Benutzeranleitung / Produktwartung 2009 MKS des Produzenten Lincoln
Zur Seite of 323
Introduction 4 Instrument Cluster 10 W arning lights and chimes 10 Gauges 14 Entertainment Systems 16 AM/FM stereo with CDX6/MP3 16 Auxiliary input jack (Line in) 23 USB port 25 Satellite radio inform.
Locks and Security 91 Keys 91 Locks 94 Anti-theft system 113 Seating and Safety Restraints 120 Seating 120 Safety restraints 131 Airbags 144 Child restraints 159 Tires, Wheels and Loading 176 T ire in.
Customer Assistance 264 Reporting safety defects (U.S. only) 270 Reporting safety defects (Canada only) 271 Cleaning 272 Maintenance and Specifications 279 Engine compartment 281 Engine oil 283 Batter.
CONGRATULATIONS Congratulations on acquiring your new Lincoln. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it.
Protecting the environment W e must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubrication materials are significant steps towards this aim. Information in this respect is highlighted in this guide with the tree symbol.
Special instructions For your added safety , your vehicle is fitted with sophisticated electronic controls. W ARNING: Please read the section Airbag Supplemental Restraint System (SRS) in the Seating and Safety Restraints chapter . Failure to follow the specific warnings and instructions could result in personal injury .
other government authorities or other third parties acting with lawful authority . Other parties may seek to access the information independently of Ford Motor Company and Ford of Canada. Cell phone use The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs.
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Lower Anchor Child Seat.
V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant T emper.
W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause extensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulbs work.
W ARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter , the fuel system, interior floor coverings or other vehicle components, possibly causing a fire.
Safety belt: Reminds you to fasten your safety belt. A Belt-Minder 威 chime will also sound to remind you to fasten your safety belt. Refer to the Seating and Safety Restraints chapter to activate/deactivate the Belt-Minder 威 chime feature. Charging system: Illuminates when the battery is not charging properly .
information on this system, refer to T ire pressure monitoring system (TPMS) in the T ires, Wheels and Loading chapter . Adaptive cruise control (ACC) (if equipped): Illuminates when there is a vehicle in front of you. Speed control: Illuminates when the speed control is engaged or when the ACC is engaged without following a vehicle.
High beams: Illuminates when the high beam headlamps are turned on. Key-in-ignition warning chime (if equipped): Sounds when the key is left in the ignition in the off or accessory position and the driver’ s door is opened.
W ARNING: Never remove the coolant reservoir cap while the engine is running or hot. Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is on). The fuel gauge may vary slightly when the vehicle is in motion or on a grade.
AUDIO SYSTEMS Premium/Audiophile AM/FM in-dash CD6/MP3 satellite compatible sound system W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road.
AM/FM Radio / VOL (Power/V olume): Press to turn the radio on/off. T urn the knob to increase/decrease volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a nominal listening level when the ignition is turned back on.
CA T/FLD (Category/Folder): This feature allows you to select from various music categories. T o change RDS categories: Press MENU repeatedly until RDS ON/OFF appears in the display . Use SEEK to toggle RDS to ON. Press CA T . PRESS UP OR DOWN TO CHANGE RDS CA TEGORY will appear in the display .
CA T (Category) / FLD (Folder): In MP3 mode only– Press CA T/FOLD and then press SEEK to access the previous/next folder . SCAN: Press for a brief sampling of all tracks on the current disc or MP3 folder . DIRECT : In CD mode– Press DIRECT . The display will read DIRECT TRACK MODE SELECT TRACK.
DIRECT : Press DIRECT then enter the desired channel (i.e. 002) using the memory preset buttons (0–9). If you only enter one digit, press OK and the system will go to that satellite channel. If you enter three digits, the system will automatically go to that channel, if available.
channel Categories (Pop, Rock, News, etc.) Press OK when the desired category appears in the display . After a category is selected, press SEEK to search for that specific category of channels only (i.e. ROCK). Y ou may also select CA TEGORY ALL to seek all available SIRIUS categories and channels.
• CHANNEL LOCKOUT MENU- Press OK to enter the Channel Lockout menu. Press the SEEK to scroll through the following options: a. LOCK/UNLOCK THIS CHANNEL: Press OK when LOCK/UNLOCK THIS CHANNEL is displayed and the display will read ENTER PIN.
Use SEEK to adjust between SPEED OFF and levels 1–7: Increasing the level from 1 (lowest setting) to 7 (highest setting) allows the radio volume to automatically change slightly with vehicle speed to compensate for road and wind noise. Recommended level is 1–3; SPEED OFF turns the feature off and level 7 is the maximum setting.
The Auxiliary Input Jack provides a way to connect your portable music player to the in-vehicle audio system. This allows the audio from a portable music player to be played through the vehicle speakers with high fidelity .
compatible with the AIJ. The AIJ will only work correctly with devices that have a headphone output with a volume control. 2. Do not set the portable music player’ s volume level higher than is necessary to match the volume of the CD or FM radio in your audio system as this will cause distortion and will reduce sound quality .
GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and T elecommunications Commission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.
CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only . Due to technical incompatibility , certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Do not use any irregular shaped CDs or discs with a scratch protection film attached.
• MP3 folder mode represents a folder structure consisting of one level of folders. The CD player numbers all MP3 tracks on the disc (noted by the .mp3 file extension) and all folders containing MP3 files, from F001 (folder) T001 (track) to F253 T255.
Satellite radio reception factors: T o receive the satellite signal, your vehicle has been equipped with a satellite radio antenna located on the roof of your vehicle. The vehicle roof provides the best location for an unobstructed, open view of the sky , a requirement of a satellite radio system.
Radio Display Condition Action Required ACQUIRING Radio requires more than two seconds to produce audio for the selected channel. No action required. This message should disappear shortly .
Radio Display Condition Action Required NO TEXT Category information not available. Category information not available at this time on this channel. The system is working properly . NO SIGNAL Loss of signal from the SIRIUS satellite or SIRIUS tower to the vehicle antenna.
DUAL ZONE AUTOMATIC T EMPERATURE CONTROL WITH HEATED AND COOLED SEATS T emperature conversion: T o switch between Fahrenheit and Celsius, refer to Message center in the Driver Controls chapter . 1. : Distributes outside air through the windshield defroster vents and de-mister vents.
4. : Distributes air through the instrument panel vents, floor vents, rear seat floor vents and de-mister vents. T o return to full automatic control, press AUTO. 5. : Distributes air through the instrument panel vents. T o return to full automatic control, press AUTO.
11. A U T O/+– (Fan Speed Control): Press to engage automatic temperature control. Select the desired temperature using the temperature control. The system will automatically determine fan speed, airflow location, A/C on or off, and outside or recirculated air , to heat or cool the vehicle to reach the desired temperature.
DUAL ZONE AUTOMATIC T EMPERATURE CONTROL WITH HEATED AND COOLED SEATS (NAVIGATION SYSTEM BASED–IF EQUIPPED) T emperature conversion: T o switch between Fahrenheit and Celsius, refer to Message center in the Driver Controls chapter . 1. Climate: Press to control the climate control system through the touch display screen.
5. R Rear defroster: Press to activate/deactivate the rear window defroster . Refer to Rear window defroster later in this chapter for more information. This button will also activate the heated mirrors. 6. Defrost: Distributes outside air through the windshield defroster vents and de-mister vents.
T OUCHSCREEN FUNCTIONS T emperature conversion: T o switch between Fahrenheit and Celsius, refer to Message center in the Driver Controls chapter . T emperature – Press the up and down arrows on the left side of the screen to increase/decrease the airflow temperature for the driver side of the vehicle.
V OICE COMMANDS IN CLIMATE MODE Please refer to the V oice commands in climate mode section of the Navigation system supplement for more information on using voice commands with the climate control system. Operating tips • T o reduce fog build up on the windshield during humid weather , place the air flow selector in the position.
T o aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan to the highest speed.
HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the low beam headlamps on. Adaptive headlamps (if equipped) The headlamp beams move in the same direction as the steering wheel to provide more visibility when driving around curves.
The autolamp system also keeps the lights on for a predetermined amount of time after the ignition is turned off. Y ou can change the amount of time the lamps stay on by using the programming procedure that follows: Note: W ith autolamps, your vehicle has a headlamps on with windshield wipers feature.
High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate. Auto high beams (if equipped) The automatic high beam system uses a windshield mounted camera to monitor surrounding traffic conditions and high beam usage.
Scenario 3: Conditions - The automatic high beam system is set to ON in the message center . The headlamp switch is in (off), (park lamps), or (on). Operation - The high beam switch can be used to turn the high beams on and off. Scenario 4: Conditions - The automatic high beam system is set to OFF in the message center .
• The vehicle speed falls below 27 mph (43 km/h). • The ambient light level is high enough that high beams are not needed. • Severe rain, snow or fog is detected.
T roubleshooting If the automatic high beam camera becomes blocked, the high beams will not come on automatically . They will only activate when they are manually turned on with the multi-function lever . T ypical road dust, dirt and water spots will not affect the automatic high beam system’ s performance.
P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parking lamp operation. Move the control to the full upright position, past detent, to turn on the interior lamps.
4. On the wall or screen you will observe an area of high intensity light. The top of the high intensity area should touch the horizontal reference line, if not, the beam will need to be adjusted using the next step. 5. Locate the vertical adjuster on each headlamp.
INTERIOR LAMPS Second row map lamps The second row lamps are located at the rear of the headliner above each outboard seat. The second row lamps light when: • any door is opened, • the instrument panel dimmer switch is rotated up until the courtesy lamps come on, and • any of the remote entry controls are pressed and the ignition is off.
Function Number of bulbs T rade number License plate lamp 2 168 * High-mount brake lamp 1 LED Fog lamp (if equipped) 2 H11 Map lamp 2 12V6W Dome/reading lamps 3 578 T o replace all instrument panel lights, see your authorized dealer . * T o replace these lamps, see your authorized dealer .
Replacing rear brake/tail/turn and sidemarker lamp bulbs The brake/tail/turn/side marker lamp and backup bulbs are located in the tail lamp assembly . Follow the same steps to replace the bulbs.
Replacing license plate lamp bulbs 1. Make sure the headlamp switch is in the off position. 2. Remove the two screws from the license plate lamp assembly . 3. Remove bulb socket by turning counterclockwise. 4. Carefully pull the bulb out from the socket.
MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate toward you to decrease the speed of the wipers.
Windshield wiper rainlamp feature When the windshield wipers are turned on during daylight, and the headlamp control is in the autolamp position, the exterior lamps will turn on after a brief delay and will remain on until the wipers are turned off.
Slide on rod feature Rotate the visor towards the side window and extend it rearward for additional sunlight coverage. Note: T o stow the visor back into the headliner , visor must be retracted before moving it back toward the windshield.
CENTER CONSOLE Y our vehicle may be equipped with a variety of console features. These include: 1. Cupholders 2. Driver and passenger arm rests that slide forward or rearward and also opens the utility compartment that has an audio input jack, USB port and power point inside.
fuse may have blown. Refer to Fuses and relays in the Roadside Emergencies chapter for information on checking and replacing fuses. T o have full capacity usage of your power point, the engine is required to be running to avoid unintentional discharge of the battery .
control on the remote transmitter . Refer to the Locks and Security chapter for the Opening and closing all windows and moon roof feature. Rear W indow Buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or buffeting noise.
Window lock The window lock feature allows only the driver to operate the power windows. T o lock out all the window controls (except for the driver’ s) press the right side of the control.
day/night mirrors will change from the normal (high reflective) state to the non-glare (darkened) state when bright lights (glare) reach the interior mirror .
Heated outside mirrors Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors.
3. Press the SET + or SET - control and release it. 4. T ake your foot off the accelerator pedal. 5. The indicator light on the instrument cluster will turn on.
Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. Y ou can also use the SET + control to operate the T ap-Up function.
Turning of f speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle’ s previously set speed. • Press the speed control OFF control. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.
W ARNING: Adaptive cruise control is not a collision warning or avoidance system. Additionally , adaptive cruise control will not detect: • Stationary or slow moving vehicles below 6 mph (10 km/h). • Pedestrians or objects in the roadway . • Oncoming vehicles in the same lane.
3. Press and release the SET + control. The vehicle speed will be stored in the memory and the message center will display SET XXX MPH (your desired speed).
Note: If the ACC system predicts that its maximum braking level will not be sufficient, then an audible warning will sound while the ACC continues to brake. This is accompanied by DRIVER INTERVENE displayed in the message center . The driver should take immediate action.
Disengaging adaptive cruise control T o disengage the adaptive cruise control: • Depress the brake pedal. CRUISE CANCELLED will be displayed in the message center .
Resuming the set speed Press and release the RESUME control. This will automatically return the vehicle to the previously set speed. The set speed will display continuously in the message center while ACC is active. Note: RESUME should only be used if the driver is aware of the set speed and intends to return to it.
Turning of f cruise control T o turn off the cruise control: • Press the OFF control. Note: When you turn off the cruise control or the ignition, your cruise control set speed memory is erased. Detection issues The radar sensor has a limited field of vision.
• There may be issues with the detection of vehicles in front when driving into and coming out of a bend or curve in the road. In these cases ACC may brake late or unexpectedly .
Cause Action The surface of the radar in the grille is dirty or obstructed in some way Clean the grille surface in front of the radar or remove the object causing the obstruction The surface of the radar in the grille is clean but the message remains in the display W ait a short time.
STEERING WHEEL CONTROLS Radio control features Press MEDIA to select: • AM, FM1, FM2, or CD • SA T1, SA T2 or SA T3 (Satellite Radio mode). • LINE IN (Auxiliary input jack) In Radio mode: • Press to access the next/previous preset station. In CD mode: • Press to listen to the next track on the disc.
SYNC system hands free control feature Press briefly to use the voice command feature. Y ou will hear a tone and LISTENING will appear in the radio display . Press and hold to exit voice command. Press to activate phone mode or answer a phone call. Press and hold to end call or exit phone mode.
The dual panel moon roof and power sunscreen are equipped with an automatic, one-touch, express opening and closing feature. T o stop motion at any time during the one-touch operation, press the control a second time. T o open the sunscreen: Press the control.
T o vent the dual panel moon roof: Press and quickly release the TIL T control (moon roof is equipped with, automatic, one-touch, tilt open feature). The moon roof must be in the closed position in order to move it into the vent position.
Programming Do not program HomeLink 威 with the vehicle parked in the garage. Note: Y our vehicle may require the ignition to be turned on for programming and/or operation of the HomeLink 威 .
press/hold/release sequence again and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink 威 should now activate your rolling code equipped device.
Erasing HomeLink 姞 buttons T o erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink 威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds.
Selectable features Reset Press this control to select and reset functions shown in the INFO menu and SETUP menu. Info menu This control displays the following control displays: • T rip Odometer A o.
Average fuel economy (AFE) Select this function from the INFO menu to display your average fuel economy in miles/gallon or liters/100 km. If you calculate your average fuel economy by dividing 100 mil.
2. Press and hold RESET for two seconds to reset the timer . Setup menu Press this control for the following displays: • System Check • Oil Life • Units (English/Metric) • Auto high beam (if e.
9. ADAPTIVE CRUISE CONTROL (if equipped) 10. P ARK AID 11. FUEL LEVEL Oil life An oil change is required whenever indicated by the message center . USE ONL Y RECOMMENDED ENGINE OILS. T o reset the oil monitoring system to 100% after each oil change (approximately 7,500 miles [12,000 km] or six months) perform the following: 1.
1. T o disable/enable the auto high beam feature, select this function from the SETUP menu for the current display mode. 2. Press the RESET control to turn the auto high beam ON or OFF . Autolamp delay This feature keeps your headlights on for up to three minutes after the ignition is switched off.
1. T o disable/enable the easy entry seat feature, select this function from the SETUP menu for the current display mode. 2. Press the RESET control to turn the easy entry seat ON or OFF .
In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for several seconds.
W arnings Status Integrated key programming status (if equipped) Maximum number of Integrated Keys exceeded Cruise On (if equipped) Adaptive Cruise Control warnings Cruise Off (if equipped) Set speed .
REAR LEFT DOOR AJAR — Displayed when the rear left door is not completely closed. REAR RIGHT DOOR AJAR — Displayed when the rear right door is not completely closed. P ARK BRAKE ENGAGED — Displayed when the manual park brake is set, the engine is running and the vehicle is driven more than 3 mph (5 km/h).
TRUNK AJAR — Displayed when the trunk is not completely closed. REMOVE OBJECTS NEAR P ASS SEA T — Displayed when objects are by the passenger seat. After the objects are moved away from the seat, if the warning stays on or continues to come on contact your authorized dealer .
PRESS BRAKE TO ST AR T (if equipped) — Displayed when the start/stop button is pressed without the brake pedal being applied. This is a reminder that the brake pedal must be applied when the start/stop button is pressed in order to start the engine.
INTERIOR TRUNK CONTROL Press the remote trunk release control on the instrument panel to the left of the steering wheel. CARGO AREA FEATURES Cargo net (if equipped) The cargo net secures lightweight objects in the cargo area. Attach the net to the anchors provided.
KEYS Integrated Keyhead T ransmitters (IKT s) (If equipped) Y our vehicle may be equipped with two Integrated Keyhead T ransmitters (IKT s). The key blade of the IKT functions as a programmed key which starts the vehicle and unlocks/locks all the doors.
Recommended handling of the Integrated Keyhead T ransmitter (IKT) T o avoid inadvertently activating the remote entry functions of your vehicle, it is recommended that the Integrated Keyhead T ransmitter (IKT) be handled properly when starting and turning off your vehicle.
Intelligent Access Key (IA Key) (if equipped) Y our vehicle may be equipped with two Intelligent Access Keys which operate the Intelligent Access Key with Push Button Start systems and the remote entry system. The Intelligent Access Key also contains a removable mechanical key blade that can be used to unlock the driver door .
POWER DOOR LOCKS • Press the control to unlock all doors. • Press the control to lock all doors. Smart unlocks This feature helps to prevent you from locking yourself out of the vehicle if your key is still in the ignition.
trunk. When the alarm is armed, if the Intelligent Access Key is detected in the trunk, the decklid will automatically be released when you attempt to close it, and the horn will chirp, as a reminder that the Intelligent Access Key is inside.
W ARNING: Before operating power windows and moon roofs, you should verify that they are free of obstructions and ensure that children and/or pets are not in the proximity of window openings.
Power door lock switch autolock enable/disable procedure Before starting, ensure the ignition is off and all vehicle doors are closed. Y ou must complete Steps 1–5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, wait a minimum of 30 seconds before beginning again.
Autounlock feature The autounlock feature will unlock all the doors when: • the ignition is on, all the doors are closed, and the vehicle has been in motion at a speed greater than 12 mph (20 km/h);.
6. T o enable/disable the autounlock feature, press the lock control, then press the unlock control. The horn will chirp once if autounlock was deactivated or twice (one short and one long chirp) if autounlock was activated. 7. T urn the ignition off.
CHILDPROOF DOOR LOCKS • When these locks are set, the rear doors cannot be opened from the inside. • The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door .
T o open the luggage compartment door (lid) from within the luggage compartment, pull the illuminated “T” shaped handle and push up on the trunk lid. The handle is composed of a material that will glow for hours in darkness following brief exposure to ambient light.
REMOTE ENTRY SYSTEM The Integrated Keyhead T ransmitters (IKT s) and Intelligent Access Keys comply with part 15 of the FCC rules and with RSS-210 of Industry Canada.
• structures around the vehicle, or • other vehicles parked next to your vehicle. The transmitter allows you to: • remotely unlock the vehicle doors. • remotely lock all the vehicle doors. • remotely open the trunk. • activate the personal alarm.
( Note: If two stage unlocking is disabled, all doors will unlock when you press any button on the keyless entry keypad). Activating Intelligent Access at the T runk: If your Intelligent Access Key is.
The battery saver feature will turn off the interior lamps 10 minutes after the ignition is turned off. T wo stage unlocking may be disabled or re-enabled by simultaneously pressing the and controls on the transmitter for four seconds (disabling two stage unlock allows all vehicle doors to unlock simultaneously).
Memory seats/power mirrors/steering column The Integrated Keyhead T ransmitter IKT or Intelligent Access Key allows you to recall the memory seat/power mirrors/steering column feature. Press on the transmitter or activate the Intelligent Access feature to automatically move the seat, mirrors and steering column to the desired memory position.
T o replace the battery: Integrated Keyhead T ransmitter 1. T wist a thin coin in the slot near the key ring to remove the battery cover . 2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery .
2. Do not wipe off any grease on the battery terminals or on the back surface of the circuit board. 3. Remove the old battery . Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery . Refer to the instructions inside the Intelligent Access Key for the correct orientation of the battery .
• the control on the transmitter is pressed, or • the vehicle is locked using the keyless entry keypad, or • the vehicle is locked using the key in the driver door cylinder , or • after 25 seconds of illumination. The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open.
1. T urn the ignition on. 2. Press the power door unlock control on the door panel three times. 3. T urn the ignition off. 4. Press the power door unlock control on the door panel three times. 5. T urn the ignition back on. The horn will chirp one time to confirm programming mode has been entered and is active.
SECURICODE™ KEYLESS ENTRY SYSTEM The keypad, located near the driver’ s window , is invisible until touched and then it lights up so you can see and touch the appropriate buttons. Y ou can use the keyless entry keypad to: • lock or unlock the doors without using a key .
Note: T ouching 5 • 6 ,7 • 8 ,o r9 • 0 keypad numbers as a sixth digit will not recall a driver memory setting. Note: The factory-set code cannot be associated with a memory setting. 5. The doors will lock then unlock to confirm that your personal entry code has been programmed to the module.
Note: If equipped with Intelligent Access, if the Intelligent Access Key is within 3 feet (1 meter) of the driver door , your keyless entry keypad code will still function the same way , but the driver’ s door will also unlock with each keypad button press.
Anti-theft indicator (If equipped) The anti-theft indicator is located in the instrument panel cluster . • When the ignition is off, the indicator will flash once every two seconds to indicate the SecuriLock™ system is functioning as a theft deterrent.
Button Start systems as well as a remote keyless entry transmitter . A maximum of four Intelligent Access Keys can be programmed to your vehicle. If your programmed transmitters or standard SecuriLock.
5. T urn the ignition from off to on. Keep the ignition on for at least three seconds, but no more than 10 seconds. 6. T urn the ignition off and remove the second previously programmed coded key from the ignition.
exactly as described below , and perform all steps within 30 seconds of starting the sequence. If any steps are performed out of sequence, stop and wait for at least one minute before starting again. Please read and understand the entire procedure before you begin.
The system is ready to arm whenever the ignition is off. Any of the following actions will prearm the alarm system: • Press the control on the transmitter . When you press the lock control twice within three seconds on your transmitter , the horn will chirp once to let you know that all doors, the hood and the trunk are closed.
• Unlock the driver door or all doors using the Intelligent Access (if equipped). • Unlock the driver’ s door with a key . T urn the key toward the rear of the vehicle to make sure the alarm disarms. • T urn ignition on. • Press the control on the transmitter .
SEATING W ARNING: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. W ARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
T o adjust the head restraint, do the following: 1. Adjust the seatback to an upright driving/riding position. 2. Raise the head restraint by pulling up on the head restraint. 3. Lower the head restraint by pressing and holding the guide sleeve adjust/release button and pushing down on the head restraint.
T o remove the adjustable head restraint, do the following: 1. Pull up the head restraint until it reaches the highest adjustment position. 2. Simultaneously press and hold both the adjust/release button and the unlock/remove button, then pull up on the head restraint.
W ARNING: T o minimize the risk of neck injury in the event of a crash, head restraints must be installed properly . Adjusting the front power seat W ARNING: Never adjust the driver’ s seat or seatback when the vehicle is moving. W ARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
Press the front portion to tilt the seat. Press the control to move the seat forward, backward, up or down. Press the control to recline the seatback forward or rearward.
Using the power lumbar support The lumbar control is located on the side of the seat cushion. Press the front of the control to adjust firmness. Press the rear of the control to adjust softness. Press the top of the control to raise the height of the lumbar support.
T o operate the heated seats: Press once to activate the high heat setting (three indicator lights). Continue pressing to scroll through the other settings; medium heat (two indicator lights), low heat (one indicator light) or off.
T o remove an air filter: 1. Remove key from ignition. 2. Push up on the outside rigid edge of the filter until the tabs are released, then rotate the air filter toward the front of the vehicle.
Memory seats/power mirrors/steering column This system allows automatic positioning of the driver seat, power mirrors, and steering column to two programmable positions.
The seat and steering wheel will move to the original position when: • the transmission is in N (Neutral) or P (Park) • the key is placed in the ignition cylinder or when the push button start system (if equipped) is put in accessory mode (refer to Push button start system in the Driving chapter).
Armrest pass-through Pull down the door located in back of the armrest in order to store cargo of a longer length such as skis or lumber . Note : Do not exceed 80 lb (36 kg) of weight on the pass-through door .
Note: Do not do the following: • Place heavy objects on the seat • Operate the seat heater if water or any other liquid is spilled on the seat. Allow the seat to dry thoroughly . The heated seat control is on the back of the front center console. T o operate the heated seats: • Push the indicated side of the control for maximum heat.
Y our vehicle’ s Personal Safety System™ consists of: • Driver and passenger dual-stage airbag supplemental restraints. • Front outboard safety belts with pretensioners, energy management retractors (first row only), and safety belt usage sensors.
Front crash severity sensor The front crash severity sensor enhances the ability to detect the severity of an impact. Positioned up front, it provides valuable information early in the crash event on the severity of the impact.
restrain children in the rear seat. The sensor also turns off the passenger front airbag and seat-mounted side airbag when the passenger seat is empty to prevent unnecessary replacement of airbag(s) after a collision.
If any of these things happen, even intermittently , have the Personal Safety System™ serviced at an authorized dealer immediately . Unless serviced, the system may not function properly in the event of a collision. Safety belt precautions W ARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
W ARNING: When possible, all children 12 years old and under should be properly restrained in a rear seating position. W ARNING: Front and rear seat occupants, including pregnant women, should wear safety belts for optimum protection in an accident. Combination lap and shoulder belts 1.
• The energy management feature has a retractor assembly that is designed to extend the safety belt webbing in a controlled manner . This helps reduce the belt force acting on the user’ s chest.
How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Safety belt height adjustment Y our vehicle has safety belt height adjustments for the front outboard seating positions. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o adjust the shoulder belt height, squeeze the button and slide the height adjuster up or down.
W ARNING: Do not use extensions to change the fit of the shoulder belt across the torso. Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts.
If... Then... The driver’ s and front passenger’ s safety belts are buckled before the ignition is switched on or less than 1-2 minutes have elapsed since the ignition has been switched on.
Reasons given... Consider ... “Belts are uncomfortable” W e design our safety belts to enhance comfort. If you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible; this can improve comfort.
W ARNING: Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder 威 chime. T o do so may adversely affect the performance of the vehicle’ s air bag system.
1. Switch the ignition on. DO NOT ST ART THE ENGINE. 2. W ait until the safety belt warning light turns off (Approximately one minute). • Step 3 must be completed within 50 seconds after the safety belt warning light turns off.
Important supplemental restraint system precautions Airbags DO NOT inflate slowly or gently and the risk of injury from a deploying airbag is greatest close to the trim covering the airbag module.
W ARNING: Do not put anything on or over the airbag module. Placing objects on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury . W ARNING: Do not attempt to service, repair , or modify the airbag supplemental restraint system (SRS) or its fuses.
How does the airbag supplemental restraint system work? The airbag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates airbag inflation.
W ARNING: Several air bag system components get hot after inflation. Do not touch them after inflation. W ARNING: If the air bag has deployed, the air bag will not function again and must be replaced immediately . If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
The front passenger sensing system will disable (will not inflate) the front passenger’ s frontal airbag if: • the front passenger seat is unoccupied, or has small/medium objects in the front seat.
The front passenger sensing system is designed to enable (may inflate) the front passenger’ s frontal airbag anytime the system senses that a person of adult size is sitting properly in the front passenger seat.
W ARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the front passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor .
W ARNING: T o reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped).
W ARNING: Any alteration/modification to the front passenger seat may affect the performance of the front passenger sensing system. Determining if the system is operational The supplemental restraint system uses a warning indicator light in the instrument cluster or a back-up tone to indicate the condition of the system.
W ARNING: Do not attempt to service, repair , or modify the airbag SRS, its fuses or the seat cover on a seat containing an airbag. See your authorized dealer . W ARNING: All occupants of the vehicle should always wear their safety belts even when an airbag SRS is provided.
The airbag SRS is designed to activate when the vehicle sustains lateral deceleration sufficient to cause the sensors to close an electrical circuit that initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system.
W ARNING: Do not lean your head on the door . The Safety Canopy™ could injure you as it deploys from the headliner . W ARNING: Do not attempt to service, repair , or modify the Safety Canopy™ system, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing a Safety Canopy™.
How does the Safety Canopy™ system work? The design and development of the Safety Canopy™ system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag T echnical W orking Group.
The Safety Canopy™ is mounted to roof side-rail sheet metal, behind the headliner , along the entire side of the vehicle. In certain lateral collisions or rollover events, the Safety Canopy™ system will be activated, regardless of which seats are occupied.
Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Airbag readiness section in the Instrument Cluster chapter . Routine maintenance of the airbag is not required.
Important child restraint precautions W ARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight.
Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommended restraint type Small children Children who have outgrown or no longer properly fit in a child safety seat (generally children who are less than 4 feet 9 inches (1.
Recommendations for attaching child safety restraints for children Restraint T ype Child W eight Use any attachment method as indicated below by “X” LA TCH (lower anchors and top tether anchor) LA.
W ARNING: Always carefully follow the instructions and warnings provided by the manufacturer of any child restraint to determine if the restraint device is appropriate for your child’ s size, height, weight, or age.
training to ensure that all children ages 0 to 16 are properly restrained in the correct restraint system. Ford recommends checking with a NHTSA Certified Child Passenger Safety T echnician (CPST) and your pediatrician to make sure your seat is appropriate for your child and properly installed in the vehicle.
restrained properly in a rear seating position, properly restrain the largest child in the front seat. Installing child safety seats with combination lap and shoulder belts Check to make sure the child seat is properly secured before each use. Children 12 and under should be properly restrained in a rear seating position whenever possible.
2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out. 6. Allow the belt to retract to remove slack. The belt will click as it retracts to indicate it is in the automatic locking mode.
and forward and back. There should be no more than one inch (2.5 cm) of movement for proper installation. 11. Ford recommends checking with a NHTSA Certified Child Passenger Safety T echnician (CPST) to make certain the child restraint is properly installed.
The LA TCH anchors are located at the rear section of the rear seat between the cushion and seatback, below the locator symbols on the seat back. Follow the child seat manufacturer’ s instructions to properly install a child seat with LA TCH attachments.
If the safety seat is not anchored properly , the risk of a child being injured in a crash greatly increases. Combining safety belt and LA TCH lower anchors for attaching child safety seats When used in combination, either the safety belt or the LA TCH lower anchors may be attached first, provided a proper installation is achieved.
Perform the following steps to attach a child safety seat to the tether anchor: 1. Route the child safety seat tether strap over the back of the seat. For vehicles with adjustable head restraints, route the tether strap under the head restraint and between the head restraint posts, otherwise route the tether strap over the top of the seatback.
Child booster seats The belt-positioning booster (booster seat) is used to improve the fit of the vehicle safety belt. Children outgrow a typical child seat (e.g, convertible or toddler seat) when they weigh about 40 lb (18 kg) and are around four (4) years of age.
Booster seats should be used until you can answer YES to ALL of these questions when seated without a booster seat: • Can the child sit all the way back against the vehicle seat back with knees bent.
Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder .
Move a child to a different seating location if the shoulder belt does not stay positioned on the shoulder during use. Follow all instructions provided by the manufacturer of the booster seat.
INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING T ire Quality Grades apply to new pneumatic passenger car tires. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
W ARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics.
• Extra load: A class of P-metric or Metric tires designed to carry a heavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires]. Increasing the inflation pressure beyond this pressure will not increase the tire’ s load carrying capability .
W ARNING: Under -inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury . Under -inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire.
Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressure when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive.
Tire wear When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding and hydroplaning. Built-in treadwear indicators, or “wear bars”, which look like narrow strips of smooth rubber across the tread will appear on the tire when the tread is worn down to 1/16th of an inch (2 mm).
This begins with the letters “DOT” and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built.
W ARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below . If the beads do not seat at the maximum pressure indicated, re-lubricate and try again.
W ARNING: If your vehicle is stuck in snow , mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. W ARNING: Do not spin the wheels at over 35 mph (56 km/h).
• Front Wheel Drive (FWD) vehicles (front tires at top of diagram) 2009 MKS (mks) Owners Guide (post-2002-fmt) USA (fus) Tires, Wheels and Loading 185.
• Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/All Wheel Drive (A WD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires.
Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.
Note: Y ou may not find this information on all tires because it is not required by federal law . Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R .
12. T readwear , T raction and T emperature Grades • T readwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below . Note: T ire Quality Grades do not apply to this type of tire.
Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label.
following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. W ARNING: The T ire Pressure Monitoring System is NOT a substitute for manually checking tire pressure.
When your temporary spare tire is installed When one of your road tires needs to be replaced with the temporary spare, the TPMS system will continue to identify an issue to remind you that the damaged road wheel/tire needs to be repaired and put back on your vehicle.
Low T ire Pressure W arning Light Possible cause Customer Action Required Solid W arning Light T ire(s) under -inflated 1. Check your tire pressure to ensure tires are properly inflated; refer to Inflating your tires in this chapter .
Low T ire Pressure W arning Light Possible cause Customer Action Required Flashing W arning Light Spare tire in use Y our temporary spare tire is in use.
any tire is under -inflated, carefully drive the vehicle to the nearest location where air can be added to the tires. Inflate all the tires to the recommended inflation pressure. SNOW TIRES AND CHAINS W ARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford.
• The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from your vehicle when using snow tires and chains.
Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label on the B-Pillar or the edge of the driver’ s door (vehicles exported outside the US and Canada may not have a T ire Label).
Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload.
GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door .
W ARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury .
W ARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury . Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.
to transport the cement to your home? If you and your friend each weigh 220 lb. (99 kg), the calculation would be: 1,400 - (2 x 220) - (12 x 100) = 1,400 - 440 - 1,200 = - 240 lb.
Hitches Do not use hitches that clamp onto the vehicle bumper . Use a load carrying hitch. Y ou must distribute the load in your trailer so that 10–15% of the total weight of the trailer is on the tongue. Safety chains Always connect the trailer’ s safety chains to the frame or hook retainers of the vehicle hitch.
Driving while you tow When towing a trailer: • T urn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer . • It is recommended to select the “M” gear position when additional engine braking is needed.
RECREATIONAL T OWING Follow these guidelines for your specific powertrain combination to tow your vehicle for personal travel (such as behind a motor home or a truck). In case of roadside emergency with a disabled vehicle, please refer to Wrecker towing in the Roadside Emergencies chapter .
STARTING Positions of the ignition 1. Off— locks the gearshift lever and allows key removal. This position also shuts the engine and all electrical accessories off. 2. Accessory— allows the electrical accessories such as the radio to operate while the engine is not running.
W ARNING: Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine.
• Make sure the gearshift lever is in P (Park). 3. T urn the key to 3 (on) without turning the key to 4 (start). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights.
3. After idling for a few seconds, apply the brake, shift into gear and drive. Note: If the engine does not start on the first try , turn the key to the off position, wait 10 seconds and try step 2 again.
Note: When the vehicle is in motion, a single press and release of the start/stop button will not switch off the engine. In order to switch off the engine of a vehicle while in motion, press and hold the start/stop button for at least one second.
Fast Restart Feature: The Fast Restart feature allows you to re-start your vehicle within 20 seconds of switching the vehicle off, if a valid Intelligent Access Key is not present.
ENGINE BLOCK HEATER (IF EQUIPPED) An engine block heater warms the engine coolant which aids in starting and allows the heater/defroster system to respond quickly .
• Be sure that areas where the vehicle is parked are clean and clear of all combustibles such as petroleum products, dust, rags, paper and similar items. • Be sure that the engine block heater , heater cord and extension cord are solidly connected.
brake pedal pulsation may be observed during ABS braking and the brake pedal may suddenly travel a little farther as soon as ABS braking is done and normal brake operation resumes. These are normal characteristics of the ABS and should be no reason for concern.
Parking brake Apply the parking brake whenever the vehicle is parked. T o set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned on) until the parking brake is released.
ADVANCET RAC 姞 STABILITY ENHANCEMENT SYSTEM W ARNING: V ehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction and/or wheel/tire size may change the handling characteristics of the vehicle and may adversely affect the performance of the AdvanceT rac 威 system.
The AdvanceT rac 威 system provides the following stability enhancement features for certain driving situations: • T raction Control (TCS), which functions to help avoid drive-wheel spin and loss of traction.
T raction Control (TCS) T raction Control is a driver aid feature that helps your vehicle maintain traction of the wheels, typically when driving on slippery and/or hilly road surfaces, by detecting and controlling wheel spin.
• Entering a snow-free road from a snow-covered side street, or vice versa • Entering a paved road from a gravel road, or vice versa • Cornering while towing a heavily loaded trailer (refer to T railer towing in the T ires, Wheels and Loading chapter).
It is also important to maintain a proper power steering fluid level in the power steering fluid reservoir: • Do not operate the vehicle with a low power steering pump fluid level. See Power steering fluid in the Maintenance and Specifications chapter .
W ARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Switch the ignition to off, and remove the key whenever you leave your vehicle. W ARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly .
W ARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Switch the ignition off and remove the key whenever you leave your vehicle. R (Reverse) W ith the gearshift lever in R (Reverse), the vehicle will move backward.
• The overdrive cancel and grade assist lamp in the instrument cluster is illuminated. 2. Grade Assist • Improves driving experience in hilly terrain or mountainous areas by providing additional grade (engine) braking and extends lower gear operation on uphill climbs.
Understanding your SelectShift™ Automatic T ransmission gearshift lever (SST) This vehicle is equipped with a SelectShift™ Automatic T ransmission (SST) gearshift lever . SST is an automatic transmission with the ability for the driver to change gears up or down (without a clutch) as desired.
In order to prevent the engine from running at too low an RPM, which may cause it to stall, the SST will still automatically make some downshifts if it has determined that you have not downshifted in time.
The reverse sensing portion of the system detects obstacles up to 6 ft. (2 m) from the rear bumper with a decreased coverage area at the outer corners of the bumper , (refer to the illustration for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases.
W ARNING: This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle. The system may not detect smaller objects, particularly those close to the ground.
The system defaults to enabled every time the ignition is switched on. Press the control to disable or enable the system Keep the sensors (located on the front and rear bumper/fascia) free from snow , ice and large accumulations of dirt (do not clean the sensors with sharp objects).
After shifting out of R (Reverse) and into any gear other than P (Park), the image will remain until the vehicle speed reaches five mph (8 km/h), only if the rear camera delay feature is on, or until any navigation radio button is depressed. Note: The default setting for the rear camera delay is off.
dark. If either of the lamps are not operating, stop using the reverse camera system, at least in the dark, until the lamp(s) are replaced and functioning. Servicing • If the image comes on while the vehicle is not in R (Reverse), have the system inspected by your authorized dealer .
Driving on slippery surfaces with A WD vehicles A WD vehicles are specially equipped for driving on sand, snow , mud and rough roads and have operating characteristics that are somewhat different from conventional vehicles, both on and off the highway .
Do not rock the vehicle for more than a few minutes or damage to the transmission and tires may occur or the engine may overheat. W ARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Switch the ignition off and remove the key whenever you leave your vehicle.
gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels. When driving at slow speeds in deep sand under high outside temperatures, use a low gear when possible. Lower gear operation will maximize the engine and transmission cooling capability .
“T read Lightly” is an educational program designed to increase public awareness of land-use regulations and responsibilities in our nations wilderness areas.
Driving on snow and ice Note: Excessive tire slippage can cause transmission damage. A WD vehicles have advantages over 2WD vehicles in snow and ice but can skid like any other vehicle. Should you start to slide while driving on snowy or icy roads, turn the steering wheel in the direction of the slide until you regain control.
DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks).
ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program.
• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits In Canada, for uninterrupted Roadside Assistance coverage, you may purchase extended coverage prior to your Basic W arranty’ s Roadside Assistance expiring.
Note: W ith extended use, the flasher may run down your battery . FUEL PUMP SHUT-OFF In the event of a moderate to severe collision, this vehicle is equipped with a fuel pump shut-off feature that stops the flow of fuel to the engine. Not every impact will cause a shut-off.
Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.
Passenger compartment fuse panel The fuse panel is located under the instrument panel to the left of the steering wheel. The fuses are coded as follows.
Fuse/Relay Location Fuse Amp Rating Protected Components 9 15A Courtesy lamps 10 15A Illumination switch, Puddle lamps 11 10A All Wheel Drive (A WD) 12 7.
Fuse/Relay Location Fuse Amp Rating Protected Components 37 10A Not used (spare) 38 20A Amplifier (THX or 6 channel) 39 20A Radio/Navigation 40 20A Amplifier (THX or 2 channel) 41 15A Delayed Accessory 42 10A Not used (spare) 43 10A Heated backlite relay 44 10A Not used (spare) 45 5A W iper relay and module, Blower relay 46 7.
The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Protected Components 1 80A* SPDJB power 2 80A* SPDJB power 3 — Not used 4 30A Front wipers 5 30A Passenger power seat.
Fuse/Relay Location Fuse Amp Rating Protected Components 16 20A** Left HID 17 10A** Alternator sense 18 — Not used 19 20A IP power point 20 40A* HTD Backlite 21 20A* Console power point 22 30A* Front heated/cooled seats 23 7.
Fuse/Relay Location Fuse Amp Rating Protected Components 46 15A** VPWR2, VPWR3 47 15A** PCM VPWR1 48 15A** VPWR4 Ignition coils 49 10A** Heated mirrors 50 Full ISO relay PCM relay 51 Full ISO relay Bl.
W ARNING: Refer to T ire Pressure Monitoring System (TPMS) in the T ires, Wheels and Loading chapter for important information. If the tire pressure monitor sensor becomes damaged, it will no longer function.
Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • W inter weather driving capability • W et weather driving capability 3.
Stopping and securing the vehicle 1. Park on a level surface, set the parking brake and activate hazard flashers. 2. Place gearshift lever in P (Park) and switch engine off. Removing the spare tire and jack 1. Lift the trunk cargo cover , and remove the wing nut that secures the spare tire by turning it counterclockwise.
W ARNING: T o help prevent the vehicle from moving when you change a tire, be sure to place the transmission in P (Park), set the parking brake and block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.
3. Align the slot on top of the jack with the sheet metal flange indicated by the jack locator triangle next to the tire you are changing. T urn the jack handle clockwise until the wheel is completely off the ground. Note: DO NOT LIFT ON THE PLASTIC MOLDING, as this could damage molding.
Stowing the tire and jack 1. Fully collapse the jack, fold the lug wrench socket into the handle and place the jack and wrench into the felt bag as shown.
If you are stowing the flat tire: 1. Remove the extension bolt from the exterior pocket of the felt bag. 2. Install the jack as shown in Step 4 under Stowing the tire and jack . 3. Screw the extension bolt onto the threaded stud of the jack retention bracket.
Note: Inspect the wheel pilot hole prior to installation. If there is visible corrosion in wheel pilot hole, remove loose particles by wiping with clean rag and apply grease. Apply grease only to the wheel pilot hole surface by smearing a “dime” (1 square cm) sized glob of grease around the wheel pilot surface (1) with end of finger .
Preparing your vehicle When the battery is disconnected or a new battery is installed, the automatic transmission must relearn its shift strategy . As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission.
2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery .
4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points.
Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery .
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery .
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment.
If the vehicle is towed by other means or incorrectly , vehicle damage may occur . Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle.
GETTING THE SERVICES YOU NEED W arranty repairs to your vehicle must be performed by an authorized Ford, Lincoln, or Mercury dealer . While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction.
• Ford Genuine Accessories • Service specials and promotions. In Canada: Mailing Address (Ford vehicles) Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 T elephone 1-800-565-3673 (FORD) Online www .
In some states, you must directly notify Ford in writing before pursuing remedies under your state’ s warranty laws. Ford is also allowed a final repair attempt in some states.
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Y our satisfaction is important to Ford Motor Company and to your dealer . If a warranty concern has not been resolved using the three-step procedure outlined on the first page of the Customer Assistance section, you may be eligible to participate in the BBB AUTO LINE program.
authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory , Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor V ehicle Arbitration Plan (CAMV AP).
GETTING ASSIST ANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country , contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel.
Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www .helminc.com. (Items in this catalog may be purchased by credit card, check or money order .
REPORTING SAFETY DEFECTS (CANADA ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform T ransport Canada, using their toll-free number: 1–800–333–0510.
W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3-A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid.
W AXING • W ash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Premium Liquid W ax (ZC-53-A), which is available from your authorized dealer , or an equivalent quality product.
ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • T ake care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage.
WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly . If the wipers do not wipe properly , substances on the vehicle’ s glass or the wiper blades may be the cause.
• Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the interior painted surfaces. • Do not use household or glass cleaners as these may damage the finish of the instrument panel, interior trim and cluster lens.
W ARNING: Do not use cleaning solvents, bleach or dye on the vehicle’ s safety belts, as these actions may weaken the belt webbing. W ARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents.
FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Y our Ford or Lincoln Mercury authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
SERVICE RECOMMENDATIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service.
OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located at the bottom of the instrument panel near the steering column. 2. Go to the front of the vehicle and release the auxiliary latch using the handle that is located under the front passenger side of the hood.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Brake fluid reservoir 4. Battery 5. Power distribution box 6. Air filter assembly 7. Automatic transmission fluid dipstick 8. Engine oil dipstick 9.
WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16-A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash.
CHANGING THE WIPER BLADES 1. Pull the wiper blade and arm away from the glass. T urn the blade at a right angle to the arm. 2. Squeeze the locking tabs to release the blade from the arm and pull the blade away from the arm to remove it. 3. Attach the new blade to the arm and snap it into place.
5. Locate and carefully remove the engine oil level dipstick. 6. W ipe the dipstick clean. Insert the dipstick fully , then remove it again. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the level within the normal operating range.
• Do not overfill the engine with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by an authorized dealer . 7. Put the dipstick back in and ensure it is fully seated. Adding engine oil 1.
Use SAE 5W -20 engine oil Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.
If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. Y ou can neutralize the acid with a solution of baking soda and water . It is recommended that the negative battery cable terminal be disconnected from the battery if you plan to store your vehicle for an extended period of time.
Because your vehicle’ s engine is electronically controlled by a computer , some control conditions are maintained by power from the battery . When the battery is disconnected or a new battery is installed, the engine must relearn its idle and fuel trim strategy for optimum driveability and performance.
concentration should be maintained at 50/50 coolant and distilled water , which equates to a freeze point of -34°F (-36°C). Coolant concentration testing is possible with a hydrometer or antifreeze tester (such as the Rotunda Battery and Antifreeze T ester , 014–R1060).
Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolant and distilled water . Add the mixture to the coolant reservoir , when the engine is cool, until the appropriate fill level is obtained. W ARNING: Do not add engine coolant when the engine is hot.
For vehicles with overflow coolant systems with a non-pressurized cap on the coolant recovery system, add coolant to the coolant recovery reservoir when the engine is cool.
Y our cooling system may have a leak. Operating an engine with a low level of coolant can result in engine overheating and possible engine damage. Recycled engine coolant Ford Motor Company does NOT r.
• Decreased engine coolant concentrations below 40% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage. • Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive.
When fail-safe mode is activated Y ou have limited engine power when in the fail-safe mode, so drive the vehicle with caution. The vehicle will not be able to maintain high-speed operation and the engine will run rough. Remember that the engine is capable of completely shutting down automatically to prevent engine damage, therefore: 1.
W ARNING: Gasoline may contain benzene, which is a cancer -causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling.
W ARNING: The flow of fuel through a fuel pump nozzle can produce static electricity , which can cause a fire if fuel is pumped into an ungrounded fuel container . Refueling W ARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries.
4. After you are done pumping fuel, slowly remove the fuel filler nozzle—allow about five seconds after pumping fuel before removing the fuel filler nozzle. This allows residual fuel to drain back into the fuel tank and not spill onto the vehicle. If the Check Fuel Fill Inlet message comes on, the fuel fill inlet may not have properly closed.
Octane recommendations Y our vehicle will run normally on 87 octane regular fuel. Premium fuel will provide improved performance. W e do not recommend the use of gasolines labeled as “Regular” in high altitude areas that are sold with octane ratings less than 87.
• Normally , adding 1 gallon (3.8L) of fuel is enough to restart the engine. If the vehicle is out of fuel and on a steep grade, more than 1 gallon (3.
2. Slowly insert the funnel into the Easy Fuel™ system. 3. Fill the vehicle with fuel from the portable fuel container . 4. When done, clean the funnel or properly dispose of it. Extra funnels can be purchased from your authorized dealer if you choose to dispose of the funnel.
The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range. When refueling your vehicle after the fuel gauge indicates empty , you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank.
Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy . Habits • Smooth, moderate operation can yield up to 10% savings in fuel.
Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. • Carrying unnecessary weight may reduce fuel economy (approximately 1 mpg [0.
The scheduled maintenance items listed in scheduled maintenance information are essential to the life and performance of your vehicle and to its emissions system.
a malfunction. T emporary malfunctions may cause the Service engine soon indicator to illuminate. Examples are: 1. The vehicle has run out of fuel—the engine may misfire or run poorly . 2. Poor fuel quality or water in the fuel—the engine may misfire or run poorly .
for 15 seconds without cranking the engine. If the Service engine soon indicator blinks eight times, it means that the vehicle is not ready for I/M testing; if the Service engine soon indicator stays on solid, it means that the vehicle is ready for I/M testing.
BRAKE FLUID The fluid level will drop slowly as the brakes wear , and will rise when the brake components are replaced. Fluid levels between the “MIN” and “MAX” lines are within the normal operating range; there is no need to add fluid.
7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated areas for normal operating temperature. Low fluid level Do not drive the vehicle if the fluid level is in the add range or does not show at all on the dipstick.
If an overfill occurs, excess fluid should be removed by an authorized dealer . An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Do not use supplemental transmission fluid additives, treatments or cleaning agents.
6. Replace the air filter housing cover and secure the clamps. Be sure that the air cleaner cover tabs are engaged into the slots of the air cleaner housing.
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Items Capacity Ford Part Name or equivalent Ford Part Number / Ford Specification Brake fluid Between MAX and MIN on reservoir Motorcraft High Perform.
Items Capacity Ford Part Name or equivalent Ford Part Number / Ford Specification Engine coolant 11.1 quarts (10.5L) Motorcraft Premium Gold Engine Coolant with bittering agent (yellow-colored) 4 VC-7.
ENGINE DATA Engine 3.7L-DOHC V6 engine Displacement 3.7L Fuel 87 octane (normal operation) or 91 octane (maximum performance) Firing order 1–4–2–5–3–6 Spark plug gap 0.052–0.056 inch (1.32–1.42 mm) Ignition system Coil on plug Compression ratio 10.
IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake system / Gross V ehicle W eight Rating (GVWR) / Restraint System 3. V ehicle line, series, body type 4. Engine type 5. Check digit 6.
GENUINE LINCOLN ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Lincoln Accessories are available for your vehicle through your local Lincoln or Ford of Canada dealer .
Peace of mind Remote start V ehicle security systems Wheel locks For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When .
A Accessory delay .......................... 58 Adaptive Cruise Control ............. 63 AdvanceT rac .............................. 218 Air cleaner filter ............... 309–310 Air conditioning ....................32, 35 Airbag supplemental restraint system .
recommendations ................... 162 Child safety seats - booster seats ........................................... 172 Cleaning your vehicle engine compartment ..............274 instrument panel .................... 275 interior ..................
refill capacities ........................ 311 service points .................. 281–282 Engine block heater ................. 214 Engine oil .................................. 283 change oil soon warning, message center ....................... 283 checking and adding .
Instrument panel cleaning ................................... 275 cluster ........................................ 10 lighting up panel and interior ....................................... 46 Intelligent Access Key ................ 93 Intelligent Access with push button start .
Passenger Occupant Classification Sensor ................. 133 Power distribution box (see Fuses) ............................... 245 Power door locks ........................ 94 Power mirrors ............................. 59 Power point .............
Starting your vehicle ........ 208–210 jump starting .......................... 256 push button start system .......211 Steering wheel controls ...................................... 72 tilting ......................................... 53 Stereo 6-CD in dash .
Ein wichtiger Punkt beim Kauf des Geräts Lincoln 2009 MKS (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Lincoln 2009 MKS noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Lincoln 2009 MKS - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Lincoln 2009 MKS reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Lincoln 2009 MKS erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Lincoln 2009 MKS besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Lincoln 2009 MKS verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Lincoln 2009 MKS. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Lincoln 2009 MKS gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
