Benutzeranleitung / Produktwartung WS-7013U-IT des Produzenten La Crosse Technology
Zur Seite of 28
1 WS-7013U-IT Wireless 915 MHz Temperature Station Instruction Manual.
2 TABLE OF CONTENTS Topic Page Inventory of Contents Quick Setup Detailed Setup G uide Battery Installation Setting the Time Features Minimum and Maxi mum Temperatures Resetting Minimum and Maximum Te.
3 INVENTORY OF CONTENTS 1. The indoor temperature station (Figure 1) 2. The remote temperature sensor (TX29U- IT) and mounting bracket. (Figure 2) 3. 3 each, 1/2” Philips screws. 4. One strip of double sided adhesive tape. 5. Instruction Manual and Warranty Card.
4 ADDI TION AL EQU IPM ENT (not included) 1. 1 Philips screwdriver. 2. 2 Fresh AAA 1.5V batteries. 3. 2 Fresh AA 1.5V batteries QUICK SETUP Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart.
5 3. Place the batteries into the remote temperature sensor first then into the indoor temperature station. (All remote temperature sensors must be started before the indoor temperature station) 4.
6 walls, floors, ceilings, thick trees, etc.) will effectively cut signal range in half. Example : A wireless weather station with a 330 feet range is mounted on an interior wall, so that the signal has to pass through one interior wall, one exterior wall, and across the 10 feet width of the room between the 2 walls.
7 To complete the set up of your indoor temperature station after the 15 minutes have passed please follow the steps below. 1. Press and hold the “SET/CH” button for 5 seconds. Note: A “12h” or “24h” will appear on the top line. (“12h” for AM/PM, “24h” f or military time) 2.
8 6 . When the correct hour is shown, press and release the “SET” button once. Press and release the SET button once more and you are done. DETAILED SETUP GUIDE BATTERY INST ALLATION - When one Temperature sensor is bein g used 1. First, insert the batteries to the Temperature sensor (see “ A.
9 data signal from the sensor. The outdoor temperature and humidity should then be displayed on the Temperature Station. If this does not happen after 2 minutes, the batteries will need to be removed from both units and reset from step 1 and the signal reception icon is no longer shown.
10 a. Remove the battery cover on the backside. To do this, push up and pull out. b. Observing the correct polarity, install 2 AAA batteries. c. Replace battery cover. d. Wait 15 minutes to allow both the indoor and outdoor temperatures are shown on the indoor temperature station.
11 * When the signal is successfully received by the Temperature Station, the icon will be switched on. (If not successful, the icon will not be shown in LCD) So the user can easily see whether the last reception was successful (icon on) or not (icon off).
12 910MHz. This will also be done for re- synchronization. SETTING THE TIME 1. Press and hold the “ SET/CH” button for 5 second, “12h” will appear in the TIME LCD. 2. Press and release the “ MIN/ MAX ” button to select either 12h time (am/pm) or 24h time 3.
13 Note: if “12h” is selected, the temperature is displayed in degree Fahrenheit. If “24h” is selected, the temperature is displayed in degree Celsius FEATURES MINIMUM & M AXIMUM TEMPERATURES 1.
14 temperature sensor units with the WS-7013U- IT. These extra sens ors can be purchased through the same dealer as this unit. 1. Remove all the batteries from the receiver and sensor(s) and wait 60 seconds. During these 60 seconds, press any button 20 times to discharge any excess pow er.
15 5. Insert the batteries to the second sensor as soon as the outdoor temperature readings from the first sensor are displayed on the Temperature station. NOTE: You must insert the batteries into the second sensor w ithin 45 seconds of reception of the first sensor.
16 NOTE: You must insert the batteries into the third sensor within 45 seconds of reception of the second sensor. IMPORTANT: Transmission problems will arise if the setting for multiple sensors is not followed as described above.
17 3. To reset the Minimum/Maximum readings, press and hold the “MIN/MAX” button for four seconds. MOUNTING Note: To achieve a true temperature rea ding, avoid mounting in direct sunlight. We recommend that you mount the remote temperature sensor on an outside North- facing wall.
18 b. Mount using either screws or adhesive tape. c. Reattach the temperature sensor to the mounting bracket. 2. TH E TEM PE R ATURE ST ATIO N e. The indoor temperature station comes with the table stand already mounted. If you wish to use the table-stand, all that is required is to place the indoor temperature station in an appropriate location.
19 Problem: Th e LCD is faint Solution : Replace batteries Problem: No outdoor temperature I displayed. Solution : 1) Remove all batteries, reinsert into remote temperature sensor first, and then into the indoor temperature station. 2) Place remote temperature sensor closer to the indoor temperature station.
20 The indoor sensor is less responsive to ambient air currents because of the shielding effect of the display's case. In addition, the case can act as a heat sink to absorb and store heat from external sources (i.e. handling of the case or radiant heat).
21 9 Opening the casings invalidates the warranty. Do not try to repair the unit. Contact La Crosse Technology for repairs. SPECIFIC ATIONS Transmitting Frequency 915MHz Measuring Temperatures Indoor Temperature Station: Indoor 14.1 ° F to 139.8.2 ° F with 0.
22 Indoor Temperature Station 2 x AAA, 1.5V Dimensions: (H x W x D) Indoor Temperature Station 4.3 x 2.75 x .92 in. (excluding table stand) (110 x 90 x 23.
23 authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La Crosse Technolog y, Ltd’s authorized service center.
24 ground return shipping charges to the o wner of the product to a USA address only. Your La Crosse Technology, Ltd warrant y covers all defects in material and workmanship with the following specifi.
25 misrepresentation by the seller or performance variations resulting from installation-related circumstances. LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE O PERATION OR MALF UNCTIO N OF THIS PRODUCT.
26 Fax: 608.796.1020 e-mail: support@lacrossetechnology.com (warranty work) sales@lacrossetechnology.com (information on other products) web: www.lacrossetechnology.com Questions? Instructions? Please visit: www.lacrossetechnology.com/7013 All rights reserved.
27 FCC ID: OMOTX29U (sensor) RF Exposure mobile: The internal / external antennas used for this mobile sensor must provide a separation distance of at least 20 cm (8 inches) from all persons and must not be co-located or operating in conjunction with any other antenna or sensor.
28 interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarante e that interference will not occur in a particular installation.
Ein wichtiger Punkt beim Kauf des Geräts La Crosse Technology WS-7013U-IT (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie La Crosse Technology WS-7013U-IT noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für La Crosse Technology WS-7013U-IT - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von La Crosse Technology WS-7013U-IT reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über La Crosse Technology WS-7013U-IT erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon La Crosse Technology WS-7013U-IT besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von La Crosse Technology WS-7013U-IT verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit La Crosse Technology WS-7013U-IT. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei La Crosse Technology WS-7013U-IT gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
