Benutzeranleitung / Produktwartung WS-7013TWC des Produzenten La Crosse Technology
Zur Seite of 23
Quick Start for your WS-7013U Hint: Use good quality Alkaline Batteri es and avoid rec hargeable batteries. 1. Have the indoor station and outdoor remote 3 to 5 ap art. 2. Batteries shoul d be out of both unit s for 10 minut es. 3. Place the batteries into the outdoor remote first then into the indoor station.
1 7, 0 ( WS-7013U Wireless 433 MHz Temperature Station Instruction Manual.
2 TABLE OF CONTENTS Topic Page Inventory of Contents 1 Quick Setup 2 Detailed Setup Guide Battery Installation 3-4 Setting the Time 5 Selecting Units of Measurement 6 Features Minimum and Maximum Temp.
1 INVENTORY OF CONTENTS 1. The Indoor Temperature Station (Figure 1) 2. The Remote Control Sensor (TX2U) and mounting bracket. (Figure 2) 3. 3 each, 1/2” Philips screws. 4. One strip of double sided adhesive tape. 5. Instruction Manual and Warranty Card.
2 QUICK SETUP 1. Insert two AAA batteries into the Remote Control Sender. 2. Insert two AAA batteries into the Indoor Temperature Station. 3. Wait 5-6 minutes, or until the outdoor temperature is displayed in the OUTDOOR LCD of the Temperature Station.
3 DETAILED SETUP GUIDE I. BATTERY INSTALLATION A. REMOTE CONTROL SENDER 1. Remove the mounting bracket. 2. Remove battery cover 3. Observing the correct polarity, install 2 AAA batteries—make sure they do not spring free, or start-up problems may occur.
4 7, 0( 1. Remove the battery cover on the backside. To do this, push up and pull out. 2. Observing the correct polarity, install 2 AA batteries. 3. Replace battery cover. 4. Wait 5-6 minutes or until both indoor and outdoor temperatures are shown on the Indoor Temperature Station.
5 II. TIME A. SETTING THE TIME 1. Press and hold the SET button for 1 second. “12h” will appear in the TIME LCD. 2. Use the MIN/MAX button to select either 12h time (am/pm) or 24h time 3. Press the SET button 2 times, the hour will flash in the upper left corner.
6 III. UNITS OF TEMPERATURE MEASURE A. SELECTING UNITS OF MEASUREMENT 1. Press and hold the SET button for 1 second. 2. Press the SET button again. “ ° F” will appear in the TIME LCD. 3. Press the MIN/MAX button to shift between ° F and ° C. 4.
7 time of occurrence of the value for outdoor temperature will also flash. B. RESETTING THE MINIMUM AND MAXIMUM TEMPERATURES 1. To reset both the minimum and maximum temperat ure s—pre ss a nd hold the RESET/+ button for 4 seconds. C. ADDING ADDITIONAL REMOTE CONTROL SENDERS (OPTIONAL) 1.
8 display the temperature on its LCD, and the TX3UP will monitor the temperature via a probe for use in pools, spas, etc. 2. Note: When setting up multiple units it is importa nt to remove the batteries from all existing units in operation, then to insert batteries first into all the Remote Control Sender units, and in n umeric sequence.
9 procedures seen in section I. A) of the Detailed Set-Up Guide). 7. Install batteries into the Indoor Temperature Station. 8. Follow the Detailed Set-Up Guide for programming and operating instructions. D. VIEWING AND OPERATING WITH MULTIPLE REMOTE CONTROL SENDER UNITS 1.
10 minimum and maximum outdoor temperature. 3. To reset the Mi ni mum/ Ma xi mum readings press and the MIN/MAX button for four seconds. V. MOUNTING A. Note: To achieve a true temperature reading, avoid mounting in direct sunlight. We recommend that you mount the Sender on an outside North-facing wall.
11 1. The Indoor Temperature Station comes with the table stand already mounted. If you wish to use the table- stand, all that is required is to place the Indoor Temperature Station in an appropriate location. 2. To wall mount, remove the table stand.
12 TROUBLESHOOTING NOTE: For problems not solved, please contact La Crosse Technology via e-mail or phone, or visit our website, www.lacrossetechnology.com Problem: The LCD is faint Solution: 1) Replace batteries Problem: No outdoor temperature is displayed.
13 Solution: Each temperature sensor is manufactured to be accurate to within 1 degree plus or minus and under normal conditions; so two sensors could be as much as 2 degrees different. However, the difference can be exaggerated further because the sensors are designed for different working environments.
14 MAINTENANCE AND CARE INSTRUCTIONS • Extreme temperatures, vibration, and shock should be avoided to prevent damage to the units. • Clean displays and units with a soft, damp cloth. Do not use solvents or scouring agents; they may mark the displays and casings.
15 SPECIFICATIONS Transmitting Frequency 433MHz Measuring Temperatures Temperature Station: Indoor 32 ° F to 156.2 ° F with 0.2 ° F resolution. (0 ° C to 69.0 ° C with 0.1 ° C resolution). Temperature Station: Outdoor -21.8 ° F to 156.2 ° F with 0.
16 Dimensions: (L x W x H) Temperature Station 2.75 x .92 x 4.3 in. (excluding table stand) (90 x 23.6 x 110 mm). Remote Control Sender 2.32 x 0.86 x 2.
17 herein, with new or recondit ioned parts or products if found to be defective dur ing the limited warranty period specified above. All replaced parts and products become the property of La Crosse Technology, Ltd and must be returned to La Crosse Technology, Ltd.
18 alterations by someone ot her than an authorized La Crosse Technology, Ltd aut horized service center; (6) units used for other than home use (7) applications and uses that this product was not intended or (8) the products inability to receive a signal due to any source of interference.
19 For warranty w ork, technic al support, or information contact: La Crosse Technology 2809 Losey Blvd. S. La Crosse, WI 54601 Phone: 608.782.1610 Fax: 608.796.1020 e-mail: support@lacrossetechnology.com (warranty w ork) sales@lacrossetechnology.com (information on other products) web: www.
20 FCC DISCLAIMER This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesir ed operation.
Ein wichtiger Punkt beim Kauf des Geräts La Crosse Technology WS-7013TWC (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie La Crosse Technology WS-7013TWC noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für La Crosse Technology WS-7013TWC - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von La Crosse Technology WS-7013TWC reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über La Crosse Technology WS-7013TWC erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon La Crosse Technology WS-7013TWC besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von La Crosse Technology WS-7013TWC verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit La Crosse Technology WS-7013TWC. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei La Crosse Technology WS-7013TWC gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
