Benutzeranleitung / Produktwartung WS-7208U des Produzenten La Crosse Technology
Zur Seite of 22
WS-7208U Wireless 433 MHz Weather Station Instruction Manual .
2 TABLE OF CONTENTS Topic Page Quick Setup 3-5 Inventory of Contents 6-7 Detailed Setup Guide Battery Installation 8 Setting the Time 9 Features Minimum and Maximum Temperatures 10 Resetting Minimum a.
3 QUICK SETUP Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor tem perature station and remote tem perature sensor 3 to 5 feet apart. 2. Batteries shoul d be out of both units for 10 minutes. 3. Place the batteries into the remote temperature sensor first then into the indoor tem perature station.
4 display will show both the indoor temperature and an outdoor temperature. If the indoor tem perature station does not display bot h temperat ures after the 10 minutes please retry the set up as stated above.
5 NOTE: Fog and mist will not harm your remote t emperature sensor but direct rain must be avoided. To complet e the set up of your indoor temperature station after the 10 minutes have passed please follow the steps in the detailed set up guide on page 8-9.
6 ADDITIONAL EQUIPMENT (not included) 1. 1 Philips screwdriver. 2. 2 Fresh AA Alkaline batteries. 3. 2 Fresh AA Alkaline batteries DETAILED SETUP GUIDE Battery Installation Figure 2 Holder Figure 1 .
7 1. Install 2 AA batteries in the remote temperature sensor. Make sure they do not spring free, or start-up problems may occur. 2. Install 2 AA batteries in the indoor weather station. Do not press any buttons for at least ten minutes. Setting the time 1.
8 6. Press and release the “+” key to advance the minutes. 7. Press and release the “SET” key to exit programming. FEATURES Minimum and Maximum Temperatures 1. Press and release the “ MIN/MAX” button, “MAX” appears between the indoor and remote temperatures.
9 while viewing the minimum or maximum tempera t ure s. Resetting Min and Max Te mpe r atur e s To reset both t he mi ni mum a n d ma xi mum temperatures—press and hold the “MIN/MAX” button for 5 seconds.
10 on its LCD, and the TX3UP will monitor the temperature of water or soil via a probe. When setting up multiple remote temperature sensors, it is important to remove the batteries from all existing units in operation, then to insert batteries first into all the remote temperature sensors.
11 over time. The WS-7208UF averages pas t air-pressure readings to provide an accurate forecast, creating a necessity to disregard all weather forecasting for 12-24 hours after the unit has been set-up, reset, or moved from one altitude to another (i.
12 Sunny —indicates that the weather is expected to improve (not that the weather will be sunny). Sun with Clouds — indicates that the weather is expected to be fair (not that the weather will be sunny with clouds). Clouds with Rain — indicates that the weather is expected to get worse (not that the weather will be rainy).
13 occur quickly. If the symbols do not change then the weather has not changed, or the change has been slow and gradual. Weather Tendency Arrows Other possible displays in the FORECAST LCD are 2 weather tendency arrows, one that points up (on the left side of the LCD) and one that points down (on the right side of the LCD).
14 The sending range is 80ft; obstacles such as walls, concrete, and large metal objects will reduce the range. Place both units in their desired location before permanently mounting. Remote Temperature Sensor Remove the mounting bracket from the remote temperature sensor.
15 Using the integrated hanging hole on the back of the unit, slip indoor weather station over the screw and pull down to secure. TROUBLESHOOTING NOTE: For problems not solved, please contact La Crosse Technology via e-mail or phone, or visit our website, www.
16 straight-line signal is not passing through more than two or three walls. Problem: Temperatures do not match if units are placed next to each other. Solution: Each temperature sensor is manufactured to be accurate to within 1 degree plus or minus and under normal conditions, so two sensors could be as much as 2 degrees different.
17 is difficult to compensate for the above factors and obtain an accurate comparison. MAINTENANCE AND CARE INSTRUCTIONS • Extreme temperatures, vibration, and shock should be avoided to prevent damage to the units. • Clean displays and units with a soft, damp cloth.
18 SPECIFICATIONS Transmitting Frequency 433MHz Measuring Temperatures Indoor Weather Station 32 ° F to 156.2 ° F with 0.2 ° F resolution (0 ° C to 69.0 ° C with 0.1 ° C resolution) Remote Temperature Sensor -21.8 ° F to 156.2 ° F with 0.2 ° F resolution (-29.
19 Indoor Weather Station 2 x AA, 1.5V Dimensions: (L x W x H) Indoor Weather Station 2.90 x 1.05 x 6.20 in. Remote Temperature Sensor 1.57 x 0.85 x 5.00 in. Battery life Approximately 1 year WARRANTY INFORMATION La Crosse Technology provides a 1-year warr anty on this indoor weather station.
20 batteries, or the indoor weather stations inability to receive a signal due to any source of interference. LA CROSSE TECHNOLOGY WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS INDOOR WEATHER STATION.
21 e-mail: support@lacrossetechnology.com (warranty work) sales@lacrossetechnology.com (information on other products) web: www.lacross ete chnology.com FCC DISCLAIMER This device complies with part 15 of the FCC rules.
22 FCC ID: OMO-01RX (Receiver), OMO-01TX (transmitter) THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND 2. THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Ein wichtiger Punkt beim Kauf des Geräts La Crosse Technology WS-7208U (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie La Crosse Technology WS-7208U noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für La Crosse Technology WS-7208U - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von La Crosse Technology WS-7208U reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über La Crosse Technology WS-7208U erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon La Crosse Technology WS-7208U besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von La Crosse Technology WS-7208U verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit La Crosse Technology WS-7208U. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei La Crosse Technology WS-7208U gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
