Benutzeranleitung / Produktwartung AV8 des Produzenten Abit
Zur Seite of 80
AV8 AMD Athlon 64™ (FX) System Board Socket 939 User’s Manual 4200-0400-01 Rev. 1.00.
Copyright and Warranty Notice The information in this document is subj ect to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual.
Table Of Contents Chapter 1. Introduction .......................................................................... 1-1 1-1. Features & Specifications ........................................................................ 1-1 1-2. Layout Diagram .
3-9. Load Optimized Defaults ....................................................................... 3-26 3-10. Set Password .......................................................................................... 3-26 3-11. Save & Exit Setup ..
Introduction 1-1 Chapter 1. Introduction 1-1. Features & Specifications 1. CPU • Supports AMD Athlon TM 64 / Athlon TM 64 FX 939-pin processor • 2000MHz system bus using HyperTransport TM technology 2.
1-2 Chapter 1 • 2x USB headers • 2x IEEE 1394 headers • 1x FP-Audio header • 1x CD-IN, 1x AUX-IN header 10. Back Panel I/O • 1x PS/2 keyboard, 1x PS/2 mouse • 1x Serial port connector, 1x .
Introduction 1-3 1-2. Layout Diagram User’s Manual.
1-4 Chapter 1 AV8.
Hardware Setup 2-1 Chapter 2. Hardware Setup Before the Installation: Turn off the power supply switch (fully turn off the +5V standby power), or disconnect the power cord before i nstalling or unplugging any connectors or add-on cards. Failing to do so may cause the motherboard components or add-on cards to malfunction or damaged.
2-2 Chapter 2 2-2. Install CPU and Heatsink This motherboard provid es a ZIF (Zero Insertion Force) Socket 939 to install AMD Socket 939 CPU. The CPU you bought should contain with a kit of heatsink, cooling fan, retention frame and blackplate. If that’s not the case, buy one specially designed for Socket 939.
Hardware Setup 2-3 2-3. Install System Memory This motherboard provides four 184-pin DDR DIMM slots for Sing le/Dual Channel DDR 400/333/266 memory modules with memory expansion size up to 4GB.
2-4 Chapter 2 To reach the performance of Dual Channel DDR, the following rules must be obeyed: • When installing TWO DIMM modules: Install DIMM modules of t he same type and size for slots [DIMM1]+[DIMM2] or slots [DIMM3]+[DIMM4].
Hardware Setup 2-5 2-4. Connectors, Headers and Switches Here we will show you all of the connectors, headers and switches, an d how to connect them. Please read the entire section for necessary inform ation before attempting to finish all the hardwa re installation inside the computer chassis.
2-6 Chapter 2 (2). FAN Connectors These 3-pin connectors each provide power to the cooling fans installed in your system. The CPU must be kept cool by using a powerful fan with heatsink.
Hardware Setup 2-7 (3). CMOS Memory Clearing Header This header uses a jumper cap to clear the CMOS memory. • Pin 1-2 shorted (default): Normal operation. • Pin 2-3 shorted: Clear CMOS memory. WARNING: Turn the power off first (in cluding the +5V standby power) before clearing the CMOS memory.
2-8 Chapter 2 (4). Wake-up Header These headers use a jumper cap to enable/disable the wake-up function. • PS2-PWR1: Pin 1-2 shorted (default): Disable wake-up function support at Keyboard/Mouse port. Pin 2-3 shorted: Enable wake-up function support at Keyboard/Mouse port.
Hardware Setup 2-9 (5). Front Panel Switches & Indicators Headers This header is used for connecting switches and LED indicators on the chassis front panel. Watch the power LED pin position and orientation. The mark “+” align to the pin in the figure below stands for positive polarit y for the LED connection.
2-10 Chapter 2 (6). Additional USB Port Headers These headers each provide 2 addi tional USB 2.0 ports connection th rough an USB cable designed for USB 2.
Hardware Setup 2-11 (7). Additional IEEE1394 Port Headers These headers each provide one ad ditional IEEE1394 port connection through an extension cable and bracket.
2-12 Chapter 2 (8). Front Panel Audio Connection Header This header provides the connection to audio connector at front panel. • To use the audio connector at front panel, remove all the jumpers on this header, and then connect to front panel by the extension cable provided with the chassis.
Hardware Setup 2-13 (9). Internal Audio Connectors These connectors connect to the audio output of internal CD-ROM drive or add-on card. GURU Clock Connection Header (10).
2-14 Chapter 2 (11). Accelerated Graphics Port Slot This slot supports an optional AGP graphics card up to AGP 8X mode. ATTENTION: This motherboard does not support 3.
Hardware Setup 2-15 (12). Floppy Disk Drive Connector This connector supports two standard floppy disk drives via a 34-pin 34-conductor ribbon cable. Connecting the Floppy Disk Drive Cable: 1. Install one end of the ribbon cable into the FDC1 connector.
2-16 Chapter 2 (13). IDE Connectors This motherboard provides two IDE ports to connect up to four IDE drives at Ultra DMA mode by Ultra ATA/66 ribbon cables. Each cable ha s 40-pin 80-conductor and three connectors, providing two hard drives connection with motherboar d.
Hardware Setup 2-17 (14). POST Code Display This is an LED devi ce to display the “ POST ” Code, the acronym of P ower O n S elf T est. The computer will execute the POST action whenever you power on the computer. The POST process is controlled by the BIOS.
2-18 Chapter 2 (15). Serial ATA Connectors These connectors are provided to attach one Serial ATA device at each channel via Serial ATA cable. AV8.
Hardware Setup 2-19 (16). Status Indicators • LED1 (VCC): This LED lights up when the system power is on. • LED2 (5VSB): This LED lights up when the power supply is connected with power source.
2-20 Chapter 2 (17). Back Panel Connectors • Mouse: Connects to PS/2 mouse. • Keyboard: Connects to PS/2 keyboard. • LPT1: Connects to printer or other devices that support this communication protocol. • COM1: Connects to external modem, mouse or other devices that support this communication protocol.
BIOS Setup 3-1 Chapter 3. BIOS Setup This motherboard provides a programmable EEPROM t hat you can update the BIOS utility. The BIOS (Basic Input/Output System) is a pr ogram that deals with the basi c level of communication between processor and peripher als.
3-2 Chapter 3 F6: You may create a profile to save the new BIOS settings in it. Press <F6> button in the main menu, a dialog box with five numbers (1~5) will appear on the screen.
BIOS Setup 3-3 3-1. µGuru Utility Brand Name: This item displays the CPU model name, for example: AMD Athlon TM 64 processor 3400+. Frequency: This item displays the processor speed. CPU Operating Speed: This item displays the CPU operating speed according to the type and sp eed of your CPU.
3-4 Chapter 3 AGP and PCI bus frequency would stay unchangeable at 66MHz and 33MHz. Voltages Control: This option allows you to switch bet ween the default and u ser-defined voltages. Leave this setting to default unless the curren t voltage setting cannot be detected or is not correct.
BIOS Setup 3-5 Back to µGuru Utility Setup Menu: Use < → > key to switch from OC Guru setup menu to ABIT EQ setup menu: ABIT EQ Beep Control: This item allows you to enable or disable ABIT EQ Beep Control function.
3-6 Chapter 3 Shutdown Temp.: This items sets the temperature that would shutdown the system automa tically in order to prevent system overheats. Beep Enable: Use <Space> key to enable warn ing beeps function.
BIOS Setup 3-7 Fan Speed Monitoring: Click <Enter> key to enter its submenu: CPU/NB/SYS/AUX1/AUX2 FAN Speed: These items display the speed of the fans connected to CPU, NB, SYS, AUX1 and AUX2 FAN headers. Shutdown Enable: Use <Space> key to enable system shutdown function.
3-8 Chapter 3 FanEQ Control: Click <Enter> key to enter its submenu: CPU/NB/SYS FanEQ Control: When set to [Enabled], these ite ms allow you to control the CPU/ NB/System fan speed by its setting combination of temperature and voltage high/low limit.
BIOS Setup 3-9 3-2. Standard CMOS Features This section contains the basic configuration parameters of t he BIOS. These paramet ers include date, hour, VGA card, FDD and HDD settings. Date (mm:dd:yy): This item sets the date you specify (usually the current date) in the format of [Month], [Date], and [Year].
3-10 Chapter 3 IDE Channel 1 Master / Slave, IDE Channel 2 Master / Slave: When set to [Auto], the BIOS will au tomatically check what kind of IDE drive you are using. If you want to define your own drive by yourself, set it to [Manual] and make sure you fully unders tand the meaning of the parameters.
BIOS Setup 3-11 [EGA/VGA]: (Enhanced Graphics Adapte r/Video Graphics Array) Fo r EGA, VGA, SVGA and PGA monitor adapters. [CGA 40]: (Color Graphics Adapter) Power up in 40-column mode. [CGA 80]: (Color Graphics Adapter) Power up in 80-column mode. [Mono]: (Monochrome adapter) Includes high-resolution monochrome adapters.
3-12 Chapter 3 3-3. Advanced BIOS Features Hard Disk Boot Priority: This item selects the hard disks boo ting priority. By pressing <Enter> key, you can enter its submenu where the hard disks detected can be selected for the booting sequence to boot up system.
BIOS Setup 3-13 [Setup]: The password is required only when accessing the BIOS Setup. [System]: The password is required each time the computer boots up. NOTE: Don’t forget your passw ord. If you forget the password, you will have to open the computer case and clear all information in the CM OS before you can start up the sy stem.
3-14 Chapter 3 3-4. Advanced Chipset Features AGP & P2P Bridge Control: Click <Enter> key to enter its submenu: AGP Aperture Size: This option specifies the amount of system memory that can be used by the AGP device. The aperture is a portion of the PCI memory address range dedicated for graphics memory address space.
BIOS Setup 3-15 AGP Fast Write: Two options are available: Disabled Enabled. The default setting is Enabled . If your AGP adapter can support this function, then you can choose Enabled . Otherwise, choose Disabled . AGP Master 1 WS Write: Two options are available: Disabled Enabled.
3-16 Chapter 3 DRAM Timing Selectable: Two options are available: Manual By SPD. The default setting is By SPD . When set to “ By SPD ”, the BIOS will read the DRAM module SPD data and automatically set to the values stored in it. DRAM Clock: This item sets the DRAM clock of your DRAM module.
BIOS Setup 3-17 Back to Advanced Chipset Features Setup Menu: LDT & PCI Bus Control: Click <Enter> key to enter its submenu: Upstream/Downstream LDT Bus Width: This item allows you to select LDT Bus Width. LDT Bus Frequency: This item allows you to select LDT Bus Frequency.
3-18 Chapter 3 3-5. Integrated Peripherals OnChip IDE Device: Click <Enter> key to enter its submenu: SATA RAID ROM: This item allows you to use the boot ROM of on-chip Serial ATA RAID to boot-up system. IDE Bus Master: This option enables or disables the IDE bus mastering capability under the DOS environment.
BIOS Setup 3-19 Back to Integrated Peripherals Setup Menu: OnChip PCI Device: Click <Enter> key to enter its submenu: OnChip Audio Controller: This option enables or disables the audio controller. Onboard LAN Controller: This option enables or disables the LAN controller.
3-20 Chapter 3 Back to Integrated Peripherals Setup Menu: SuperIO Device: Click <Enter> key to enter its submenu: Onboard FDD Controller: Two options are available: Enabled an d Disabled. The de fault setting is Enabled . You can enable or disable the onboard FDD controller.
BIOS Setup 3-21 3-6. Power Management Setup ACPI Suspend Type: This item selects the type of Suspend mode. [S1(PowerOn-Suspend)]: Enables the Power On Suspend function. [S3(Suspend-To-RAM)]: Enables the Suspend to RAM function. Run VGABIOS if S3 Resume: Three options are available: Auto Yes No.
3-22 Chapter 3 [Power Off]: When power returns after an AC power failure, the system’s power remains off. You must press the Power button to power-on the system. [Power On]: When power returns after an AC power failu re, the system’s power will be powered on automatically.
BIOS Setup 3-23 NOTE: To enable this “Power On” function, the wake-up header of [PS2-PWR 1], [USB-PWR1] and [USB-PWR2] must be set to [Enabl ed] position. Please refer to the co nfiguration of “W ake-up Header” in section 2-4, chapter 2. The mouse wake up function can only be used with the PS/2 mouse, no t with the COM port or USB type.
3-24 Chapter 3 3-7. PnP/PCI Configurations Resources Controlled By: This item configures all of the boot and Plug-and-Play compatible devices. [Auto]: The system will automatically detect the settings. [Manual]: Choose the specific IRQ resources in the “IRQ Resources” menu.
BIOS Setup 3-25 PIRQ_0 Use IRQ No. ~ PIRQ_7 Use IRQ No.: This item specifies the IRQ number manually or automatically for the devices installed on PCI slots.
3-26 Chapter 3 3-8. Load Fail-Safe Defaults This option loads the BIOS default values for the most stable, minimal-performance system operations. 3-9. Load Optimized Defaults This option loads the BIOS defau lt values that are fact ory settings for optima l-performance system operations.
Install VIA 4-in-1 Driver A-1 Appendix A. Install VIA 4-in-1 Driver NOTE: Please install this VIA 4-in-1 driver first after having installed the Windows operating system. The installation procedur es and screen shots in this section are based on Windows XP operating system.
A-2 Appendix A Click [Next]. 6. 7. Choose [Yes, I want to restart my computer now.], and click [OK] to complete setup. AV8.
Install Audio Driver B-1 Appendix B. Install Audio Driver The installation procedur es and screen shots in this section are based on Windows XP operating system. For those of othe r OS, please follow its on-screen instruction. Insert the Driver & Utility CD into CD-ROM drive, it should execute the installation program automatically.
B-2 Appendix B B-2 Appendix B AV8 AV8.
Install LAN Driver C-1 Appendix C. Install LAN Driver To install the LAN driver, please insert the Driver & Utility CD into CD-ROM drive. It should execute the installation progra m automatically. If not, double-click the execu tion file at the main directory of this CD to enter the installation menu.
C-2 Appendix C AV8.
Install VIA USB 2.0 Driver D-1 Appendix D. Install VIA USB 2.0 Driver NOTE: There is no need to install VIA USB 2.0 driver for the Wind ows XP operatin g system with Service Pack 1 already installed. Please run the Windows update for the latest Service Pack.
D-2 Appendix D Click [Yes]. 6. Click [OK]. 7. Click [Print to File]. 8. Click [OK]. 9. AV8.
Install VIA Serial ATA RAID Driver E-1 Appendix E. Install VIA Serial ATA RAID Driver The installation procedur es and screen shots in this section are based on Windows XP operating system. For those of othe r OS, please follow its on-screen instruction.
E-2 Appendix E 6. Choose [Yes, I want to restart my computer now.], and click [Finish] to complete setup. 7. After the system restarted, a shortcut icon appears at the right corner of Windows task bar. 8. This is the “VIA RAID Tool” configuration menu.
Install ABIT µGuru Driver F-1 Appendix F. Install ABIT µGuru Driver ABIT µGuru is a fresh Microproce ssor developed by ABIT engineers used only on ABIT motherboards.
F-2 Appendix F AV8.
POST Code Definition G-1 Appendix G. POST Code Definition AWARD POST Code Definition: POST (hex) Description CF Test CMOS R/W functionality C0 Early chipset initialization: -Disable shadow RAM -Disabl.
G-2 Appendix G 1F Load keyboard matrix (notebook platform) 21 HPM initialization (notebook platform) 23 1. Check validity of RTC value: e.g. a value of 5Ah is an invalid value for RTC minute. 2. Load CMOS settings into BIOS stack. If CMOS checksum fails, use default value instead.
POST Code Definition G-3 55 Display number of processors (multi-processor platform) 57 Display PnP logo Early ISA PnP initialization -Assign CSN to every ISA PnP device 59 Initialize the combined Trend Anti-Virus code 5B (Optional Feature) Show message for entering AWDFLASH.
G-4 Appendix G 8B 1. Invoke all ISA adapter ROMs 2. Invoke all PCI ROMs (except VGA) 8D 1. Enable/Disable Parity Check according to CMOS setup 2. APM Initialization 8F Clear noise of IRQs 93 Read HDD boot sector information for Trend Anti-Virus code 94 1.
POST Code Definition G-5 AC2003 POST Code Definition: POST (hex) Description Power On Sequence 8.1. Start power on sequence 8.2. Enable ATX power supply 8.3. ATX power supply ready 8.4. DDR voltage ready 8.5. Setup PWM for CPU core voltage 8.6. Assert PWM for CPU core voltage 8.
G-6 Appendix G AV8.
Troubleshooting (Need Assistance?) H-1 Appendix H. Troubleshooting (Need Assistance?) Q & A: Q: Do I need to clear the CMOS before I use a new motherboard to ass emble my new computer system? A: Yes, we highly recommend that you clear the CMOS before installing a new motherboard.
H-2 Appendix H Q: How can I get a quick response to my request for technical support? A: Be sure to follow the guidelines as stated in the “Technical Support Form” section of this manual.
Troubleshooting (Need Assistance?) H-3 Main instructions: To fill in this “ Technical Support Form ”, refer to the step-by-step instructions given below: 1 * .
H-4 Appendix H Technical Support Form Company Name: Phone Number: Contact Person: Fax Number: E-mail Address: Model * BIOS ID # * Motherboard Model No.
How to Get Technical Support I-1 Appendix I. How to Get Technical Support (From our website) http://www.abit.com.tw (In North America) http://www.abit-usa.com (In Europe) http://www.abit.nl Thank you for choosing ABIT products. ABIT sells all our products through distributors, resellers and system integrators; we have no direct sales to end-users.
I-2 Appendix I 4. Internet Newsgroups. They are a great source of information and many people there can offer help. ABIT's Internet News group, alt.comp.periphs.mainboard.abit , is an ideal forum for the public to exchange informati on and discuss experiences they have had with ABIT products.
How to Get Technical Support I-3 North America and South America: ABIT Computer (U.S.A.) Corporation 45531 Northport Loop West, Fremont, California 94538, U.S.A. Tel: 1-510-623-0500 Fax: 1-510-623-1092 sales@abit-usa.com technical@abit-usa.com http://www.
I-4 Appendix I 7. RMA Service. If your system has been working but it just stopped, but you have not installed any new software or hardware recen tly, it is likely that you have a defective component. Please contact the reseller from whom you bought the product.
Ein wichtiger Punkt beim Kauf des Geräts Abit AV8 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Abit AV8 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Abit AV8 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Abit AV8 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Abit AV8 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Abit AV8 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Abit AV8 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Abit AV8. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Abit AV8 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
