the Driv er Disk and click Ye s . 14. Once your PC has rebooted and y ou are logged in, doub le-click the Networ k Neighborhood icon on your desktop.
10/100 Network In a Box 37 Linksys EtherFast ® Series 36 3. When the list of a vailable netw ork adapters appears, click the Ha ve Disk button. 4. Put the EtherF ast Card disk into drive A. T ype a: into the box on y our screen and click OK . 5. Highlight the Linksys LNE100TX F ast Ethernet Adapter (LNE100TX v4) entry in the window that appears.
10/100 Network In a Box 10. Remo ve y our Driv er Disk and CD-R OM and click Ye s to restart your PC. 11. Once your PC has rebooted , double-click the Netw ork Neighborhood icon on your desktop. Ensure that y ou ha ve access to the netw ork. If you do, your card has been properl y installed.
10/100 Network In a Box 41 Linksys EtherFast ® Series 40 5. If the LAN driv er is not located in the default directory , specify the f ile's path on the command line. The LO AD command prompts you for the con- f iguration parameters if they are not supplied on the command line.
10/100 Network In a Box 13. Arrow do wn the list that appears and choose which protocols you w ant to install. Press F10 to sa ve. 14. Highlight Sa v e P arameters and Load Driv er . Press Enter . 15. Y our PC will examine the netw ork. This ma y take a fe w minutes.
10/100 Network In a Box 45 Linksys EtherFast ® Series 44 5. On the Access Control T ab, User Level Access is selected, but Shared Level Access is grayed out and not accessible . • Y ou pre viousl y had your primary netw ork logon set to Client f or NetW are Networ ks .
10/100 Network In a Box 47 Linksys EtherFast ® Series 46 • Click on the IRQ Steering tab . Remo ve the check from Use IRQ Holder and click OK . W indows will ask y ou to restart the PC (if it doesn’t ask you, then reboot the PC manuall y). • After the computer boots up, W indo ws will try to re-detect the PCI Steering.
10/100 Network In a Box 49 Appendix Sharing Y our Files and Printers Overview By sharing your f iles and printers, other PCs on your netw ork will be able to access the resources on your PC. Before sharing your f iles and printers, you should prepare your computer to be used with any f ile servers that may be on the netw ork.
10/100 Network In a Box 51 Linksys EtherFast ® Series 50 Installing the Driver in Windows 95 V ersion A 1. W indows 95 will detect the EtherF ast card and display a Ne w Har dwar e F ound window . 2. Slide the EtherF ast Card Driver Disk into drive A.
10/100 Network In a Box 53 Linksys EtherFast ® Series 52 Windows 98 or 95 Client for Windows NT If you are installing the EtherF ast 10/100 Card in a W indo ws 95 or 98 PC that you plan on lo gging into a NT domain server , follo w the directions belo w .
10/100 Network In a Box 55 Linksys EtherFast ® Series 54 4. Remov e any instance of the name Linksys in the bo x. This includes IPX/SPX…Linksys , NetBEUI…Linksys , and TCP/IP…Linksys . Also remo ve Client for Micr osoft Networ ks , Client for NetW ar e Networ ks , and F ile and Printer Sharing for Micr osoft Networks .
10/100 Network In a Box 57 Linksys EtherFast ® Series 56 Starting Over in Windows 2000 1. Click the Star t button, choose Settings, choose Control Panel, then dou- ble-click the System icon.The System Properties windo w will open. 2. Choose the Hardware tab .
10/100 Network In a Box 59 Linksys EtherFast ® Series 58 Manually Installing the Network Components in Windows 95 & 98 There ma y be times when y ou might need to manually install missing W indo ws netw orking components. 1. Click on Start , Settings , then Control P anel .
10/100 Network In a Box 61 Linksys EtherFast ® Series 60 N N o o t t e e : : Some PME-sup- porting motherboards may not require the WOL wire to be con- nected.
10/100 Network In a Box 63 Linksys EtherFast ® Series 62 Sending a Magic Packet In order to use W OL you need to kno w the MA C address of the card you wish to “wak e”. If you don’ t know the MA C address of the PC y ou are on, turn to page 48 to lear n how to run the EtherF ast Card’ s diagnostic program.
10/100 Network In a Box 65 Linksys EtherFast ® Series 64 No Changes Allowed Y our PC ma y not allo w you to change the IRQ v alue(s) of the PCI slot(s). In this case, you will ONL Y be ab le to use the IRQ and I/O values that ha ve been pre-assigned to each slot.
10/100 Network In a Box 67 Linksys EtherFast ® Series 66 • • S S t t r r a a i i g g h h t t - - T T h h r r o o u u g g h h C C a a b b l l i i n n g g • • C C r r o o s s s s - - O O v v e .
10/100 Network In a Box 69 Linksys EtherFast ® Series 68 10/100 LAN Card Specifications Model Numbers: LNE100TX v4 System: PCI 2.1 (or higher) compliant PC Standards: IEEE 802.
10/100 Network In a Box 71 Linksys EtherFast ® Series 70 Customer Support F or help with the installation or operation of your EtherF ast 10/100 Netw ork in a Box, contact Linksys Customer Support at one of the phone numbers or Internet addresses below .
© Copyright 2000 Linksys, All Rights Reserved. http://www .linksys.com.
Ein wichtiger Punkt beim Kauf des Geräts Linksys EtherFast FENSK05 v2 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Linksys EtherFast FENSK05 v2 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Linksys EtherFast FENSK05 v2 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Linksys EtherFast FENSK05 v2 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Linksys EtherFast FENSK05 v2 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Linksys EtherFast FENSK05 v2 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Linksys EtherFast FENSK05 v2 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Linksys EtherFast FENSK05 v2. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Linksys EtherFast FENSK05 v2 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
