Benutzeranleitung / Produktwartung 55LA86-Z des Produzenten LG Electronics
Zur Seite of 127
Printed in Korea P/NO : MFL67733205 (1304-REV01) CHASSIS : LD34D MODEL: 55LA86** 55LA86**-Z* CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. LED TV SER VICE MANUAL North/Latin America http://aic.lgservice.com Europe/Africa http://eic.
- 2 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes CONTENTS CONTENTS .............................................................................................. 2 SAFETY PRECAUTIONS .
- 3 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Exploded View .
- 4 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes SER VICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the SAFETY PRECAUTIONS on page 3 of this publication.
- 5 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent at against the cir- cuit foil.
- 6 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes SPECIFICA TION NOTE : Specifications and others are subject to change without notice for improvement . 1. Application range This specification is applied to the LED TV used LD34D chassis.
- 7 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes No. Item Specication Remarks 2 Broadcasting system 1) P AL-BG/DK/I/I’ 2) .
- 8 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes 5. External input format 5.1. 2D Mode (1) Component input(Y , CB/PB, CR/PR) (2) HDMI Input (PC/DTV) No. Resolution H-freq(kHz) V -freq(Hz) 1.
- 9 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes 5.2 . 3D Mode (1) RF Input(3D supported mode manually) No. Resolution Proposed 3D input proposed mode 1 HD - DTV 1080I 720P 2D to 3D Side by Side(Half) T op & Bottom 2 SD - DTV 576P 576I 3 SD - A TV(CVBS/SCART) (3) HDMI 1.
- 10 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes (4) HDMI 1.4b (3D supported mode automatically) No. Resolution H-freq(kHz) V -freq.(Hz) Pixel clock(MHz) VIC 3D input proposed mode Proposed 1 640*480 31.
- 1 1 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes No. Resolution H-freq(kHz) V -freq.(Hz) Pixel clock(MHz) 3D input proposed mode Proposed 1 1024*768 48.36 60 65 2D to 3D, Side by Side(half) T op & Bottom HDTV 768P 2 1360*768 47.
- 12 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes No. Resolution H-freq(kHz) V -freq.
- 13 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes ADJUSTMENT INSTRUCTION 1. Application Range This specification sheet is applied to all of the LED TV with LD34D chassis.
- 14 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes 3.3. LAN Inspection 3.3.1. Equipment & Condition ▪ Each other connection to LAN Port of IP Hub and Jig 3.
- 15 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes 3.6. Model name & Serial number Download 3.6.1. Model name & Serial number D/L ▪ Press "Power on" key of service remote control.
- 16 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes 4. Manual Adjustment * ADC adjustment is not needed because of OTP(Auto ADC adjustment) 4.1. ED I D ( T h e E x t e n de d D i s p l a y I d e nt i f i c a t i o n Data)/DDC(Display Data Channel) download 4.
- 17 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes # HDMI 3(C/S : E8 61) EDID Block 0, Bytes 0-127 [00H-7FH] EDID Block 1, Bytes 128-255 [80H-FFH] # HDMI 4(C/S : E8 51) EDID Block 0, Bytes 0-127 [00H-7FH] EDID Block 1, Bytes 128-255 [80H-FFH] 4.
- 18 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes ▪ Adj. Map 4.2.5. Adj. method (1) Auto adj. method 1) Set TV in adj. mode using POWER ON key . 2) Zero calibrate probe then place it on the center of the Display .
- 19 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes ▪ Standard color coordinate and temperature using CA-210(CH 18) 4.2.7. EDGE LED White balance table (1) EDGE LED module change color coordinate because of aging time.
- 20 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes 4.6. Wi-Fi T est Step 1) T urn on TV Step 2) Select Network Connection option in Network Menu. Step 3) Select Start Connection button in Network Connection.
- 21 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes 4.1 1. HDMI ARC Function Inspection (1) T est equipment - Optic Receiver Speaker - MSHG-600 (SW: 1220 ↑) - HDMI Cable (for 1.
- 22 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes 6. USB S/W Download(Service only) (1) Put the USB Stick to the USB socket. (2) Automatically detecting update file in USB Stick.
- 23 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes A22 A10 A T1 AG1 900 200 310 CAM1 400 420 410 540 530 120 570 560 300 510 121.
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THERMAL THERMAL THERMAL THERMAL THERMAL THERMAL THERMAL THERMAL THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THERMAL THERMAL THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
Fiber Optic THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THERMAL THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
USB DOWN STREAM USB DOWN STREAM THERMAL THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THERMAL THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THERMAL THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THERMAL THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THERMAL THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THERMAL THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THERMAL THERMAL THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
.
2013 LED/LCD TV Engineering guide < A pplicable Model : High -end Platform >.
EPI In terface EPI(Embedd ed Point-Poin t Interface) Features • Point-Point topology (support 2 Pair o ption) • CDR (C lock Data Recovery ) • Bandwidth up to 1.
EPI In terface (mini-L VDS v s. EPI) Comparison HF mini-L VDS What to change EPI (Emb edded clock P- to -P Interface) -Difficult to upgrade band width limit -M ultiple number of wires needed for higher band width HF mini- LVDS FHD (10bit) 60Hz 120Hz 240Hz No.
HF mini-L VDS EPI T opology Protocol Features @10bit, FHD120 • Multi Drop • Data rate: 660 Mbps • External clock • Point to Point • Data rate : 1.
NFC (Near field communi cation) Near field communic ation (NFC) is a set of standards for smartphones and similar devices to establish radio communication w ith each other by touching them together or bringing them into clos e proximity , usually no more than a few centimetres.
Main PCB for Broadband Main + TC ON all in one T o PSU 2 6 4 1 M ain process or, DDR M emory eMM C Memory 2 3 4 Micom for Key/IR/Logo sensing PMIC A udio A M P xxLA 790V - Zx Key +IR+L ogo Front Spk T.
Main PCB for Broadband Main + TC ON all in one T o PSU 1 M ain process or, DDR M emory eMM C Memory 2 3 4 Micom for Key/IR/Logo sensing PMIC A udio A M P xxLA 860V - Zx Key +IR+L ogo Front Spk T o module 5 EPI Wafer Chassis : LD 34D PCB P/N o : EA X65040 103 6 Level shifter WIFI/BT 2 6 4 5 3 1 T o Camera 7 USB 3.
Main PCB for Broadband Main + TC ON all in one T o PSU 1 M ain process or, DDR M emory eMM C Memory 2 3 4 Micom for Key/IR/Logo sensing USB 3.0 A udio A M P xxLA 960V - Zx Key +IR+L ogo Front Spk T o .
16 DDR3 16 1. H13 Block Diagram (External) DAC_DA T A HSR_P/M AA D_DATA CVBS BB_TP_DATA AUD Tuner PC_AUDI O PC_Au dio_L /R AV1_A udio L/R AV1 COMP1 AV1_CVBS Comp1 Y,P b,Pr HDMI Switch HDMI2 HDMI3 H13 LG1154A N USB1(USB3.
IC3201 SII9587CNUC HDMI_SW IC7700 TPS65178RSLR EPI AR15 [SCL0/GPIO66] AP15 [SDA0/GPIO65] I2C_SDA1 IC5600 TAS5733 AMP MAIN 24 [SCL] 23 [SDA] IC5700 TAS5733 AMP WOOFER 33 Ω 33 Ω IC3000 R5F100GEAF B RENESAS MICOM 3.3k Ω I2C_SCL1 3.3k Ω +3.3V_NOR +3.3V_NOR 3.
1.0V Core 3A 1.8V_TU 5V Normal 5A 1.5V DDR 3A IR A ss ’ y MICOM Ethernet PHY Wi - Fi A ss’y Logo Light A ss’y H13-D (VDDC) DDR (VDDQ) DDR (VDD) 3.5V 12V 24V H13-A (VDDC10) H13-A (A VDD10) H13-A (XTA L) 1.2V Core 8A H13-D (VDDC11) H13-D (A VDD11) H13-D (XTA L) 3.
4. T uner/CI Block Diagram LG1 154 TDSQ- G651D [RESET] 2 AG6[GPIO10] AH34 [SCL5] AH33 [SDA5] [SLC] 3 [SDA] 4 [+3.3V_TUNER] 5 [+.1.8V_TUNER] 7 [CVBS] 8 [ERROR] 16 [SYNC] 17 [VALID] 18 [MCLK] 19 AL37[TP_DVB_ERR] AL36 [TP_DVB_SOP] AL35 [TP_DVB_VAL] AM36 [TP_DVB_CLK] [D0-7] 20- 27 [+1.
COMP1_PR_IN_SOC COMP1_Y_IN_SOC COMP1_PB_IN_SOC COMP1_Y_IN_SOC_SOY 5. V ideo & Audio IN H13 (LG1 154AN) [CVBS_IN3] AV1_CVBS_IN AV1 Phone JACK [AUAD_L /R_CH3_IN] COMP1_Y/Pb/Pr Component 1 Phone JACK.
6. AUDIO OUT SPDIF_OUT TAS5733 AZ4580MTR OP A MP Mute CTRL [TR] LPF COMP1/AV1/DVI_L_IN [IEC958OUT] Tuner [AAD_A DC_SIF] SCART_MUTE SCART AUDIO L/R OUT I2C_SCL1/SDA1 MICOM MICOM [AUD_SCART_ OUTL/OUTR] .
HDMI Switch (IC3201 / SII9587CNUC) HDMI1 HDMI_HPD_ 1 ~ 4 5V_HD MI_1 ~ 4 HDMI Ou t put 8bits I2C_SCL/SDA 5 2bits CEC_REMOTE MHL OCP (IC3202 / TPS2554) MHL_D ET SPDIF_OUT_ARC HDMI_INT HDMI_S/W_RESET HDM.
(EPI CH1 ± ) (EPI CH3 ± ) TX0P/N TX2P/N (EPI CH2 ± ) TX1P/N EPI 50P_LEFT (LVDS_51PIN Side) (EPI CH4 ± ) (EPI CH6 ± ) TX3P/N TX5P/N (EPI CH5 ± ) TX4P/N 32/31 GMA_4/5/7/12/14/15 GMA_1/3/4/5/7/9/10.
PMIC TPS65178 Boost Converter Buck 1 converter(VCC) Buck 2 converter(Vcore) Buck 3 converter(HVdd) Buck 4 converter(VCC18) Positive Charge P ump Cont roller Negative Charge Pump Controller 6-Ch Gamma .
10. USB / WIFI / M-REMOTE / UART LG1154D_H13D USB1(3.0) USB3_DP USB3_DM [USB3_DP0] [USB3_RX0M] [USB3_RX0P] [USB3_TX0M] [USB3_TX0P] [USB3_DM0] USB2 USB_DP2 USB_DM2 [HUB_PORT_OVER0] [HUB_VBUS_CTRL0] O C.
Interconnection - 1 1 Main PCB 2 Power Board 3 Local key A ssy 1 2 3 4 5 Main / LPB 24Pin + Local Dimming Cable Main / Module EPI Cable 50& 50Pin LED driv er / PSU IR 8Pin Cable WiFi 6Pin + RF 8Pi.
8 7 Interconnection - 2 IR to Local Key 3Pin Cable IR to Logo A ssy 4Pin Cable [Cables] 7 8 [PCBs] 6 IR Assy 6 47LA 790V - ZA.
Interconnection - 1 1 Main PCB 2 Power Board 3 Local key A ssy 1 2 3 4 5 Main / LPB 24Pin + Local Dimming Cable Main / Module EPI Cable 50& 50Pin LED driv er / PSU WiFi 6Pin + RF 8Pin Cable SPK Ca.
8 7 Interconnection - 2 IR to Local Key 3Pin Cable IR cable [Cables] 7 8 [PCBs] 7 IR Assy 7 55LA 860V - ZA.
Interconnection - 1 1 2 3 1 2 3 4 5 60LA 860V - ZA 4 5 6 6 1 Main PCB 2 Power Board 3 Local key A ssy 1 2 3 4 5 Main / PSU 18Pin Main / T -con L VDS Cable 41& 51Pin LED driv er 14 Pin cable WiFi 6.
9 8 Interconnection - 2 IR to Local Key 3Pin Cable IR 8 Pin Cable [Cables] 8 8 [PCBs] 6 IR Assy 7 60LA 860V - ZA 7 LED Driv er 8 T -con 6 8.
Interconnection - 1 1 2 3 1 2 3 4 5 6 47LA 960V - ZA 4 5 1 Main PCB 2 Power Board 3 Local key A ssy 1 2 3 4 5 Main / PSU 18Pin Main / T -con L VDS Cable 41& 51Pin LED driv er 14 Pin Cable WiFi 6Pi.
Interconnection - 2 8 9 6 47LA 960V - ZA 9 8 IR 5 Pin + Loca l Key 3 Pin Cable Woofer Cable [Cables] [PCBs] 6 IR Assy 7 LED Driv er 8 T -con 7 8.
Introductions of 13Y RF ass’y + Magic Remote control 1. Syste m 2. Remote Buttons 3. MR13 Block Diagram 4. Function List 5. Pairing/Un-pairing Method.
1. System Remote RF Receiver TV UA RT or U SB RF Pairing Information T ransmission (Sen d to TV after Paired) • Static Calibration Data (Bypass only) • Remote FW v er .
2. Remote Button s (M4 vs. MR13P) BUTT ON RF Unpaired IR_CODE RF Paired RF_CODE IR continuous repeat ETC. Phsical Buttons POW ER 0x 08 NONE Y IR on ly BACK 0x28 0x8028 Y SMART 0x7C 0x807C Y ← 0x07 0x8007 Y → 0x06 0x8006 Y ↑ 0x40 0x8040 Y ↓ 0x41 0x8041 Y OK 0x75 0x8044 Y VOICE 0xDE 0x808B Y = VOICE_START 3D 0xDC 0x80DC Y Screen RMT / Q.
3. MR13P Block Diagram MPU-6150 (Gyr o+ACC) (Invensense) BCM20733M A2 (BROADCOM ) Bluetooth 3.0 Key Button ( 4 x 4 ) AA x 2 Battery DC -DC Boost TI TPS61097 SOT23-5 Power Management Antenna Partr on X-tal 24 MHz 2.8V LDO uP0108NEC5- 28 SC70 512Kb (Serial F/M) I2C ch1 I2C ch2 WM8950 (Wolfson) V oice MIC.
주요 Item IC Manufacturer Function Remocon V oice V oice Codec WM8950 Wolfson 16KHz Sampling of A ud io data MEMS Mic. SPU0414HR5H Know les Sensing V oice Motion Sensor Gy ro S ensor + A cceleromete.
5. RF Pairi ng / Un-pairing Method Method Description RF Pairing Method1 – If unpaired, just press "OK" button. – If paired, press "OK" button after unpairing. Method 2 (Repairing) – Press “BAC K" button for 5 sec.
1. Wi - Fi built in A ss’y feature 2. Wi - Fi built in A ss’y specification Introductions of 13Y WIFI buil t in ass’y.
WIFI Built in ass’y feature PIN USB i nterface 1 Vcc 2 DM 3 DP 4 GND 5 WOW 6 NC - Pin map BCM43236B Wafer 6pin 1.25mm 3.3V USB DP, DN GND USB DP, DN DCDC EUP3010 Cry stal 20MHz 3.
WIFI Built in ass’y Specification.
Contents of LCD TV Standard Repair Process No. Error symptom (High category) Error symptom (Mid category) Page Remarks 1 A. Video err or No video/Normal audio 1 2 No video/No audio 2 3 Video error, video lag/stop, fail tu nning 3, 4 4 Color err or 5 5 Vertical/Horizontal bar, residual image, light spot, externa l device color error 6 6 B.
Contents of LCD TV Standard Repair Process Detail T echnical Manual No. Error s ymp tom Conte nt Page Remar ks 1 A. Vi deo error_ No video/Normal audio Check LCD back li ght with n aked eye A1 2 LED driver B+ 24V measu ring method A2 3 Check White Balance value A3 4 Power Board voltage measuring me thod A4 6 A.
Normal audio Y N Move to No video/No audio No video Normal audio Check Back Light On w ith n aked eye On Y N Check Power Board 12v,3.5v etc. Normal voltage Y N Replace T-con Board or module And Adjust.
Normal voltage? Check v ariou s voltages of Pow er Board ( 3.5V,12V,20V or 24V…) No Video/ No audio Check and replace MAIN B/D Y Replace Pow er Board and repair parts N End Standard Repair Process A . Video error No video/ No audio ☞ A4 Established date Revised date LCD TV Error symptom 2012.
A . Picture Problem Picture broken/ Freezing Y N ☞ A6 N Check RF Signal level Normal Signal? Check RF Cable Connection 1. Reconnection 2. Install Booster Check S/W Version Use Signal Test Check Signal status S/W Upgrade Check whether other equipments have problem or not.
A . Picture Problem (DVB-S/S2) Tuning fail, Picture broken/ Freezing Y N ☞ A6 Check RF Signal level Normal Signal? Check S/W Version S/W Upgrade SVC Bulletin? Normal Picture? Y N Y Close Check RF signal cable (DVB satellite si gnal or not) C heck whe ther other equi pments ha ve problem or not.
Color error? Y N ※ Check and replace Link Cable (LVDS) and contact condition Y N Replace M ain B/D Color error? Check error color input mode Check color by input -External Input -COMPO NENT -RGB -HD.
Screen normal? N Y Check ex ternal device connecti on conditio n Y N Check and replace Link Cable Normal? Y N Screen normal? Repla ce Main B/D (adjust VCOM ) Replace module Check color condition by input -External Input -Component -RGB -HDMI/DVI End V ertical/Horizontal bar , residual image, l ight spot Request repair for ex ternal device A .
B. Po w er error No power Power LED On? Y N DC Power on by pressing Pow er Key On Remote control Y N Normal operation? Check Power On ‘”High” Check Pow er cord was inserted properly Check Power .
B. Power error Off when on, off while viewing, power auto on/off Error? N Y Check Power Off Mode Fix A/C cord & Outlet and check each 3 phase out Check A/C cord Check for all 3- phase power out Ch.
No audio Screen normal Check user menu > Speaker off Off N Y Cancel OFF Check audio B+ 24V of Power Board Norma l voltage Y N Replace Pow er Board and repair parts Check Speaker disconn ection N Y Replace Speaker Replace M AIN Board End C.
→ abnormal audio/discontinuation/noise is same after “Check input signal” compare d to No audio C. Au dio er ror Wrecked audio/ discontinuation/noise W recked audio/ Discontin uation/ Noise for .
D. Gen eral Fun ction Problem Remote control & Local sw itch checking Y N 1. Remote co ntrol(R/C) operatin g error Check R/C itself Operation Normal operating? Normal operating? Y Close Replace R/C If R/C operate, Explain the customer cause is interference from light in room.
Check technical inform ation - Fix information - S/W Version N Y Technical information? Check input signal Signal input? Y N External Input and Component Recognitio n error Check and fix external device/cable RGB,HDM I/ DVI, Optical Recognitio n error Replace Mai n B/D Replace Mai n B/D Fix in accordanc e with technical informatio n D.
Check locati on of noi se Identify noise ty pe Circuit noise Replace PS U(with LED driver) Replace LE D driver Mechanical noise Check location of noise OR ※ W hen the nose is severe, replace the mod.
Replace module Zoom p art with exterior damage Module damage Cabinet damage Replace cabinet Replace remote controller Remote controller damage Stand dent Replace stand F . Exterior defect Exterior defect A djust VCOM Established date Revised date LCD TV Error symptom Standard Repair Process ☞ A 28 2012.
G. Netw ork Error Exterior defect Established date Revised date LCD TV Error symptom Standard R epair Process 2012. 12 .06 Y N Check Network status Normal Signal? Check S/W Version S/W Upgrade SVC Bulletin? Normal Picture? Y N Y Close Check W ired ethernet cabl e connection Che ck whether AP has a probelm or not.
G. CI+ Competibility Error Exterior defect Established date Revised date LCD TV Error symptom Standard Repair Process 2012. 12 .06 Y N Check CI CA M statu s Read Information? Check CA M S/W Version CA M S/W Up grade By OTA SVC Bulletin? Normal Picture? Y N Y Close Check def ect CI slot pin Check it’s worked CI+ 1.
Contents of LCD TV Standard Repair Process Detail T echnical Manual N o. Error sympt om Conte nt Page R ema rks 21 B. Power error_No power Check front display LED A17 22 Check power in put Voltage & ST -BY 3.5V A18 23 Checking method when power is ON A 19 24 POWER BOARD voltage measuring method A5 25 26 B.
Standard Repair Process Detail T echnical Manual Check White Balance value A . Video error_No v ideo/Normal audio <ALL M ODELS> A4 Established date Revised date Error symptom Content LCD TV Entry me thod 1. Press the ADJ butto n on the remote controller for adjustm ent .
Standard Repair Process Detail T echnical Manual Power Board voltage measuring method A . Video error_No v ideo/ Au dio A5 Established date Revised date Error symptom Content LCD TV Check the DC 24V , 12V , 3.5V . 24 Pin (Power Board ↔ Main Board) SMAW200 - H24S 1 Power on 2 In verter On/o ff 3 3.
MENU support signal test select channel W hen the signal is strong, use the attenuator (-10dB, -15dB, -20dB etc.) Standard Repair Process Detail T echnical Manual TUNER input signal strength checking method A .
Standard Repair Process Detail T echnical Manual LCD-TV Version checking method A . Video error_Video error , video lag/s top 1. Checking method for remote controller for adjustment Press the IN-ST ART with the remote controller for adjustme nt V ersion <ALL M ODELS> A7 Established date Revised date Error symptom Content LCD TV 2012.
Standard Repair Process Detail T echnical Manual LCD TV connection diagram (1) A . Video error _V ertic al/Horizontal bar , residual image, light spot A s the part c onnecting to the e xternal input, check the screen condition by signa l A8 Established date Revised date Error symptom Content LCD TV <ALL M ODELS> 2012.
Checking method: 1. Check the signal strength or check w hether the screen is normal w hen the external dev ice is connected. 2. Aft er measuring each voltage from pow er supply, finally replace the MAIN BOARD. Standard Repair Process Detail T echnical Manual TUNER checking part A .
Standard Repair Process Detail T echnical Manual A djustment T est pattern - ADJ Key A . Video error_Color error Y ou can view 6 ty pes o f patterns using the ADJ Ke y Checking item : 1. Defective pixel 2. Residual image 3. M ODULE error (ADD-BAR,SCAN BAR.
Solder def ect, CNT Broken T -Con Defect, CNT Broken T -Con Defect, CNT Broken T -Con Defect, CNT Broken Solder def ect, CNT Broken Solder def ect, CNT Broken Solder def ect, CNT Broken Solder def ect.
Abnormal Power Section Solder def ect, Short/Crack Abnormal Power Section Solder def ect, Short/Crack Fuse Open, Abnorm al power section Noise GRADA TION GRADA TION Abnormal Display A ppendix : Exchan.
A ppendix : Exchange LPB(LED driv er) No Lig ht Dim Lig ht Dim Lig ht Dim Lig ht.
A ppendix : Exchange the Modul e (1) Panel Mura, Light leakage Press damage Crosstalk Crosstalk Press damage Panel Mura, Light leakage Press damage Un -repairable Case s In this ca se please exchange the module.
V ertical Block Source T AB IC Defect Horizontal Block Gate T AB IC Defect Gate T AB IC Defect Gate T AB IC Defect V ertical Line Source T AB IC Defect V ertical Block Source T AB IC Defect Horizontal.
Standard Repair Process Detail T echnical Manual Check front display LED B. Po w er error _No pow er A 17 Established date Revised date Error symptom Content LCD TV LOGO LED Front LOGO LED control in the status of ST -BY Condition: Menu Option LG Logo Ligh t Brightness(OF F ,LO W ,MIDDLE,HIGH) 2012.
24 Pin (Power Board ↔ Main Board) SMAW200 - H24S 1 Power on 2 In verter On/o ff 3 3.5V 4 PWM Dim #1 5 3.5V 6 PWM Dim #2 7 GND 8 GND 9 24V 10 24V 11 GND 12 GND 13 12V 14 12V 15 12V 16 24V 17 GND 18 G.
Standard Repair Process Detail T echnical Manual Checking method when power is ON B. Po w er error _No pow er A 19 Established date Revised date Error symptom Content LCD TV Check “power on” pin is high 2012. 12 .06 24 Pin (Power Board ↔ Main Board) SMAW200 - H24S 1 Power on 2 Inverter On/o ff 3 3.
Entry method 1. Press the IN-ST AR T button of the remote controller for adjustment 2. Check the entry into adjustment item 3 Standard Repair Process Detail T echnical Manual POWER OFF MODE checking method B. Power error _Off when on, off whiling v iew ing <ALL M ODELS> A 22 Established date Revised date Error symptom Content LCD TV 2012.
Checking meth od 1. Press the M ENU butto n on the remote controller 2. Select the SOUND f unction of the Menu 3. Change TV Sound Out to TV Speaker Standard Repair Process Detail T echnical Manual Checking method in menu when there is no audio C.
24 Pin (Powe r Boar d ↔ Main Bo ard) SMAW200 - H24S 1 Power on 2 I nverter On /off 3 3.5V 4 PWM Dim #1 5 3.5V 6 PWM Dim #2 7 GND 8 GND 9 24V 10 24V 11 GND 12 GND 13 12V 14 12V 15 12V 16 24V 17 GND 1.
Checking order 1, 2. Check IR cable condition betw een IR & Main board. 3. Check the st-by 3.5V on the terminal 4. 4. W hen checking the Pre-Amp when the pow er is in ON condition, it is normal when the Analog T ester needle moves slowly , a nd defective when it does not mov e at all.
Standard Repair Process Detail T echnical Manual Sequence of the Vcom adjustment D. VC OM A djustment 1. Case ■ LCD module change ■ T -Con board change 2.
Ein wichtiger Punkt beim Kauf des Geräts LG Electronics 55LA86-Z (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie LG Electronics 55LA86-Z noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für LG Electronics 55LA86-Z - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von LG Electronics 55LA86-Z reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über LG Electronics 55LA86-Z erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon LG Electronics 55LA86-Z besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von LG Electronics 55LA86-Z verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit LG Electronics 55LA86-Z. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei LG Electronics 55LA86-Z gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
